Impex MWM-1558 User's Manual
Contents
1. C Attach a Pulley to the bracket Secure it with one M10 x 1 37 Allen Bolt 69 two Y 34 Washers 80 and one M10 Aircraft Nut 82 D Draw the Cable around the Pulley then downward Attach the Cable to a Crossed Double Floating Pulley Bracket 17 Install another Pulley Let the Bracket hanging for now E Pull the Cable around the Pulley then upward to the left Swivel Pulley Bracket Repeat Step C above to install a Pulley F Draw the Cable to the left Butterfly Attach the end to the hook on the Left Butterfly DIAGRAM 6 STEP7 See Diagram 7 amp Cable Loop Diagram A Attach the 128 Lower Cable 32 to the open bracket on the bottom of the Leg Developer 7 B Attach a Pulley to the bracket Secure it with one M10 x 1 37 Allen Bolt 69 two 34 Washers 80 and one M10 Aircraft Nut 82 Draw the Cable underneath the Pulley to the open bracket on the Main Base Frame 48 Repeat Step B above to install a Pulley Draw the Cable underneath the Pulley along the top of the Main Base Frame through the hole on the bottom of the Front Vertical Frame to an open bracket Install another Pulley Pull the Cable upward to the Crossed Double Floating Pulley Bracket 417 previously installed in Step 6 Install another Pulley Draw the Cable around the Pulley then downward to the open bracket on the Main Base Frame Install another Pulley Pull the Cable around the Pulley then upward to the Double Float2. and Rear Base Frame 2 Secure them with six M10 x 5 8 Allen Bolts 71 and 2 34 Washers 80 D From the back of the Covers secure the two covers together with four M5 x 3 8 Philips Screws and M5 Aircraft Nuts 38 DIAGRAM 8 A PARTS LIST KEY NO DESCRIPTION Main Seat Support Rear Base Frame Front Vertical Frame Upper Frame Left Butterfly Right Butterfly Leg Developer Main Base Frame Butterfly Pulley Bracket 10 Arm Curl Stand 11 Front Press Base 12 Front Press Handle 13 Selector Rod 14 Lat Bar 15 Arm Curl Handle 16 Double Floating Pulley Bracket 17 Crossed Double Floating Pulley Bracket 18 Swivel Pulley Bracket 19 Arm Curl Handle Tube 20 Guide Rod 21 Left Weight Stack Cover 22 Right Weight Stack Cover 23 Foam Tube 24 4 34 x 2 Bracket 25 5 V x 2 Bracket 26 Rear Base Frame Bracket 27 Foot Plate 28 Selector Stem 29 Weight Plate 30 L shaped Pin 31 Upper Cable 131 32 Lower Cable 128 33 Butterfly Cable 119 34 Seat 35 Backrest Board 36 Arm Curl Pad 37 Lock Ring 38 M5 Aircraft Nut 39 Ankle Strap 40 Lock Knob 41 Y 1 1 8 Bushing 42 1 77 Bushing 43 Long Axle 44 Leg Developer Axle 45 Long Chain 46 Short Chain 47 Sliding Sleeve 48 Handle Grip 49 Lat Bar Grip 50 C clip O 0 314 Oo s ON o lt 17 Front Base Frame End Cap Rear Base Frame End Cap 2 x 1 End Cap 2 Y x 2 End Cap 2 Square End Cap Y 1 Cone shaped End Ca
3. Nut Qty 32 Nut Qty 2 Qty 4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches two Allen Wrenches and one Philips Screwdriver NOTE It is strongly recommended this machine to be assembled by two or more people to avoid possible injury STEP1 See Diagram 1 A Attach the Front Vertical Frame 3 to the Main Base Frame 8 Secure it with two M10 x 2 34 Carriage Bolts 77 one 5 1 x 2 Bracket 25 two Y 34 Washers 80 and two M10 Aircraft Nuts 82 DO NOT tighten all the nuts and bolts yet B Push two Y 2 7 Guide Rod Rubber Bumpers 62 onto the Guide Rods 20 from the bottom Insert the Guide Rods into the holes on the Rear Base Frame 2 Secure it with two M10 x 1 Allen Bolts 70 and Y 34 Washers 80 from the bottom of the Rear Base Frame C Connect the Main Base Frame 8 to the Rear Base Frame 2 Secure it with two M10 x 2 34 Carriage Bolts 77 one Rear Base Frame Bracket 26 two 34 Washers 80 and two M10 Aircraft Nuts 82 STEP 2 See Diagram 2 A Slide the 9 Weight Plates 29 onto the Guide Rods 20 Align the holes of the Weight Plates Insert the Selector Rod 13 through the center hole Use a L shaped Pin 30 to select the number of plates B Slide the Selector Stem 28 onto the Guide Rods C Attach the Upper Frame 4 to the two Guide Rods Place the Upper Frame onto the F
4. Frame 4 Note The Ball Stopper on the cable should be underneath the Frame Attach a Pulley 260 to the open bracket Secure it with one M10 x 1 37 Allen Bolt 69 two 32 Washers 80 and one M10 Aircraft Nut 82 Draw the Cable towards the back of the machine to the open bracket on the Upper Frame Repeat step B above to install a Pulley Draw the Cable around the Pulley then pull back towards the opening on the Front Press Base 411 Attach a Pulley to the opening on the Front Press Base Secure the Pulley with one M10 x 6 7 8 Allen Bolt 65 and one M10 Aircraft Nut 82 Draw the Cable around the Pulley and through the opening to the open bracket on the Front Vertical Beam 3 Repeat step B above to install another Pulley Draw the Cable around the Pulley then pull the Cable downwards Attach the Cable to a Double Floating Pulley Bracket 416 Install another Pulley Let the bracket hanging for now Pull the Cable upward to the open bracket on the back of Upper Frame Install two pulleys to the bracket Pull the Cable downward between the two Guide Rods to the Selector Rod 413 Thread the bolt at the end of the Cable into the opening on top of the Selector Rod 13 to secure the Cable 11 DIAGRAM 5 22 12 STEP 6 See Diagram 6 8 Cable Loop Diagram A Attach one end of the 119 Butterfly Cable 33 to the hook on the Right Butterfly 6 B Draw the Cable to the right Swivel Pulley Bracket 418
5. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM 1558 Retain This Manual for Reference 07 20 05 OWNER S MANUAL MPZX MARCY HOME GYM MW M 1558 IMPEX INC 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN scwcd ite dicite a ee ee cC Ea EE 1 IMPORTANT SAFETY NOTICE Sx istas estas ated ada 2 HARDWARE PAG Kina seele 3 ASSEMBLY INSTRUCTIONS puntuacion a 6 PARTS Srs A ORCO EE ide 17 RESISTANGE GHAR T usa sea au a ie 18 WARRANTY Gen DNET OWO Doer parker R AR AWA RZ ANO Er AE NOIN m aja dein dd 19 ORDERING PART Sa debent eder v ki t kk oikeisto epa ot 19 BEFORE YOU BEGIN Thank you for selecting the MARCY MWM 1558 HOME GYM by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOOL FHEE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Servic
6. d 35 to the Front Vertical Frame 3 Secure it with two M8 x 3 3 8 Allen Bolts 72 and 5 8 Washers 81 STEP 4 See Diagram 4 A Attach the Main Seat Support 1 to the Front Vertical Frame 3 Secure it with two M10 x 3 V7 Carriage Bolts 76 one 4 32 x 2 Bracket 24 two Y 34 Washers 80 and two M10 Aircraft Nuts 82 B Attach the Leg Developer 7 to the bracket on the Main Seat Support Secure it with a Leg Developer Axle 44 two M10 x 5 8 Allen Bolts 71 and two 32 Washers 80 C Insert two Foam Tubes 23 halfway through the holes on the Leg Developer and Main Seat Support Push four Foam Rolls 58 onto the Foam Tubes from both ends Plug four Foam Roll End Caps 57 onto the ends D Place the Seat 34 onto the Main Seat Support 1 Secure it with two M8 x 2 7 Allen Bolts 73 and Y 5 8 Washers 81 E Attach the Arm Curl Pad 36 to the Arm Curl Stand 10 Secure it with two M8 x 5 8 Allen bolts 74 and 5 8 Washers 481 Insert the Arm Curl Stand into the front opening on the Main Seat Support Secure it with a Lock Knob 40 F Attach two Foot Plates 27 to the Main Base Frame 8 Secure them with two M10 x 3 2 Carriage Bolts 76 34 Washers 80 and M10 Aircraft Nuts 82 DIAGRAM 4 CABLE LOOP DIAGRAM STEP 5 See Diagram 5 8 Cable Loop Diagram A Attach the 131 Upper Cable 431 to the opening at the front of the Upper
7. e Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 10 11 12 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine Only one person at a time should use the machine If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors Keep hands away from all moving parts Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance Before using the machine to exercise always do s
8. ing Pulley Bracket 16 previously installed in Step 5 Install another Pulley Draw the Cable around the Pulley then pull downward Connect the Cable to a C clip 450 then connect the C clip to a Short Chain 446 Connect the Short Chain to the bracket on the back of the Front Vertical Frame Secure it with one M10 x 1 Allen Bolt 70 two 32 Washers 80 and one M10 Aircraft Nut 82 Adjust the tension of the Cable by adjusting the length of the Short Chain For best performance of the machine adjust the Chain so the Selector Stem Top Plate on the weight stack is 14 above the first plate While adjusting the weight stack push down on the Selector Stem to close up the gap then pin the plates This will remove the slag in the cable system so the range of motion is smooth and tight 14 DIAGRAM 7 15 STEP 8 See Diagram 8 A Attach a Short Chain 46 to the Upper Cable 31 by using a C clip 50 Attach the Lat Bar 14 to the Chain by using another C clip Adjust the length of the Chain to obtain desired Lat Bar exercise B Attach a Long Chain 45 to the Lower Cable 32 by using a C clip 50 Attach the Arm Curl Handle 415 to the Chain by using another C clip Adjust the length of the Chain to obtain the desired Arm Curl exercise Remove the Chain and the Handle when using the Leg Developer C Attach Left amp Right Weight Stack Covers 21 amp 22 to the Upper Frame 4 Main Base Frame 8
9. nt parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase Bom 19
10. p Foam Roll End Cap Foam Roll Butterfly Foam Roll Pulley Y 1 ve Rubber Bumper Y 2 12 Guide Rod Rubber Bumper 1 34 Rubber Bumper Y 1 Bushing M10 x 6 7 8 Allen Bolt M10 x 4 3 8 Allen Bolt M10 x 3 3 8 Allen Bolt M10 x 2 12 Allen Bolt M10 x 1 37 Allen Bolt M10 x 1 Allen Bolt M10 x 5 8 Allen Bolt M8 x 3 3 8 Allen Bolt M8 x 2 1 Allen Bolt M8 x 5 8 Allen Bolt M6 x 1 5 8 Hex Bolt M10 x 3 Carriage Bolt M10 x 2 34 Carriage Bolt M6 x 5 8 Philips Screw M5 x 3 8 Philips Screw O 54 Washer 5 8 Washer M10 Aircraft Nut M6 Aircraft Nut N D O0 FRN 40rInmrnmnmmocooci mm o0o nm n mse50mcornmnm m N N une yea 10 91e Ay1exng 103 sanjeA Aiea Kew sqyGrom jenpy e3euixoadde o4e sioquinn sql OT SIYBISM e3ejd UDEJ 970N JYVHO 39NVISIS33 LHOI3M 8SSTWMW 18 IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This
11. ront Vertical Frame 43 D Secure the Upper Frame to the Guide Rods with two M10 x 1 Allen Bolts 70 and Y 34 Washers 80 E Secure the Upper Frame to the Front Vertical Frame with two M10 x 3 Carriage Bolts 76 one 5 1 x 2 Bracket 25 two 32 Washers 80 and two M10 Aircraft Nuts 482 Tighten all bolts and nuts previously installed STEP3 See Diagram 3 A B C M J a O Attach the Front Press Base 11 to the Upper Frame 4 Secure it with one Long Axle 43 two O 34 Washers 80 and two M10 Aircraft Nuts 82 Attach the Right Butterfly 6 to the Front Press Base Secure it with one M6 x 1 5 8 Hex Bolt 275 Lock Ring 37 and M6 Aircraft Nut 83 Slide a Butterfly Foam Roll 59 onto the Right Butterfly arm Attach a Front Press Handle 12 to the Right Butterfly Secure it with a M10 x 3 3 8 Allen Bolt 67 Repeat the Step B amp C above to install the Left Butterfly 45 Attach the Butterfly Pulley Bracket 29 to the Front Vertical Frame 43 Secure it with one M10 x 4 3 8 Allen Bolt 66 two 34 Washers 80 and one M10 Aircraft Nut 82 Attach Swivel Pulley Brackets 18 to each end of the Butterfly Pulley Bracket 9 Secure each Bracket with one M10 x 2 Y Allen Bolt 68 two Y 34 Washers 80 and one M10 Aircraft Nut 282 Do Not over tighten make sure the bracket 18 is able to swivel freely Attach the Backrest Boar
12. tretching exercises to properly warm up Never operate the machine if the machine is not functioning properly A spotter is recommended during exercise WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS HARDWARE PACK Yo Q 30 L shaped Pin Qty 1 44 Leg Developer Axle Qty 1 43 Long Axle Qty 1 37 Lock Ring Qty 2 46 Short Chain Qty 2 50 C clip Qty 5 45 Long Chain Qty 1 3 HARDWARE PACK d mm 65 M10 x 6 7 8 Allen Bolt Qty 1 J M H66 M10 x 4 3 8 Allen Bolt Qty 1 J m 67 M10 x 3 3 8 Allen Bolt Qty 2 868 MIO x 2 1 2 Allen Bolt Qty 2 M m 69 M10 x 1 3 4 Allen Bolt Qty 15 75 M6 x 1 5 8 Hex Bolt Qty 2 870 MIO x 1 Allen Bolt Qty 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 HARDWARE PACK 76 M10 x 3 1 2 Carriage Bolt Qty 6 77 M10 x 2 3 4 Carriage Bolt Qty 4 IB 72 M8 x 3 3 8 Allen Bolt Qty 2 73 M8 x 2 1 2 Allen Bolt Qty 2 HIE 74 M8 x 5 8 Allen Bolt Qty 2 H B ms 4800 3 4 Washer 819 5 8 Washer 82 M10 Aircraft 83 M6 Aircraft 38 M5 Aircraft Nut Qiy 62 Oty 6
13. warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replaceme
Download Pdf Manuals
Related Search