Home

IBM MT 2675 User's Manual

Contents

1. Screw cap Torque 39 2 Ncm 4 kgfcm 39 2 Ncm 4 kgfcm Screw quantity M2 5 x 3 mm O nylon coated 2 M2 5 x 3 mm nylon coated 1 When installing When installing part H in the preceding figure fit the screw hole plate and the claw into the square holes on the bottom side of Ey H and then slide H in the direction of the arrow I Then tighten the screw continued ThinkPad TransNote 75 Removing and replacing a FRU Step Screw quantity Screw cap Torque H M2 5 x 3 mm O 39 2 Ncm nylon coated 1 4 kgfcm g M2 5 x 3 mm DO 39 2 Ncm nylon coated 1 4 kgfcm 76 ThinkPad TransNote Removing and replacing a FRU For a left handed model Step Screw quantity Screw cap Torque M2 5 x 3 mm O 39 2 Ncm nylon coated 2 4 kgfcm M2 5 x 3 mm 39 2 Ncm nylon coated 1 4 kgfcm When installing When installing part H in the preceding figure fit the screw hole plate and the claw into the square holes on the bottom side of Ey H and then slide H in the direction of the arrow D Then tighten the screw continued ThinkPad TransNote 77 Removing and replacing a FRU Step Screw quantity Screw cap Torque H M2 5 x 3 mm C 39 2 Ncm nylon coated 1 4 kgfcm a M2 5 x 3 mm D 39 2 Ncm nylon coated 1 4 kgfcm 78 ThinkPad TransNote Remo
2. 138 ThinkPad TransNote LCD FRUs Parts list No FRU P N 1 LCD front bezel 08K6462 2 Inverter card 08K3154 3 LCD panel 10 4 in TFT Hitachi 05K9623 4 LCD cable 27L0544 5 Rear cover 08K6464 ThinkPad TransNote 139 Parts list Keyboard Language P N Belgian 02K5498 Danish 02K5496 Dutch 02K5501 Spanish 02K5503 French 02K5493 German 02K5492 Italian 02K5497 Japanese 02K5504 Norwegian 02K5495 Portuguese 02K5500 Swedish or Finnish 02K5494 Swiss 02K5499 U K English 02K5502 U S English 02K5218 Endurimer leather cover replacing kit FRU P N Right handed model to left handed model Pen holder cap L Pen holder Pen protector Tape for base plate Tape for digi base Tape for digi base3 Velcro tape Screw caps small Screw caps Replacing kit for right handed to left handed 08K7361 Endurimer for left handed 04P3470 Leather cover for left handed 04P3474 Left handed model to right handed model Pen holder cap R Pen holder Pen protector Tape for base plate Tape for digi base Tape for digi base3 Velcro tape Screw caps small Screw caps Replacing kit for left handed to right handed 08K7360 Endurimer for right handed 08K6572 Leather cover for right handed 04P3472 140 ThinkPad TransNote Miscellaneous
3. 2 gt gt WY YY WY La c El Left handed model to right handed model a SS A gt h continued ThinkPad TransNote 127 Removing and replacing a FRU 8 Paste new tape for digitizer and digitizer base tape H on the bottom side of the computer side and then remove the other one E Right handed model to left handed model EN l de gt gt gt gt gt B5 E X E K E IC I Left handed model to right handed model 9 leather cover See Eis am nace na Note When replacing the Endurimer or the system digi cable make sure that the black connector of the system digi cable is attached to the computer and the white connector is attached to the digital notepad assembly continued 128 ThinkPad TransNote Removing and replacing a FRU 10 Install the computer side to the new Endurimer or leather cover as follows a Connect the system digi cable to the computer side and then paste new system board plate b Paste the new tape Tape for digitizer 2 aligning the r marks on the base plate continued ThinkPad TransN
4. Cross section Torque driver If you have a torque driver refer to the Torque column for each step 50 ThinkPad TransNote FRU replacement notices Make sure you use the correct screw If you have a torque screwdriver tighten all screws firmly to the torque shown in the table Never use a screw that you removed Use a new one Make sure the screws are tightened firmly Retaining serial numbers This section includes the following descriptions Restoring the serial number of the system unit When the computer was manufactured the EEPROM on the system board was loaded with the serial numbers of the system and all major components These numbers need to remain the same throughout the life of the computer If you replace the system board you must restore the serial number of the system unit to its original value Before replacing the system board save the original serial number by doing the following 1 Install the ThinkPad hardware maintenance diskette version 1 61 and restart the computer 2 From the main menu select 1 Set System Identification 3 Select 2 Read S N data from EEPROM The serial number for each device is displayed Write down the serial number of the system unit designated as follows 20 System unit serial number After you have replaced the system board restore the serial number by doing the following 1 Install the ThinkPad hardware maintenance diskette version 1 61 and restart
5. EIBIEESEE SERES ERES E RI E CH ER ERIS EI ThinkPad TransNote 133 Locations Rear view CompactFlash card slot A CompactFlash card eject button Modem connector a Network connector H Universal serial bus USB connector BD External monitor connector Power jack H Security keyhole Ba Port replicator connector PC card slot Hard disk drive 134 ThinkPad TransNote Locations ThinkScribe digital notepad EESEEEEEEEGE Status display Error indicator light ThinkScribe reset switch Page selector Ink Files selector Actions selector Activity indicator light ThinkScribe power button Page Forward pen button Page Backward pen button Cancel pen button OK pen button Ink refill trays Pen holder pa an WW S ThinkPad TransNote 135 Parts list Parts list Overall 136 ThinkPad TransNote The parts marked with asterisk are CRU customer replacable unit Parts list No FRU P N a g g 1 LCD unit see LCD FRUs on page 139 2 Arm unit 08K6466 3 Arm cover 08K6468 4 Cover hard disk drive 08K6481 5 HDD assembly 10 GB 9 5 H 05K9286 Geer M assembly see EQptional FRUS onl 6 PC card slot 08K6594 7 Video card 08K3158 8 Mini PCI modem card CR 08K3338 Mini PCI modem card Ambit 08K3252 9 Fan 08K6475 10 System board 08K3188 11 RJ11 45 card 08K
6. follows Make sure that the front edges of the keyboard are under the frame as shown in the following figure 1 2 Push the E key and D keys and O key and L keys to latch the keyboard to the frame then connect the keyboard connector H 72 ThinkPad TransNote Removing and replacing a FRU 1060 Backup battery and sub battery CAUTION There is a danger of an explosion if the backup battery is incorrectly replaced The lithium battery IBM P N 02K6572 UL recognized component file no MH12210 contains lithium and can explode if it is not properly handled or disposed of Replace only with a battery of the same type To avoid possible injury or death do not 1 throw or immerse the battery into water 2 allow it to heat to more than 100 C 212 F or 3 attempt to repair or disassemble it Dispose of it as required by local ordinances or regulations Battery pack 1010 DIMM 1020 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Keyboard 1050 Note Procedure H and H are for the backup battery and Ef are for the sub battery When installing Make sure that the connector is firmly attached continued ThinkPad TransNote 73 Removing and replacing a FRU When installing Make sure that the connector is firmly attached 74 ThinkPad TransNote Removing and replacing a FRU 1070 Digital pen holder kit Battery pack 1010 For a right handed model
7. When installing When installing the video card do the following Make sure that the connector on the bottom side of the video card is firmly connected Make sure that the connector cables are not pinched under the video card as in the following figure 92 ThinkPad TransNote Removing and replacing a FRU 1130 System board and PC card slot assembly Battery pack 1010 DIMM 1020 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 Video card 1120 continued 93 ThinkPad TransNote Removing and replacing a FRU Note Loosen the screw H but do not remove it continued 94 ThinkPad TransNote Removing and replacing a FRU continued ThinkPad TransNote 95 Removing and replacing a FRU When installing Make sure that the keyboard connector is firmly attached continued 96 ThinkPad TransNote Removing and replacing a FRU Step Screw quantity Torque E M2 0 x 3 5 mm nylon coated 4 24 5 Ncm 2 5 kgfcm continued ThinkPad TransNote 97 Removing and replacing a FRU Step Screw quantity Torque E M2 5 x 16 mm nylon coated 5 39 2 Nem 4 kgfcm EJ M2 5 x 4 0 mm nylon coated 11 39 2 Nem 4 kgfcm continued 98 ThinkPad TransNote Removing and replacing a FRU Step Screw quantity Torqu
8. Note In Windows 2000 this combination of buttons functions as a sleep button Customer can change the Settings so that pressing it puts the computer into hibernation mode or even shuts the computer down continued ThinkPad TransNote 39 Product overview Key Description combination Fn F5 Brightness down Fn F6 Brightness up Fn F7 Display output on the computer display an attached external monitor or both Pressing this combination causes the display to go from the computer display to the external monitor then to both together and then to the computer display again Note This function is not supported when the computer is in large desktop mode or when the computer output is driven by the secondary CRT controller Fn F8 Switch the computer screen size between expanded and normal mode if your screen image is smaller than the physical display Note This function is not supported in Windows 2000 Fn F9 Turn hibernation mode on To return to normal operation press the power button for less than four seconds Fn F10 Gives the same function as pressing the print screen key Fn F11 Gives the same function as pressing the scroll lock key Fn Enable or disable the FullScreen Spacebar Magnifier function Fn Insert The volume decreases Fn Delete The volume increases Fn The sound is muted Backspace Fn Gives the same f
9. The computer is in standby mode Blinking green The computer is entering standby mode or hibernation mode or is resuming normal operation This indicator does not blink in Windows 98 Windows 2000 and Windows Me continued 36 ThinkPad TransNote Product overview Indicator Meaning Drive in use Green Note Do not move the system while the Green drive in use light is on Sudden physical shock could cause drive errors Data is being read from or written to the hard disk drive When this indicator is on do not put the computer into standby mode or turn off the computer DH Num lock Green The numeric keypad on the keyboard is enabled To enable or disable the keypad press and hold the Fn key while pressing the NumLk key El Caps lock Green Caps Lock mode is enabled To enable or disable Caps Lock mode press Fn Caps Lock key DH Scroll lock Green Scroll Lock mode is enabled Arrow keys can be used as screen scroll function keys but not to move the cursor To enable or disable Scroll Lock mode press Fn SerLk key Not all application programs support this function Power on Green This indicator stays lighted whenever the computer is on If the power on indicator is on and the standby indicator is off the system is ready to use If both the power on indicator and the standby indicator are on you can use the computer after it ret
10. or services in your country Requests for technical information about IBM products should be made to your IBM authorized dealer or your IBM marketing representative Copyright International Business Machines Corporation 2000 All rights reserved Note to U S Government Users Documentation related to restricted rights Use duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp Copyright IBM Corp 2000 Contents Introduction Important service information Strategy for replacing FRUs How to use error messages Diskette compatibility matrix Safety notices multilingual translations Safety information General safety Electrical safety Safety inspection guide Handling electrostatic discharge sensitive devices Grounding requirements Laser compliance statement General descriptions Read this first What to do first Related service information Service Web site Using Recovery CD Passwords Power management Checkout guide Testing the computer Detecting system information with PC Doctor Power system checkout ThinkPad TransNote Product overview Specifications Status indicators FRU tests Fn key combinations Symptom to FRU index Numeric error codes Error messages Beep symptoms No beep symptoms LCD related symptoms H Identifying problems with the FlipTouch display Identifying problems with the ThinkScribe
11. 8 Press F10 then select Yes in the Setup confirmation window How to remove the hard disk password j X Attention If User only mode is selected and the user HDP is forgotten there is no way to reset it To remove the user HDP that you have forgotten do the following 1 Power on the computer by pressing and holding F1 2 Enter the SVP The IBM BIOS Setup Utility menu appears General descriptions 23 Related service information 3 Select Password using the cursor keys to move down the menu 4 Select Hard disk x password where x is the letter of the hard disk drive A pop up window opens Select either User HDP or Master HDP 6 Enter the master HDP then leave the New Password field blank and press Enter twice Press F10 8 Select Yes in the Setup Configuration window a N Both user HDP and master HDP have been removed Power management To reduce power consumption the computer has three power management modes screen blank standby and hibernation Screen blank mode In screen blank mode the following occurs The LCD backlight turns off The hard disk drive motor stops The speaker is muted To enter screen blank mode press Fn F3 To end screen blank mode and resume normal operation press any key Standby mode When the computer enters standby mode the following events occur in addition to what occurs in screen blank mode The LCD is powered off The hard disk
12. Description Processor Intel mobile Pentium III processor 600 featuring Intel SpeedStep technology Bus architecture PCI Bus Memory standard 64 MB on the system board Memory optional 64 MB 128 MB or 256 MB DIMM card maximum of 320 MB CMOS RAM 114 bytes 4 Kbytes Display 10 4 inch 16M colors SVGA 800x600 resolution TFT color LCD with touch screen display Hard disk drive 10 0 GB 2 5 inch IDE interface UO port External monitor Line in Headphone Microphone Port replicator connector Universal serial bus USB connectors e RJ11 RJ45 CompactFlash CompactFlash card Internal modem 56 6 Kbps Audio Internal microphone Internal speaker Software control volume Infrared transfer IrDA 1 1 PC Card Type l or Il AC adapter 56 watt type or 72 watt type ThinkPad TransNote 35 Product overview Status indicators The system status indicators show the status of the computer as follows LLL Ma E A E te Cl Indicator Meaning H Battery Green The battery is fully charged Blinking green The battery has enough power to operate but is being charged Orange The battery power is low The battery is being charged Blinking orange The battery needs to be charged When the indicator starts blinking orange the computer beeps three times H Standby status Green
13. Save Log Full Erase Hard Drive Quick Erase Hard Drive Power system checkout To verify the symptom of a problem do the following 1 Power off the computer 2 Remove the battery pack 3 Connect the ac adapter 4 Check that power is supplied when you power on the computer Power off the computer Disconnect the ac adapter and install the charged battery pack 7 Check that the battery pack supplies power when you power on the computer oo If you suspect a power problem see the appropriate one of the following power suppl checkouts 28 ThinkPad TransNote Checkout guide Checking the ac adapter You are here because the computer fails only when the ac adapter is used f the power problem occurs only when the port replicator is used replace the port replicator f the power on indicator does not turn on check the power cord of the ac adapter for correct continuity and installation f the computer does not charge during operation go to Checking operational charging 1 Unplug the ac adapter cable from the computer 2 Measure the output voltage at the plug of the ac adapter cable See the following figure Pin Voltage V dc 1 415 5 to 417 0 2 Ground 16 10V If the voltage is not correct replace the ac adapter If the voltage is acceptable do the following Replace the system board f the problem persists go to page 3d Note Noise f
14. bad Default configuration used Reconfigure the settings by running IBM BIOS Setup Utility 0252 Password checksum bad The password is cleared Reset the password by running IBM BIOS Setup Utility 0260 System timer error 1 Replace the backup battery and run IBM BIOS Setup Utility to reset the time and date 2 System board 0270 Real time clock error 1 Replace the backup battery and run IBM BIOS Setup Utility to reset the time and date 2 System board 0271 Date and time error Neither the date nor the time is set in the computer Run IBM BIOS Setup Utility to reset the time and date continued 42 ThinkPad TransNote Symptom to FRU index Symptom or error FRU or action in sequence 0280 Previous boot incomplete Default configuration used 1 e Load Setup Defaults in IBM BIOS Setup Utility DIMM System board 02F4 EISA CMOS not writable Load Setup Defaults in IBM BIOS Setup Utility 2 Replace the backup battery 3 System board 02F5 1 DIMM DIMM test failure 2 System board 02F6 1 DIMM Software NMI failure 2 System board 02F7 1 DIMM Fail safe timer NMI failure 2 System board ThinkPad TransNote 43 Error messages Symptom to FRU index Symptom or error FRU or action in sequence Device address conflict 1 Load Setup Defaults in IBM BIOS Setup Utility Ba
15. if the number of missing discolored or lighted dots in any background is SVGA 5 or more bright dots 5 or more dark dots or a total of 9 or more bright and dark dots Bright dots means pixel is always on white or color Dark dots means Pixel is always off black color Symptom or error FRU or action in sequence No beep power on indicator on and a blank LCD during POST System board LCD backlight not working LCD too dark LCD brightness cannot be adjusted LCD contrast cannot be adjusted 1 Reseat all LCD connectors LCD assembly 3 System board N LCD screen unreadable Characters missing pixels Screen abnormal Wrong color displayed 1 See important note for LCD related symptoms 2 Reseat all LCD connectors 3 LCD assembly 4 System board Horizontal or vertical lines displayed on LCD LCD assembly Note The LCD assembly refers to the internal LCD glass panel assembly and not the complete LCD and back panel 46 ThinkPad TransNote Symptom to FRU index Identifying problems with the FlipTouch display To analyze a problem with the FlipTouch display do the following 1 Make sure that the FlipTouch display is enabled IBM BIOS Setup Utility gt Config gt FlipTouch Display Insert the PC Doctor DOS disk in the diskette drive and turn on the system unit For details on using PC Doctor see Run Diag
16. obvious unsafe conditions such as metal filings contamination water or other liquids or signs of fire or smoke damage 7 Check for worn frayed or pinched cables 8 Check that the power supply cover fasteners screws or rivets have not been removed or tampered with Handling electrostatic discharge sensitive devices Any computer part containing transistors or integrated circuits ICs should be considered sensitive to electrostatic discharge ESD ESD damage can occur when there is a difference in charge between objects Protect against ESD damage by equalizing the charge so that the machine the part the work mat and the person handling the part are all at the same charge Notes 1 Use product specific ESD procedures when they exceed the requirements noted here 2 Make sure that the ESD protective devices you use have been certified ISO 9000 as fully effective When handling ESD sensitive parts Keep the parts in protective packages until they are inserted into the product Avoid contact with other people Wear a grounded wrist strap against your skin to eliminate static on your body Introduction 15 Safety information Prevent the part from touching your clothing Most clothing is insulative and retains a charge even when you are wearing a wrist strap Use the black side of a grounded work mat to provide a static free work surface The mat is especially useful when handling ESD sensitive
17. parts Parts list FRU P N M2 x 3 5 mm flat head 9 M2 5 x 3 mm flat head 33 M2 5 x 4 5 mm flat head 1 M2 5x 4 mm flat head 31 M2 5 x 16 mm flat head 5 M3 x 2 8 mm flat head 4 Screw caps small Screw caps large Screw caps Screw caps pen A Screw caps pen B Blank cap for PC Screw kit including nylon coated screws 04P3291 System miscellaneous parts Insulator on top cover Door compact flash card slots Spring compact flash card slots Latch battery lock Slide knob battery lock Spring battery lock Eject knob battery Eject spring battery Logo a Velcro tape f Tape for base plate g Plate system board Tape for video card Screw caps Screw caps small Screw caps large 04P3293 Miscellaneous parts for system board I O bracket Hex stud Photo switch spacer USB insulator D sub insulator HDD insulator System board insulator DC shield cap Shield tape Shield tape 2 Spring protection sheet Screw M2 5 x 4 mm System board plate Screw caps small Screw caps large Screw caps 04P3292 continued ThinkPad TransNote 141 Parts list FRU P N Miscellaneous parts for Digitizer 08K6569 b Plate for digitizer o Tape for digitizer 2 d Tape for digitizer e Ta
18. potential safety hazards due to attachment of non IBM features or options not covered by this inspection guide If any unsafe conditions are present you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem Consider these conditions and the safety hazards they present Electrical hazards especially primary power primary voltage on the frame can cause serious or fatal electrical shock Explosive hazards such as a damaged CRT face or a bulging capacitor Mechanical hazards such as loose or missing hardware 14 ThinkPad TransNote Safety information To determine whether there are any potentially unsafe conditions use the following checklist at the beginning of every service task Begin the checks with the power off and the power cord disconnected Checklist 1 Check exterior covers for damage loose broken or sharp edges 2 Power off the computer Disconnect the power cord 3 Check the power cord for a A third wire ground connector in good condition Use a meter to measure third wire ground continuity for 0 1 0 or less between the external ground pin and frame ground b The power cord should be the type specified in the parts list c Insulation must not be frayed or worn 4 Remove the cover 5 Check for any obvious non IBM alterations Use good judgment as to the safety of any non IBM alterations 6 Check inside the unit for any
19. properly The System Digi cable 27L0556 is defective If an error message does appear on the LCD ThinkPad TransNote 47 Symptom to FRU index The ThinkScribe digital notepad assembly 02K5881 is defective 3 Run Diagnostics and select ThinkScribe If the device fails any of the tests the ThinkScribe digital notepad assembly 02K5881 is defective 4 Run Interactive Tests and select ThinkScribe LCD Test If the device fails any of the tests the ThinkScribe digital notepad assembly 02K5881 is defective 5 Run Interactive Tests and select ThinkScribe LED Test If the device fails any of the tests the ThinkScribe digital notepad assembly 02K5881 is defective 6 Run Interactive Tests and select ThinkScribe Interactive Test 7 Drag the pen from center top to center bottom and from center left to center right of ThinkScribe digital notepad If all position were detected properly Both ThinkScribe digital notepad and digital pen are OK If one or more positions were not detected properly the ThinkScribe digital notepad assembly 02K5881 is defective If all positions were not detected properly Digital pen 02K5633 battery is depleted or Digital pen 02K5633 is defective or The ThinkScribe digital notepad assembly 02K5881 is defective If the digital pen tip does not move at all when you press down and recording LED does not respond Replace the digitizer pen 02K5633 Intermittent pr
20. substances To avoid possible injury 1 replace only with a battery of the type recommended by IBM or an equivalent 2 keep the battery pack away from fire 3 do not expose it to water or rain 4 do not attempt to disassemble it 5 do not short circuit it Do not put the battery pack in trash that is disposed of in landfills When disposing of the battery comply with local ordinances or regulations continued 56 ThinkPad TransNote Removing and replacing a FRU ThinkPad TransNote 57 Removing and replacing a FRU 1020 DIMM Battery pack 1010 continued 58 ThinkPad TransNote Removing and replacing a FRU Note Loosen the screw Kl but do not remove it continued 59 ThinkPad TransNote ing a FRU Removing and replac 60 ThinkPad TransNote Removing and replacing a FRU DIMM installation notice With the notched end of the DIMM toward the socket insert the DIMM at an angle of about 25 degrees into the socket then press it firmly Pivot the DIMM until it snaps into place H Make sure that the card is firmly fixed in the slot and does not move easily DIMM cover installation notice Attach the latch of the cover firmly by pressing the part shown in the following figure and then tighten the screw ThinkPad TransNote 61 Removing and replacing a FRU 1030 Mini PCI adapter Battery pack 1010 El but do not remove it Note L
21. tests are intended to test only IBM products The use of non IBM products prototype cards or modified options can lead to false indications of errors and invalid system responses 1 Identify the failing symptoms in as much detail as possible 2 Verify the symptoms Try to re create the failure by running the diagnostic test or by repeating the operation Testing the computer The ThinkPad computer has a test program called PC Doctor DOS hereafter called PC Doctor You can detect errors by running the diagnostics test included in PC Doctor This section is an overview of the procedure For details that depend on model unique functions refer to N on page For some possible configurations of the computer PC Doctor might not run correctly To avoid this problem you need to initialize the computer setup by using the IBM BIOS Setup Utility before you run PC Doctor In the IBM BIOS Setup Utility screen press F9 Enter F10 then Enter Note When you initialize the computer configuration some devices are disabled such as the serial port If you test one of these devices you will need to enable it by using PS2 EXE To run the test do as follows Note In the following procedure you can select an item not only with the arrow keys but also with the TrackPoint Instead of pressing Enter click the left button 1 Insert the PC Doctor disk into the diskette drive then power on the computer If the computer canno
22. the computer 2 From the main menu select 1 Set System Identification 3 Select 1 Add S N data from EEPROM Follow the instructions on the screen Note The serial number of the system unit is written on the label attached on the bottom of the computer Retaining the UUID The Universally Unique Identifier UUID is a 128 bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board The algorithm that generates the number is designed to provide ThinkPad TransNote 51 FRU replacement notices unique IDs until the year A D 3400 No two computers in the world have the same number When you replace the system board you must set the UUID on the new system board as follows 1 Install the ThinkPad hardware maintenance diskette version 1 61 and restart the computer 2 From the main menu select 4 Assign UUID A new UUID is created and written If a valid UUID already exists it is not overwritten 52 ThinkPad TransNote Removing and replacing a FRU Removing and replacing a FRU This section presents information and drawings for use in removing and replacing a FRU Be sure to observe the following general rules 1 Do not try to service the computer unless you have been trained and certified An untrained person runs the risk of damaging parts 2 Before replacing any FRU review FERU replacement 3 Begin by removing any FRUs that have to be removed before the fai
23. the cover from right handed orientation to left handed orientation B ovt ThinkPad TransNote 85 Removing and replacing a FRU 1110 Audio card and speaker Battery pack 1010 Hard disk drive and hard disk drive cover 1040 Keyboard 1050 Backup battery and sub battery 1060 Digital pen holder kit 1070 Computer side 1080 After procedure H lay the LCD unit down and then turn the computer side upside down continued 86 ThinkPad TransNote Removing and replacing a FRU Step Screw quantity Torque M2 5 x 4 mm nylon coated 3 39 2 Nem 4 kgfcm ThinkPad TransNote 87 Removing and replacing a FRU When installing Make sure that all of the claws of the cover are firmly fixed into place 88 ThinkPad TransNote Removing and replacing a FRU 1120 Video card Battery pack 1010 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 Step Screw quantity Torque M2 5 x 4 mm nylon coated 2 39 2 Nem 4 kgfcm continued ThinkPad TransNote 89 Removing and replacing a FRU Note Pull the black sheet out from the space between the but do not strip it off from the connector cables video card continued 90 ThinkPad TransNote Removing and replacing a FRU 91 ThinkPad TransNote Removing and replacing a FRU
24. 010 Digital pen 4010 Changing the orientation of a left or right handed model This section contains the procedure for converting a right handed model to a left handed model or vice versa by replacing the Endurimer or leather cover To replace the Endurimer or leather cover do the following 1 Keep the required replacing kit For the content of the kit and the P Ns see continued 124 ThinkPad TransNote Removing and replacing a FRU 5 Paste new velcro tapes on the bottom side of the computer side and remove the old tapes H as shown in the following figures Right handed model to left handed model YA I Left handed model to right handed model We E A E continued ThinkPad TransNote 125 Removing and replacing a FRU 6 Paste new base plate tape on the bottom side of the computer side and then remove the other one H Right handed model to left handed model LJ H 50 5t Jes m Left handed model to right handed model 3t i ts E T continued 126 ThinkPad TransNote Removing and replacing a FRU 7 Paste new velcro tapes on the bottom side of ThinkScribe digital notepad and remove the old tapes B as shown in the following figures Right handed model to left handed model l i
25. 3162 12 RJ11 45 cable 27L0574 13 Base plate 08K6496 14 ThinkScribe digital notepad assembly 02K5881 15 Pen cap 04P3688 16 Standard pen 02K5633 Optional standard pen see EOptiona 17 Endurimer artificial for right handed 08K6572 for left handed 04P3470 Endurimer genuine leather for right handed 04P3472 for left handed 04P3474 18 Pen holder kit for right handed 04P3206 for left handed 04P3320 19 System Digi cable 27L0556 20 Plate for audio card 08K6597 21 Audio card 08K3156 22 DIMM see FOptiona 23 Top cover WW 08K6483 continued ThinkPad TransNote 137 Parts list No FRU P N 24 Sub battery 02K6684 25 Backup battery 02K6682 26 Cover keyboard connector 08K6576 27 Cover Mini PCI slot 08K6574 28 Cover DIMM slot 08K6578 29 Battery pack 6 cell 02K6686 pulpa Id pack 4 cell see 30 Keyboard see K g 31 Pointing stick cap 84G6536 32 AC adapter 72 W 2 pin ASTEC 02K6669 DELTA 02K6673 SANKEN 02K6677 Tun AC adapter see AC adapter 72 W 3 pin DELTA n AC adapter see 33 Power code see EP 34 Port replicator 04P3687 amero Mi replicator see 35 Label of digitizer for non English models for GDL French 08K6566 for EMEA German and French 26P9169 for FUJI Japanese 26P9170 Telephone cable 27L0603 Form holder 08K7156
26. EHTOB Take uzbera te Mpamoro Bo3nelicrBus nasepHoro nyya Ked je laserov jednotka otvoren Vyhnite sa priamemu poh adu a nehladte priamo s optick mi n strojmi do l ta a vyhnite sa priamemu vystaveniu l ov Radiaci n l ser al abrir No mire fijamente ni examine con instrumental ptico el haz de luz Evite la exposici n directa al haz 18 ThinkPad TransNote General descriptions This chapter includes descriptions for any ThinkPad model that has the PC Doctor DOS diagnostics program Some descriptions might not apply to your particular computer Read this first Before you go to the checkout guide be sure to read this section j X Important notes Only certified trained personnel should service the computer Read the entire FRU removal and replacement page before replacing any FRU Use new nylon coated screws when you replace FRUs Be extremely careful during such write operations as copying saving or formatting Drives in the computer that you are servicing sequence might have been altered If you select an incorrect drive data or programs might be overwritten Replace FRUs only for the correct model When you replace a FRU make sure the model of the machine and the FRU part number are correct by referring to the FRU parts list A FRU should not be replaced because of a single unreproducible failure Single failures can occur for a variety of reasons that have nothing
27. IBM Mobile Systems ThinkPad Computer Hardware Maintenance Manual December 2000 This manual supports ThinkPad TransNote MT 2675 m Note Before using this information and the product it supports be sure to read the general information under ENotices on page Second Edition December 2000 The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT ANY WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE LIMITED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer or express or implied warranties in certain transactions therefore this statement may not apply to you This publication could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may make improvements or changes to the products or the programs described in this publication at any time It is possible that this publication may contain references to or information about IBM products machines and programs programming or services that are not announced in your country Such references or information must not be construed to mean that IBM intends to announce such IBM products programming
28. Recovery CD To create Service Partition and install the preloaded system from Recovery CD do the following To create Service Partition SP 1 Erase all partitions on the hard disk drive using FDISK or similar application 2 Boot with Recovery CD and boot diskette if required 3 Amenu will appear stating Your computer originally included a Product Recovery program Reinstall the Product Recovery Program Y N Note If the hard disk drive contains any partitions you will not receive this menu go to step 1 4 Enter Y and Service Partition will be created and loaded with D2D files Note If you do not want to create Service Partition press N and then go to step 8 5 Press ENTER at next window to continue Service Partition will be created System will automatically reboot during this precess Recovery process will copy some files to the Service Partition PKUNZIP others Follow prompts you may be prompted to change CDs System will reboot when complete continue to step 6 to install preloaded system Install preloaded system from CD 6 Boot with Recovery CD and boot diskette if required 7 If the hard disk drive is blank a menu will appear stating Your computer originally included a Product Recovery program Reinstall the Product Recovery Program Y N T To install Service Partition go to step 4 To preload hard disk drive without installing Service Partitio
29. a 36L8870 For 3 pin power cords Region P N Australia New Zealand 76H3514 Thailand 76H3516 Italy 76H3530 Denmark 76H3520 European countries 76H3518 India South Africa 76H3522 Israel 76H3532 Switzerland 76H3528 UK Hong Kong 76H3524 ThinkPad TransNote 143 Notices Notices References in this publication to IBM products programs or services do not imply that IBM intends to make these available in all countries in which IBM operates Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used Any functionally equivalent product program or service that does not infringe any of the intellectual property rights of IBM may be used instead of the IBM product program or service The evaluation and verification of operation in conjunction with other products except those expressly designated by IBM are the responsibility of the user IBM may have patents or pending patent applications covering subject matter in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to the IBM Director of Licensing IBM Corporation 500 Columbus Avenue Thornwood NY 10594 U S A Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both IBM ThinkPad Endurimer ThinkScribe FlexFold TrackPoint Flip Touc
30. a FRU 1150 Fan assembly Battery pack 1010 DIMM 1020 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digi pen holder kit 1070 Computer side 1080 Video card 1120 System board and PC card slot assembly 1130 Step Screw quantity Torque H M2 5 x 4 0 mm nylon coated 4 39 2 Ncm 4 kgfcm 106 ThinkPad TransNote Removing and replacing a FRU When installing Remove the protective sheet from the thermal rubber on the fan assembly O We OO E ThinkPad TransNote 107 Removing and replacing a FRU 2010 LCD assembly Battery pack 1010 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 Video card 1120 continued 108 ThinkPad TransNote Removing and replacing a FRU continued 109 ThinkPad TransNote Removing and replacing a FRU continued 110 ThinkPad TransNote Removing and replacing a FRU Torque Screw cap O 39 2 Ncm 4 kgfcm Screw quantity KE E o EF no xo S gt zc Step 111 ThinkPad TransNote Removing and replacing a FRU 2020 LCD front bezel Battery pack 1010 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 Vid
31. ard 1060 Backup battery and sub battery 1070 Digital pen holder kit For a right handed model For a left handed model 1080 Computer side 1090 ThinkScribe digital notepad assembly 1100 Endurimer and system digi cable 1110 Audio card and speaker 1120 Video card 1130 System board and PC card slot assembly 1140 RJ11 45 card and RJ11 45 cable 1150 Fan assembly 2010 LCD assembly 2020 LCD front bezel 2030 LCD panel and Inverter card 2040 LCD cable S 3010 Digital pen y 4010 Changing the orientation ofc a left or right handed model Locations Front view Rear view 35 35 96 38 41 41 44 45 45 46 47 47 48 49 50 50 51 51 51 58 54 56 58 62 67 69 78 75 75 77 79 82 85 86 89 93 103 106 108 2112 145 123 124 124 183 183 184 33 ThinkScribe digital notepad Parts list n Overall LCD FRUs Keyboard Endurimer leather cover replacing kit Miscellaneous parts Optional FRUs Common parts list Tools Lol Power cords system Notices Trademarks 34 ThinkPad TransNote 185 136 136 189 140 140 141 142 143 143 143 144 144 Product overview Product overview This section presents the following product unique information Specifications The following table lists the specifications of the ThinkPad TransNote Feature
32. battery discharges quickly after replacement replace the system board Checking the sub battery Do the following 1 Recharge the sub battery it might have been discharged 2 Power off the computer and unplug the ac adapter from it 3 Remove the aiey pack for the removal procedure 5 Measure the voltage of the sub battery See the following figure Black Wire Voltage V dc Red 6 0 to 9 0 Black Ground Red e If the voltage is correct replace the system board If the voltage is not correct replace the sub battery If the sub battery discharges quickly after replacement replace the system board General descriptions 31 Checkout guide 32 ThinkPad TransNote ThinkPad TransNote Product overview Specifications Status indicators FRU tests Fn key combinations Symptom to FRU index Numeric error codes Error messages Beep symptoms No beep symptoms LCD related symptoms Identifying problems with the FlipTouch display Identifying problems with the ThinkScribe dud notepad deus Intermittent problems Undetermined problems FRU replacement notices Screw notices Retaining serial numbers Restoring the serial number of the system unit Retaining the UUID Removing and replacing a FRU Removing the ThinkPad TransNote 1010 Battery pack 1020 DIMM 1030 Mini PCI adapter d on 1040 Hard disk drive and hard disk drive c cover 1050 Keybo
33. bbe determinare l incendio o l esplosione della batteria stessa Las bater as contienen peque as cantidades de n quel No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo bater as que se encuentren en la lista de piezas al sustituir la bater a La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma 6 ThinkPad TransNote Safety notices Safety notice A N DANGER The lithium battery can cause a fire an explosion or a severe burn Do not recharge it remove its polarized connector disassemble it heat it above 100 C 212 F incinerate it or expose its cell contents to water Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery La pile de sauvegarde contient du lithium Elle pr sente des risques d incendie d explosion ou de br lures graves Ne la rechargez pas ne retirez pas son connecteur polaris et ne la d montez pas Ne l exposez pas une temperature sup rieure 100 C ne la faites pas br ler et n en exposez pas le contenu l eau Mettez la pile au rebut conform ment la r glementation en vigueur Une pile inappropri e risque de prendre feu ou d exploser Die Systembatterie ist eine Lithiumbatterie S
34. bows If your hair is long fasten it Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip approximately 8 centimeters 3 inches from the end Do not wear jewelry chains metal frame eyeglasses or metal fasteners for your clothing Attention Metal objects are good electrical conductors Wear safety glasses when you are hammering drilling soldering cutting wire attaching springs using solvents or working in any other conditions that might be hazardous to your eyes After service reinstall all safety shields guards labels and ground wires Replace any safety device that is worn or defective Reinstall all covers correctly before returning the machine to the customer 12 ThinkPad TransNote Safety information Electrical safety Observe the following rules when working on electrical equipment j Important Use only approved tools and test equipment Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents Many customers have near their equipment rubber floor mats that contain small conductive fibers to decrease electrostatic discharges Do not use this type of mat to protect yourself from electrical shock Find the room emergency power off EPO switch disconnecting switch or electrical outlet If an electrical accident occurs you can then operate the switch or unplug the power c
35. btaining or installing any diskette fixes Customers in Canada should call IBM HelpPC at 800 565 3344 for assistance or download information Strategy for replacing FRUs j X Before replacing parts Make sure that all diskette fixes are installed before replacing any FRUS listed in this manual Use the following strategy to prevent unnecessary FRU replacement and service expense f you are instructed to replace a FRU but the replacement does not correct the problem reinstall the original FRU before you continue Some computers have both a processor board and a System board If you are instructed to replace either the processor board or the system board and replacing one of them does not correct the problem reinstall that board and then replace the other one f an adapter or device consists of more than one FRU any of the FRUs may be the cause of the error Before replacing the adapter or device remove the FRUs one by one to see if the symptoms change Replace only the FRU that changed the symptoms Important service information _ Attention The setup configuration on the computer you are servicing may have been customized Running Automatic Configuration may alter the settings Note the current configuration settings using the View Configuration option then when service has been completed verify that those settings remain in effect Strategy for replacing a hard disk drive Always try t
36. by electrostatic discharge Establish personal grounding by touching a ground point with one hand before touching these units You must use an electrostatic discharge ESD strap P N 6405959 to establish personal grounding ThinkPad TransNote 53 Removing and replacing a FRU Removing the ThinkPad TransNote Note There are two models of the ThinkPad TransNote one is for a right handed person and the other or a left handed person This manual depicts the right handed model but all remove and replace processes remain the same except the one for the pen holder kit Section 1070 Section 4010 depicts the process for changing the orientation of a right handed model to a left handed model by replacing the Endurimer or leather cover The following illustration shows a right handed ThinkPad TransNote The following illustration shows a left handed ThinkPad TransNote 54 ThinkPad TransNote Removing and replacing a FRU Note for FlexFold hinge The external portion of the ThinkPad TransNote cover is made of a Endurimer material This material can be folded in such a way to allow use of the computer or digital notepad without placing either one face down on a surface See the following examples ThinkPad TransNote 55 Removing and replacing a FRU 1010 Battery pack CAUTION If the rechargeable battery pack is incorrectly replaced there is danger of an explosion The battery pack contains a small amount of harmful
37. by referring to the following The following are not covered under warranty LCD panel cracked from the application of excessive force or from being dropped Scratched cosmetic parts Cracked or broken plastic parts broken latches broken pins or broken connectors caused by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of an incompatible card Damage caused by foreign material in the diskette drive Diskette drive damage caused by pressure on the diskette drive cover or by the insertion of a diskette with multiple labels Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten computer password making the computer unusable Sticky keys caused by spilling a liquid onto the keyboard The following symptoms might indicate damage caused by nonwarranted activities Missing parts might be a symptom of unauthorized service or modification e If the spindle of a hard disk drive become noisy it may have been subjected to excessive force or dropped 20 ThinkPad TransNote Related service information Related service information This section provides information about the following Service Web site When the latest maintenance diskette and the system program service diskette are available a notice will be posted on http www pc ibm com partner infotips Using
38. ckup battery System board on Allocation error for device Load Setup Defaults in IBM BIOS Setup Utility data System board UO device IRQ conflict Operating system not found 2 Backup battery 3 System board Failing bits nnnn 1 DIMM 2 System board Invalid system configuration 1 DIMM 2 de Load Setup Defaults in IBM BIOS Setup Utility 2 Backup battery 3 System board 1 Check that the operating system has no failure and is installed correctly 2 Enter IBM BIOS Setup Utility and see whether the hard disk drive and the diskette drive are properly identified Reseat the hard disk drive 4 Reinstall the operating system 5 If the diskette drive is connected and the operating system is located on in the drive replace the diskette drive Hard disk drive 7 System board e o Hibernation error 1 Restore the system configuration to what it was before the computer entered hibernation mode 2 If memory size has been changed re create the hibernation file Fan error Fan 44 ThinkPad TransNote Beep symptoms Symptom to FRU index Symptom or error FRU or action in sequence One beep and a blank unreadable or flashing LCD 1 Reseat the LCD connector 2 LCD assembly 3 External CRT 4 System board One long and two short beeps and a blank or unreadable LCD 1 System board 2 LCD a
39. computer Determine whether the problem has been solved If the problem does not recur reconnect the removed devices one at a time and test the system after each reinstallation Do this until you find the failing FRU If the problem remains replace the following FRUs one at a time do not replace a nondefective FRU a System board b LCD assembly ThinkPad TransNote 49 FRU replacement notices FRU replacement notices This section contains notices related to removing and replacing parts Read this section carefully before replacing any FRU Screw notices Loose screws can cause a reliability problem An IBM ThinkPad computer addresses this problem with special nylon coated screws that have the following characteristics They maintain tight connections They do not easily come loose even with shock or vibration They are harder to tighten They should be used only once Do the following when you service this machine Keep the screw kit for the P N see in your tool bag Always use new screws Use a torque screwdriver if you have one Tighten screws as follows Plastic to plastic Turn an additional 90 degrees after the screw head touches the surface of the plastic part 90 degrees more a Cross section Logic card to plastic Turn an additional 180 degrees after the screw head touches the surface of the logic card 180 degrees more
40. devices Select a grounding system such as those listed below to provide protection that meets the specific service requirement Note The use of a grounding system is desirable but not required to protect against ESD damage Attach the ESD ground clip to any frame ground ground braid or green wire ground Use an ESD common ground or reference point when working on a double insulated or battery operated system You can use coax or connector outside shells on these systems Use the round ground prong of the AC plug on AC operated computers Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function Proper grounding of the electrical outlet can be verified by a certified electrician Laser compliance statement Some IBM Personal Computer models are equipped from the factory with a CD ROM drive or DVD drive CD ROM drives or DVD drives are also sold separately as options The CD ROM drive or DVD drive is a laser product The CD ROM drive or DVD drive is certified in the U S to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations DHHS 21 CFR Subchapter J for Class 1 laser products Elsewhere the drive is certified to conform to the requirements of the International Electrotechnical Commission IEC 825 and CENELEC EN 60 825 for Class 1 laser products 16 ThinkPad TransNote Laser complia
41. digital notepad Intermittent problems Undetermined problems FRU replacement notices Screw notices Retaining serial numbers Removing and replacing a FRU Removing the ThinkPad TransNote 1010 Battery pack P a 47 48 49 50 50 51 58 54 1020 DIMM 1030 Mini PCI adapter 1040 Hard disk drive and hard disk d s cover 1050 Keyboard 1060 Backup battery and sub battery 1070 Digital pen holder kit 1080 Computer side 1090 ThinkScribe digital notepad assembly 1100 Endurimer and system digi cable 1110 Audio card and speaker 1120 Video card 1130 System board and PC card slot assembly 1140 RJ11 45 card and RJ11 45 cable 1150 Fan assembly 2010 LCD assembly 2020 LCD front bezel i 2030 LCD panel and Inverter card 2040 LCD cable eos 3010 Digital pen J 4010 Changing the orientation oe a left or right handed model Locations Front view Rear view ThinkScribe digital notepad Parts list Overall LCD FRUs Keyboard Endurimer leather cover replacing kit Miscellaneous parts Optional FRUs Common parts list Notices iv Trademarks ThinkPad TransNote Introduction Important service information m Important Diskette fixes are customer installable The diskette fixes are posted on the IBM support site http www pc ibm com support Advise customers to contact the PC Company HelpCenter at 800 772 2227 if they need assistance in o
42. drive is powered off The CPU stops To enter standby mode do any of the following Press Fn F4 Close the ThinkPad TransNote computer To prevent the computer from entering standby mode when the computer is closed click Will not suspend even if LCD is closed in the Power Management Properties window Then only the LCD turns off In certain circumstances the computer goes into standby mode automatically f a suspend time has been set on the timer and the user does not do any operation with the keyboard the TrackPoint the hard disk the parallel connector or the diskette drive within the time set If the ac adapter is plugged in 24 ThinkPad TransNote Related service information If the battery indicator blinks orange indicating that the battery power is low Alternatively if Hibernate when battery becomes low has been selected in the Power Management Properties window the computer goes into hibernation mode Note Even if you don t set the low battery alarm the charge indicator lets you know that the battery is low and then the computer enters the power saving mode automatically This default low battery behavior is independent of the operating system so if you have set the low battery alarm the computer may not do what you specified It chooses either your setting or the default setting whichever is appropriate Any one of the following events causes the computer to resume operatio
43. e M2 0 x 3 5 mm nylon coated 4 24 5 Ncm 2 5 kgfcm M2 5 x 4 0 mm nylon coated 1 39 2 Nem 4 kgfcm continued ThinkPad TransNote 99 Removing and replacing a FRU Note When removing or installing the system board and the PC card slot assembly take care not to damage the eject buttons continued 100 ThinkPad TransNote Removing and replacing a FRU ThinkPad TransNote 101 Removing and replacing a FRU When installing Make sure that all of the claws of the base plate are firmly fixed into place and the plate is firmly attached in the plastic base O O O o o D S o e o o WW 102 ThinkPad TransNote Removing and replacing a 1140 RJ11 45 card and RJ11 45 cable Battery pack 1010 DIMM 1020 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 Video card 1120 System board and PC card slot assembly 1130 FRU Step Screw quantity Torque M2 0 x 3 5 mm nylon coated 1 24 5 Ncm 2 5 kgfcm continued ThinkPad TransNote 103 Removing and replacing a FRU 104 ThinkPad TransNote Removing and replacing a FRU Cable routing Route the connector cable as shown in the following figure ThinkPad TransNote 105 Removing and replacing
44. ecksum is not correct 0187 System board EAIA data access error The access to EEPROM has failed 0188 System board Invalid RFID serialization information area or bad CRC2 The EEPROM checksum is not correct 0189 System board Invalid RFID configuration information area The EEPROM checksum is not correct continued ThinkPad TransNote 41 Symptom to FRU index Symptom or error FRU or action in sequence Hard disk error The hard disk is not working 0190 1 Charge the battery pack Critical low battery error 2 Battery pack 0200 1 Reseat the hard disk drive 2 Load Setup Defaults in IBM BIOS Setup Utility 3 Hard disk drive 4 System board 021x Stuck key Keyboard error Run interactive tests of the keyboard and the auxiliary input device 0220 Monitor type error Monitor type does not match the one specified in CMOS Load Setup Defaults in IBM BIOS Setup Utility 0230 Shadow RAM error The shadow RAM failure at offset nnnn System board 0231 System RAM error System RAM failure at offset nnnn 1 DIMM 2 System board 0232 Extended RAM error Extended RAM failure at offset nnnn 1 DIMM 2 System board 0250 System battery error System battery is dead Replace the backup battery and run IBM BIOS Setup Utility to reset the time and date 0251 System CMOS checksum
45. emoving and replacing a FRU When installing do as follows 1 Attach the connector on the bottom side of the inverter card to the LCD cable connector E continued ThinkPad TransNote 119 Removing and replacing a FRU 2 Attach the LCD cable connector to the connector on the bottom side of the LCD panel El and then lay the LCD panel on the rear cover El 3 Align the upper left corner of the LCD panel with the upper left corner of the rear cover l continued 120 ThinkPad TransNote Removing and replacing a FRU 4 Lift the side of the inverter card Bi a little and plug the cable into the connector on the bottom side of the inverter card D Make sure that the other connector which was connected in the installing procedure H is not disconnected when you lift the inverter card When routing the cable do as following figure 000 ThinkPad TransNote 121 Removing and replacing a FRU 5 Tighten the screws H and El 122 ThinkPad TransNote Removing and replacing a FRU 2040 LCD cable Battery pack 1010 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1050 Digital pen holder kit 1080 Computer side 1090 Video card 1130 LCD assembly 2010 LCD front bezel 2020 LCD panel and Inverter card 2030 ThinkPad TransNote 123 Removing and replacing a FRU 3
46. en hervorzurufen Sebbene le batterie di alimentazione siano a basso voltaggio una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione Aunque las bater as principales tienen un voltaje bajo una bater a cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal 10 ThinkPad TransNote Safety notices Safety notice 8 Before removing any FRU power off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any interconnecting cables Avant de retirer une unit remplacable en client le mettez le syst me hors tension d branchez tous les cordons d alimentation des socles de prise de courant retirez la batterie et d connectez tous les cordons d interface Die Stromzufuhr muB abgeschaltet alle Stromkabel aus der Steckdose gezogen der Akku entfernt und alle Verbindungskabel abgenommen sein bevor eine FRU entfernt wird Prima di rimuovere qualsiasi FRU spegnere il sistema scollegare dalle prese elettriche tutti i cavi di alimentazione rimuovere la batteria e poi scollegare i cavi di interconnessione Antes de quitar una FRU apague el sistema desenchufe todos los cables de las tomas de corriente el ctrica quite la bater a y a continuaci n desconecte cualqu
47. eo card 1120 LCD assembly 2010 Step Screw quantity Torque A M2 5 x 4 0 mm nylon coated 4 39 2 Ncm 4 kgfcm continued 112 ThinkPad TransNote Removing and replacing a FRU continued ThinkPad TransNote 113 Removing and replacing a FRU When installing Before tightening the screws make sure that all of the latches are firmly latched 114 ThinkPad TransNote Removing and replacing a FRU 2030 LCD panel and Inverter card Battery pack 1010 Mini PCI adapter 1030 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 Video card 1120 LCD assembly 2010 LCD front bezel 2020 A CAUTION The FlipTouch panel that covers the LCD display is made of glass When removing or replacing the LCD panel take care not to touch the edge of the FlipTouch display glass to avoid personal injury AN continued ThinkPad TransNote 115 Removing and replacing a FRU Step Screw quantity Torque H M2 5 x 4 0 mm nylon coated 4 39 2 Nem 4 kgfcm continued 116 ThinkPad TransNote Removing and replacing a FRU continued ThinkPad TransNote 117 Removing and replacing a FRU Step Screw quantity Torque H M2 5 x 4 0 mm nylon coated 1 39 2 Nem 4 kgfcm 118 ThinkPad TransNote R
48. h TransNote HelpCenter CompactFlash is a trademark of SanDisk Corporation in the United States and other countries Microsoft Windows Windows NT Windows Me and the Windows logo are trademarks of Microsoft Corporation in the United States and or other countries Intel and Pentium are trademarks of Intel Corporation in the Unites States and or other countries For a complete list of Intel trademarks see http www intel com trademarx htm Other company product or service names may be the trademarks or service marks of others 144 ThinkPad TransNote Notices ThinkPad TransNote 145 Part Number 22P2932 Printed in U S A 1P P N 22P2932
49. hard disk if you remember the user HDP If both user HDP and master HDP have been forgotten the password cannot be removed and the hard disk will not be accessible Supervisor password A supervisor password SVP protects the system information stored in the IBM BIOS Setup Utility so that 22 ThinkPad TransNote Related service information without knowing the password nobody can change the configuration of the computer j X Attention If the SVP has been forgotten there is no way to reset it How to remove the power on password To remove a POP that you have forgotten do the following A If SVP is not installed 1 Turn off the computer 2 Remove the battery pack For how to remove the battery pack see bon Battery 3 Remove the backup battery For how to remove the backup battery see Doed 4 Tum on the computer and wait until the POST ends After the POST ends the password prompt does not appear The POP has been removed 5 Reinstall the backup battery and the battery pack B If SVP is installed 1 Turn on the computer by pressing and holding F1 Enter the SVP The IBM BIOS Setup Utility menu appears 3 Select Password using the cursor keys to move down the menu 4 Select Power On Password 5 Enter the SVP at the Enter Current Password field 6 When the Enter New Password field opens leave it blank and press Enter twice 7 Press Enter in the Changes have been saved window
50. hrow it into fire or water or short circuit it Dispose of the battery pack as required by local ordinances or regulations Use only the battery in the appropriate parts listing when replacing the battery pack Use of an incorrect battery can result in ignition or explosion of the battery La batterie contient du nickel Ne la d montez pas ne l exposez ni au feu ni l eau Ne la mettez pas en court circuit Pour la mettre au rebut conformez vous la r glementation en vigueur Lorsque vous remplacez la batterie veillez n utiliser que les mod les cit s dans la liste de pi ces d tach es ad quate En effet une batterie inappropri e risque de prendre feu ou d exploser Akkus enthalten geringe Mengen von Nickel Sie d rfen nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren La batteria contiene piccole quantit di nichel Non smontarla gettarla nel fuoco o nell acqua n cortocircuitarla Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria utilizzare soltanto i tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potre
51. icon Note If the battery pack becomes hot it may not be able to charge Remove it from the computer and leave it at room temperature for a while After it cools down reinstall and recharge it To check the battery pack do the following 1 Power off the computer 2 Remove the battery pack and measure the voltage between battery terminals 1 and 5 See the following figure Terminal Voltage V dc 1 0 to 16 8 5 Ground 3 If the voltage is less than 11 0 V dc the battery pack has been discharged Note Recharging will take at least 3 hours even if the indicator does not turn on If the voltage is still less than 11 0 V dc after recharging replace the battery 4 If the voltage is more than 11 0 V dc measure the resistance between battery terminals 4 and 5 The resistance must be 4 to 30 K0 If the resistance is not correct replace the battery pack If the resistance is correct replace the system board 30 ThinkPad TransNote Checkout guide Checking the backup battery Do the following 1 Power off the computer and unplug the ac adapter from it 4 Measure the voltage of the backup battery See the following figure Wire Voltage V dc lt Red 2 5 to 3 2 Red Black Ground Black If the voltage is correct replace the system board If the voltage is not correct replace the backup battery If the backup
52. ie kann sich entz nden explodieren oder schwere Verbrennungen hervorrufen Batterien dieses Typs d rfen nicht aufgeladen zerlegt ber 100 C erhitzt oder verbrannt werden Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren La batteria di supporto e una batteria al litio e puo incendiarsi esplodere o procurare gravi ustioni Evitare di ricaricarla smontarne il connettore polarizzato smontarla riscaldarla ad una temperatura superiore ai 100 gradi centigradi incendiarla o gettarla in acqua Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa continued Introduction 7 Safety notices Continuation of Safety notice 4 N DANGER La bater a de repuesto es una bater a de litio y puede provocar incendios explosiones o quemaduras graves No la recargue ni quite el conector polarizado ni la desmonte ni caliente por encima de los 100 C 212 F ni la incinere ni exponga el contenido de sus celdas al agua Des chela ta
53. ier cable de conexi n entre dispositivos Introduction 11 Safety information Safety information The following section contains the safety information that you need to be familiar with before servicing an IBM mobile computer General safety Follow these rules to ensure general safety Observe good housekeeping in the area of the machines during and after maintenance When lifting any heavy object 1 Ensure you can stand safely without slipping 2 Distribute the weight of the object equally between your feet 3 Use a slow lifting force Never move suddenly or twist when you attempt to lift 4 Lift by standing or by pushing up with your leg muscles this action removes the strain from the muscles in your back Do not attempt to lift any objects that weigh more than 16 kg 35 Ib or objects that you think are too heavy for you Do not perform any action that causes hazards to the customer or that makes the equipment unsafe Before you start the machine ensure that other service representatives and the customer s personnel are not in a hazardous position Place removed covers and other parts in a safe place away from all personnel while you are servicing the machine Keep your toolcase away from walk areas so that other people will not trip over it Do not wear loose clothing that can be trapped in the moving parts of a machine Make sure that your sleeves are fastened or rolled up above your el
54. isk drive and hard disk drive cover j X Attention Do not drop or apply any shock to the hard disk drive The hard disk drive is sensitive to physical shock Incorrect handling can cause damage and permanent loss of data Before removing the drive have the user make a backup copy of all the information on the drive if possible Never remove the drive while the system is operating or is in suspend mode Battery pack 1010 Note Loosen the screw H but do not remove it continued ThinkPad TransNote 67 Removing and replacing a FRU Note The hard disk is attached to the cover but the cover is a separate FRU When installing Make sure that the label on the hard disk drive faces the bottom side of the computer and that the hard disk connector is firmly connected 68 ThinkPad TransNote Removing and replacing a FRU 1050 Keyboard Battery pack 1010 DIMM 1020 Hard disk drive and hard disk drive cover 1040 SA ES SEA NN Y N Wp MON SW X M MY A Note Loosen the screw H but do not remove it continued 69 ThinkPad TransNote Removing and replacing a FRU continued 70 ThinkPad TransNote Removing and replacing a FRU When installing Make sure that the keyboard connector is firmly attached 71 ThinkPad TransNote Removing and replacing a FRU When installing When installing the keyboard do as
55. l como dispone la normativa local 8 ThinkPad TransNote Safety notices Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands immediately wash the affected areas with water for at least 15 minutes Seek medical care if any symptoms from the fluid are present after washing Si le panneau d affichage cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide rincez les abondamment pendant au moins quinze minutes Consultez un m decin si des sympt mes persistent apr s le lavage Die Leuchtstoffr hre im LCD Bildschirm enth lt Quecksilber Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Der LCD Bildschirm besteht aus Glas und kann zerbrechen wenn er unsachgemaB behandelt wird oder der Computer auf den Boden f llt Wenn der Bildschirm besch digt ist und die darin befindliche Fl ssigkeit in Kontakt mit Haut und Augen ger t sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesp lt und bei Beschwerden anschlieBend ein Arzt aufgesucht werden Nel caso che caso l LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti poi consultare un medico se i sintomi dovessero permanere Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o
56. ling FRU Any such FRUs are listed at the top of the page Remove them in the order in which they are listed 4 Follow the correct sequence in the steps for removing the FRU as indicated in the drawings by the numbers in square callouts 5 When turning a screw to replace a FRU turn it in the direction indicated by the arrow in the drawing 6 When removing the FRU move it in the direction indicated by the arrow in the drawing 7 To put the new FRU in place reverse the removal procedure and follow any notes that pertain to replacement For information about connecting and arranging internal cables see Locations on page 134 8 When replacing a FRU use the correct screw as shown in the procedures CAUTION Before removing any FRU power off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any interconnecting cables CAUTION Do not disassemble the battery pack throw it into fire or water or short circuit it Dispose of the battery pack as required by local ordinances or regulations Attention Before the computer is powered on after FRU replacement make sure all screws springs and other small parts are in place and are not loose inside the computer Verify this by shaking the computer gently and listening for rattling sounds Metallic parts or metal flakes can cause electrical short circuits Attention The system board is sensitive to and can be damaged
57. n press N General descriptions 21 Related service information 8 If a menu appears asking which operating system to install highlight proper operating system and press ENTER 9 Amenu will appear stating Full Recovery Press ENTER to select 10 Enter Y at the three windows which follow 11 Follow prompts to complete Recovery Passwords As many as three passwords may be needed for any ThinkPad computer the power on password POP the hard disk password HDP and the supervisor password SVP Exception If only SVP is installed the password prompt does not appear when the operating system is booted When any of these passwords is used a password prompt appears on the screen whenever the computer is turned on The computer does not start until the password is entered Power on password A power on password POP protects the system from being powered on by an unauthorized person Without knowing the password nobody can start the system Hard disk password There are two hard disk passwords HDPs User HDP for the user Master HDP for the system administrator who can use it to get access to the hard disk even if the user has changed the user HDP Note There are two modes for the HDP User only and Master User You can enter two HDPs when you select Master User j Attention If the master HDP has been forgotten there is no way to delete it But you can still get access to the
58. n from standby mode The Fn key is pressed The ring indicator RI is signaled by a serial device or a PC Card device The power switch is turned on In Windows operating system the Scheduled Tasks setting has priority over the Resume on timer selection in the Power Management Properties window Note The computer does not accept any input immediately after it enters standby mode Wait a few seconds before taking any action to reenter operation mode Hibernation mode In hibernation mode the following occurs The system status RAM VRAM and setup data are stored on the hard disk The system is powered off Any one of the following events causes the computer to enter hibernation mode The Fn F9 keys are pressed The power switch is turned off and the mode is set to Power switch mode Hibernation The timer conditions are satisfied in suspend mode for operating systems other than Windows 98 Acritically low battery condition occurs and the mode is set to Hibernate when battery becomes low When the power is turned on the computer leaves hibernation mode and resumes operation The hibernation file in the boot record on the hard disk drive is read and System status is restored from the hard disk drive General descriptions 25 Checkout guide Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer Note The diagnostic
59. nal monitor IESSE Interactive Tests Hardware Info Utility Quit F1 Help Run Quick Test CPU Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices Memory Test Full Memory Test Quick FlipTouch display ThinkScribe Use the cursor keys and ESC to move in menus Press ENTER to select 4 Run the applicable function test 5 Follow the instructions on the screen If there is a problem PC Doctor shows messages describing it 6 To exit the test select Quit Exit Diag To cancel the test press Esc Notes 1 After executing PC Doctor check the system time date and reset them if needed General descriptions 27 Checkout guide 2 Following test items in the Serial Ports test are FAILED even if these devices are working properly External Loopback test for the FlipTouch display ThinkScribe or Debug Port Registers And Interrupts test for the Debug Port Detecting system information with PC Doctor PC Doctor can detect the following system information Hardware Info System Configuration Memory Contents Physical Disk Drives Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESALCD Info Utility Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log
60. nce statement When a CD ROM drive or DVD drive is installed note the following N CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure O uso de controles ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposic o radiac o NAAA Hts EAT Wii ATA WERE JR Pour viter tout risque d exposition au rayon laser respectez les consignes de r glage et d utilisation des commandes ainsi que les proc dures d crites Werden Steuer und Einstellelemente anders als hier festgesetzt verwendet kann gefahrliche Laserstrahlung auftreten Az itt el rt elj r sokt l be llitasokt l s vez rl sekt l elt rni a l zersug rz s vesz lye miatt kock zatos L utilizzo di controlli regolazioni o l esecuzione di procedure diverse da quelle specificate possono provocare l esposizione a Mcnonb30BaHne 9NeMeHTOB HACTpPO KN N BbITIO IHeHMe NpOLEAYP UHbIX HEM yka3aHo 3necb MOXKeT MPUBECTH K ONACHOMY paanaunoHHomy oOnyyeHnio Pouzitie kontr l prav alebo inych vykonani od inych vyrobcov ako je v tomto Specifikovan mohlo by mat za n sledok nebezpe enstvo vystavenia sa vyZiarovaniu El uso de controles o ajustes o la ejecuci n de procedimientos distintos de los aqu especificados puede provocar la exposici n a radiaciones peligrosas Opening
61. nostics and select FlipTouch display if the test fails one or both of the following are defective LCD panel 10 4 in TFT with touch panel 05K9623 LCD cable 27L0544 Run Interactive Tests and select FlipTouch display If one or more the positions were not detected properly one or both of the following are defective LCD panel 10 4 in TFT with touch panel 05K9623 LCD cable 27L0544 Identifying problems with the ThinkScribe digital notepad To analyze a problem with the ThinkScribe digital notepad do the following 1 Make sure that the ThinkScribe digital notepad is enabled IBM BIOS Setup Utility gt Config gt ThinkScribe Insert the PC Doctor DOS disk in the diskette drive and turn on the system unit For details on using PC Doctor see While PC Doctor DOS is starting up turn the ThinkScribe digital notepad off and on If the error message ThinkScribe not detected is displayed do the following a Turn off the ThinkScribe digital notepad b Start the ThinkScribe POST by doing the following Press and hold the power button on the ThinkScribe digital notepad Push the reset switch on the ThinkScribe digital notepad While continuing to press and hold the power button wait for 20 seconds If no error message appears on the LCD the notepad has passed all the tests of ThinkScribe POST The problem must be one of the following The System Digi cable 27L0556 is not connected
62. o be reused When installing Align the right edge of the base plate tape El to the D part of the base plate as shown in the following figure continued ThinkPad TransNote 83 Removing and replacing a FRU Note for a non English model Before attaching new digitizer onto the Endurimer do the followings 1 Wipe the surface of the digitizer sheet l gently with a dry soft cloth to remove a stain or a dust on it 2 Stick the digitizer label D onto the digitizer sheet 84 ThinkPad TransNote Removing and replacing a FRU 1100 Endurimer and system digi cable Battery pack 1010 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Computer side 1080 ThinkScribe digital notepad assembly 1090 j Notes about the optional leather cover Scratching or discoloration of the leather cover is not covered under warranty When removing and replacing the leather cover be very careful not to scratch the surface of the Endurimer material Do not subject the system digi cable to tension especially at the base of the cables of the connectors shown in figure El Tension could cause the cable to snap Note When replacing the Endurimer or the system digi cable make sure that the black connector of the System digi cable is attached to the computer and the white connector is attached to the digital notepad assembly For the process of changing
63. o run a low level format before replacing a hard disk drive j _ Attention The drive startup sequence in the computer you are servicing may have been changed Be extremely careful during write operations such as copying saving or formatting If you select an incorrect drive data or programs can be overwritten How to use error messages Use the error codes displayed on the screen to diagnose failures If more than one error code is displayed begin the diagnosis with the first error code Whatever causes the first error code may also cause false error codes If no error code is displayed see if the error symptom is listed in the Symptom to FRU Index for the computer you are servicing Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows Diskette Diskette Compatibility drive capacity 3 5 inch 1 0 MB Read and write 2 0 MB Read and write 4 0 MB Not compatible 2 ThinkPad TransNote Safety notices Safety notices multilingual translations In this manual safety notices appear in English with a page number reference to the appropriate translation in this section The safety notices are provided in English French German Italian and Spanish as follows j Safety notice 1 Before the computer is powered on after FRU replacement make sure all screws springs and other small parts are in place and are not left loose inside the comp
64. oblems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect Such as cosmic radiation electrostatic discharge or Software errors FRU replacement should be considered only when a problem recurs When analyzing an intermittent problem do the following 1 Run the diagnostic test for the system board in loop mode at least 10 times 2 If no error is detected do not replace any FRUs 3 If any error is detected replace the FRU shown by the FRU code Rerun the test to verify that no more errors exist 48 ThinkPad TransNote Symptom to FRU index Undetermined problems You are here because the diagnostic tests did not identify which adapter or device failed incorrect devices are installed a short circuit is suspected or the system is inoperative Follow these procedures to isolate the failing FRU Note Do not replace any FRU if the procedures do not identify it as defective Verify that all attached devices are supported by the computer 1 2 3 Oar Check the power system see Power off the computer Visually check each FRU for damage Replace any damaged FRU Remove or disconnect all of the following devices a Non IBM devices b Devices attached to the port replicator c Printer mouse and other external devices d Battery pack e Hard disk drive f External diskette drive g DIMM h CompactFlash card i PC Card Power on the
65. oosen the screw continued 62 ThinkPad TransNote ThinkPad TransNote 63 Removing and replacing a FRU Note The illustration shows the combo card Connector A is for the LAN feature and B is for the modem feature This slot also supports a Mini PCI modem card or a Mini PCI network card Step depends on the card type Disconnect either A B or both 64 ThinkPad TransNote Removing and replacing a FRU When installing Align the contact edge of the combo card or Mini PCI Card with the corresponding socket contact of the computer at an angle of 25 degrees Insert the card into the socket H Pivot the card until it snaps into place H Make sure that the card is firmly fixed in the slot and does not move easily continued ThinkPad TransNote 65 Removing and replacing a FRU Note Be sure that connectors and cables are properly housed in the slot as shown in the following figure Otherwise the card cannot be seated firmly in it After installing the Mini PCI Card attach the black sheet to the card If the sheet does not stick to the slot on the video card just leave it and install the Mini PCI slot cover not to pinch the cable or the black sheet 66 ThinkPad TransNote Removing and replacing a FRU 1040 Hard d
66. ord quickly Do not work alone under hazardous conditions or near equipment that has hazardous voltages Disconnect all power before Performing a mechanical inspection Working near power supplies Removing or installing main units Before you start to work on the machine unplug the power cord If you cannot unplug it ask the customer to power off the wall box that supplies power to the machine and to lock the wall box in the off position f you need to work on a machine that has exposed electrical circuits observe the following precautions Ensure that another person familiar with the power off controls is near you Attention Another person must be there to switch off the power if necessary Use only one hand when working with powered on electrical equipment keep the other hand in your pocket or behind your back Attention An electrical shock can occur only when there is a complete circuit By observing the above rule you may prevent a current from passing through your body When using testers set the controls correctly and use the approved probe leads and accessories for that tester Stand on suitable rubber mats obtained locally if necessary to insulate you from grounds such as metal floor strips and machine frames Observe the special safety precautions when you work with very high voltages these instructions are in the Introduction 13 Safety information safety section
67. ote 129 Removing and replacing a FRU c Tighten the screws and paste the screw caps Screw holes for a left handed model c Screw holes for a right handed model c Screw hole for both models continued 130 ThinkPad TransNote Removing and replacing a FRU 11 Install the digital notepad to the new Endurimer or leather cover doing as follows a Connect the system digi cable to the digital notepad and then paste the digitizer plate El b Paste the new tape Tape for digitizer 2 aligning the r marks on the digitizer base plate continued ThinkPad TransNote 131 Removing and replacing a FRU c Tighten the screws and paste the screw caps Screw holes for a left handed model c Screw holes for a right handed model V XeT ok oo O O Ok 12 Install the digital pen holder kit See Frazd 132 ThinkPad TransNote Locations Locations Front view TrackPoint buttons Latch System status indicators Power switch computer side Mini PCI Card slot Reset switch computer side DIMM slot ThinkPad button FlipTouch control button Mute button Battery pack Battery pack latch TrackPoint buttons Microphone jack Infrared port Built in monaural speaker Built in microphone Stereo line in jack Stereo headphone jack Digital pen ThinkScribe digital notepad see FThinkScribel Diana NOTEDaAd on Dade X
68. pe for digitizer 3 h Digitizer label i A4 spacer j Refill case K Velcro tape Boss cap Copper tape n Digitizer insulation sheet m Cu tape Screw caps pen A Screw caps pen B Screw caps Optional FRUs 64 MB SDRAM SO DIMM 20L0264 128 MB SDRAM SO DIMM 20L0265 256 MB SDRAM SO DIMM 33L3070 AC adapter 56W 2 pin SANKEN 02K6554 AC adapter 72W 2 pin ASTEC 02K6669 AC adapter 56W 3 pin SANKEN 02K6555 AC adapter 72W 3 pin ASTEC 02K6666 Battery pack 02K6686 Port replicator 04P3687 Standard pen 02K5633 Hard disk drive 10 0 GB SSD 08K9508 Hard disk drive 10 0 GB Hitachi 08K9531 Hard disk drive 20 0 GB Jasper 27L3427 Common battery charger 02K6642 Multiple battery charger 02K6718 142 ThinkPad TransNote Common parts list Parts list Tools Triconnector wrap plug 72X8546 PC test card 35G4703 Audio wrap cable 66G5180 Screwdriver kit 95F3598 Torque screwdriver 05K4695 5mm socket wrench 05K4694 Screwdriver 27L8126 External USB FDD Tool kit 27L3452 ThinkPad hardware maintenance diskette version 1 61 Note Download the file from the Web site Power cords system IBM power cords for a specific region are usually available only in that region For 2 pin power cords Region P N Canada Taiwan United States of America 13H5264 Japan 13H5273 Argentin
69. rom the ac adapter does not always indicate a defect Checking operational charging To check operational charging use a discharged battery pack or a battery pack that has less than 50 of the total power remaining when installed in the computer Perform operational charging If the battery status indicator or icon does not turn on remove the battery pack and let it return to room temperature Reinstall the battery pack If the charge indicator or icon still does not turn on replace the battery pack If the charge indicator still does not turn on replace the System board Then reinstall the battery pack If the reinstalled battery pack has not been charged go to the next section General descriptions 29 Checkout guide Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95 of the total power remains under this condition the battery pack can charge to 100 of its capacity This protects the battery pack from being overcharged or from having a shortened life To ensure a maximum battery charge continue charging the battery for about 30 minutes after the charge indicator reaches 100 To check the status of your battery move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment but do not click and the percentage of battery power remaining is displayed To get detailed information about the battery double click the Power Meter
70. s of maintenance information Use extreme care when measuring high voltages Regularly inspect and maintain your electrical hand tools for safe operational condition Do not use worn or broken tools and testers Never assume that power has been disconnected from a circuit First check that it has been powered off Always look carefully for possible hazards in your work area Examples of these hazards are moist floors nongrounded power extension cables power surges and missing safety grounds Do not touch live electrical circuits with the reflective surface of a plastic dental mirror The surface is conductive such touching can cause personal injury and machine damage Do not service the following parts with the power on when they are removed from their normal operating places in a machine Power supply units Pumps Blowers and fans Motor generators and similar units This practice ensures correct grounding of the units f an electrical accident occurs Use caution do not become a victim yourself Switch off power Send another person to get medical aid Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions As each machine was designed and built required safety items were installed to protect users and service personnel from injury This guide addresses only those items You should use good judgment to identify
71. ssembly 3 DIMM Two short beeps with error codes System board Two short beeps with blank 1 screen 2 DIMM Three short beeps pause 1 DIMM three more short beeps and one short beep 2 System board Only cursor appears Reinstall operating system No beep symptoms Symptom or error FRU or action in sequence No beep power on indicator on LCD blank and no POST 1 Make sure that every connector is connected tightly and correctly DIMM System board on No beep power on indicator on and LCD blank during POST ak Reseat DIMM System board N No beep during POST but system runs correctly Speaker connection or speaker The power on password prompt A power on password or a supervisor password is set Type the password and press Enter The hard disk password prompt A hard disk password is set Type the password and press Enter The DOS full screen looks smaller Start the ThinkPad Configuration program and set the Screen expansion function ThinkPad TransNote 45 Symptom to FRU index LCD related symptoms j Important The TFT LCD for the notebook computer contains many thin film transistors TFTs A small number of dots that are missing discolored or always lighted is characteristic of TFT LCD technology but excessive pixel problems can cause viewing concerns The LCD should be replaced
72. stema y escuchando los posibles ruidos que provocar an Las piezas met licas pueden causar cortocircuitos el ctricos Introduction 3 Safety notices Safety notice 2 N DANGER Some standby batteries contain a small amount of nickel and cadmium Do not disassemble a standby battery recharge it throw it into fire or water or short circuit it Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery Certaines batteries de secours contiennent du nickel et du cadmium Ne les d montez pas ne les rechargez pas ne les exposez ni au feu ni l eau Ne les mettez pas en court circuit Pour les mettre au rebut conformez vous la r glementation en vigueur Lorsque vous remplacez la pile de sauvegarde ou celle de l horloge temps r el veillez n utiliser que les mod les cit s dans la liste de pi ces d tach es ad quate Une batterie ou une pile inappropri e risque de prendre feu ou d exploser Die Bereitschaftsbatterie die sich unter dem Diskettenlaufwerk befindet kann geringe Mengen Nickel und Cadmium enthalten Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden Sie darf nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Die Batterie kann schwere Verbrennungen oder Ver tzungen ver
73. sus manos lave inmediatamente las reas afectadas con agua durante 15 minutos como m nimo Obtenga atenci n medica si se presenta alg n s ntoma del fluido despues de lavarse Introduction 9 Safety notices Safety notice 6 To avoid shock do not remove the plastic cover that protects the lower part of the inverter card Afin d viter tout risque de choc lectrique ne retirez pas le cache en plastique prot geant la partie inf rieure de la carte d alimentation Aus Sicherheitsgr nden die Kunststoffabdeckung die den unteren Teil der Spannungswandlerplatine umgibt nicht entfernen Per evitare scosse elettriche non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore Para evitar descargas no quite la cubierta de pl stico que rodea la parte baja de la tarjeta invertida j Safety notice 7 Though the main batteries have low voltage a shorted or grounded battery can produce enough current to burn personnel or combustible materials Bien que le voltage des batteries principales soit peu lev le court circuit ou la mise la masse d une batterie peut produire suffisamment de courant pour br ler des mat riaux combustibles ou causer des br lures corporelles graves Obwohl Hauptbatterien eine niedrige Spannung haben k nnen sie doch bei KurzschluB oder Erdung genug Strom abgeben um brennbare Materialien zu entz nden oder Verletzungen bei Person
74. symptom is not a hardware problem No service action is necessary if the pointer stops after a short time If enabling the TrackPoint does not correct the problem continue with the following Interactive Tests gt Mouse continued 38 ThinkPad TransNote Product overview FRU Applicable test Hard disk Diagnostics gt Fixed Disks drive Diskette drive 1 Interactive Tests gt CD ROM DVDDiskette Drives 2 Interactive Tests gt Diskette CD ROM or Interactive Tests gt CD ROM DVD DVD drive Memory 1 Run Memory Test Quick 2 If the test does not detect the error run Diagnostics gt Memory Test Full Fan 1 Turn on the computer and check the air turbulence at the louver of the rear side 2 Run Diagnostics gt Other Devices gt IBM Fan FlipTouch display ThinkScribe digital notepad Fn key combinations The following table shows the function of each combination of Fn with a function key The Fn key works independently from the operating system Key combination Description Fn F3 Turn off the computer display leaving the screen blank To turn the computer display on again press any key or the TrackPoint pointer Also the computer display is turned on if the ac adapter is attached to or detached from the computer Fn F4 Put the computer in standby mode To return to normal operation press the Fn key
75. t be powered on go to EPowel eiai ea a page A and chek ho Power sources If an error code appears go to ESymptom to FRUI noex on page 4 On the first screen select the model and press Enter Follow the instructions on the screen 2 The main panel of PC Doctor appears 26 ThinkPad TransNote Checkout guide 3 Select Diagnostics with the arrow keys and press Enter A pull down menu appears Its exact form depends on the model The options on the test menu are as follows Diagnostics Interactive Tests Run Normal Test Keyboard Run Quick Test Video CPU Coprocessor Internal Speaker Systemboard Mouse Video Adapter Joystick Test Serial Ports Diskette Parallel Ports System Load Fixed Disks CD ROM DVD Test Diskette Drives Stereo Speaker Other Devices ThinkScribe LCD Test Memory Test Full ThinkScribe LED Test Memory Test Quick ThinkScribe Interactive Test FlipTouch Display FlipTouch Display ThinkScribe Notes n the Keyboard test in Interactive Tests the Fn key is scanned only once Each key should be held down for at least 2 seconds otherwise it cannot be sensed Sound Card is not recognized in the Stereo Speaker in the Interactive Tests To test it use the audio device test in the Other Devices Diagnostics Video Adapter test supports only the LCD display on ThinkPad TransNote Before running PC Doctor DOS detach the exter
76. the CD ROM drive or DVD drive could result in exposure to hazardous laser radiation There are no serviceable parts inside the CD ROM drive or DVD drive Do not open Introduction 17 Laser compliance statement Some CD ROM drives or DVD drives contain an embedded Class 3A or Class 3B laser diode Note the following N DANGER Emits visible and invisible laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam Radiac o por raio laser ao abrir Nao olhe fixo no feixe de luz n o olhe diretamente por meio de instrumentos ticos e evite exposic o direta com o feixe de luz FAN SABO EDITADO gt Z EIS FARE BeBe ZER ZF o Rayonnement laser si carter ouvert Evitez de fixer le faisceau de le regarder directement avec des instruments optiques ou de vous exposer au rayon Laserstrahlung bei ge ffnetem Ger t Nicht direkt oder ber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden Kinyit skor l zersug r Ne n zzen bele se szabad szemmel se optikai eszk z kkel Ker lje a sug rnyal bbal val rintkez st Aprendo l unit vengono emesse radiazioni laser Non fissare il fascio non guardarlo direttamente con strumenti ottici e evitare l esposizione diretta al fascio OrkpbiBas Geperurecb NasepHoro usnyyeHua He cmoTpuTe Ha nyy He pasrnsvgpipalite ero C llOMOLLIBIO ONTUYECKUX UHCTPYM
77. to do with a hardware defect such as cosmic radiation electrostatic discharge or software errors Consider replacing a FRU only when a problem recurs If you suspect that a FRU is defective clear the error log and run the test again If the error does not recur do not replace the FRU Be careful not to replace a nondefective FRU What to do first When you do return a FRU you must include the following information in the parts exchange form or parts return form that you attach to it 1 Name and phone number of servicer 2 Date of service 3 Date on which the machine failed 4 Date of purchase 5 Failure symptoms error codes appearing on the display and beep symptoms 19 Read this first 6 Procedure index and page number in which the failing FRU was detected 7 Failing FRU name and part number 8 Machine type model number and serial number 9 Customer s name and address Note for warranty During the warranty period the customer may be responsible for repair costs if the computer damage was caused by misuse accident modification unsuitable physical or operating environment or improper maintenance by the customer The following list provides some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use Before checking problems with the computer determine whether the damage is covered under the warranty
78. unction as pressing the numeric lock key Fn 4 Page up Fn y Page down Fn e Gives the same function as pressing the home key Fn gt Gives the same function as pressing the end key Fn Gives the same function as pressing the break key Fn Left shift Gives the same function as pressing the caps lock key 40 ThinkPad TransNote Symptom to FRU index Symptom to FRU index The symptom to FRU index in this section lists symptoms and errors and their possible causes The most likely cause is listed first in boldface type Note Do the FRU replacement or other actions in the sequence shown in the column headed FRU or action in sequence If replacing a FRU does not solve the problem put the original part back in the computer Do not replace a nondefective FRU This index can also help you determine during regular servicing what FRUs are likely to need to be replaced next A numeric error is displayed for each error detected in POST or system operation In the displays n can be any number If no numeric code is displayed check the narrative descriptions of symptoms If the symptom is not described there go to Note For an IBM device not supported by diagnostic codes in the ThinkPad notebook computers see the manual for that device Numeric error codes Symptom or error FRU or action in sequence 0175 System board Bad CRC1 stop POST task The EEPROM ch
79. urns from the standby mode and the standby indicator goes off ThinkPad TransNote 37 FRU tests Product overview The following table shows the test for each FRU FRU Applicable test System board 1 Diagnostics gt CPU Coprocessor 2 Diagnostics gt Systemboard Power Diagnostics gt Other Devices gt IBM AC Adapter IBM Battery 1 LCD unit Diagnostics gt Video Adapter 2 Interactive Tests gt Video Modem Make sure the modem is set up correctly 2 Replace the modem jack and the modem card in turn and run the following tests in Diagnostics gt Other Devices Modem Register Test Modem DTMF Loopback Test Audio Speaker 1 Interactive Tests gt Internal Speaker 2 Diagnostics gt Other Devices gt Crystal SoundFusion Test Interactive Tests gt Internal Speaker PC Card slots Diagnostics gt Systemboard gt PCMCIA PCMCIA External Loop Keyboard 1 Diagnostics gt Systemboard gt Keyboard 2 Interactive Test gt Keyboard TrackPoint or pointing device If the TrackPoint does not work check the configuration in the ThinkPad Configuration program If the TrackPoint is disabled select Enable to enable it After you use the TrackPoint the pointer may drift on the screen for a short time This drift can occur when a slight steady pressure is applied to the TrackPoint pointer This
80. ursachen Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Bereitschafts oder Systembatterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren continued 4 ThinkPad TransNote Safety notices Continuation of Safety notice 2 N DANGER Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio Non smontarle ricaricarle gettarle nel fuoco o nell acqua n cortocircuitarle Smaltirle secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria dell RTC real time clock o la batteria di supporto utilizzare soltanto i tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa Algunas bater as de reserva contienen una peque a cantidad de n quel y cadmio No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo bater as que se encuentren en la lista de piezas La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma Introduction 5 Safety notices Safety notice 3 N DANGER The battery pack contains small amounts of nickel Do not disassemble it t
81. uter Verify this by shaking the computer and listening for rattling sounds Metallic parts or metal flakes can cause electrical shorts Avant de remettre l ordinateur sous tension apr s remplacement d une unit en client le v rifiez que tous les ressorts vis et autres pi ces sont bien en place et bien fix es Pour ce faire secouez l unit et assurez vous qu aucun bruit suspect ne se produit Des pi ces m talliques ou des copeaux de m tal pourraient causer un court circuit Bevor nach einem FRU Austausch der Computer wieder angeschlossen wird muf sichergestellt werden daB keine Schrauben Federn oder andere Kleinteile fehlen oder im Gehause vergessen wurden Der Computer mu gesch ttelt und auf Klappergerausche gepr ft werden Metallteile oder splitter k nnen Kurzschl sse erzeugen Prima di accendere l elaboratore dopo che stata effettuata la sostituzione di una FRU accertarsi che tutte le viti le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse all interno dell elaboratore Verificare ci scuotendo l elaboratore e prestando attenzione ad eventuali rumori eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi Antes de encender el sistema despues de sustituir una FRU compruebe que todos los tornillos muelles y dem s piezas pequefias se encuentran en su sitio y no se encuentran sueltas dentro del sistema Compru belo agitando el si
82. ving and replacing a FRU 1080 Computer side Battery pack 1010 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Screw removal notice When removing the computer side from the Endurimer or leather cover remove only the screws marked with gt beside the screw holes Step Screw quantity Screw cap Torque M2 5 x 3 mm none 39 2 Nom nylon coated 1 4 kgfcm M2 5 x 3 mm Ki 39 2 Nom nylon coated 3 4 kgfcm A M2 5 x 4 5 mm 39 2 Ncm nylon coated 1 4 kgfcm continued ThinkPad TransNote 79 Removing and replacing a FRU continued 80 ThinkPad TransNote Removing and replacing a FRU ThinkPad TransNote 81 Removing and replacing a FRU 1090 ThinkScribe digital notepad assembly Battery pack 1010 Hard disk drive and hard disk drive cover 1040 Digital pen holder kit 1070 Screw removal notice When removing the computer side from the Endurimer or leather cover remove only the screws marked with gt beside the screw holes Step Screw quantity Screw cap Torque H M2 5 x 3 mm Es 39 2 Nom nylon coated 3 4 kgfcm E M2 5 x 3 mm none 39 2 Nem nylon coated 2 4 kgfcm continued 82 ThinkPad TransNote Removing and replacing a FRU Note In procedure E remove the base plate tape gently in the direction of the arrow to avoid damaging the copper sheet under the tape it is t

Download Pdf Manuals

Related Search

Related Contents

13 eagle eye gold catéter para ecografía intravascular  に ノ ・重 - のミサト株式会社  INSTRUCTION AND MAINTENANCE HANDBOOK arv TANARG 912  eva anglais cm2 cahier eleve mai 2012.pub  ERC/ERC-Z 12/14/16    Allgemeine Gerätefunktions - GEP  Sagiblue - Active Audio  Tender No: TCIL/15/1597/I/14-MM/16E Issued on: July 15, 2014  

Copyright © All rights reserved. Failed to retrieve file