i. Tech Dynamic Clip V User's Manual
Contents
1. Y TecH Bluetooth 2005 Hutchison Harbour Ring Enterprises Limited All rights in this publication are reserved and no part may be reproduced without the prior written permission of the publisher The contents of this publication are believed to be correct at the time of going to press but any information specifications products or services mentioned may be modified supplemented or withdrawn without further notice The Stylized i Tech logos are trademarks owned by Hutchison Harbour Ring Enterprises Limited or its affiliates Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG Inc USA and licensed to i Tech Dynamic Limited www itechdynamic com Printed in China fo CE FE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment i Tech declares under our sole responsibility that the headset is in conformity with the provisions of the following Council Directives 1999 5 EC a Dispose of the packaging and this product in mmm accordance with the latest provisions 01 2006 PIN S3J 51A05054 03 Sf Teck i Tech Clip V User2. Guide ENGLISH Table of Contents i Tech Clip V Overview Getting Started Charging Your Headset Charging Time Talk and Stand by Time Low Battery Turning your Headse Pairing Your Headset Using Your Headset Answering a Call Ending a Call Dialing from Y Muting the Built in Buzzer Muting the Microphone w Voice Dialing from Your Headset Last Number Redialing from Your Headset Rejecting a Call Handsfree Profile ONLY Transferring a Call Handsfree Profile ONLY Adjusting the Volume Resetting the Headset Care and Maintenance Built in Battery Charger Safety Information Troubleshooting Product Specifications Declaration of Conformity D00 ENGLISH Do SON ah i Tech Clip V Overview Microphone Volume Key Status Indicator Built in Buzzer Charging Socket Built in Rechargeable Battery Multi function Button MFB Earphone Getting Started To use your i Tech Clip V the headset please follow these simple steps Charge your headset Pair your headset with a Bluetooth enabled mobile handset ENGLISH Charging Your Headset i Charging Your Headset Connect the charger to an AC wall outlet mains socket and the charger plug to the headset s charging socket fig 1 The LED will be red while charging IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long time
3. ing the Built in Buzzer Press and hold the volume key for two seconds until status indicator flashes RED once to mute the Buzzer and press and hold the volume key for 3 seconds to deactiveate the muting function while your mobile phone remains in Standby mode IMPORTANT If you do not wish to be disturbed at all you may consider resetting the mobile phone setting to restrict incoming calls Please refer to your mobile phone user guide for set up details ae 2 zi O z wW ENGLISH Using Your Headset Muting the Microphone You can put a call on hold by muting the microphone Press and hold the volume key for two seconds until status indicator flashes Red to mute built in Microphone and press and hold the volume key for 3 seconds to deactivate the muting function while conversation Voice Dialling from Your Headset If your mobile handset is equipped with a voice dialling function simply press the MFB on your headset and when you hear a beep say the voice tag IMPORTANT Please make sure voice tag into the mobile handset first before using voice dialling function as 2 0 Zz Ww Last Number Redialling from Your Headset Short press the MFB on your headset twice IMPORTANT The above functions are only applicable to mobile handsets with Bluetooth Handsfree Profile Functionality varies depending on the mobile handset model you have Please refer to your mobile handset user guide for additional information Rejec
4. mely high or low temperatures Do not dispose of the headset in a fire as it will result in explosion Do not expose your headset to contact with sharp objects as this will cause scratches and damage Do not stick anything inside the headset as this may damage internal components Do not attempt to disassemble the headset as it does not comtain serviceable components If you do not use the headset for long periods be sure to store it in a dry place free from extreme tempera tures and dust ENGLISH Built in Battery e Do not attempt to replace the headset s battery yourself as it is built into the headset and is not changeable e Charge the battery in accordance with the instruction supplied with this user guide Only use the manufacturer supplied charger when charging the headset charger e Only use the manufacturer supplied charger when charging the headset Do not disassemble the charger as it may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the headset is subsequently used e Do not use the charger outdoors or in damp areas e Only charge the headset s built in battery in accordance with the instructuins in this user guide e Avoid charging the headset in extremely high or low temperatures Safety Information Check local laws regarding use of a mobile handset and headset whilst driving If you use the headset while driving ensure your attenti
5. mobile handset user guide for details 5 Set the mobile handset to search for Bluetooth devices within 1 meter range as instructed in the mobile handset user guide and select i Tech Clip V from the list 6 Enter the preprogrammed passkey 0000 and press OK to pair your headset and mobile handset when the pairing is complete the headset status indicator will flash blue rapidly 5 times followed by a long beep ENGLISH 7 Press Return to go back to your mobile handset s main menu For certain mobile handset models a headset icon will be shown on the screen You should now be able to make and receive calls using your headset IMPORTANT If the pairing cannot be completed within 2 minutes while the pairing mode is activated the headset Status indicator flashes purple followed by 3 beeps and the headset is turned off Please repeat the above pairing procedures Using Your Headset Answering a Call When there is an incoming call you will hear ringing through the earphone and the built in buzzer Press the MFB to accept the call or answer the call via your mobile handset in the normal way IMPORTANT ou can stop the buzzer alert by pressing the volume key once The buzzer will ring again when there is another incoming call Ending a Call Press the MFB to end your call or end the call via your mobile handset in the normal way Dialing from Your Mobile Handset Simply make calls on your mobile handset in the normal way Mut
6. o that the connection between the headset and the mobile handset is resumed For pairing please refer to Pairing Your Headset on page 7 8 Turning Your Headset On and Off ab 2 ai 0 Zz Ww Turning Off the Headset Press and hold the MFB for approximately 3 seconds until you hear a long beep The status indicator will stop flashing IMPORTANT To disconnect the Bluetooth connection press the MFB firmly to turn off your headset If you will not be using the headset for a while you should consider turning off the Bluetooth function on your mobile phone as well Pairing Your Headset The headset only works with Bluetooth enabled mobile phones Prior to using and pairing your headset for the first time please check if your mobile phone is Bluetooth enabled The pairing instructions for a typical Bluetooth enabled mobile phone are explained on the next page The headset pairing procedure may vary depending on the model of your mobile phone Please contact the manufacturer of your mobile phone or its agent for further information Up to 1 metre lt gt Pairing Your Headset 1 Place the headset and the mobile handset no more then 1 meter apart and ensure there is nothing in between 2 Ensure the headset is OFF 3 Press and hold the MFB approximately 8 seconds until the headset status indicator alternately flashes blue and red 4 Activate your mobile handset s Bluetooth function by referring to your
7. on and focus remain on the road and you drive in a responsible and safe manner Never allow children to play with the headset small parts may be a choking hazard Observe all signs that require an electrical device or RF radio product to be switched off in designated areas These could include hospitals blasting areas and potentially explosive environments Turn off your headset prior to boarding an aircraft Do not use your headset in an aircraft Never mount or store your headset over any air bag deployment area as serious injury may result when an air bag deploys Do not open or mutilate the built in battery Dispose of batteries according to local regulations Do not dispose as household waste Dispose of the packaging and this product in accordance with the latest provisions Declaration of Conformity DoC Product Specifications ENGLISH ENGLISH We i Tech Dynamic Ltd declare that the following product Bluetooth Specification Version 1 2 Class 2 Product Name i Tech Clip V Model No C51 A05054 XX Headset and Handsfree 2 4GHz Spectrum up to 6 hours Bluetooth Profile Supported Range of Frequency Talk Time Standby Time Nominal charging Time Within 3 hours 46 L X 18 W x 22 5 H mm May vary due to users operation Weight 16 7 grams mode and mobile phone settings Is in conformity with the following essential requirements of Council Directive 1999 5 EC refe
8. or the battery is drained ae v i 0 z Ww Charging Time Charging the battery fully is normally within 3 hours when the battery is fully charged the LED will turn blue and remain on Disconnect the charger from AC wall outlet mains socket and the headset Press and hold the MFB fig 1 for 2 seconds to turn the headset on please refer to Turning Your Headset On and Off Talk amp Standby Time Charger Plug The fully charged battery offers up to 6 hours talk time and up to 120 hours standby time When no calls are in progress the headset remains turned on in standby mode The Headset comes with a built in rechargeable battery Prior to using the headset it is recommendable to charge the battery fully for the first time Charging Socket P Charger fig 1 N fig 2 ENGLISH Low Battery when the headset is on and the battery becomes low the status indicator flashes red and the headset emits a beep every 1 minute Please recharge the battery as described above If you are setting up the headset and your mobile phone in a noisy environment we advise you to put on the earphone first so that the beep will be more audible Turning Your Headset On and Off Turning On the Headset Press and hold the MFB for 2 seconds until you hear a short beep The status indicator will then flash blue IMPORTANT Press the MFB again after the headset switched on each time you turn on the headset to reactivate pairing s
9. rred to as R amp TTE Directive Article 3 1a 3 1 D and 3 2 and the product is manufactured in accordance with Annex II of above directive up to 120 hours A copy of the Declaration of Conformity can be found at http Awww itechdynamic com Dimensions
10. ting a Call Handsfree Profile ONLY Press and hold the volume key then press and hold the MFB until the incoming call is rejected Transferring a Call Handsfree Profile ONLY Press and hold the volume then press and hold the MFB until the audio is transferred from headset to your mobile handset during conversation ENGLISH Adjusting the Volume Press the Volume Key repeatedly until you reach the desired volume level The listening volume may be affected by the volume setting of the caller s phone as well Re adjust the listening volume again when necessary Resetting the Headset You may reset the headset to its original settings at anytime in doing this you also clear all current pairing settings 1 Ensure the headset is OFF 2 Press and hold the volume key for 20 seconds until the status indicator flashes Red and Blue 3 Release the Volume Key 4 Press and hold the Volume Key again until you hear 2 beeps 5 Recharge the headset for a few seconds The headset is turned off and returns to the original settings All current pairings are cleared Care and Maintenance Headset e Consider turning your headset off before placing it in your pocket or bag If the MFB is accidentally depressed your mobile handset may place an unintended call Do not expose the headset to liquid moisture or humidity as it is not waterproof e Do not use abrasive cleaning solvents to clean the headset Do not expose the headset to extre
Download Pdf Manuals
Related Search