Home

Husqvarna T435 User's Manual

1. T e Keep the chain properly tensioned If the chain is slack it is more likely to jump off and lead to increased wear on the bar chain and drive sprocket e Keep cutting equipment well lubricated and properly maintained A poorly lubricated chain is more likely to break and lead to increased wear on the bar chain and drive sprocket 4 GENERAL SAFETY PRECAUTIONS Cutting equipment designed to reduce kickback WARNING Faulty cutting equipment or the wrong combination of bar and saw chain increases the risk of kickback Only use the bar saw chain combinations we recommend and follow the filing instructions See instructions under the heading Technical data The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything By using cutting equipment with built in kickback reduction and keeping the chain sharp and well maintained you can reduce the effects of kickback Bar The smaller the tip radius the lower the chance of kickback Chain A chain is made up of a number of links which are available in standard and low kickback versions IMPORTANT No saw chain design eliminates the danger of kickback WARNING Any contact with a rotating saw chain can cause extremely serious injuries Some terms that describe the bar and chain To maintain the safety features of the cutting equipment you should replace a worn or damaged bar or chain with a bar and chain c
2. Chain oil e We recommend the use of special oil chain oil with good adhesion characteristics e Never use waste oil This results in damage to the oil pump the bar and the chain e Itis important to use oil of the right grade suitable viscosity range to suit the air temperature e Intemperatures below 0 C 32 F some oils become too viscous This can overload the oil pump and result in damage to the oil pump components e Contact your service agent when choosing chain oil English 17 FUEL HANDLING Fuelling WARNING Taking the following precautions will lessen the risk of fire Do not smoke and do not place any hot objects in the vicinity of fuel Always stop the engine and let it cool for a few minutes before refuelling When refuelling open the fuel cap slowly so that any excess pressure is released gently Tighten the fuel cap carefully after refuelling Always move the machine away from the refuelling area before starting Clean the area around the fuel cap Clean the fuel and chain oil tanks regularly The fuel filter must be replaced at least once a year Contamination in the tanks causes malfunction Make sure the fuel is well mixed by shaking the container before refuelling The capacities of the chain oil tank and fuel tank are carefully matched You should therefore always fill the chain oil tank and fuel tank at the same time WARNING Fuel and fuel vapour are highly flammable Ta
3. Aspen two stroke fuel or environmental fuel for four stroke engines blended with two stroke oil as set out below Note that carburettor adjustment may be necessary when changing the type of fuel see the instructions under the heading Carburettor Running in Avoid running at a too high speed for extended periods during the first 10 hours Two stroke oil e For best results and performance use HUSQVARNA two stroke engine oil which is specially formulated for our air cooled two stroke engines e Never use two stroke oil intended for water cooled engines sometimes referred to as outboard oil rated TCW e Never use oil intended for four stroke engines e A poor oil quality and or too high oil fuel ratio may jeopardise function and decrease the life time of catalytic converters Mixing ratio 1 50 2 with HUSQVARNA two stroke oil or JASO FC or ISO EGC GRADE 1 33 3 with oils class JASO FB or ISO EGB formulated for air cooled two stroke engines e Always mix the petrol and oil in a clean container intended for fuel e Always start by filling half the amount of the petrol to be used Then add the entire amount of oil Mix shake the fuel mixture Add the remaining amount of petrol e Mix shake the fuel mixture thoroughly before filling the machine s fuel tank e Do not mix more than one month s supply of fuel at a time e ifthe machine is not used for some time the fuel tank should be emptied and cleaned
4. medication or anything that could affect your vision alertness coordination or judgement Wear personal protective equipment See instructions under the heading Personal protective equipment Do not modify this product or use it if it appears to have been modified by others Never use a machine that is faulty Carry out the checks maintenance and service instructions described in this manual Some maintenance and service measures must be carried out by trained and qualified specialists See instructions under the heading Maintenance Never use any accessories other than those recommended in this manual See instructions under the headings Cutting equipment and Technical data CAUTION Always wear protective glasses or a face visor to reduce the risk of injury from thrown objects A chain saw is capable of throwing objects such as wood chips small pieces of wood etc at great force This can result in serious injury especially to the eyes WARNING Running an engine ina confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning WARNING Faulty cutting equipment or the wrong combination of bar and saw chain increases the risk of kickback Only use the bar saw chain combinations we recommend and follow the filing instructions See instructions under the heading Technical data Always use common sense It is not possible to cover every conceivable situation you can face wh
5. s manual 2 English Working position i RUN Choke l IN CHOKE Other symbols decals on the machine refer to special certification requirements for certain markets Symbols in the operator s manual Switch off the engine before carrying out any checks or maintenance EJ Qe Always wear approved protective gloves Regular cleaning is required Visual check se ES Protective goggles or a visor must be worn Refuelling Filling with oil and adjusting oil flow The chain brake must be engaged when the chain saw is started WARNING Kickback may occur when the nose or tip of the guide bar touches an object and cause a lightning fast reverse reaction kicking the guide bar up and towards the operator May cause serious personal injury EN CY CONTENTS Contents KEYTO SYMBOLS Symbols on the machine u 2 Symbols in the operators manual 2 CONTENTS Contents PP enter a 3 INTRODUCTION Dear Customer 2 4 WHAT IS WHAT What is what on the chain Saw 5 GENERAL SAFETY PRECAUTIONS Before using a new chain Saw 0esseeeeeeeeees 6 ImB rtanl pitt 6 Always use COMMON SENSE ccceeeeeeeeeeeeeeeeeeees 6 Personal protective equipment 6 eee 7 Machine s safety equipment s 7 Cutting equipment une 10 ASSEMBLY Fitting the bar and chalka ueasnne 16 FUEL HANDLING A A 17 Fueling uta coi 1
6. spark plug should be replaced after about a month in operation or earlier if necessary Note Always use the recommended spark plug type Use of the wrong spark plug can damage the piston cylinder Check that the spark plug is fitted with a suppressor Lubricating the bar tip sprocket Lubricate the bar tip sprocket each time you refuel Use the special grease gun and a good quality bearing grease MAINTENANCE Adjustment of the oil pump The oil pump is adjustable Adjustments are made by turning the screw with a screwdriver Turning the screw clockwise will increase the oil flow turning it anticlockwise will reduce the oil flow The oil tank should become nearly empty by time fuel is used up Be sure to refill the oil tank every time when refueling the saw WARNING The engine must not be running when making adjustments Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system The cooling system consists of 1 Air intake on the starter Air guide plate Fins on the flywheel Cooling fins on the cylinder O A O N Clutch cover Clean the cooling system with a brush once a week more often in demanding conditions A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder English 35 MAINTENANCE Maintenance schedule The following is a list of the maintenance that
7. a little at full throttle It is also important that the chain does not rotate at idle If the L jet is set too lean it may cause starting difficulties and poor acceleration If the H jet is set too lean the machine will have less power poor acceleration and could suffer damage to the engine Checking maintaining and servicing chain saw safety equipment Note All service and repair work on the machine demands special training This is especially true of the machine s safety equipment If your machine fails any of the checks described below we recommend that you take it to your service workshop Chain brake and front hand guard Checking brake band wear Brush off any wood dust resin and dirt from the chain brake and clutch drum Dirt and wear can impair operation of the brake Regularly check that the brake band is at least 0 6 mm thick at its thinnest point 30 English Checking the front hand guard Make sure the front hand guard is not damaged and that there are no visible defects such as cracks Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover Checking the brake trigger Place the chain saw on firm ground and start it Make sure the chain does not touch the ground or any other object See the instructions under the heading Start and stop Grasp the chain saw firmly wrapping your fingers and thumbs around the
8. be filed down to achieve the recommended depth gauge setting See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain See instructions under the heading Technical data for information about sharpening your chain WARNING Departure from the A y sharpening instructions considerably Al C increases the risk of kickback B WARNING The risk of kickback is increased if the depth gauge setting is too large 12 English GENERAL SAFETY PRECAUTIONS Adjustment of depth gauge setting e The cutting teeth should be newly sharpened before adjusting the depth gauge setting We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth NOTE This recommendation assumes that the length of the cutting teeth is not reduced excessively e You will need a flat file and a depth gauge tool We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge e Place the depth gauge tool over the chain Detailed information regarding the use of the depth gauge tool will be found on the package for the depth gauge tool Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool A Tensioning the chain WARNING A
9. during tree service operations shows the primary cause as being inappropriate one handed use of the saw In the vast majority of accidents operators fail to adopt a secure work position witch allows them to hold both handles of the saw This results in an increased risk of injury due to e not having a firm grip on the saw if it kicks back English 23 WORKING TECHNIQUES e alack of control of the saw such that it is more liable to contact climbing lines and operators body particularly the left hand and arm e loosing control from insecure work position resulting in contact with the saw unexpected movement during operation of the saw Securing the work position for two handed use To allow the operator to hold the saw with both hands they should as general rule aim for secure work position where they are operating the saw at e hip level when cutting horizontal sections e solar plexus level when cutting vertical sections Where the operator is working close into vertical stems with a low lateral forces on their work position then a good footing may be all that is needed to maintain a secure work position However as operators move away from the stem they will need to take steps to remove or counteract the increasing lateral forces by for example a re direct of the main line via a supplementary anchor point or using an adjustable strop direct from the harness to a supplementary anchor point Gaining a good footing a
10. if the bar and chain are properly serviced and maintained see instructions under the heading General working instructions Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier The machine s vibration damping system reduces the transfer of vibration between the engine unit cutting equipment and the machine s handle unit The body of the chain saw including the cutting equipment is insulated from the handles by vibration damping units QA Cutting hardwoods most broadleaf trees creates more vibration than cutting softwoods most conifers Cutting English 9 GENERAL SAFETY PRECAUTIONS with cutting equipment that is blunt or faulty wrong type or badly sharpened will increase the vibration level ES WARNING Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation Contact your doctor if you experience symptoms of overexposure to vibration Such symptoms include numbness loss of feeling tingling pricking pain loss of strength changes in skin colour or condition These symptoms normally appear in the fingers hands or wrists These symptoms may be increased in cold temperatures Stop switch Use the stop switch to switch off the engine le The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from t
11. object e The chain brake A can either be activated manually by your left hand or automatically by the inertia release mechanism e The brake is applied when the front hand guard B is pushed forwards e This movement activates a spring loaded mechanism that tightens the brake band C around the engine drive system D clutch drum e The front hand guard is not designed solely to activate the chain brake Another important feature is that it reduces the risk of your left hand hitting the chain if you lose grip of the front handle 8 English The chain brake must be engaged when the chain saw is started to prevent the saw chain from rotating Use the chain brake as a parking brake when starting and when moving over short distances to reduce the risk of moving chain accidentally hitting your leg or anyone or anything close by To release the chain brake pull the front hand guard backwards towards the front handle Kickback can be very sudden and violent Most kickbacks are minor and do not always activate the chain brake If this happens you should hold the chain saw firmly and not let go The way the chain brake is activated either manually or automatically by the inertia release mechanism depends on the force of the kickback and the position of the chain saw in relation to the object that the kickback zone of the bar strikes If you get a violent kickback while t
12. there is WARNING Most chain saw accidents an increased risk of losing control For this reason these happen when the chain touches the special chainsaws should be used only for work in a tree operator You must use approved by persons who are trained in special cutting and working personal protective equipment whenever techniques and who are properly secured lift bucket you use the machine Personal protective ropes safety harness Regular chainsaws with wider equipment cannot eliminate the risk of spaced handles are recommended for all other cutting injury but it will reduce the degree of work at ground level injury if an accident does happen Ask your dealer for help in choosing the right WARNING Working in a tree requires the equipment use of special cutting and working techniques which must be observed in l S order to reduce the increased risk of CAUTION Never use a chain saw by holding it with one personal injury Never work in a tree hand A chain saw is not safely controlled with one hand unless you have received specific you can cut yourself Always have a secure firm grip professional training for such work around the handles with both hands including training in the use of safety and other climbing equipment such as harnesses ropes belts climbing irons snap hooks carabiners etc Machine s safety equipment In this section the machine s safety features and their function are explained For inspection
13. your control of the machine To make sure that none of the above might come within reach of your saw or be injured by falling trees 2 Check that the throttle lockout works correctly and is not damaged 3 Check that the stop switch works correctly and is not damaged CAUTION Follow the instructions above but do not use a Check that all handles are free from oil chain saw in a situation where you cannot call for help in N case of an accident Check that the anti vibration system works and is not damaged All tree maintenance work above ground level must be carried out by two or more persons with the right 6 Check that the muffler is securely attached and not training see instructions under the heading damaged Important At least one person should be on the 7 Check that all parts of the chain saw are tightened ground to carry out safe rescue procedures and or get correctly and that they are not damaged or missing help should an emergency arise 8 Check that the chain catcher is in place and not 3 During tree maintenance work above ground level the damaged working area should always be secured and marked 9 Check the chain tension out with signs tape or the like The person s on the ground should always inform the person s working General working instructions above before they enter the secure working area 4 Do not use the machine in bad weather such as IMPORTANT dense fog heavy rain strong wind intense cold etc Workin
14. 8 Fuel safety ri 18 STARTING AND STOPPING Starting and Stopping susanne 19 WORKING TECHNIQUES Before USE ida anna 21 General working instructions seese 21 How to avoid kickback unsern 28 MAINTENANCE cn EE RS 29 Carburettor adjustment aaa 29 Checking maintaining and servicing chain saw Safety equipment cocoocccccccccnnnccccnonononancncnnnnnnnnnnnnnnns 30 Muter anne see 31 Startel een 32 Air MIET Asmcnara reae E aE ee 34 Spark PIO adicta oda 34 Lubricating the bar tip sprocket 34 Adjustment of the oil pump occccccccccccnncnnncnncccnnco 35 Cooling system ssssssssssessseeesererrrrrrrrrrrrrrrrrrrrnrrrnne 35 Maintenance schedule coooccocnicicnncnncccnnccnancnnncnnnnos 36 Technical data ear 37 Bar and chain combinations nn 38 Saw chain filing and file gauges 38 EC declaration of conformity e 38 English 3 INTRODUCTION Dear Customer Congratulations on your choice to buy a Husqvarna product Husqvarna is based on a tradition that dates back to 1689 when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River for production of muskets The location was logical since water power was harnessed from the Huskvarna River to create the water powered plant During the more than 300 years of beeing the Husqvarna factory has produced a lot of different products from wood stoves to modern ki
15. English 21 WORKING TECHNIQUES suddenly Take great care when working on sloping ground 7 Take great care when cutting a tree that is in tension A tree that is in tension may spring back to its normal position before or after being cut If you position yourself incorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control Both situations can cause serious personal injury 8 Before moving your chain saw switch off the engine and lock the chain using the chain brake Carry the chain saw with the bar and chain pointing backwards Fit a guard to the bar before transporting the chain saw or carrying it for any distance When you put the chain saw on the ground lock the saw chain using the chain brake and ensure you have a constant view of the machine Switch the engine off before leaving your chain saw for any length of time General rules 1 If you understand what kickback is and how it happens then you can reduce or eliminate the element of surprise By being prepared you reduce the risk Kickback is usually quite mild but it can sometimes be very sudden and violent Always hold the chain saw firmly with your right hand on the top handle and your left hand on the front handle Wrap your fingers and thumbs around the handles You should use this grip whether you are right handed or left handed This grip minimises the 22 English effect of kickback and
16. Fr gelius Development director chainsaw R amp D 38 English 1151317 26
17. NANCE Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid e Carburettor malfunctions e Starting problems e Loss of engine power e Unnecessary wear to engine parts e Excessive fuel consumption e Remove the air filter after taking off the air filter cover When refitting make sure that the air filter seals tightly against the filter holder Clean the filter by brushing or shaking it CO The filter can be cleaned more thoroughly by washing it in water and detergent An air filter that has been in use for a long time cannot be cleaned completely The filter must therefore be replaced with a new one at regular intervals A damaged air filter must always be replaced A HUSQVARNA chain saw can be equipped with different types of air filter according to working conditions weather season etc Contact your dealer for advice 34 English Spark plug The spark plug condition is influenced by e Incorrect carburettor adjustment e An incorrect fuel mixture too much or incorrect type of oil e Adirty air filter These factors cause deposits on the spark plug electrodes which may result in operating problems and starting difficulties If the machine is low on power difficult to start or runs poorly at idle speed always check the spark plug first before taking any further action If the spark plug is dirty clean it and check that the electrode gap is 0 65 mm The
18. Operator s manual 1435 Please read the operator s manual carefully and make sure you understand the instructions before using the machine KEY TO SYMBOLS Symbols on the machine WARNING Chain saws can be dangerous Careless or incorrect use can result in serious or fatal injury to the operator or others Please read the operator s manual carefully and make sure you understand the instructions before using the machine Always wear e Approved protective helmet e Approved hearing protection e Protective goggles or a visor This product is in accordance with applicable EC directives m DP Noise emission to the environment according to the European Community s Directive The machine s emission is specified in chapter Technical data and on label Q UY Both of the operator s hands must be used to operate the chain saw Never operate a chain saw holding it with one hand only Never let the guide bar tip come in contact with any object amp S Use appropriate protections for foot leg and hand arm Never let the guide bar tip come in contact with any object WARNING Kickback may occur when the nose or tip of the guide bar touches an object and cause a lightning fast reverse reaction kicking the guide bar up and towards the operator May cause serious personal injury This saw should only be used by persons who are specially trained in tree maintenance work See operator
19. ain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree which will lead to a kickback Cutting with the bottom edge of the bar i e from the top of the object downwards is known as cutting on the pull stroke In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting Cutting on the pull stroke gives the operator better control over the chain saw and the position of the kickback zone 9 Follow the instructions on sharpening and maintaining your bar and chain When you replace the bar and chain use only combinations that are recommended by us See instructions under the headings Cutting equipment and Technical data Working with tree service chain saws from a rope and harness This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a rope and harness While it may form the basis of guidance and training literature it should not be regarded as a substitute for formal training General requirements working at height Operators of tree service chainsaws working at height from a rope and harness should never work alone A competent ground worker trained in appropriate emergency procedures should assist them Operators of tree service chainsaws for this work should be trained in general safe climbing and work positioning techniq
20. always use approved hearing protection WARNING Under no circumstances may the design of the machine be modified without the permission of the manufacturer Always use genuine accessories Non authorized modifications and or accessories can result in serious personal injury or the death of the operator or others WARNING A chain saw is a dangerous tool if used carelessly or incorrectly and can cause serious even fatal injuries It is very important that you read and understand the contents of this operator s manual WARNING The inside of the muffler contain chemicals that may be carcinogenic Avoid contact with these elements in the event of a damaged muffler WARNING Long term inhalation of the engine s exhaust fumes chain oil mist and dust from sawdust can represent a health risk WARNING The ignition system of this machine produces an electromagnetic field during operation This field may under some circumstances interfere with pacemakers To reduce the risk of serious or fatal injury we recommend persons with pacemakers to consult their physician and the pacemaker manufacturer before operating this machine 6 English Important IMPORTANT The machine is only designed for cutting wood You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data Never use the machine if you are fatigued while under the influence of alcohol or drugs
21. and maintenance see instructions under the heading Checking maintaining and servicing chain saw safety equipment See instructions under the heading What is what to find where these parts are located on your machine The life span of the machine can be reduced and the risk e Approved protective helmet of accidents can increase if machine maintenance is not carried out correctly and if service and or repairs are not carried out professionally If you need further information e Protective goggles or a visor please contact your nearest service workshop e Hearing protection e Gloves with saw protection WARNING Never use a machine with defective safety components Safety e Use appropriate protections for arm equipment must be inspected and maintained See instructions under the e Trousers with saw protection e Boots with saw protection steel toe cap and non slip sole heading Checking maintaining and er servicing chain saw safety equipment If Always have a first aid kit nearby your machine does not pass all the checks take the saw to a servicing dealer for repair English 7 GENERAL SAFETY PRECAUTIONS Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain if you get a kickback The chain brake reduces the risk of accidents but only you can prevent them Take care when using your saw and make sure the kickback zone of the bar never touches any
22. ardless of whether it is warm summer or cold winter weather As a chain saw manufacturer we have developed an optimal chain oil which with its vegetable oil base is also biodegradable We recommend the use of our own oil for both maximum chain life and to minimise environmental damage If our own chain oil is not available standard chain oil is recommended Never use waste oil Using waste oil can be dangerous to you and damage the machine and environment IMPORTANT When using vegetable based saw chain oil dismantle and clean the groove in the bar and saw chain before long term storage Otherwise there is a risk of the saw chain oil oxidizing which will result in the saw chain becoming stiff and the bar tip sprocket jamming English 13 GENERAL SAFETY PRECAUTIONS Filling with chain oil e All our chain saws have an automatic chain lubrication system On some models the oil flow is also adjustable e The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil However this safety feature requires that you use the right sort of chain oil if the oil is too thin it will run out before the fuel and that you adjust the carburetor as recommended a lean mixture may mean that the fuel lasts longer than the oil and that you also use the recommended cutting equipment a bar that is too long will use more chain oil Checking chain lubrication e Check the chain lubricat
23. as worn down to only 4 mm the chain must be replaced GENERAL SAFETY PRECAUTIONS Bar e To prolong the life of the bar you should turn it over Check regularly e Whether there are burrs on the edges of the bar Remove these with a file if necessary WARNING Most chain saw accidents happen when the chain touches the y operator Wear personal protective equipment See instructions under the heading Personal e Whether the groove in the bar has become badly protective equipment worn Replace the bar if necessary Do not tackle any job that you feel you are not adequately trained for See instructions under the headings Personal protective equipment How to e Whether the tip of the bar is uneven or badly worn If avoid kickback Cutting equipment and a hollow forms on the underside of the bar tip this is General working instructions due to running with a slack chain Avoid situations where there is a risk of kickback See instructions under the 4 heading Machine s safety equipment Use the recommended protective equipment and check its condition See instructions under the headings N Technical data and General safety precautions Check that all the chain saw safety features are working See instructions under the headings General working instructions and General safety precautions Never use a chain saw by holding it with one hand A chain saw is not safely controlled with one hand Always have a secure firm gri
24. d forwards Primer bulb Press the air purge repeatedly until fuel begins to fill the bulb The bulb need not be completely Ignition Set the stop switch to the start position Choke Set the choke control in the choke position Use the same starting procedure as for a cold engine but without setting the choke control in the choke position Starting Grip the front handle with your left hand and push the chain saw to the ground Grip the starter handle with your right hand and pull outthe starter cord slowly until you feel a resistance as the starter pawls engage and then pull firmly and rapidly Never twist the starter cord around your hand CAUTION Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended This can damage the machine Push down the choke control as soon as the engine fires which can be heard through a puff sound Keep on pulling the cord powerfully until the engine starts When English 19 STARTING AND STOPPING the engine starts quickly apply full throttle the throttle e Observe your surroundings and make sure that there start lock will automatically disengage is no risk of people or animals coming into contact with the cutting equipment IMPORTANT As the chain brake is still engaged the speed of the engine must be set to idling as soon as possible this is achieved by quickly disengaging the throttle lock This pre
25. dle speed T Adjust the idle speed with the T screw If it is necessary to re adjust turn the T screw clockwise while the engine is running until the chain starts to rotate Then turn anti clockwise until the chain stops When the idle speed is correctly adjusted the engine should run smoothly in every position and the engine speed should be safely below the speed at which the chain starts to rotate WARNING Contact your servicing dealer if the idle speed setting cannot be adjusted so that the chain stops Do not use the chain saw until it has been properly adjusted or repaired English 29 MAINTENANCE High speed jet H At the factory the engine is adjusted at sea level When working at a high altitude or in different weather conditions temperatures and atmospheric humidity it may be necessary to make minor adjustments to the high speed jet CAUTION If the high speed jet is screwed in too far it may damage the piston cylinder When test run at the factory the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance The carburettor s high speed jet is then locked using a limiter cap in the fully screwed out position The limiter cap limits the potential to adjust the high speed jet to at most half a turn Correctly adjusted carburettor When the carburettor is correctly adjusted the machine accelerates without hesitation and 4 cycles
26. e buyer will get the operator s manual Thank you for using a Husqvarna product Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice 4 English WHAT IS WHAT What is what on the chain saw 1 Front hand guard 16 Throttle control 2 Information and warning decal 17 Stop switch 3 Top handle 18 Bar 4 Adjuster screws carburettor 19 Chain 5 Filter cover 20 Bar tip sprocket 6 Fuel tank 21 Fixing eye for safety line 7 Spark plug cap 22 Clutch cover 8 Starter 23 Product and serial number plate 9 Starter handle 24 Chain tensioning screw 10 Front handle 25 Chain catcher 11 Chain oil tank 26 Spike bumper 12 Oil pump adjustment screw 27 Operator s manual 13 Air purge 28 Bar guard 14 Choke control 29 Combination spanner 15 Throttle lockout 30 Screwdriver English 5 GENERAL SAFETY PRECAUTIONS Before using a new chain saw Please read this manual carefully Check that the cutting equipment is correctly fitted and adjusted See instructions under the heading Assembly Refuel and start the chain saw See the instructions under the headings Fuel Handling and Starting and Stopping Do not use the chain saw until sufficient chain oil has reached the chain See instructions under the heading Lubricating cutting equipment Long term exposure to noise can result in permanent hearing impairment So
27. ed frequently until the chain is run in Check the chain tension regularly A correctly tensioned chain ensures good cutting performance and long life gt 2 Fitting a spike bumper To fit a spike bumper contact your service agent FUEL HANDLING Fuel Note The machine is equipped with a two stroke engine and must always be run using a mixture of petrol and two stroke oil It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained When mixing small amounts of fuel even small inaccuracies can drastically affect the ratio of the mixture WARNING Always ensure there is adequate ventilation when handling fuel e Use good quality unleaded or leaded petrol CAUTION Engines equipped with catalytic converters must be run on unleaded fuel mixtures Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used e The lowest recommended octane grade is 90 RON If you run the engine on a lower octane grade than 90 so called knocking can occur This gives rise to a high engine temperature and increased bearing load which can result in serious engine damage e When working with continuous high revs e g limbing a higher octane is recommended Environment fuel HUSQVARNA recommends the use of alkylate fuel either
28. elevant international standards dB A Vibration levels see note 3 Front handle m s Rear handle m s Chain bar Standard bar length inch cm Recommended bar lengths inch cm Usable cutting length inch cm Chain speed at max power m sec Pitch inch mm Thickness of drive links inch mm Number of teeth on drive sprocket T435 35 2 40 28 2900 12500 1 5 10000 Ikeda Denso CD NGK CMR7H 0 5 Walbro WT 804 0 26 3 9 0 17 Automatic 3 4 112 114 103 4 1 3 9 14 35 12 14 30 35 11 13 28 33 19 1 3 8 9 52 0 050 1 3 6 Note 1 Noise emissions in the environment measured as sound power Lwa in conformity with EC directive 2000 14 EC Note 2 Equivalent sound pressure level according to ISO 22868 is calculated as the time weighted energy total for noise pressure levels under various working conditions with the following time distribution 1 3 idling 1 3 max load 1 3 max speed Note 3 Equivalent vibration level according to ISO 22867 is calculated as the time weighted energy total for vibration levels under various working conditions with the following time distribution 1 3 idling 1 3 max load 1 3 max speed English 37 MAINTENANCE Bar and chain combinations The following combinations are CE approved Chain 7T Saw chain filing and file gauges inch mm inch mm Hab 5 32 40 so 30 o 0 025 0 85 5056981 03 5052437 01 EC declaration of conformit
29. en using a chain saw Always exercise care and use your common sense Avoid all situations which you consider to be beyond your capability If you still feel uncertain about operating procedures after reading these instructions you should consult an expert before continuing Do not hesitate to contact your dealer or us if you have any questions about the use of the chain saw We will willingly be of service and provide you with advice as well as help you to use your chain saw both efficiently and safely Attend a training course in chain saw usage if possible Your dealer forestry school or your library can GENERAL SAFETY PRECAUTIONS provide information about which training materials and e Fire Extinguisher and Shovel courses are available Generally clothes should be close fitting without restricting your freedom of movement Jat Work is constantly in progress to improve the design and IMPORTANT Sparks can come from the muffler the bar technology improvements that increase your safety and and chain or other sources Always have fire efficiency Visit your dealer regularly to see whether you extinguishing tools available if you should need them can benefit from new features that have been introduced Help prevent forest fires Personal protective equipment This top handle chainsaw is designed specifically for tree surgery and maintenance in the tree Due to the special A compact handle design closely spaced handles
30. g in bad weather is tiring and often brings qa Secon describes basic safety rules tor Uenga added risks such as icy ground unpredictable felling chain saw This information is never a substitute for direction ait professional skills and experience If you get into a o l situation where you feel unsafe stop and seek expert 5 Take great care when removing small branches and advice Contact your chain saw dealer service agent or avoid cutting bushes i e cutting many small branches an experienced chain saw user Do not attempt any task at the same time Small branches can be grabbed by that you feel unsure of the chain and thrown back at you causing serious Before using a chain saw you must understand the yury effects of kickback and how to avoid them See instructions under the heading How to avoid kickback Before using a chain saw you must understand the difference between cutting with the top and bottom edges of the bar See instructions under the headings How to avoid kickback and Machine s safety equipment 6 Make sure you can move and stand safely Check the area around you for possible obstacles roots rocks During tree maintenance work above ground level the chain saw must be secured Secure the chain saw by attaching a safety line to the fixing eye on the chain saw branches ditches etc in case you have to move Wear personal protective equipment See instructions under the heading Personal protective equipment
31. ght between the two depth gauge setting To sharpen cutting teeth you will need a round file and a A y file gauge See instructions under the heading Technical data for information on the size of file and gauge that are B recommended for the chain fitted to your chain saw When you sharpen a cutting tooth there are four important factors to remember 1 Filing angle e Check that the chain is correctly tensioned A slack chain will move sideways making it more difficult to CA sharpen correctly Tee a IRSA DO o Gonna any 2 Cutting angle e Always file cutting teeth from the inside face Reduce the pressure on the return stroke File all the teeth on one side first then turn the chain saw over and file the teeth on the other side 3 File position f 4 Round file diameter e File all the teeth to the same length When the length of the cutting teeth is reduced to 4 mm 0 16 the chain is worn out and should be replaced It is very difficult to sharpen a chain correctly without the l l min 4 mm S right equipment We recommend that you use our file 0 16 gauge This will help you obtain the maximum kickback reduction and cutting performance from your chain General advice on adjusting depth gauge setting e When you sharpen the cutting tooth A the depth gauge setting C will decrease To maintain optimal cutting performance the depth gauge B has to
32. handles Apply full throttle and activate the chain brake by tilting your left wrist forward onto the front hand guard Do not let go of the front handle The chain should stop immediately MAINTENANCE Throttle lockout e Make sure the throttle control is locked at the idle setting when the throttle lockout is released e Press the throttle lockout and make sure it returns to its original position when you release it e Check that the throttle control and throttle lockout move freely and that the return springs work properly e Start the chain saw and apply full throttle Release the throttle control and check that the chain stops and remains stationary If the chain rotates when the throttle control is in the idle position you should check the carburettor idle adjustment Chain catcher Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw Vibration damping system Regularly check the vibration damping units for cracks or deformation WS Cl Make sure the vibration damping units are securely attached to the engine unit and handle unit e Stop switch Start the engine and make sure the engine stops when you move the stop switch to the stop setting YP OE Muffler Never use a machine that has a faulty muffler English 31 MAINTENANCE Regularly check that the muffler is securely attached to mesh will cause
33. he kickback zone of the bar is farthest away from you the chain brake is designed to be activated by the inertia in the kickback direction GENERAL SAFETY PRECAUTIONS If the kickback is less violent or the kickback zone of the bar is closer to you the chain brake will be activated manually by the movement of your left hand e In the felling position the left hand is in a position that makes manual activation of the chain brake impossible With this type of grip that is when the left hand is placed so that it cannot affect the movement of the front hand guard the chain brake can only be activated by the inertia action Will my hand always activate the chain brake during a kickback No It takes a certain force to move the hand guard forward If your hand only lightly touches the front guard or slips over it the force may not be enough to trigger the chain brake You should also maintain a firm grip of the chain saw handles while working If you do and experience a kickback your hand may never leave the front handle and will not activate the chain brake or the chain brake will only activate after the saw has swung around a considerable distance In such instances the chain brake might not have enough time to stop the saw chain before it touches you There are also certain positions in which your hand cannot reach the front hand guard to activate the chain brake for example when the saw chain is held in felling pos
34. he user amp In areas with a hot dry climate there is a high risk of fires WARNING The exhaust fumes from the engine are hot and may contain sparks which can start a fire Never start the machine indoors or near combustible material CAUTION The muffler gets very hot during and after use This also applies during idling Be aware of the fire hazard especially when working near flammable substances and or vapours WARNING Never use a saw without a muffler or with a damaged muffler A damaged muffler may substantially increase the noise level and the fire hazard Keep fire fighting equipment handy 10 English Cutting equipment This section describes how to choose and maintain your cutting equipment in order to e Reduce the risk of kickback e Reduce the risk of the saw chain breaking or jumping off the bar e Obtain optimal cutting performance e Extend the life of cutting equipment e Avoid increasing vibration levels General rules e Only use cutting equipment recommended by us See instructions under the heading Technical data A DS GI e Keep the chain s cutting teeth properly sharpened Follow our instructions and use the recommended file gauge A damaged or badly sharpened chain increases the risk of accidents e Maintain the correct depth gauge setting Follow our instructions and use the recommended depth gauge clearance Too large a clearance increases the risk of kickback
35. ion each time you refuel See instructions under the heading Lubricating the bar tip sprocket Aim the tip of the bar at a light coloured surface about 20 cm 8 inches away After 1 minute running at 3 4 throttle you should see a distinct line of oil on the light surface If the chain lubrication is not working e Check that the oil channel in the bar is not obstructed Clean if necessary 14 English e Check that the groove in the edge of the bar is clean Clean if necessary e Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked Clean and lubricate if necessary If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your service agent Chain drive sprocket The clutch drum is fitted with a Spur sprocket the chain sprocket is welded on the drum Regularly check the degree of wear on the drive sprocket Replace if wear is excessive Replace the drive sprocket whenever you replace the chain Checking wear on cutting equipment Check the chain daily for e Visible cracks in rivets and links e Whether the chain is stiff e Whether rivets and links are badly worn Replace the saw chain if it exhibits any of the points above We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn When the length of the cutting teeth h
36. ish MAINTENANCE Undo the screw in the centre of the pulley and remove the pulley Insert and fasten a new starter cord to the pulley Wind approx 3 turns of the starter cord onto the pulley Connect the pulley to the recoil spring so that the end of the spring engages in the pulley Fit the screw in the centre of the pulley Insert the starter cord through the hole in the starter housing and the starter handle Make a secure knot in the end of the starter cord Tensioning the recoil spring Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise Note Check that the pulley can be turned at least a further 1 2 turn when the starter cord is pulled all the way out Changing a broken recoil spring Lift up the starter pulley See instructions under the heading Changing a broken or worn starter cord Remember that the recoil spring is coiled under tension in the starter housing Remove the cassette with the recoil spring from the starter Lubricate the recoil spring with light oil Fit the cassette with recoil spring in the starter Fit the starter pulley and tension the recoil spring Fitting the starter To fit the starter first pull out the starter cord and place the starter in position against the crankcase Then slowly release the starter cord so that the pulley engages with the pawls Fit and tighten the screws that hold the starter English 33 MAINTE
37. ition Will my inertia activated chain brake always activate during kickback in the event of a kickback No First your brake must be in working order Second the kickback must be strong enough to activate the chain brake If the chain brake is too sensitive it would activate all the time which would be a nuisance Will my chain brake always protect me from injury in the event of a kickback No First the chain brake must be in working order to provide the intended protection Second it must be activated during the kickback as described above to stop the saw chain Third the chain brake may be activated but if the bar is too close to you the brake might not have enough time to slow down and stop the chain before the chain saw hits you Only you and proper working technique can eliminate kickback and its danger Throttle lockout The throttle lockout is designed to prevent accidental operation of the throttle control When you press the lock A i e when you grasp the handle it releases the throttle control B When you release the handle the throttle control and the throttle lockout both move back to their original positions This arrangement means that the throttle control is automatically locked at the idle setting A B Chain catcher The chain catcher is designed to catch the chain if it snaps or jumps off This should not happen if the chain is properly tensioned see instructions under the heading Assembly and
38. ition in the tree on the right side and cut on the pull stroke Next make the bottom cut so that it finishes exactly at the end of the top cut WORKING TECHNIQUES The directional cuts should run 1 4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45 The line where the two cuts meet is called the directional cut line This line should be perfectly horizontal and at right angles 90 to the chosen felling direction Felling cut The felling cut is made from the opposite side of the tree and it must be perfectly horizontal Try to take a correct position so you are able to cut on the pull stroke Make the felling cut about 3 5 cm 1 5 2 inches above the bottom directional cut Set the spike bumper if one is fitted just behind the felling hinge Use full throttle and advance the chain bar slowly into the tree Make sure the tree top does not start to move in the opposite direction to your intended felling direction Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1 10 of the trunk diameter The uncut section of the trunk is called the felling hinge The felling hinge controls the direction that the tree falls in All control over the felling direction is lost if the felling hinge is too narrow or non existent or if the directional cuts and felling cut are badl
39. ke care when handling fuel and chain oil Be aware of the risks of fire explosion and those associated with inhalation Fuel safety e Never refuel the machine while the engine is running e Make sure there is plenty of ventilation when refuelling or mixing fuel petrol and 2 stroke oil 18 English e Move the machine at least 3 m from the refuelling point before starting it Min 3m e Never start the machine 1 If you have spilt fuel or chain oil on the machine Wipe off the spillage and allow remaining fuel to evaporate 2 If you have spilt fuel on yourself or your clothes change your clothes Wash any part of your body that has come in contact with fuel Use soap and water 3 Ifthe machine is leaking fuel Check regularly for leaks from the fuel cap and fuel lines WARNING Never use a machine with visible damage to the spark plug guard and ignition cable A risk of sparking arises which can cause a fire Transport and storage e Always store the chain saw and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment electric motors relays switches boilers and the like e Always store fuel in an approved container designed for that purpose e For longer periods of storage or for transport of the chain saw the fuel and chain oil tanks should be emptied Ask where you can dispose of waste fuel and chain oil at your local petr
40. lets you keep the chain saw under control Most kickback accidents happen during limbing Make sure you are standing firmly and that there is nothing in the way that might make you trip or lose your balance Lack of concentration can lead to kickback if the kickback zone of the bar accidentally touches a branch nearby tree or some other object Have control over the workpiece If the pieces you intend to cut are small and light they can jam in the saw chain and be thrown towards you Even if this does not need to be a danger you may be surprised and lose control of the saw Never saw stacked logs or branches without first separating them Only saw one log or one piece at a time Remove the cut pieces to keep your working area safe Never use the chain saw above shoulder height and try not to cut with the tip of the bar Never use the chain saw one handed 5 Always use a fast cutting speed i e full throttle WORKING TECHNIQUES 6 Ifyou have to cut branches or the like that are above shoulder height a working platform or scaffold tower is recommended 7 Take great care when you cut with the top edge of the bar i e when cutting from the underside of the object This is known as cutting on the push stroke The chain tries to push the chain saw back towards the user If the saw chain is jamming the saw may be pushed back at you 5 8 Unless the user resists this pushing force there is a risk that the ch
41. line e pull the saw from the kerf whilst lifting the branch as necessary e if necessary use a handsaw or second chain saw to release the trapped saw by cutting a minimum of 30 cm away from the trapped saw Whether a handsaw or a chainsaw is used to free a stuck saw the release cuts should always be outboard toward the tips of the branch in order to prevent the saw being taken with the section and further complicating the situation Basic cutting technique WARNING Never use a chain saw by holding it with one hand A chain saw is not safely controlled with one hand you can cut yourself Always have a secure firm grip around the handles with both hands General e Always use full throttle when cutting e Reduce the speed to idle after every cut running the engine for too long at full throttle without any load i e without any resistance from the chain during cutting can lead to serious engine damage e Cutting from above Cutting on the pull stroke e Cutting from below Cutting on the push stroke Cutting on the push stroke increases the risk of kickback See instructions under the heading How to avoid kickback Terms Cutting General term for cutting through wood Limbing Cutting branches off a felled tree Splitting When the object you are cutting breaks off before the cut is complete There are five important factors you should consider before making a cut 1 Make sure the cutting equipment
42. must be performed on the machine Most of the items are described in the Maintenance section Daily maintenance Weekly maintenance Monthly maintenance Check the brake band on the chain brake for wear Replace when less than 0 6 mm 0 024 inch remains at the most worn point On chain saws without a catalytic Clean the outside of the machine converter check the cooling system weekly Check that the components of the throttle control work safely Throttle lockout and throttle control Check the starter starter cord and Check the clutch centre clutch drum return spring and clutch spring for wear Clean the chain brake and check that it operates safely Make sure that the Check that the vibration damping Clean the spark plug Check that the chain catcher is undamaged and elements are not damaged electrode gap is 0 65 mm replace it if necessary The bar should be turned daily for more even wear Check the lubrication hole in the bar to be sure it File off any burrs from the edges of is not clogged Clean the bar groove the bar If the bar has a sprocket tip this should be lubricated Check that the bar and chain are Clean or replace the spark arrestor Check the fuel filter and the fuel hose getting sufficient oil mesh on the muffler Replace if necessary Clean the outside of the carburettor Check the saw chain with regard to visible cracks in the rivets and links whether the saw chain is stiff or Emp
43. nsion and make the tree or branch break at the point of maximum tension Never cut straight through a tree or branch that is in tension How to avoid kickback WARNING Kickback can happen very suddenly and violently kicking the chain saw bar and chain back at the user If this happens when the chain is moving it can cause very serious even fatal injuries It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique What is kickback The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar known as the kickback zone touches an object Kickback always occurs in the cutting plane of the bar Normally the chain saw and bar are thrown backwards and upwards towards the user However the chain saw may move in a different direction depending on the way it was being used when the kickback zone of the bar touched the object Kickback only occurs if the kickback zone of the bar touches an object 28 English MAINTENANCE General The user must only carry out the maintenance and service work described in this manual IMPORTANT Any maintenance other than that described in this manual must be carried out by your servicing dealer retailer Carburettor adjustment Due to existing environmental and emissions legislation your chain saw i
44. ol station e The bar guard must always be fitted to the cutting attachment when the machine is being transported or in storage in order to prevent accident contact with the sharp chain Even a non moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain Long term storage Empty the fuel oil tanks in a well ventilated area Store the fuel in approved cans in a safe place Fit the bar guard Clean the machine See instructions under the heading Maintenance schedule Ensure the machine is cleaned and that a complete service is carried out before long term storage STARTING AND STOPPING Starting and stopping WARNING Note the following before starting The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting Never start a chain saw unless the bar chain and all covers are fitted correctly Otherwise the clutch can come loose and cause personal injuries Place the machine on firm ground Make sure you have a secure footing and that the chain cannot touch anything If you need to start the chain saw in the tree see instructions under the heading Starting the saw in the tree under the section Working techniques Keep people and animals well away from the working area Cold engine Starting The chain brake must be engaged when the chain saw is started Activate the brake by moving the front hand guar
45. ombinations recommended by Husqvarna See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend Bar e Length inches cm links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket e Number of drive links The number of drive links is determined by the length of the bar the chain pitch and the number of teeth on the bar tip sprocket e Bar groove width inches mm The groove in the bar must match the width of the chain drive links e Chain oil hole and hole for chain tensioner The bar must be matched to the chain saw design EA e A O Chain e Chain pitch inches Drive link width mm inches e Number of drive links Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth e Never use a blunt chain When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small If the chain is very blunt it will produce wood powder and no chips or shavings e A sharp chain eats its way through the wood and produces long thick chips or shavings English 11 GENERAL SAFETY PRECAUTIONS e The cutting part of the chain is called the cutter and Sharpening cutting teeth consists of a cutting tooth A and the depth gauge B The cutters cutting depth is determined by the y difference in hei
46. op cutting about 2 3 of the way through the log Cv Turn the log and finish the cut from the opposite side E The log is supported at one end There is a high risk that it will split Start by cutting from below about 1 3 of the way through Er Finish by cutting from above so that the two cuts meet S The log is supported at both ends There is a high risk that the chain will jam Start by cutting from above about 1 3 of the way through Finish by cutting from below so that the two cuts meet English 25 WORKING TECHNIQUES Limbing When limbing thick branches you should use the same approach as for cutting Cut difficult branches piece by piece Felling technique for tree tops WARNING It takes a lot of experience to fell a tree Inexperienced users of chain saws should not fell trees Do not attempt any task that you feel unsure of Safe distance During tree maintenance work above ground level the working area must always be secured and marked out with signs tape or the like The safe distance between the top of the tree that is to be felled and the nearest workplace must be at least 2 1 2 times the height of the tree Make sure that no one else is in this risk zone before or during felling Felling direction The aim is to fell the tree in a position where you can limb and cross cut the log as easily as possible Y
47. ou want it to fall in a location where you can stand and move about safely The main thing to avoid is that the falling tree top should get jammed in another tree Taking down a jammecd tree top is very dangerous see point 4 in this section Once you have decided which way you want the top of the tree to fall you must assess which way the top of the tree would fall naturally Several factors affect this e Lean of the tree e Bend e Wind direction 26 English e Arrangement of branches e Weight of snow You may find you are forced to let the tree top fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended Another very important factor which does not affect the felling direction but does affect your safety is to make sure the tree has no damaged or dead branches that might break off and hit you during felling WARNING During critical felling operations hearing protectors should be lifted immediately when sawing is completed so that sounds and warning signals can be heard Topping a tree Topping a tree is done using three cuts First you make the directional cuts which consist of the top cut and the bottom cut then you finish with the felling cut By placing these cuts correctly you can control the felling direction very accurately Directional cuts To make the directional cuts you begin with the top cut Try to take your pos
48. p around the handles with both hands English 15 ASSEMBLY Fitting the bar and chain WARNING Always wear gloves when working with the chain Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle Unscrew the bar nut and remove the clutch cover chain brake Take off the transportation guard Fit the bar over the bar bolts Place the bar in its rearmost position Place the chain over the drive sprocket locate it in the groove on the bar Begin on the top edge of the bar Make sure that the edges of the cutting links are facing forward on the top edge of the bar Fit the clutch cover and locate the chain adjuster pin in the hole in the bar Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is 16 English correctly located in the groove in the bar Tighten the bar nuts finger tight ign gs Tension the chain by turning the chain tensioning screw clockwise using the combination spanner The chain should be tensioned until it does not sag from the underside of the bar See instructions under the heading Tensioning the chain The chain is correctly tensioned when it does not sag from the underside of the bar but can still be turned easily by hand Hold up the bar tip and tighten the bar nuts with the combination spanner When fitting a new chain the chain tension has to be check
49. peed during the first 10 hours CAUTION If the chain rotates while idling the T screw must be turned anti clockwise until the chain stops Rec idle speed 2900 rpm Fine adjustment When the machine has been run in the carburettor should be finely adjusted The fine adjustment should be carried out by a qualified person First adjust the L jet then the idling screw T and then the H jet Changing the type of fuel Fine tuning may be required if the chain saw after changing the type of fuel performs differently with regard to starting acceleration maximum speed etc Conditions e Before any adjustments are made the air filter should be clean and the cylinder cover fitted Adjusting the carburettor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned This can give rise to serious engine damage e Donotattemptto adjust the L and H jets beyond either stop as this could cause damage e Now start the machine according to the starting instructions and let it warm up for 10 minutes e Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects Low speed jet L Turn the low speed jet L clockwise until it stops If the engine accelerates poorly or idles unevenly turn the low speed jet L anticlockwise until good acceleration and idling are achieved Fine adjustment of the i
50. s equipped with movement limiters on the carburettor adjuster screws These limit the adjustment possibilities to a maximum of a 1 4 turn Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions Function e The carburettor governs the engine s speed via the throttle control Air and fuel are mixed in the carburettor The air fuel mixture is adjustable Correct adjustment is essential to get the best performance from the machine e Adjusting the carburettor means that the engine is adapted to local operating conditions e g climate altitude petrol and the type of 2 stroke oil e The carburettor has three adjustment controls L Low speed jet H High speed jet T Idle adjustment screw e The Land H jets are used to adjust the supply of fuel to match the rate that air is admitted which is controlled with the throttle If they are screwed clockwise the air fuel ratio becomes leaner less fuel and if they are turned anti clockwise the ratio becomes richer more fuel A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed e The T screw regulates the throttle setting at idle speed If the T screw is turned clockwise this gives a higher idle speed turning it anti clockwise gives a lower idle speed Basic settings and running in The basic carburettor settings are adjusted during testing at the factory Avoid running at a too high s
51. slack chain may jump off and cause serious or even fatal injury m Qe A The more you use a chain the longer it becomes It is therefore important to adjust the chain regularly to take up the slack Check the chain tension every time you refuel NOTE A new chain has a running in period during which you should check the tension more frequently Tension the chain as tightly as possible but not so tight that you cannot pull it round freely by hand a e Loosen the bar nut that holds the clutch cover and chain brake Use the combination spanner e Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner Tighten the chain until it does not sag from the underside of the bar Use the combination spanner to tighten the bar nut while holding up the tip of the bar Check that you can pull the saw chain round freely by hand and that there is no slack on the underside of the bar gt Be The position of the chain tensioning screw on our chain saws varies from model to model See instructions under the heading What is what to find out where it is on your model Lubricating cutting equipment WARNING Poor lubrication of cutting equipment may cause the chain to snap which could lead to serious even fatal injuries Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics reg
52. t the working position can be assisted by use of a temporary foot stirrup created from an endless sling Starting the saw in the tree When starting the saw in the tree the operator should a apply the chain brake before starting b hold saw on either the left or right of the body when starting 1 on the left side hold the saw with the left hand on the front handle and thrust the saw away from the body while holding the pull starter cord in the other hand 2 onthe right side hold the saw with the right hand on either handle and thrust the saw away from the body while holding the pull starter cord in the left hand The chain brake should always be engaged before lowering a running saw onto its strop Operators should always check the saw has sufficient fuel before undertaking critical cuts One hand use of the chainsaw Operators should never use a chain saw onehanded Operators should never e cut with the kickback zone at the tip of the chainsaw guide bar e hold and cut sections e attempt to catch falling sections e Cut in the tree when he she is only secured with one rope always use 2 secured lines e check condition of harness belt and ropes at regular frequent intervals 24 English Freeing a trapped saw If the saw should become trapped during cutting operators should e switch off the saw and attach it securely to the tree inboard i e towards the truck side of the cut or to a separate tool
53. tchen appliances sewing machines bicycles motorcycles etc In 1956 the first motor driven lawn mowers appeared followed by chain saws in 1959 and it is within this area Husqvarna is working today Today Husqvarna is one of the leading manufacturers in the world of forest and garden products with quality as our highest priority The business concept is to develop manufacture and market motor driven products for forestry and gardening as well as for building and construction industry Husqvarna s aim is also to be in the front edge according to ergonomics usability security and environmental protection That is the reason why we have developed many different features to provide our products within these areas We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to come The purchase of one of our products gives you access to professional help with repairs and service whenever this may be necessary lf the retailer who sells your machine is not one of our authorised dealers ask for the address of your nearest service workshop It is our wish that you will be satisfied with your product and that it will be your companion for a long time Think of this operator s manual as a valuable document By following its content using service maintenance etc the life span and the second hand value of the machine can be extended If you will sell this machine make sure that th
54. the engine to overheat and may lead to the machine serious damage Note The mesh must be replaced if it is damaged If the mesh is blocked the machine will overheat and this will cause damage to the cylinder and piston Never use a machine with a muffler that is in poor condition Never use a muffler if the spark arrestor mesh is missing or defective Starter WARNING When the recoil spring is wound up in the starter housing it is under tension and can if handled carelessly pop out and cause personal injury Care must be exercised when replacing the return spring or the starter cord Wear protective glasses and protective gloves Changing a broken or worn starter cord co e Loosen the screws that hold the starter against the crankcase and remove the starter Loosen the screws and nuts Remove and check that the muffler is ok e Pull out the cord approx 30 cm and hook it into the notch in the rim of the pulley Release the recoil spring by letting the pulley rotate slowly backwards The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator The exhaust gases are hot and can contain sparks which may cause fire if directed against dry and combustible material The muffler is equipped with a special spark arrestor mesh The spark arrestor mesh should be cleaned once a month This is best done with a wire brush A blocked 32 Engl
55. ty the fuel tank and clean the Clean the carburettor compartment whether the rivets and links are inside abnormally worn Replace if necessary Sharpen the chain and check its tension and condition Check the drive Clean the air filter Replace if Empty the oil tank and clean the sprocket for excessive wear and necessary inside replace if necessary Check all cables and connections Clean the starter units air intake Check that nuts and screws are tight Check that the stop switch works correctly Check that there are no fuel leaks from the engine tank or fuel lines On chain saws with a catalytic converter check the cooling system daily Check the condition of the air filter 36 English MAINTENANCE Technical data Engine Cylinder displacement cm Cylinder bore mm Stroke mm Idle speed rpm Recommended max speed rpm Power kW rpm Ignition system Manufacturer of ignition system Type of ignition system Spark plug Electrode gap mm Fuel and lubrication system Manufacturer of carburettor Carburettor type Fuel tank capacity litre Oil pump capacity at 9 500 rpm ml min Oil tank capacity litre Type of oil pump Weight Chain saw without bar or chain empty tanks kg Noise emissions see note 1 Sound power level measured dB A Sound power level guaranteed Lwa dB A Sound levels see note 2 Equivalent sound pressure level at operator s ear measured according to r
56. ues and shall properly equipped with harnesses ropes strops karabiners and other equipment for maintaining secure and safe working positions for both themselves and the saw Preparing to use the saw in the tree The chain saw should be checked fuelled started and warmed up by the ground worker and the chain brake should be engaged before it is sent up to the operator in the tree The chainsaw should be fitted with a suitable strop for attaching to the operator s harness a choke the strop around the attachment point on the rear of the saw AK b provide suitable karabiners to allow indirect i e via the strop and direct attachment i e at the attachment point on the saw of saw to the operators harness c ensure the saw is securely attached when it is being sent up to the operator d ensure the saw is secured to the harness before it is disconnected from the means of ascent The saw should only be attached to the recommended attachment points on the harness These may be at mid point front or rear or at the sides Where possible attaching the saw to centre rear mid point will keep it clear of climbing lines and support its weight centrally down the operator s spine When moving the saw from any attachment point to another operators should ensure it is secured in the new position before releasing it from the previous attachment point Using the chainsaw in the tree An analysis of accidents with these saws
57. vents unnecessary wear to the clutch clutch drum and brake band e Always hold the saw with both hands The right hand should be on the top handle and the left hand on the front handle All people whether right or left handed should use this grip Use a firm grip with thumbs and fingers encircling the chain saw handles Note Reactivate the chain brake by pushing the front hand guard back towards the front handle The chain saw is now ready for use WARNING Long term inhalation of the engine s exhaust fumes chain oil mist Stopping and dust from sawdust can represent a health risk e Never start a chain saw unless the bar chain and all KZ covers are fitted correctly See instructions under the heading Assembly Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury The engine is stopped by pushing the stop switch to the stop position e The chain brake should be activated when starting Se instructions under the heading Start and stop Do not drop start This method is very dangerous because you may lose control of the saw e Never start the machine indoors Exhaust fumes can be dangerous if inhaled 20 English WORKING TECHNIQUES Basic safety rules Before use Check that the chain brake works correctly and is not damaged y Look around you To ensure that people animals or other things cannot affect
58. will not jam in the cut WORKING TECHNIQUES 3 Make sure the chain will not strike the ground or any other object during or after cutting 5 Do the conditions and surrounding terrain affect how safely you can stand and move about Two factors decide whether the chain will jam or the object that you are cutting will split the first is how the object is supported before and after cutting and the second is whether it is in tension In most cases you can avoid these problems by cutting in two stages from the top and from the bottom You need to support the object so that it will not trap the chain or split during cutting WARNING If the chain jams in the cut stop the engine Don t try to pull the chain saw free If you do you may be injured by the chain when the chain saw suddenly breaks free Use a lever to open up the cut and free the chain saw The following instructions describe how to handle the commonest situations you are likely to encounter when using a chain saw Cutting The log is lying on the ground There is little risk of the chain jamming or the object splitting However there is a risk that the chain will touch the ground when you finish the cut TA ee Ee Cut all the way through the log from above Avoid letting the chain touch the ground as you finish the cut Maintain full throttle but be prepared for what might happen If itis possible can you turn the log st
59. y Applies to Europe only Husqvarna AB SE 561 82 Huskvarna Sweden tel 46 36 146500 declares under sole responsibility that the chain saw Husqvarna T435 from 2009 s serial numbers and onwards the year is clearly stated in plain text on the type plate with subsequent serial number is in conformity with the requirements of the COUNCILS DIRECTIVES of June 22 1998 relating to machinery 98 37 EC annex IIA of December 15 2004 relating to electromagnetic compatibility 2004 108 EC of May 8 2000 relating to the noise emissions in the environment 2000 14 EC For information relating to noise emissions see the chapter Technical data The following standards have been applied CISPR 12 2001 EN ISO 11681 2 Notified body 0404 SMP Svensk Maskinprovning AB Fyrisborgsgatan 3 SE 754 50 Uppsala Sweden has carried out EC type examination in accordance with the machinery directive s 98 37 EC article 8 point 2c The certificates for EC type examination in accordance with annex VI have the numbers 404 08 1276 In addition SMP Svensk Maskinprovning AB Fyrisborgsgatan 3 SE 754 50 Uppsala Sweden has certified conformity with annex V of the Council s Directive of May 8 2000 relating to the noise emissions in the environment 2000 14 EC The certificates have the numbers 01 161 080 The supplied chain saw conforms to the example that underwent EC type examination Huskvarna January 9 2009 Ep Bengt
60. y placed We recommend that you use a bar that is longer than the diameter of the tree so that you can make the felling cut and directional cuts with single cutting strokes See the Technical data section to find out which lengths of bar are recommended for your saw There are methods for felling trees with a diameter larger than the bar length However these methods involve a much greater risk that the kickback zone of the bar will come into contact with the tree A WARNING Unless you have special training we advise you not to fell trees with a diameter larger than the bar length of your saw Freeing a tree that has fallen badly Cutting trees and branches that are in tension Preparations Work out which side is in tension and where the point of maximum tension is i e where it would break if it was bent even more AAN sar 3 eLo Ar Decide which is the safest way to release the tension and whether you are able to do it safely In complicated situations the only safe method is to put aside your chain saw and use a winch English 27 WORKING TECHNIQUES General advice Cutting the trunk into logs Position yourself so that you will be clear of the tree or See instructions under the heading Basic cutting branch when the tension is released technique Make one or more cuts at or near the point of maximum tension Make as many cuts of sufficient depth as necessary to reduce the te

Husqvarna T435 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents