Hunter TYPE 2 User's Manual
Contents
1. OF THE BLADE TIPS SEE FIGURE 1 FOR MOUNTING DISTANCES 8 FT MIN _ _ _ 24 CLEARANCE TO OBSTRUCTIONS CEILING TO FLOOR C Xx 84 MIN TO FLOOR FIGURE 1 INSPECTION OF FAN AND LIGHT A UNPACK UNIT CAREFULLV TO AVOID ANV DAMAGE TO THE COMPONENTS B CHECK FOR ANY SHIPPING DAMAGE TO THE MOTOR FAN BLADES SWITCH HOUSING AND GLOBE IF MORE THAN ONE FAN IS BEING INSTALLED KEEP THE MATCHED AND BALANCED FAN BLADES IN SETS AS THEY WERE SHIPPED SHOULD ONE OF THE FAN BLADES BECOME DAMAGED DURING SHIPMENT RETURN ALL BLADES IN THE SET FOR REPLACEMENT C CHECK CONTENTS TO BE CERTAIN IT CONTAINS A BAG OF PARTS INSTALLATION OF OUTLET BOX AND ROUGH IN WIRING YOUR HUNTER CEILING FAN WITH ACCESSORIES CAN WEIGH UP TO 35 LBS THE FOLLOWING PRECAUTIONS MUST BE TAKEN FOR SAFETY AND TO ENSURE THAT YOUR FAN IS SECURELY MOUNTED TO THE CEILING BE CERTAIN ELECTRICITY IS OFF AT THE FUSE PANEL WHEN INSPECTING OR REPAIRING INSTALLATION SITE ALL WIRING MUST MEET LOCAL AND NATIONAL ELECTRICAL CODES DO NOT MOUNT DIRECTLY TO AN UNSUPPORTED CEILING OR TO AN ELECTRICAL OUTLET MOUNTING MUST SUPPORT A 35 LB FAN WITH ACCESSORIES A SECURE A METALLIC OUTLET BOX 4 X 1 1 2 OR 4 X 1 2 DEEP TO A 2 X 4 CROSS BRACE BETWEEN TWO CEILING JOISTS AS SHOWN IN FIGURE 2 THE OUTLET BOX MUST BE RECESSED IN THE CEILING BY 1 16 MINIMUM SECURE THE OUTLET BOX TO THE CROSS BRACE BY DRILLING 2 PILOT HOLES NO LARGER THAN THE MINOR DIAMETER O2. MOUNT BLADES TO FAN WITH WOOD PADDLES LOCATED UNDERNEATH BLADE BRACKETS C A BLADE BALANCING KIT HAS BEEN PROVIDED WITH YOUR FAN SHOULD THE FAN WOBBLE IN OPERATION YOU MAY USE THIS KIT TO CORRECT THE BALANCE PER THE INSTRUCTIONS SUPPLIED WITH THE KIT STEP 9 BULB AND GLOBE INSTALLATION A INSTALL 2 60W LIGHT BULBS NOT INCLUDED THREAD THE 3 8 32 KNURLED HEAD SCREWS HALFWAY INTO THE 3 THREADED HOLES IN THE SIDE OF THE SWITCH HOUSING SECURE THE GLASS GLOBE TO THE SWITCH HOUSING BY CAREFULLY TIGHTENING THE 3 SCREWS NOTE SHOULD GLOBE EMIT ANY SOUND WHEN FAN IS RUNNING RE ADJUST 3 GLOBE MOUNTING SCREWS UNTIL SOUND HAS DISAPPEARED MOTOR BLADE amp BLADE BRACKET REVERSING SWITCH PULL CHAIN SWITCH BREAKAWAY CONNECTOR a4 PURCHASED ACCESSORY CHAIN SWITCH HOUSING IF DESIRED BLADE MOUNTING SCREWS NOTE MAKE CERTAIN ALL SCREWS ARE TIGHT SCREWDRIVER GLOBE FIGURE 9 FORM NO 40987 01 REV 5 94 PAGE 4 STEP 10 OPERATION OF FAN A TURN ELECTRICAL SERVICE ON AT MAIN PANEL B SWITCH OPERATES IN THIS SEQUENCE HIGH MEDIUM LOW OFF PULL CHAIN SLOWLY TO OPERATE ALSO RELEASE THE CHAIN SLOWLY SO AS TO PREVENT CHAIN FROM FLYING UP INTO BLADES POSSIBLY RESULTING IN DAMAGE TO BLADES OR PULL CHAIN THE BREAKAWAY CONNECTOR IS DESIGNED TO SEPARATE FROM THE CHAIN AT A PREDETERMINED FORCE IF THIS SEPARATION OCCURS SIMPLY REINSERT THE CONNECTOR IT CAN BE USED AGAIN AND AGAIN SEE FIGURE 9 C MOTOR IS ELECTRI
3. CALLY REVERSIBLE WHEN FIRST OPERATING FAN DETERMINE DIRECTION OF AIR FLOW IF YOU WISH TO CHANGE DIRECTION SWITCH FAN OFF AND ALLOW TO STOP SLIDE REVERSING SWITCH TO THE OPPOSITE POSITION AND SWITCH FAN BACK ON SEE FIGURE 9 EXTENSION PIPES IF YOUR CEILING IS HIGHER THAN EIGHT FEET YOU MAY ELECT TO USE A LONGER HANGER PIPE EXTENSION PIPES ARE AVAILABLE AT YOUR HUNTER DEALER AND MAY BE ADAPTED TO FIT YOUR FAN SPEED CONTROL AS AN OPTION A WALL MOUNTED SPEED CONTROL SWITCH IS AVAILABLE FROM YOUR HUNTER DEALER TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE 1 NOTHING HAPPENS FAN DOES NOT MOVE 2 LOOSE WIRE CONNECTIONS OR WRONG CONNECTIONS 3 MOTOR REVERSING SWITCH NOT ENGAGED 4 PULL CHAIN SWITCH NOT ON 1 POWER TURNED OFF OR FUSE BLOWN SOLUTION 1 TURN POWER ON OR REPLACE FUSE 2 LOOSEN CANOPY CHECK ALL CONNECTIONS TURN POWER OFF WHILE CHECKING 3 PUSH SWITCH FIRMLY TO ONE SIDE OR THE OTHER 4 PULL SWITCH CHAIN NOTE IF BLADES WILL NOT TURN BY HAND CONTACT YOUR NEAREST SERVICE REPRESENTATIVE 2 NOISY OPERATION 1 BLADE BRACKETS LOOSELY SCREWED TO MOTOR 2 BLADE SCREWED LOOSELY TO BLADE BRACKET 3 BLADE CRACKED 4 NON APPROVED SPEED CONTROL BEING USED 5 GLOBE IS VIBRATING AND EMITTING NOISE 1 TIGHTEN SCREWS UNTIL SNUG 2 TIGHTEN SCREWS 3 REPLACE ENTIRE SET OF BLADES 4 CHANGE TO APPROVED SPEED CONTROL 5 RE ADJUST 3 GLOBE MOUNTING SCREWS 3 EXCESSIVE WOBBLING 1 UNBALAN
4. CAUTION WARNING STEP 1 STEP 2 STEP 3 CAUTION CAUTION INSTALLATION INSTRUCTIONS FOR TYPE 2 HUNTER CEILING FAN WITH LIGHT READ AND SAVE THESE INSTRUCTIONS 1 READ ENTIRE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION 2 TO AVOID POSSIBLE ELECTRICAL SHOCK BE CERTAIN ELECTRICITY IS SHUT OFF AT MAIN PANEL BEFORE WIRING 3 ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES IF YOU ARE UNFAMILIAR WITH WIRING YOU SHOULD USE A QUALIFIED ELECTRICIAN 1 TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT USE A SOLID STATE SPEED CONTROL WITH THIS FAN USE HUNTER CONTROL MODEL 22691 2 TO REDUCE THE RISK OF PERSONAL INJURY DO NOT BEND THE BLADE BRACKETS WHEN INSTALLING THE BRACKETS BALANCING THE BLADES OR CLEANING THE FAN DO NOT INSERT FOREIGN OBJECTS IN BETWEEN ROTATING FAN BLADES PRE INSTALLATION INSTRUCTIONS A SELECT INSTALLATION SITE CHECK TO MAKE SURE THAT IN NORMAL USE NO OBJECT CAN COME IN CONTACT WITH THE ROTATING FAN BLADES THE MOUNTING SITE SHOULD ALSO MEET THE PRECAUTIONS LISTED IN STEP 3 BELOW B INSTALLATION HARDWARE IS INCLUDED FOR A STANDARD DRYWALL OR PLASTER CEILING YOU WILL NEED A 4 X 1 1 2 OR 4 X 1 2 OUTLET BOX AND WIRE NUTS 2 WHICH CAN BE PURCHASED FROM ANY HARDWARE STORE OR ELECTRICAL SUPPLY HOUSE C THE FAN BLADES MUST BE MOUNTED AT LEAST 7 ABOVE THE FLOOR FOR MAXIMUM EFFICIENCY THEY SHOULD NOT HAVE ANY OBSTRUCTION WALLS POSTS ETC WITHIN 24
5. CED BLADES 2 FAN TOO CLOSE TO VAULTED CEILING 3 LOOSE BLADES OR BLADE BRACKETS 4 FAN NOT SECURE ON HANGER ASSEMBLY 1 USE BALANCING KIT SEE STEP 8C 2 LOWER OR MOVE FAN 3 TIGHTEN ALL SCREWS 4 TURN POWER OFF SUPPORT FAN VERY CAREFULLY LOOSEN CANOPY AND HANG CORRECTLY WHEN SWITCHING FROM MEDIUM TO LOW SPEED YOU MAY NOTICE SOME FAN WOBBLE WHEN FAN SPEED STABILIZES AT LOW SPEED WOBBLE WILL DISAPPEAR IF YOU HAVE CHECKED THE ABOVE PROBLEMS AND STILL HAVE TROUBLE CALL 901 745 9222 HUNTER FAN COMPANY 2500 FRISCO AVENUE SINCE 1886 MEMPHIS TN 38114 REV 5 94 FORM NO 40987 01 PAGE 5 1989 HUNTER FAN COMPANY
6. EWS PREVENT THE NIPPLE FROM WITH LOCKWASHERS PACKAGED WITH THE UNSCREWING ADAPTOR KIT MAKE CERTAIN THE SCREWS B BEING CAREFUL NOT TO SCRATCH ARE TIGHT FAILURE TO DO SO COULD THE CANOPY FINISH HANG THE RESULT IN THE FAN FALLING FAN FROM THE HOOK IN THE CEILING CAUTION TO ENSURE PROPER ENGAGEMENT OF THE PLATE USING ONE OF THE 3 SLOTS CANOPY ASSEMBLY SCREWS THE CANOPY IN THE CANOPY SEE FIGURE 5A MUST FIT SNUG AGAINST THE TOP OF THE NOTE FOR MOUNTING FAN ON VAULTED FAN CEILING THERE ARE 2 SETS OF HOLES CAUTION DO NOT LIFT MOTOR BY WIRES ON THE SIDE LOCKING TAB IN SIDE FORM NO 40987 01 PAGE 2 MUST BE IN UP POSITION USE SET OF HOLES IN CEILING PLATE THAT ASSURES LOCKING TAB IN CANOPY IS IN THE UP POSITION C BEING CAREFUL NOT TO SCRATCH THE CANOPY FINISH HANG THE FAN FROM THE HOOK IN THE CEILING PLATE USING ONE OF THE 3 SLOTS IN THE CANOPY SEE FIGURE 5A REV 5 94 SCREWS WITH LOCKWASHERS AND LOCTITE ON THREADS LEAD WIRES CANOPY SCREW HEAD GROUND WIRE PIPE NIPPLE BALL CEILING PLATE ADAPTOR 6 MIN CEILING CANOPY SCREW HOLE PLATE HOOK PIPE NIPPLE FAN ASSEMBLY CANOPY iPENIBBPE SETSCREW TIGHTEN SECURELY MOTOR FIGURE 5 FIGURE 5A FIGURE 5B STEP 6 FINAL WIRING A CONNECT ELECTRICAL SUPPLY LEADS TO THE LEADS FROM MOTOR USING APPROVED CONNECTORS CONNECT BLACK ELECTRICAL SUPPLY LEAD TO THE BLACK MOTOR LEAD AND THE BLACK WITH WHITE STRIPE MOTOR LEAD SEE NOTE CONNEC
7. F THE WOODSCREWS 5 64 AND USE TWO 8 X 1 1 2 WOODSCREWS AND WASHERS USE THE INNERMOST HOLES FOR SECURING THE BOX ORIENT THE BOX SO THE OUTERMOST HOLES ARE ALIGNED WITH THE 2 X 4 BRACE THE OUTERMOST HOLES WILL BE USED IN STEP 4B DO NOT USE A LUBRICANT ON SCREWS B BRING ELECTRICAL CABLE INTO THE OUTLET BOX AND ATTACH WITH AN APPROVED CONNECTOR MAKE CERTAIN THAT WIRING MEETS ALL NATIONAL AND LOCAL ELECTRICAL CODES WIRE LEADS SHOULD EXTEND AT LEAST 6 BEYOND OUTLET BOX FOR EASE IN MAKING CONNECTIONS SEE FIGURE 3 REV 5 94 FORM NO 40987 01 PAGE 1 2 X 4 WOOD BRACE CEILING JOIST 8 WOOD SCREW amp WASHER 2 REQUIRED FIGURE 2 CEILING CONNECTOR OUTLET BOX 6 MIN LEAD LENGTH FIGURE 3 STEP 4 INSTALLATION OF THE CEILING PLATE A INSTALL THE 3 RUBBER BUSHINGS INTO THE TOP OF THE CEILING PLATE BY INSERTING SMALL SIDE OF THE BUSHING INTO THE THREE HOLES IN THE CEILING PLATE SEE FIGURE 4A NOTE WHEN ATTACHING CEILING PLATE TO THE OUTLET BOX SUPPORT MAKE CERTAIN BUSHINGS REMAIN IN PLACE NOTE TIGHTEN THE CEILING PLATE MOUNTING SCREWS ONLY ENOUGH TO PROVIDE SLIGHT COMPRESSION OF THE BUSHINGS DO NOT OVER TIGHTEN B THREAD THE LEAD WIRES THROUGH THE OPENING IN THE CEILING PLATE AND INSTALL THE CEILING PLATE TO THE 2 X 4 BRACE WHICH SUPPORTS THE OUTLET BOX USE 2 10 WOODSCREWS 3 LONG AND 2 FLATWASHERS FOR MOUNTING DRILL 2 PILOT HOLES FOR THE MOUNTING SCREWS 9 64 DIAMETER SEE FIGURE 4B re 2 X 4W
8. OOD BRACE BUSHING iy OUTLET BOX FLAT WASHERS CEILING PLATE kie CEILING PLATE a MOUNTING SCREWS FIGURE 4A FIGURE 4B NOTE ASSEMBLY METHODS FOR INSTALLER S CHOICE HANGING SYSTEM YOUR NEW HUNTER FAN CAN BE HUNG IN 2 DIFFERENT MANNERS ONE BEING AS A LOW PROFILE FAN AND ALSO AS A BALL TYPE HANGING FAN THUS INSTALLER S CHOICE CUSTOMER SHOULD READ STEPS 5 THROUGH 7 AND DECIDE WHICH STYLE OF MOUNTING TO USE STEP 5 FAN ASSEMBLY LO PROFILE FAN HANGING FAN A THE CANOPY HAS 4 HOLES IN THE CAUTION DO NOT LIFT MOTOR BY WIRES BOTTOM THE LARGE CENTER HOLE FITS A INSERT PIPE NIPPLE THROUGH OVER THE ADAPTOR ON TOP OF THE FAN CANOPY AND FEED WIRES FROM TOP THE 3 REMAINING HOLES ARE FOR THE OF MOTOR THROUGH PIPE NIPPLE CANOPY ASSEMBLY SCREWS PLACE THE SCREW PIPE NIPPLE INTO FAN UNTIL CANOPY ON TOP OF THE FAN AND ALIGN TIGHT AT LEAST 4 1 2 TURNS THE PROPER HOLES SEE FIGURE 5 MAKE THE SETSCREW LOCKING THE PIPE CERTAIN YOU HAVE LOCATED THE HOLE NIPPLE TO MOTOR MUST BE PATTERN BY CHECKING TO SEE THAT THE TIGHTENED VERY SECURELY SEE CANOPY SITS FLAT ON TOP OF THE FAN FIGURE 5B FAILURE TO TIGHTEN WITHOUT A SPACE BETWEEN THE BOTTOM SCREW COULD RESULT IN FAN OF THE CANOPY AND THE TOP OF THE FAN FALLING IF A SPACE IS PRESENT ROTATE THE CAUTION THE PIPE NIPPLE HAS A SPECIAL CANOPY SLIGHTLY ELIMINATING THE SPACE COATING ON THE THREADS DO NOT B NEXT SECURE THE CANOPY TO THE TOP REMOVE THE COATING IS TO HELP OF THE FAN USING 3 10 32 SCR
9. T THE WHITE ELECTRICAL SUPPLY LEAD TO THE WHITE MOTOR LEAD CONNECT THE GROUND WIRE TO THE GREEN LEADS FROM THE MOTOR AND CEILING PLATE SEE FIGURE 6 GREEN GROUND WIRE CEILING PLATE FIGURE 6 NOTE IF A SEPARATE WALL SWITCH WILL BE USED TO CONTROL THE LIGHT CONNECT THE BLACK WIRE WITH WHITE STRIPE TO THE WALL SWITCH LEAD THE WALL SWITCH MUST BE ACCEPTABLE FOR USE AS A GENERAL USE SWITCH CAUTION NO BARE WIRE OR WIRE STRANDS SHOULD BE VISIBLE AFTER MAKING CONNECTIONS B AFTER MAKING THE WIRE CONNECTIONS THE WIRES SHOULD BE SPREAD APART WITH THE WHITE AND GREEN WIRES ON ONE SIDE OF THE OUTLET BOX AND THE BLACK AND BLACK WHITE WIRES ON THE OTHER SIDE OF THE BOX THE SPLICES SHOULD BE TURNED UPWARD AND PUSHED CAREFULLY UP INTO THE OUTLET BOX STEP 7 FINISH FAN ASSEMBLY A THE CEILING PLATE HAS 3 MOUNTING SCREW HOLES LOCATED ON THE SIDE INSTALL 3 10 32 X 1 2 PHILLIPS ROUND HEAD SCREWS HALFWAY INTO THESE HOLES SEE FIGURE 7 REMOVE THE FAN FROM THE CEILING PLATE HOOK MAKE SURE NOT TO BREAK ANY WIRE CONNECTIONS THE CANOPY HAS 3 MATING SLOTS SEE FIGURE 7 LEAD WIRES CEILING PLATE CANOPY GROOVE IN BALL PIPE NIPPLE CANOPY FOR HANGING FAN CONFIGURATION ROTATE BALL UNTIL GROOVE IN BALL MOUNTING SLOTS 3 ENGAGES TAB IN CANOPY FIGURE 7 FIGURE 7A B POSITION 3 SLOTS IN CANOPY DIRECTLY UNDER AND IN LINE WITH 3 MOUNTING SCREWS IN CEILING PLATE LIFT FAN UNTIL CEILING PLATE MOUNTING SCREWS 3 ARE SEA
10. TED IN BOTTOM OF SLOTS IN CANOPY ROTATE FAN COUNTERCLOCKWISE UNTIL ALL 3 MOUNTING SCREWS DROP INTO SLOT RECESSES TIGHTEN 3 SCREWS SECURELY CAUTION FAILURE TO SECURELY ASSEMBLY THE CANOPY SCREWS COULD RESULT IN THE FAN FALLING NOTE FOR THE HANGING FAN CONFIGURATION ROTATE FAN UNTIL GROOVE IN BALL IS POSITIONED OVER TAB IN CANOPY MAKE CERTAIN GROOVE AND TAB ARE ENGAGED BEFORE RUNNING FAN SEE FIGURE 7A FAILURE TO DO THIS COULD RESULT IN THE FAN FALLING REV 5 94 FORM NO 40987 01 PAGE 3 STEP 8 FAN BLADE ASSEMBLY INSTALLATION AND BALANCING A ATTACH WOOD BLADES TO BLADE BRACKETS USING THREE SCREWS FOR EACH BLADE SEE FIGURE 8 ASSEMBLE THE BLADE TO THE BLADE BRACKET MAKE SURE ALL SCREWS ARE TIGHT TO PREVENT VIBRATION OR WOBBLING BLADES SHOULD BE MOUNTED FLAT AGAINST IRONS WITH THE BOSSES POSITIONED ON THE OPPOSITE SIDE OF THE BLADE IRON SEE FIG 8 CLEARANCE HOLES BLADE BLADE BRACKET FIGURE 8 FIGURE 8A B WORKING THROUGH THE LARGE CLEARANCE HOLES IN THE LIGHT SWITCH HOUSING REMOVE THE SCREWS SCREWS FROM THE MOTOR HUB INSERT A MOUNTING SCREW PROVIDED IN HOLE IN BLADE BRACKET USE A SCREWDRIVER TO HOLD IN PLACE ALIGN BLADE HOLES WITH MOUNTING HOLES IN HUB BY TURNING SCREW AND READJUSTING BLADE BRACKET UNTIL SREW MATES WITH THREADED HOLE IN HUB DO NOT TIGHUTEN UNTIL BOTH SCREWS HAVE BEEN PUT IN BLADE BRACKET REPEAT FOR ALL BLADES ROTATING MOTOR HUB AS NEEDED TO EXPOSE MOUNTING HOLES SEE FIGURES 8A AND 9
Download Pdf Manuals
Related Search