Home

Humax IR-5410Z User's Manual

1. 5 After the above mentioned value is set press the OK button to start Service Search Note The picture and the found service list during Advanced Search are identical with the ones during Manual Search SMATV Search In case that several generations use Antenna and LNB in common as the frequency range of signal is input to STB is down as much as LNB L O Local Oscillator frequency search the service from 950 2150MHz Frequency Inputs not RF frequency but the frequency that is down converted through LNB in common The unit is MHz and the range of input is 950 2150MHz Symbol Rate Inputs the Symbol Rate of the signal you want to find FEC You can select the value of 1 2 2 8 3 4 5 6 7 8 or Auto LNB Power As there is whether the LNB Power of STB is necessary or not according to the sort of IF IF converters select a suitable option for situation GB33 Automatic Search When you enter the Satellite Name that is set in Antenna Setting menu search all of the selected satellite without inputting the extra frequency Antenna Alternative Select the target antenna for Automatic Service Search The attribute of this antenna alternative number is already set in Antenna Setting menu and the Satellite Name is helpful in the selection of the antenna but in this menu you cannot change the Satellite Name Search Type You can select one of two modes Quick or Detail When you select Quick mode
2. 1 To display the Service All press the OK button Use RED CD button to select the All service list 2 Select the desired service by using the 4 buttons 3 Press the OK button to view the selected service The service list provides you the Simple mode and Advanced mode The right side scroll bar of the screen displays the location of the selected service in relation to All services Press the RED CD button to toggle between Simple mode and Advanced mode GB16 Guide of Main Menu Service Favourite 1 Press the GREEN C gt button on the remote control unit to select the Favourite service list Note The groups are labeled in four different alphabet characters A B C D 2 Use the A Y buttons to select a favourite group that you want 3 Press the GREEN button to toggle group and service list Service Network 1 Press the YELLOW Ca button on the remote control unit to select the Network service list 2 Use the A Y 4 buttons to select a service 3 Press the YELLOW C2 button to toggle provider and service list Note 1 The provider name is displayed on the left window and the provider s services are displayed on the right window 2 The scroll bar on left of the screen shows the location of the cursor in the Network The scroll bar on right of the screen shows the location of the service from the selected Network Service Genre 1 Press the BLUE Ga button on the remote control unit
3. Audio Output Set the audio mode which is output from the RCA Cinch Jack or SCART Stereo Mono Dolby Digital If Dolby Digital option is ON and the broadcaster provides the Dolby Digital stream the Dolby Digital audio language is firstly selected when changing the service Screen Mode Select the aspect ratio of TV which is connected to STB 4 3 or 16 9 Display Format Select the format which the video is to be displayed on screen When your TV set is 4 3 and video source is 16 9 STB will display in Letter box or Centre mode as selected When your TV set is 16 9 and video source is 4 3 STB will display in the Pillar box or Full mode as selected NTSC Mode Adjust this value between 3 58 and 4 43 if your TV displays the video only in black and white color Normally NTSC 3 58 mode is used worldwide but some TV sets can support only NTSC 4 43 mode GB22 Guide of Main Menu UHF Tuning You select the STB output by using the UHF channel Channel Select an UHF channel The range of channels and frequency value are different for each PAL Standard PAL I G for Europe CH21 CH69 PAL B for Europe Australia CH28 CH69 PAL D for China CH13 CH62 PAL K for Russia CH21 CH69 PAL Standard Select a PAL Standard according to the above range of channels Offset Adjust the fine tuning value The Offset ranges from 4 to 4 and each Offset represents 1MHz GB23 Other Setting Select
4. Digital Set Top Box with Irdeto Embedded IR 5410Z IR 5410Z User s Manual m Specifications are for IR 5410Z models HUMAX your prime time Contents Safety GB2 Copyright amp Glossary rire GB3 Reference GB4 STB Connections GB5 GB10 Remote Control Unit GB11 pe GB12 Guide of Functions GB13 GB14 Guide of Main Menu GB15 GB36 Motorised System GB37 Ni GB40 Troubleshooting Guide GB41 GB42 Menu Map GB43 As GB44 Specification GB45 GB46 GB1 Safety This STB has been manufactured to satisfy the international safety standards Please read the following safety precautions carefully MAINS SUPPLY OVERLOADING LIQUIDS CLEANING VENTILATION ATTACHMENTS 190 250 V AC 50 60 Hz Do not overload a wall outlet extension cord or adapter as this may result in fire electric shock The STB shall not be exposed to dripping or splashing and that no objects filled with liquids such as base shall be placed on the apparatus Disconnect the STB from the wall outlet before cleaning Use a light damp cloth no solvents to dust the STB The slots on top of the STB must be left uncovered to allow proper airflow to
5. Channeli CH21 69 CH28 69 or CH13 62 for the Remodulator Standard PALI G B DKK selectable by Menu setting Preset Channel CH36 or TBD Software changable by Menu Power Supply Input Voltage 190 250V AC 50 60 HZ Type SMPS a Power Consumption Max 350 Standby Power 10 Protection Separate internal fuse The input shall have lightening Protection Physical Specification Size W xH x D 370 x 60 x 280 mm Excluding the Foot OOt height is 8 MM css Weigh Ne n Around28kg 1 Operating Temp 0C to 45 Storage Temp 10 C to 70 C Ee Storage Humidity 5 95 RH Non Condensing You can use a special antenna switch with DiSEqC commands When changing ASTRA1 to EUTELSAT for example a DiSEqC command is sent with the 22KHz tone through the antenna cable The antenna switch will change ASTRA1 to EUTELSAT The concept of DiSEqC is a protective trademark of EUTELSAT Data rate decides the picture quality of digital TV programmes Data rate of about 5 6 Mbit s coincides with the picture quality of a analog TV programme GB46 www humaxdigital com HOIR54102 200GB
6. STB is switched on see above Check the video output port RCA RF or SCART is firmly connected to the TV or VCR If you are using the RF Output check that the RF Lead is connected firmly to the STB and TV VCR Check that you have selected the correct channel or Video Output on your TV If you are using the RF Output check that you have correctly tuned the UHF channel of the STB or TV Check the brightness level of the TV Poor picture quality See No Picture above Check the signal level if this is low then try adjusting the alignment of your dish No Sound See No Picture above Check the volume level of the TV and STB Check the Mute status of the TV and STB Remote Control does not operate Point remote control directly towards the STB Check and replace batteries On Screen Error Messages No or Bad Signal Check the LNB replace LNB if necessary Check the cable from the LNB Check the position of the dish realign dish if necessary If you are using a DiSEqC 1 0 switch check that you have connected the LNBs to the correct connections on the switch Check the Signal Level and the Signal Quality in the Signal Status menu Service is not running or scrambled No access to the service slot GB41 Check whether the Smart card is correctly inserted Check whether the Smart card is appropriate for the selected service Problem Solution Time Display The front
7. Shift Keying QPSK Phase shift keying in which four different phase angles are used Service A channel to which a decoder or TV is tuned Transponder An automatic device that receives amplifies and retransmits a signal on a different frequency GB3 Reference 1 Connect DiSEqC 1 0 All our receivers are designed to be DiSEqC 1 0 compatible This allows multiple antennas to be connected to the STB simultaneously If you have two or more fixed antennas or LNBs you can use a DiSEqC 1 0 switch 1 Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch 2 Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input connector of the DiSEqC switch 3 Do the same for other LNBs 4 Connect one end of a Coaxial cable to the RF output connector of the DiSEqC switch and the other end to the LNB IN socket on the STB 2 Connect DiSEqC 1 2 Please refer to page GB37 3 Connect a Satellite antenna To the digital receiver you can connect either a single satellite antenna directly or through converter box several antennas or LNB of multi feed equipment You can connect a further Sat receiver for example analogue with the receiver of common antenna equipment that has satellite signals Connect an antenna cable through converter boxes 1 When you assemble several antenna or a multi feed equipment that has several LNB or LNB with several exits connect each cable from the
8. change services down up Rear Panel IR 5410Z IR 5410Z Eisen N tans vot 9 so mama E 4 C nsumption 35W Ei Power supply 190 250V 50 60Hz power cor LNB IN Use to connect an antenna LNB OUT Use it when connecting to another STB Rs 232C Use it when connecting to your PC AUDIO VIDEO OUTPUT Audio video signal from your STB to VCR or TV RF INPUT Use to connect a general Aerial Antenna and CABLE jacks to a RF input jack on the STB RF OUTPUT Use to connect a RF signal from your STB to RF ANT input jack on your TV S PDIF Output for connection to a digital amplifier TV SCART For the audio video input of the TV VCR SCART For the VCR GB6 STB Connections IR 5410Z There are several ways of connecting the STB to your existing Audio TV system We recommend using one of the following set up for best results 4 GB7 TV only 1 Connect one end of a RCA cable to the RCA connector on the STB and the other end to a RCA socket on your TV Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN connector on your TV Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels Connect the coaxial cable from the LNB to the LNB IN socket on the STB TV with VCR 1 Connect one e
9. feature allows the user to Delete Lock Skip Rename a service in the selected Genre Available genre Movie News Show Sports Children Music Art Education etc The colour buttons function same as ones for Organise All services except the following differences When you delete a service in the selected genre it will be available again on the All TV services list at the right side At that time the genre for the deleted service becomes etc You can move the service only in the selected genre Coloured buttons are available when the cursor is located in the middle window To select the Genre 1 Use the lt button to move the cursor to Gr plate left 2 Select the wanted genre To group the services into a Genre 1 Use the button to move the cursor to Services plate right 2 Select the service you want to group into Genre 3 Press the OK button 4 Use the lt button to move the cursor to Genre plate left 5 Press the OK button to save the selected group Note 1 Use the lt gt buttons to move the cursor 2 Use the buttons to select the previous or next page dada E rk Organise Radio Services The Organise Radio Services functions same as TV Services excepl that it uses Radio Services You can delete or move Radio Services and change the attributes of them Organise Services The Organise All Services lets the user Delete Move Lock Skip or Rename Radio
10. firstly display the service list using OK button Use A Y 4 buttons to select a service and press OK button Also use amp buttons to select a service directly in the service list The contents of service list are as follows Simple Service List 1 Use the A Y buttons to select Select Service from the Main Menu and press the OK button 2 Use the A Y buttons to select Simple from the Main Menu and press the OK button 3 Then the simple service list will appear on the screen Advanced Service List The advanced service list shows thirty services This list is similar to the Simple service list except that it shows thirty services and is apart from the Network and Genre list that displays twenty servies Use the following colour buttons to list various service lists The colour button corresponds the following Service List RED CD button service list All GREEN C button Favourite YELLOW button Network BLUE Genre WHITE button service list by Alphabetical order Service Configuration To change the attributes of a service 1 Use the A Y 4 buttons to move a service you want to change in the Service List 2 Press the MENU 9 button 3 Use the A Y buttons to move to an item such as genre favourite lock skip delete you want on the Service Configuration screen 4 Use the lt gt buttons to select Press the OK button to complete Service
11. on the I plate GB14 Guide of Main Menu 1 Select Service The select service displays the required service list which can be viewed in Simple or Advanced mode 2 TV Guide Your STB has an Electronic Programme Guide EPG to help you navigate through all the possible viewing options The TV Guide supplies information such as programme listings and start and end times for all available services In addition detailed information about the programme listings and start and end times for all available services In addition detailed information about the programme is often available in the EPG the availability and amount of these programme details will vary depending on the particular broadcaster 3 Parental Control Access to services and programmes is controlled by a PIN code i e a 4 digit secret code that is defined by the user The very first time you attempt to lock all services or lock programmes by ratings the on screen menu will instruct you to assign a PIN code Later on if necessary you can change it 4 Installation The Installation mode allows you to have the information of setting services and newly set services language time organise search Furthermore you can recognize the states of hardware and software versions and signals from your STB 5 Utility This menu provides Calendar and Biorhythm GB15 1 Select Service To select the desired in the service list you should
12. on the screen The HELP window shows the current Network information including Satellite Name Frequency Polarisation Symbol Rate FEC The detailed information for the event can be displayed by pressing the HELP button in the I Plate with event data displaying mode You can reserve the programme in the event data display mode by using the WHITE Cc button You can reset timer programme Once Daily or Weekly mode When you release the timer programme mode then you will be asked to confirm the action Changing Services To change services do in the following sequence 1 Press the NUMERIC buttons 0 9 on the remote control unit 2 Press the 2 62 buttons or A Y buttons Or press the RECALL amp Service list 69 EPG mode button To switch between TV and Radio services press the TV Radio button To select the previous viewed Service press the RECALL button GB13 Volume Control To adjust the volume level use the buttons or lt gt buttons To temporarily stop the volume press the MUTE cGo button To cancel mute press the MUTE button again or press the buttons or lt gt buttons Soundtrack When you want to change the audio language of current service press the GREEN button firstly The on screen menu is displayed on the top to left side of the screen To change the audio language 1 lt gt buttons Use to select the audio on the
13. panel does not display the time Make sure you have switched on the STB Switch the STB on and tune to a service to allow the STB to receive the time sent with the signal by the service provider Front panel will only display the time in Standby mode Time displayed on the front panel is incorrect Adjust the time in the Time Settings menu Service Search No Signal in Manual Search Check the Signal Level and the Signal Quality in the Signal Status menu Check the LNB replace LNB if necessary Check the cable from the LNB Check the position of the dish realign dish if necessary DiSEqC 1 0 Check that you have connected the LNBs to the correct connections on the switch Check that you have set the correct settings in the Antenna Setting menu DiSEqC 1 2 Check that you have selected this in the Antenna Setting menu Check that the dish is aimed at the correct satellite e f you can t solve the problem even referring this Troubleshooting Guide contact us via our homepage Homepage http www humaxdigital com GB42 GB43 Menu Map MAIN MENU Select Service Advanced Language Setting Menu Language Audio Language Subtitle Language Current Time Timer Timer Mode Wakeup Time Wakeup Service No Sleep Time Video Output Audio Output Dolby Digital Screen Mode Display Format NTSC Mode Channel OSD Transparency PAL Standard Offset Other
14. 50 9750 10600 10750 11475MHz or 0 1 9 3 If the required LNB Frequency is not available then select 0 and enter the frequency manually using the NUMERIC buttons 0 9 4 When you select Universal both 9750 and 10600MHz are supported at the same time The 22KHz Tone setting is unnecessary Disabled 22KHz Tone When you use a dual LNB or two antennas connected to a 22KHz Tone switch box make 22KHz Tone switch enable or disable to select LNB or antenna DiSEqC Input According to the option and position of DiSEqC switch select Disabled Tone Burst A to B and DiSEqC A to D After setting the above mentioned value press the OK button to move to the Manual Search menu Motorised System The Motorised System is used to set the DiSEqC 1 2 motor by Eutelsat specification If you wish to use this system please refer to page GB37 GB30 Guide of Main Menu Service Search OSD If you press the EXIT button during the search then Service Search stops and the searching menu will appear When you find all the services the following picture appears Before saving it you can select the services you want to delete Found services OSD The picture above shows services that are found after Manual Search e Use the RED CD button to mark the services that you want to delete To unmark a service select the service and press the RED CD button again Press the OK button to save or press the EXIT butt
15. Cinch stereo cable from the AUDIO L R sockets on the back of the STB to the LINE AUX SPARE OR EXTRA input sockets on your Hi Fi system IR 5410Z SSS S 5 ss with VCR and Motorised System DiSEqC 1 2 1 Connect one end of a 21 pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV 2 Connect one end of a 21 pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR 3 Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN connector on your TV 4 Connect one end of a RF lead to the RF IN connector on your VCR and the other end to the RF OUT connector on the STB 5 Connect the coaxial cable from the LNB of your motorised system to the LNB IN socket on the STB 6 Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels 7 Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1 2 motor GB10 Remote Control Unit NUMERIC BUTTONS INFORMATION RED SOUNDTRACK GREEN SUBTITLE YELLOW UHF BLUE TIME WHITE EXIT V V GB11 STANDBY TV SAT Reserved TV RADIO MUTE MENU CURSOR OK P P HELP EPG RCL Recall NUMERIC BUTTONS Press to select a service enter your PIN code or numeric on the menu INFORMATION RED Press to display the programme information box on the sc
16. IN code in the highlighted Verify Changed PIN code 5 When the entered PIN code is correct then all settings are completed If the PIN code is wrong the message PIN code mismatch will be displayed on the display window When the OK button is pressed at this time the Old PIN code is valid and the cursor is located in the first position of this menu 4 Installation This mode allows you to customise add a new service and displays the state of the STB Enter the submenus after selecting the Installation mode in the Main Menu 4 1 System Setting The System Setting mode supports the STB internal settings according to the connection of the receiver and external units This mode includes Language Setting Time Setting A N Output Setting UHF Tuning and Other Settings Language Setting Select the language for menu audio or subtitle 1 Select the highlighted language setting using the buttons in the system setting mode and then press the OK button 2 Select the highlighted Menu or Audio Subtitle Language and press the lt gt buttons and the language list will be displayed 3 Use the A Y buttons to move to a language you want and then press the OK button to finish setting Menu Language We support the various menu languages of Europe amp Middle East areas For Europe areas there are Czech Danish English French German Greek Hungarian Italian Portuguese Spanish Swedish Turkish and more Als
17. Parema Tu Gma URe Organise Favourite A D Each of TV and Radio has four Favourite groups Each Favourite group contains up to 100 services Delete Move Lock Skip or Rename each TV service in a Favourite TV group and re group them into your Favourite TV group This mode has the same operating methods as Organise All Services When you delete a service in the Favourite group it will be available again on the All TV service list This allows the service to be removed from the Favourite group You can move the service only within the Favourite group Coloured keys are available when the cursor is located in the middle window Except when the middle window is disabled grey To select the Favourite group 1 Use the lt button to move the cursor to Gr plate left 2 Select the wanted favourite group To group the services into Favourites 1 Use the button to move the cursor to Services plate right 2 Select the service you want to group into Favourites 3 Press the OK button 4 Use the lt button to move the cursor to Favourites plate left 5 Press the OK button to save the selected group Note 1 Use the lt gt buttons to move the cursor 2 Use the 2 buttons to select the previous or next page GB26 4 panine GB27 Guide of Main Menu P r Genre ci T ie um oT FE Ld s A Organise Service Genre The Organise Service Genre
18. Press the OK button anywhere to start Automatic Search The picture during searching is as follows The picture searches with varying Frequency Symbol Rate and FEC etc Satellite Name is the name that the user selects to correspond with Antenna Alternative of Antenna Setting The progress bar appears on bottom of the picture During the search services that are found are displayed as follows 1 Press the EXIT button during Automatic Search to stop search 2 After the search is finished the appearite message appears 3 Press the OK button to return Service Search menu 4 4 Status STB Status Displays the information of H W Version S W Version and Loader Version of STB and so on Signal Detection Shows the Signal Level AGC level and Signal Quality BER of the current service and is help to the initial antenna setting GB35 4 5 Conditional Access for Irdeto Embedded This menu allows the user to view the information on the Smart Card and Irdeto Conditional Access system such as version nationality and serial number of smart card and messages Version Information The version of SoftCell means that of Irdeto Conditional Access software You can see the version of conditional access hardware and Euro I Chip at this menu Smart card Information You can see the version nationality and serial number of the Smart card Addressed Messages You can see and store the newest five messages arrived Note Whe
19. Setting Info Box Display Time Changing to Reserved Service Menu Background TV Guide Service Organising Organise Services Organise Favourite A D Organise Service Genre Organise TV Services Organise Services Organise Favourite A D Organise Service Genre Organise Radio Services Organise Networks Specifications are for IR 5410Z models Installation Utility Calendar Biorhythm Service Searching Status Conditional Access Antenna Setting Antenna Alternative STB Status Version Information Signal Detection Smart card LNB Frequency Information 22KHz Tone DiSEqC Input Motorised System Addressed Messages Manual Search Antenna Alternative Frequency Polarisation Symbol Rate FEC Network Search Automatic Skip Advanced Search Antenna Alternative Frequency Polarisation Symbol Rate FEC Video PID Audio PID PCR PID SMATV Search Frequency Symbol Rate FEC LNB Power Automatic Search Antenna Alternative Satellite Name Search Type GB44 GB45 Specification Conditional Access Interface Irdeto Embedded 1 Slot Smart card Tuner amp Channel Input Connector F type IEC 169 24 Female Frequency Range 950 2150 MHz Input Impedance 75 Q unbalanced Signal Level 25 to 65 dBm IF 480 MHz IF Band width 36 MHz LNB Power amp Vertical 13 5 V Polarisation Horizontal 18 V Current 500 mA Max Overload Protection 22 KHz Tone Frequen
20. The time setting will be used as the standardised time for the I Plate TV Guide Wakeup and Sleep Timer Time Offset Current Time is based on TDT Time and Data Table at the stream of the current service Timer You can select nine kinds of Timer like 1 2 8 and Disabled If you select Disabled then the other timers will not work Press the OK button at timer option to display the Timer table The Timer determines the on off time and can also be used for VCR recording Timer Mode Wakeup Sleep timer determines the Timer Mode e Once The timer programming is applied only once Daily The timer recording is applied everyday repeatedly Weekly The timer recording is applied weekly Set one day in a week Use the lt gt buttons to select the type of timer programming Wakeup Time Select the time when STB is turned on Use the NUMERIC buttons 0 9 on the remote control unit to enter your Wakeup Time Wakeup Service No Use the lt gt buttons to set the service number provided for the set Wakeup Time Use the TV Radio G gt button on the remote control unit to toggle TV Radio service Service Name The Service Name that has been determined by the Wakeup Service No will be shown Sleep Time Depending on Time Setting select the time when STB is turned off GB21 A V Output Setting Video Output CVBS S Video RGB Set the video mode for the TV SCART output Specifications are for IR 5410Z models
21. Use the lt gt buttons to select the Forward Error Correction of the transponder You can select the value of Auto 1 2 2 3 3 4 5 6 and 7 8 Network Search You can select Yes or No When you select Yes you can find more transponders using the home network As it refers to NIT during searching if there is the frequency information of other transponder it searches the other transponder besides the transponder that the user inputs Automatic Skip You can select Yes or No When you select Yes the search will skip all scrambled services When the found services are scrambled during searching they are not listed up Refer to descriptor of PMT whether it is scrambled or not GB32 Guide of Main Menu Advanced Search Performs a manual search with the ability to enter PID Video Audio PCR values This mode is necessary when you search for the signal that has abnormal service Infornation tables The setting of the sub items is the same as Manual Search Video PID Audio PID PCR PID You can set PID to search for services 1 Use the lt gt buttons to select PID input mode 2 Use the NUMERIC buttons 0 9 buttons on the remote control unit to enter a decimal PID value 3 In the hexadecimal input mode press one of the NUMERIC buttons 0 9 to display a hexadecimal keyboard 4 Enter a hexadecimal PID value Note If no PID is input Auto is displayed the Advanced Search functions same as Manual Search
22. antenna to a converter box 2 Connect the output of converter box to LNB IN as in example displayed 3 For converter boxes of 22KHz or DiSEqC steerage you can skip this point because the steerage signal occurs through the antenna cable 4 Loop Through If you have another analogue or digital STB and you wish to use the same LNB then you can connect it via the loop through Connect one end of a Coaxial cable to the LNB OUT on the STB and connect the other end to the LNB IN on your second STB 5 Connect a S PDIF Fiber Optic cable If you are watching a programme with a Dolby Digital soundtrack see page GB14 you can enjoy the higher quality sound of the Dolby Digital audio by connecting the STB to an external Dolby Digital television or amplifier Do this by connecting the optical S PDIF output of the STB to the optical S PDIF input of the external Dolby Digital product television amplifier GB4 GB5 STB Connections Front Panel IR 5410Z Q 18 54102 IR 5410Z o IR 5410Z smwogy W TV LED AMBER The LED lights on in TV mode e RADIO LED GREEN The LED lights on in RADIO mode 6 DISPLAY Shows service number error messages RCU commands and time in Standby mode 4 STANDBY LED RED Indicates that the STB is under standby STANDBY Press to switch between Operation and Standby modes TV RADIO Press to switch between TV and Radio modes Q Use
23. cy 22 4 KHz Amplitude 0 6 0 2 V DiSEqC Control Version 1 0 1 2 Compatible Demodulation QPSK Input Symbol Rate 2 31 Ms s FEC Decode Convolutional Code Rate 1 2 2 3 3 4 5 6 and 7 8 with Constraint Length K 7 MPEG Transport Stream A V Decoding Transport Stream MPEG 2 ISO IEC 13818 Transport stream Specification Profile Level MPEG 2 MP ML Input Rate 15 Mbit s Max Aspect Ratio 4 3 16 9 Video Resolution 720 x 576 Audio Decoding MPEG MusiCam Layer 8 II Audio Mode Single channel Dual channel Joint stereo Stereo Sampling 32 44 1 and 48 KHz Memory Main Processor TMIPS R3930 81MHz Flash Memory 3 Mbyte Graphic MPEG DRAM 4 Mbyte System DRAM 2 Mbyte Please note The specification of the STB may be changed without notice in advance amp Data In Out TV SCART Video Output CVBS S Video RGB Audio Output Resolution 20 bits DAC Max 2 Vrms 2 VCR SCART Video Output CVBS Video Input CVBS S Video RGB Audio Output Resolution 20 bits DAC Max 2 Vrms fixed _ VIDEO RCA Cinch Video Output CVBS 1 AUDIO R L RCA Cinch Volume and Mute Control f s Resolution 20 bits DAC Max 2 Vrms _ mE S PDIF Digital Audio Output Fiber Optic Resolution 20 bits RS 232C Transfer rate 115 200 bps 9pin D sub Type RF Modulator RF Connector 750 IEC 169 2 Male Female Frequency 470 860 MHz Output
24. e Parental Control or Service Organising menu Press the OK button to start Service Search after setting the parameters The default PIN code is Antenna Setting Selects the antenna and LNB settings for Service search As you can change the settings for 22KHz Tone and DiSEqC switch there are 32 possible Antenna Setting for use The values that are set in this menu will be available for selection in other service searching menus Antenna Alternative There are 32 antenna alternatives each one can have different combinations of settings for 22KHz Tone and DiSEqC switch Satellite Name Selects the Satellite Name that corresponds to the value of the Antenna Alternative 1 Press the buttons to display the satellite list box 2 Select the wanted Satellite Name 3 If the desired Satellite Name is not listed then select User Defined 4 The keyboard will appear and you can type the Satellite Name directly The selected Satellite Name can help you select the Antenna Alternative in the searching menu but it is possible to change or select the Satellite Name only in the Antenna Setting menu 5 Satellite Name is listed in alphabetical order and the order can be changed according to Menu Language 6 When inputting the Satellite Name there is a 14 character limit GB29 LNB Frequency 1 Select the L O Frequency that is set to antenna 2 Use the lt gt buttons to select the LNB frequency Universal 51
25. ellite manually Motor Control Search Searches for services on the chosen transponder Goto Moves the motor to the stored position of the selected satellite name Store Stores the current position of the motor for the selected satellite name Reset Resets all stored positions of the motor relative to the 0 position Installer mode only DiSEqC Command Mode Changes the current mode between Installer and User 2 Setting your Receiver for DiSEqC 1 2 You must set your receiver up so that it is ready to use DiSEqC 1 2 To do so do as follows z 1 Press the MENU button to display the Main Menu 2 Select Service Searching option and press OK button to display the Service Searching menu 3 Select Antenna Setting option and press OK button to display the Antenna Setting menu 4 You must set up a separate antenna alternative for each satellite position required 5 Select the name of the satellite you wish to use 6 Select the correct LNB frequency for the LNB you are using 7 Set the Motorised System to Enable using the a lt buttons 8 The option DiSEqC Input Selection should now be disabled This option is used for DiSEqC 1 0 and cannot be used in conjunction with DiSEqC 1 2 Your receiver is now ready to use DiSEqC 1 2 To return to the Main Menu use the EXIT button until you are at the Main Menu a This is required when you first set your receiver up to use DiSEqC 1 2 BLAN and sets the
26. ight programmes can be reserved This programme list includes service name date duration time reservation mode and event name To cancel the Reserved service select a programme you want to cancel using the A Y buttons and then press the WHITE C9 button Shows a simple TV Guide like an Information box This mode shows in the A V playback mode Red vertical line Indicates the current time Black white bar Shows the proceeding state of programme Time range of bar This consists of three blocks by 30 minutes per block 3 Parental Control You can set a parental guidance rating to each programme in this mode 1 When the OK button is pressed after selecting the highlighted parental control on the initial menu screen a display window for entering the PIN code will appear on the centre of screen The default PIN code is 2 Enter the PIN code on the display window If any problem occurs when entering a PIN code you cannot switch to the next mode 3 Set the parental guidance rating of highlighted censorship classification The parental level is given as age based numbers no block 6 10 14 18 and total block Enter the PIN code to unlock or lock programmes 4 To change your PIN code Select the highlighted Old PIN code using the A Y buttons and then enter your Old PIN code Enter a New PIN code in the highlighted New PIN code using the A Y buttons To verify the New PIN code re enter a New P
27. it searches the service by search parameters that is preset When you select Detail mode it searches the service through all field of tuner 950 2150MHz Detail Mode The pre fixed symbol rate list is changed according to Antenna Alternative and Satellite Name If you want to add or change it press the RED Ci button The value of Pre fixed symbol rates can not be editable 22000 27500 The picture of the Symbol Rate Add Change mode is as follows 1 When you press the button after entered to detail mode from search type yellow box will be trimmed with red edges meaning edit is possible 2 You can easily put optional value with using NUMERIC buttons 0 9 3 Press the RED CD button for confirmation and you will successfully exit from input mode If press the OK button at symbol rate value input mode the value will be confirmed and if you moves left or right column use the lt gt buttons you can differ values of symbol rate to input Then press the EXIT and the RED Ci button to exit from input mode To delete a Symbol Rate in the above list press the O NUMERIC button in the selected position and then the symbol rate disappears The range of Symbol Rate that is input additionally is 16 30Ms s Note The user should select the Satellite name in Antenna Setting menu When the user types the Satellite Name separately the search type is fixed to the Detail mode GB34 Guide of Main Menu
28. left right or both 2 A Y buttons Use to select the audio language you want 3 OK EXIT button When this button is pressed the Soundtrack OSD will disappear keeping the selected Soundtrack language constant When the current service is switched the audio language returns to the audio language that was selected in previous service If the returned audio language is invalid the audio language that you selected from the audio language menu has the priority of playback Soundtracks broadcast in Dolby Digital are indicated by Dolby Digital symbols either side of the respective language selection in the menu By selecting such a soundtrack the Dolby Digital audio will be output by the optical S PDIF on the STB This can be decoded by an external Dolby Digital television or amplifier for example Subtitle When the current broadcasting programme provides subtitle press the SUBTITLE D button to see the current subtitle language list To change the subtitle language 1 Use the a v buttons to select a Subtitle language you want 2 Press the OK button and the selected language is highlighted and then the Subtitle Language you want is displayed on the screen Press the EXIT button to cancel the Subtitle mode Teletext Use your TV Remote Control Unit to control the Teletext service The teletext button doesn t exist on the STB Remote Control Unit When the service supports Teletext the Teletext icon is displayed
29. n press the OK button and the search will begin 6 When the search has finished press the OK button to view 7 Repeat the process for all the transponders you want from this satellite 8 Automatic Search It is possible to use automatic search using the DiSEqC 1 2 motorised system 1 Ensure that the positions for the satellite you want to search is correct see Section 3 and 5 above 2 In the Main Menu select the option channel searching and press the OK button 3 In the Service Searching menu select the Antenna Alternative that you have set for this satellite 4 When you search new services please refer to Automatic Search of page GB34 5 When the search has finished press the OK button to store and view the services Now that you have stored all the positions of the satellites and searched for all the services you want you can now use your receiver as normal When you change to a service that is being transmitted from a different satellite you will have to wait a few seconds to allow the motor to move into position to receive the new service GB40 Troubleshooting Guide Problem Solution About STB Does not display any message on the front panel or STB has no power Check the main power cable and check that it is plugged into a suitable power outlet Check you have switch the STB main power switch ON at the rear of the STB Check whether STB is in Standby mode No Picture Ensure that the
30. n the messages about conditional access appear on the screen use the amp buttons not the buttons to change services 5 Utility STB supports additional functions such as Calendar and Biorhythm At the Biorhythm use the A Y 4 buttons to adjust your birth year and date to see your current biorhythm status GB36 Motorised system DiSEqC 1 2 User Instructions If you have a DiSEqC 1 2 motorised system then you can use the DiSEqC 1 2 functions available The following instruction describes how to use the DiSEqC 1 2 functions to store the positions of the satellites and to search for the services STAB Rotor Sat motor recommended 1 Satellite Setting Menu Options GB37 When DiSEqC Motorised System is Enabled in the Antenna Setting a new menu is available for configuring the motor This menu is called Satellite Setting and is accessed by pressing the OK button while the option Antenna Alternative is highlighted in the Manual Search menu The following options are available on the Satellite Setting menu Satellite Name A selection of satellite names that can be used to identify a motor position If the satellite name you require is not available please use other In installer mode the Satellite Name Reference refers to the 0 position of the motor Movement In user mode this is used to fine tune the position of the motor for better reception In Installer mode this is used to search for the position of a sat
31. n to store the current position as your West Limit 5 Manual Satellite Search The purpose of this is to set the motor position for each satellite manually This is useful if the satellite you require is not available from the pre programmed list see 3 above To do this you must access the Satellite Settings menu Do as follows GB39 1 2 10 Use the buttons to stop the motor when required 12 11 13 14 Select Service Searching from the main menu and press the OK button to display the Service Searching menu Select the Manual Search option and press the OK button to display the Manual Search menu Select the relevant Antenna Alternative that you are using for this satellite Enter the Frequency Polarisation Symbol Rate and FEC of a transponder on the satellite you wish to find This transponder information should be unique to this satellite Select the Antenna Alternative option and press the OK button to display the Satellite Settings menu Highlight the option DiSEqC Command Mode and using the lt buttons change this to Installer Highlight the option Satellite name and use the buttons to select the satellite you want to find use others if the name of the satellite you want does not appear When you have selected the satellite you wish to find go down to the Movement option and again using the lt gt buttons to start the motor moving You should move the motor as fa
32. nd of a RCA cable to the RCA connector on the STB and the other end to a RCA socket on your TV Connect one end of a RCA cable to the RCA connector on the STB and the other end to a RCA socket on your VCR Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN connector on your VCR Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN connector on your TV Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels Connect the coaxial cable from the LNB to the LNB IN socket on the STB With Hi Fi System 1 Connect an RCA Cinch stereo cable from the AUDIO L R sockets on the back of the STB to the LINE AUX SPARE OR EXTRA input sockets on your Hi Fi system 1 2 B e IR 5410Z SS SSS SS SSS TV with VCR and Motorised System DiSEqC 1 2 Connect one end of a RCA cable to the RCA connector on the STB and the other end to a RCA socket on your VCR Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN connector on your TV Connect one end of a RF lead to the RF IN connector on your VCR and the other end to the RF OUT connector on the STB Connect the coaxial cable from the LNB of your motorised system to the LNB IN socket on the STB Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channel
33. o it includes Arabic English French German Italian Persian Russian Turkish for Middle East areas The kind of languages can be changed depending on the country Languages are subject to change without prior notice Audio Language Select the default language for audio when changing services If you change the current service your STB will initially select the previously memorised Audio Language If the Audio Language of current service is not provided at this time you should reselect a language on the Audio Language menu Languages provided Czech Danish Dutch English Finnish French German Greek Hungarian Italian Norwegian Portuguese Rumanian Russian Spanish Swedish Turkish and more If no language is provided then the default language of current service will be automatically selected Subtitle Language Select the default language for subtitle when changing services Language provided Danish English Finnish French German Greek Hungarian Italian Norwegian Portuguese Spanish Swedish and more GB20 Guide of Main Menu You can set the Current Time and Wakeup Time in this mode Furthermore the Service Number in the Wakeup mode and Sleep Time standby mode can be set When a VCR is connected recording can be automatically done according to Wakeup Sleep Time Setting Current Time To set the Current Time enter the Offset value using the standardised information of current service area
34. o display the reserved programme list BLUE Use to display the simple TV Guide list Quick mode Now Next mode Show the informations of the programmes that are played now or will be played next time This mode consists of the service name event name event duration time current time and on screen display window To watch a programme you want through the display window Use the buttons to select a programme you want The selected service will appear on the right display window Use the A Y buttons to select a programme you want And then press the OK button on the remote control unit The selected service will appear on the right display window The selected OSD will be highlighted every time the cursor moves To reserve a programme you want Select a programme you want by using the 2 2 buttons or A Y buttons And then press the WHITE Ce button Press the lt gt buttons to watch the programme of previous page or the programme of next page Press the YELLOW button to watch the Reserved programme list Weekly mode Shows the information of programmes that will be played for a week Select a day you want using the lt gt buttons To watch and reserve a programme you want do the same steps with the Now Next mode GB18 Guide of Main Menu Die Bde GB19 Reserved mode Shows the programme lists that you have already reserved on the TV Guide or Information box Maximum e
35. of France Telecom CryptoWorks TM is a trademark of Philips Electronics N V Irdeto is a trademark of Mindport BV Nagravision is a registered trademark of Kudelski S A Conax is a trademark of Telenor Conax AS Dolby and the double D symbol are trademarks of Dolby Laboratories Warning HUMAX cannot be held responsible for any kind of problems caused by the use of unofficial software The use of software versions other than HUMAX official software will void the manufacturer s warranty It is advised that only the formal software released from HUMAX should be used in all HUMAX product range Glossary Antenna A device that collects and radiates electromagnetic waves Includes a satellite dish and abroadband antenna Forward Error Correction FEC A system of error control for data transmission Frequency The number of cycles or events per one second which is expressed in the unit of Hertz Hz Intermediate Frequency IF A frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception Low Noise Block LNB Downconverter A low noise microwave amplifier and converter which downconverts a range of frequencies to IF range Packet Identifier PID A set of numbers that idenitifies transport stream packets containing data from a single data stream Polarisation Characteristic of an electromagnetic wave determined by the orientation of the electricfield vector Quaternary Phase
36. on to exit without saving Then Service Search menu appears again When you exit from all menus the first service of the found service list is played In the bottom of found service picture network the information of transponder and the number of found service that the services belong to are displayed The deleted service by the RED Ci button is excepted from counting of the number of services The deleted service is not included in this number Free applies to the empty space of the memory It will be used to store future services GB31 Manual Search Set the search parameters Frequency Symbol Rate etc to manually find the services that you have selected in the transponder The bar on bottom of the submenu shows the signal quality BER of the entered parameters Antenna Alternative Select the target antenna for Manual Search The Satellite Name helps you select Antenna Alternatives This is only for reference and cannot be changed on this menu Frequency Use the NUMERIC buttons 0 9 on the remote control unit Polarisation Use the lt gt buttons to select the Polarisation of the transponder Auto Horizontal Vertical Horizontal 18 V is output through LNB line e Vertical 13 5 V is output through LNB line Symbol Rate Inputs the Symbol Rate of the transponder you want to find Use the lt gt buttons or NUMERIC buttons 0 9 on the remote control unit FEC Forward Error Correction
37. positions of all pre programmed satellites 1 Make sure your motor is installed correctly with the calibrations adjusted for the region you are situated Please consult the user manual for your motor 2 Make sure your receiver is set up to use DiSEqC 1 2 see section 2 above 3 Main Menu select Service Searching option and 3 press the OK button you should now see the Service Searching menu 4 Highlight the option Antenna Alternative and press the OK button to display the Satellite Setting menu 5 Highlight the DiSEqC Command Mode option and use the lt buttons to change the value to Installer and press the OK button 6 Highlight the Motor Control option and use the lt gt buttons to change the value to reset and press the OK button 7 You will now see a warning message press the OK button to continue All motor positions of the pre programmed satellites should now be correct If you have any other make or model of DiSEqC 1 2 motor then you may need to store the satellite positions in yourself Please refer to the user manual for your motor 8 Highlight the DiSEqC Command Mode option and use the lt gt buttons to change the value to User and press the OK button 9 You should now be ready to start storing services for the various satellites see 5 onwards 4 Motor Limit Setting Use this option to set the East and West limits of the motor This should be used to prevent your dish from hitting an
38. ption and press the OK button to display the Satellite Settings menu In the Satellite Settings menu ensure that you have DiSEqC Command Mode option set to User Highlight the option Satellite Name and use the 7 4 buttons to select the satellite you want to view When you have selected the satellite you wish to view go down to the Motor Control option and again using the 4 buttons select go to and press the OK button 7 The motor will now move to the position of the selected satellite 8 The Movement option is used to fine tune the position of the motor 9 When using the Movement option for fine tuning you must remember to store the changes you have made or else these will be lost 7 Searching for services on your selected satellite Once you have moved the motor into position you can search for the channels transmitted from the relevant satellite To search for services on your new selected satellite Do as follows oor WP 1 Move the motor to the position of the satellite you wish to search see section 6 above 2 Select the service searching from the Main Menu and press the OK button To display the Service Searching menu 3 Select the manual search option and press the OK button to display the Manual Search menu 4 Now enter the Frequency and Symbol Rate using the NUMERIC buttons 0 9 Next enter the Polarisation and FEC values using the lt gt buttons 5 When you have entered all these details i
39. r west as possible and the move it east so that you cover the complete movement range of the motor During the move from west to east the Signal Quality bar should register a signal once This is the position of the satellite If there are two or more different positions which registers a signal then you must choose another frequency that is unique to the satellite you want Use the Signal and Strength Quality bar at the bottom of the screen to judge the best position of the dish When you have the best position of the dish go to the Motor Control option and using the buttons select store and press the OK button The position of the satellite should now be stored If you do not store this position it will be lost when you exit the menu Repeat the process for each satellite if required remembering to use a different antenna alternative for each satellite 6 Moving to a pre set Satellite Once you have stored the positions of the satellites you want see left below you can now search for the services transmitted from them Before you can do this you must move the motor to the position of the satellite you wish to search To do this you must access the Satellite Settings menu Do as follows 1 Select Service Searching from the Main Menu and press the OK button to display the Service Searching menu Select the Manual Search option and press the OK button to display the Manual Search menu Select the Antenna Alternative o
40. reen And this button functions same as the RED button on the menus SOUNDTRACK GREEN Press to display the soundtrack list for the current service And this button functions same as the GREEN button on the menus SUBTITLE YELLOW Press to display the subtitle language list for the current service And this button functions same as the YELLOW button on the menus UHF BLUE Press to set the UHF menu This button functions same as the BLUE button on the menus TIME WHITE Press to display the current time on the screen Press to reserve services on the Informaion box or EPG And this button functions same as the WHITE button on the menus EXIT Press to return to the previous menu and screen V V Volume up down buttons Press to increase or decrease the volume STANDBY Press to switch between Operation and Standby modes M TV SAT Reserved TV RADIO Press to switch between TV and Radio modes B MUTE Press to temporarily cut off the sound MENU Press to display the Main Menu on the screen or return to the screen from a sub menu screen CURSOR Press to move the highlight bar for selecting options on the menus And this button is used to change services up down and increase or decrease the audio volume Press to display service list This button is used to select the item on the menus 9 P P Programme up down buttons Press to tune to the next or pre
41. s Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1 2 motor GB8 STB Connections IR 5410Z There are several ways of connecting the STB to your existing Audio TV system We recommend using one of the following set up for best results 1 4 GB9 TV only Connect one end of a 21 pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN connector on your TV Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels Connect the coaxial cable from the LNB to the LNB IN socket on the STB TV with VCR 1 Connect one end of a 21 pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV Connect one end of a 21 pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN connector on your VCR Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN connector on your TV Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels Connect the coaxial cable from the LNB to the LNB IN socket on the STB With Hi Fi System 1 Connect an RCA
42. services on the All Radio services list Organise Favourite A D The Organise Favourite A D lets the user Delete Move Lock Skip or Rename Radio Services from the Favourite Radio Services and group into a new Favourite Radio Services The Radio Services are grouped into a Favourite in the same way as the TV Services refer to page GB26 Organise Service Genre The Organise Service Genre lets the user Delete Lock Skip or Rename Radio Services and group into Radio Service Genres Radio Genres include Pop Rock Country Classic Jazz Folk News Show Sports Education User A D etc The Radio Services are grouped into a Genre in the same way as the TV Services refer to page GB27 Organise Networks You can edit services using the network unit The provider names are displayed on the left side of screen and the TV Radio Services included in the highlighted Network are displayed on the right side of screen Only the Delete Move Rename Function can be used in this mode When TV Radio Services are too many to be displayed use the gt button to move the cursor to the right window and use the A v 52 2 buttons to move the cursor to the next list When the number of services is under 10 the scroll bar is not displayed In Radio Service icon 27 is marked in front of service number GB28 Guide of Main Menu 4 3 Service Searching Enter the PIN code to access the Service Searching menu as you access th
43. the OK button to confirm 4 Press the EXIT button to cancel the deletion Move 1 Press the GREEN button to move the service to where you want to locate Then the icon will be displayed in front of the service number 2 Use the 7 4 buttons to select a new location 3 Press the OK button to fix the location 4 Press the EXIT button to return to the original location Lock 1 Press the YELLOW button to lock services Then the symbol will be displayed at the right side of the Service name 2 Enter the PIN code to view the locked services Skip 1 Press the BLUE button to skip services Then the symbol will be displayed at the right side of the Service name 2 Use NUMERIC buttons 0 9 service list or EPG button to view the skipped services when selecting channels Note You can t view the skipped services by using G2 gt G2 buttons Rename 1 Press the WHITE button to change the service name Then the keyboard image will be displayed on the screen 2 Key in the new service name You can use the four direction keys to move or select the services A to move the previous service v to move the next service lt to move back by services gt to move forwards by services Note The box between service list and the description of the colour buttons offers the brief information of a service where the cursor is located GB25 ip e Caparis
44. the OSD Transparency Information Box Display Time and so on OSD Transparency Select the OSD Transparent type It affects Information box Soundtrack Subtitle Service list Time and Quick mode of TV Guide Use the lt gt buttons to toggle transparent opaque 20 4096 60 and 80 Info Box Display Time Set the display duration of Information box displayed on the screen after changing services The time ranges from 0 to 20 seconds Menu Background Set the type of background for the menu to be displayed on Changing to Reserved Service When the reserved time has come during the view of services Manual Mode This mode shows the message A reserved event has started on another service Press OK to view the reserved service Press EXIT to ignore reserved servicce will automatically change after 10 seconds And ask the presence of change and then makes a change Auto Mode The current service will be automatically changed to the time reserved service GB24 Guide of Main Menu 4 2 Service Organising This menu gives users access to options that allow them to organise their TV Services Radio Services and Networks The default PIN code is Organise TV Services Organise All Services This mode allows users to Delete Move Lock Skip and Rename TV Services Delete 1 Press the RED CD button to delete unwanted services 2 Highlight the services that you want to delete in grey 3 Press
45. the unit Do not stand the STB on soft furnishings or carpets Do not expose the STB to direct sunlight or do not place it near a heater Do not stack electronic equipments on top of the STB Do not use any unrecommended attachments as these may cause hazard or damage the STB CONNECTION TO THE SATELLITE DISH LNB Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish FAILURE TO DO SO CAN DAMAGE THE LNB CONNECTION TO THE TV EARTHING LOCATION A Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish FAILURE TO DO SO CAN DAMAGE THE TV The LNB cable MUST BE EARTHED The earthing system must comply with SABS 061 Place the STB indoor in order not to expose to lightening rain or sunlight A TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE RISK OF ELECTRIC SHOCK REFER SERVICING TO QUALIFIED SERVICE PERSONNEL DO NOT OPEN This symbol indicates dangerous voltage This symbol indicates inside the product that presents a risk of important instructions electric shock or personal injury accompanying the product Warning Please do not insert metal or alien substance into the slots for the Modules and Smart Cards In doing so can cause damage to the STB and reduce its life span GB2 Copyright amp Glossary Copyright VIACCESS is a trademark
46. to select the Genre service list 2 Use the a v lt gt buttons to select a service 3 Press the BLUE button to toggle Genre and service list Note The scroll bar on left of the screen shows the location of the cursor in the selected Genre The scroll bar on right of the screen shows the location of the service Service Alphabet Order 1 Press the WHITE button on the remote control unit to select the Alphabet service list 2 Use the 7 4 buttons to select a service 3 Press the WHITE button to toggle Alphabet and service list Note The scroll bar on left of the screen shows the location of the cursor in the Alphabet The scroll bar on right side of the screen shows the location of the selected Alphabet service GB17 TM Guere rer Guers 2 TV Guide You can watch a programme being shown and reserve it in the TV Guide mode To enter the TV Guide mode Press the EPG button on the remote control unit or select the TV Guide on the Main Menu To select the TV Radio Guide Press the TV Radio button on the remote control unit and TV Guide will be switched to the Radio Guide TV Guide mode includes four different modes To select each mode use the following buttons RED button Use to display the current and next programme list GREEN button Use to display the programme list for one week YELLOW button Use t
47. vious service Press to move up or down pages on the menus HELP Press to display the help box on the screen EPG Electronic Programme Guide button displays the TV Radio programme guide RCL Recall Press to select the service that was previously viewed Please note The design of Remote Control Unit may be changed without notice in advance GB12 Guide of Functions Information Box I Plate The details of service part and event part are automatically displayed on the I Plate when pressing the i button Ci or changing services I Plate is divided into service part and event part SERVICE PART consists of the following items Plate icon Current time and Dolby Digital symbol Service name Service number icons Subtitle Teletext Scrambling service symbol These are automatically displayed when the broadcasting station provides appropriate information Signal quality bar EVENT PART consists of the following items Event name Event duration time Description text of event State of reserved event Event Part shows the current and next event information gt button Use to move from the current event information to the next event information lt button Use to move from the next event information to the current event information When the HELP button is pressed under I Plate display and there are no detailed event informations in the I Plate the Help window will appear
48. ything that may be obstructing the path of the dish amm mE 1 On the Main menu select Service Searching option and press the ill OK button You should now see the Service Searching menu 2 Select Manual Search option and press the OK button you should now see the Manual Search menu 3 Highlight the Antenna Alternative option and press the OK button You should now be in the Satellite Settings menu 4 Press the Ci D gt button to access the Motor Limit Setting menu 5 Highlight the Limit Setting option and use the lt gt buttons to disable this Warning When this option is disabled your motor will be able to move beyond any limits that have been stored please take care in case there are anything obstructing the path of your dish To set the East Limit a Select Movement and use the lt gt buttons to move your motor East or West until the motor is at the position you wish to use as your East Limit Use the lt gt buttons to stop the motor at the correct position b Highlight the Store East Limit option and press the OK button to store the current position as your East Limit GB38 Motorised system To set the West Limit a Select Movement and use the lt buttons to move your motor East or West until the motor is at the position you wish to use as your West Limit Use the lt gt buttons to stop the motor at the correct position b Highlight the Store West Limit option and press the OK butto

Humax IR-5410Z User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents