Hubbell Euclid PBP Pendant User's Manual
Contents
1. 4 and PG5 inserts have one button maintained and one button momentary Terminal Base Cat TB2 required for each plug in insert PG1 PG2 PG3 PG4 PGS PG6 PG7 and MS2 Terminal Base TB5 required for MS5 insert Terminal Base not required with direct wired unit e Power On Off buttons recommended to comply with provisions of NEMA ICS 3 442 15 HUBBELL e H Hae Pai ks Fa i r t r y ail aT Aj HTRARCE 54321 12345 L 4 li ty E i 1 H4 UP FOR veo __ JUMPER BY CUSTOMER DOWN REV J 5 SPEED REAR VIEW For 4 Speed Do Not s Terminal 6 USED TO A MAXIMUM OF THREE SPEED POINTS USED TO A MAXIMUM OF FIVE SPEED POINTS Hubbell Industrial Controls Inc A subsidiary of Hubbell Incorporated 4301 Cheyenne Dr Archdale NC 27262 Telephone 336 434 2800 FAX 336 434 2803 http www hubbell icd com Sales hubbell icd com2. er Where direct wired push buttons are used Steps 3 4 amp 5 do not apply REAR COVER E2 P N 28330 000 E4 P N 28331 000 E6 P N 28332 000 E8 P N 28333 000 PILOT LIGHTS CATALOG LAMP CATALOG LAMP Br ot ter NUMBER PART NO a NUMBER PART NO Pilot Light 120v 60 Hz AC PL1 57465 015 Pilot Light 120V DC PL3 57465 043 Pilot Light 240v 60 Hz AC PL2 57465 015 Pilot Light 240v DC PL4 57465 007 iP tae CABLE ENTRANCE ENCLOSURE DIMENSIONS CONTACT INTERRUPTING RATINGS MULTI SPEED MOTION 1 2 Buttons 2 3 SRE ke ANE DOUBLE BREAK A C 120v 6A 35 PF 240v 3A 125v 250v MULTI SPEED INSERT DESCRIPTION TYPICAL CAT APPLI PLUG IN NO CATION 6 Buttons 5 1 Ibs SINGLE SPEED 4 5 ow EEE E i D C Pilot light is not available on 1 motion enclosure IND SINGLE SPEED INSERT 1 1A 55A TYPICAL APPLI CATIONS SYMBOL MOMENTARY DIRECT SYMBOL PLUG IN WIRED N O MOMENTARY N O amp N C MAINTAINED N O amp N C MAINTAINED MOMENTARY LIFT DROP MOMENTARY MAINTAINED MOMEMTARY START STOP RESET STOP MOMENTARY STOP START STOP RESET MOMENTARY N O MAINTAINED Crane control trolley bridge amp hoist etc Start Stop functions Interlocking crane control Auxiliary functions Magnet control Used as a toggle switch and for start stop functions Start stop on off functions Stop start off on functions t PG
3. oe INSTRUCTIONS HUBBELL main i a Publication No 132 January 1985 Hubbell Industrial Controls Inc Repl January 1984 EUCLID PBP PENDANT PUSHBUTTON STATIONS ASSEMBLY AND PARTS INFORMATION Step 1 Position hanger bracket Item 1 as required and tighten locking nut 1 3 turn past finger tight SS aS Step 2 Pilot light assembly Item 2 if used push out plug E P N 28338 from rear Insert light assembly Insert pilot light legend plate Install locking ring Step 3 Install button assembly not Pictorially shown Align keying tabs and holes and press push button assembly into terminal boards Tighten hold down screws Not used on MS2 amp MS5 AVOID OVERTIGTENING P N 57464 010 Red Lens Step 4 Install terminal board with button assembly working from top to bottom Use 8 32 x 1 2 P N 47661 098 sems screws Item 4 where single thickness terminal board is fastened Observe Top marking on each board AVOID OVERTIGHTENING Step 5 Use 8 32 x 5 8 P N 47661 100 sems screws Item 5 where two terminal boards overlap AVOID OVERTIGHTENING Step 6 Use 8 32 x 1 2 P N 47243 059 pan head screws Item 6 to install button guards and back cover CAUTION DO NOT OVERTIGHTEN THESE SCREWS Recommended torque is 10 in lbs To 12 in lbs Maximum A slight rubber bulging is allowed P N 28329 000 Cover Guard P N 28280 001 All Black Button Cover P N 28280 002 Red Black Button Cov
Download Pdf Manuals
Related Search