Home

Huawei MC509 User's Manual

1. Overall System PTCRB Certification Huawei modules pass the PTCRB certification before being released to the market Huawei performs 2000 to 3000 test items for each type of modules The major tests are as follows e Protocol conformance test e RF conformance test e UIM conformance test The details about the certification tests are defined in the 3GPP test standards According to the PTCRB certification criteria the test reports of modules can be used for the overall system certification The changed parts however need to be re tested Regarding the product structure the antennas and UIM card interface circuits are modified in the integrated equipment For this reason the antennas and the UIM card interface circuits need to be re tested in the overall system certification e OTAtest Different from the GCF certification the PTCRB certification does not require field testing The antenna performance is verified through OTA tests OTA tests are defined by the CTIA for verifying antenna performance e UIM test UIM card interface circuits are re designed in the integrated equipment which may result in changes in the electrical features of the UIM card interface For this reason the UIM card interface circuits need to be re tested The UIM test aims to verify the overall performance of UIM interface with appropriate test instruments in accordance with the relevant 3GPP protocol requirements Similar to the GCF certification th
2. el Bl 5 EH 8 3 3 Power Interface 3 3 1 Overview The power supply part of the MC509 module contains VBAT PIN for the power supply VCOIN PIN for the standby power supply of the real time clock RTC VCC EXT1 PIN for external power output VCC EXT2 PIN for external power output UIM VCC PIN for UIM card power output Huawei Proprietary and Confidential Ge Copyright Huawei Technologies Co Ltd 22 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Table 3 2 lists the definitions of the pins on the power supply interface Table 3 2 Definitions of the pins on the power supply interface Pin No Signal Name I O Description DC Characteristics V Typical Max 12 13 VBAT Pins for power 3 3 3 8 4 2 voltage input 48 49 50 52 53 54 56 57 58 59 106 108 110 112 114 116 35 VCOIN Pin for standby 3 0 power input of the RTC 3 VCC_EXT1 Pin for external 2 6 power output 31 VCC_EXT2 Pin for external 1 8 power output 34 UIM VCC Power supply for 0 3 1 8 2 85 2 1 3 15 UIM card 121 145 GND Thermal Ground Pad 3 3 2 VBAT Interface When the MC509 module works normally power is supplied through the VBAT pins and the voltage ranges from 3 3V to 4 2V typical value 3 8V The 145 pin LGA provides two VBAT pins and sixteen GND pins for external power input To ensure that the MC509 module works normally all the pins must be u
3. 7 1 About This Chapter This chapter gives a general description of certifications e Environmental Protection Certification and Test e National Compulsory Certification e GCF and PTCRB Table 7 1 Product Certifications Certification CE FCC CCC NCC A TICK Jate amp Telec C EU RoHS JGPSSI SGS RoHS PVC Free GCF PTCRB SUPL 1 0 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd m Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications 7 2 Environmental Protection Certification and Test 7 2 1 RoHS RoSH stands for the restriction of the use of certain hazardous substances in electrical and electronic equipment The following table lists the substances restricted by the RoHS and upper thresholds of their density Restricted Substance Hexavalent chromium Cr6 Polybrominated biphenyls PBB 1000 Polybrominated diphenyl ether 1000 PBDE The RoHS does not conflict with the following regulations Battery directive Cadmium directive 91 338 EEC Directive 2004 12 EC on packaging and packaging waste Declaration of Conformity DOC The product is declared as environment friendly or as compliant with the environmental protection requirements after internal testing Notified body NB certification The product passes the test arranged by a notified body SGS and the notified body issues the relevant certificate SGS RoHS
4. Data only version does not support this function Positive pole of the output of speaker interface SPKR OUT N Only telematics version supports audio function Data only version does not support this function Negative pole of the output of speaker interface wo mss po e mmesewe fos pe fan ER LED MODE Mode indicator SINK current source Driver strength 10 mA 102 NC Not connected please keep this pin open 103 NC Not connected please keep this pin open 104 NC Not connected please keep this pin open 105 GPIO l O General I O pins The 0 3 2 6 2 9 function of these pins has not been defined o h joo b b bo o 107 MAIN ANT RF main antenna interface Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 19 ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the Application Interfaces YO Description DC Characteristics V w oo 109 GPIO function of these pins has not been defined we F 111 GPS ANT RF GPS antenna interface 113 GPIO lO General I O pins The function of these pins has not been defined interface 116 COME EN CNNES 124 jo EG EEN 125 RE ry 126 ew i Ce 127 ww e Je 128 ew Ce i io 129 ew Ce i i Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 20 ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the App
5. MC509 Test Value dBm Min Typical Max 4 6 Antenna Design Requirements 4 6 1 Antenna Design Indicators Antenna Efficiency Antenna efficiency is the ratio of the input power to the radiated or received power of an antenna The radiated power of an antenna is always lower than the input power due to the following antenna losses return loss material loss and coupling loss The efficiency of an antenna relates to its electrical dimensions To be specific the antenna efficiency increases with the electrical dimensions In addition the transmission cable from the antenna port of MC509 to the antenna is also part of the antenna The cable loss increases with the cable length and the frequency It is recommended that the cable loss be as low as possible for example U FL LP 088 made by HRS The following antenna efficiency free space is recommended for MC509 to ensure high radio performance of the module Efficiency of the master antenna gt 50 4dB In addition the efficiency should be tested with the transmission cable 11 or VSWR 11 return loss indicates the degree to which the input impedance of an antenna matches the reference impedance 50 ohm S11 shows the resonance feature and impedance bandwidth of an antenna Voltage standing wave ratio VSWR is another Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SS THX RARIS TENA HUAWEI Hardware Guide RF
6. Sudden momentary power loss If the monitored VBAT drops out of range lt 3 3V nominal the SMPL feature may initiate a power on sequence without software intervention and then VBAT returns in range within a programmable interval of between 0 5 and 2 0 seconds SMPL achieves immediate and automatic recovery from momentary power loss A valid voltage on VCOIN is required to run the SMPL timer If a capacitor is used instead of a coin it must be connected between VCOIN and the ground The capacitor must be charged to operate properly as the SMPL power source The capacitor value depends on the SMPL timer setting Table 3 3 Keep alive capacitor values vs SMPL timer settings SMPL timer setting Capacitor package 0 5 sec 1 But 0805 1 5 sec 4 7uUF 0805 2 0 sec 6 8uF 1206 If the SMPL counter expires without VBAT returning to its valid range the MC509 must undergo the normal power on sequence whenever the VBAT is detected Real time clock If RTC is used a manganese lithium rechargeable battery is recommended for example the SII Micro Parts HB 414 and the Panasonic ML series Two sets of coin cell specifications are compared in Table 3 4 When the MC509 is off RTC and its oscillator source are still active provided by a coin cell battery which is installed This allows continued monitoring of RTC alarms programmed via software Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd zi Issue 01 2011
7. vo PCM interface clock interface clock NC Not connected please keep this pin open Not connected please keep this pin open 11 WAKEUP_ IN GPIO Hosttowake up Module to wake Host to wake up Module Module 0 3 EMI Power supply input 13 VBAT Power supply input La PS HOLD This input high to keep power on low to shut SEH 15 Reserved Not connected please keep open Not connected please keep this pin open Not connected please keep this pin open Not connected E keep this pin open Not connected please keep this pin open ZE N NT FE TE EE EN a Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 1 Issue 01 2011 04 08 ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the Application Interfaces rs Description DC Characteristics V 21 a Not connected please keep this pin open 22 NC Not connected please keep this pin open 23 NC Not connected please keep this pin open 24 NC Not connected please keep this pin open 25 NC Not connected please keep this pin open NC Not connected please keep this pin open Not connected please ua ww this pin open 28 Reserved LN JTAG Test mode select JTAG TMS M VCC EXT2 LP 2 6V POWER output Ip In 8V POWER output 32 vcc EXT1 EMI Ki connected please keep this pin open Power supply for UIM E 8 2 8 3 1 3 1 card oS 25 EC 3 Ge Cell ES 15 EC EC TRST_N M
8. 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Table 3 4 Coin cell characteristics Parameter Specifications Nominal capacity 0 3mAh 3 4mAh Continuous standard 5mA 10mA load An interrupt is generated if the coin cell voltage drops too low and the main battery is not present If this interrupt occurs the RTC might be corrupted A different interrupt is generated if the crystal oscillator stops this signifies that handset timing is no longer accurate Again the RTC is corrupted When the VBAT power supply of the MC509 is normal the coin cell charging is powered from VBAT The MC509 reads the coin cell voltage and monitors the charging During normal operation the VCOIN pin voltage will stay above 2 2V even when the coin cell charger is turned off Figure 3 2 shows the reference RTC circuit Figure 3 2 VCOIN interface circuit VCOIN Module DCE Coin Cell 3 3 4 Output Power Supply Interface Output Power Supply Interface includes VCC_EXT1 PIN VCC EXT2 PIN and UIM VCC PIN Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd ES Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Through the Output Power Supply interface the MC509 module can supply 2 6V and 1 8V power externally with an output current of 20mA typical value for external level conversi
9. GPIO Data Terminal Ready 29 UART CTS GPIO UART Clear to Send 29 81 POWER ON OFF System power on or power off CO N Not connected please keep this pin open Not connected please keep this pin open Co CO Not connected please keep this pin open USB DM Full speed USB D USB DP Full speed USB D JTAG_TDI JTAG test data input 0 3 2 9 NEN END EN e 3 X Dd 5 5 M 87 88 c Z Z z E Z Z IM_CLK UIM Clock 1 8 2 8 2 1 3 1 5 5 Status indicator SINK current source Driver strength 10mA Not connected please keep this pin open Kc JTAG return clock 2 9 Not connected please keep this pin open Not connected please keep this pin open LED STATUS oO N in UIM_DATA OJ UIM Data 0 3 1 8 2 8 2 1 3 1 5 5 0 3 0 3 JTAG_RTCK ce oa ES ES i m Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd is Issue 01 2011 04 08 ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the Application Interfaces roi Description DC Characteristics V Normal a Only telematics version supports audio function Data only version does not support this function Negative pole of the output of Earphone interface 97 EAR OUT P Only telematics version supports audio function Data only version does not support this function Positive pole of the output of Earphone interface SPKR OUT P Only telematics version supports audio function
10. NE 80 8 5 Airline Security fia Moses 80 8 6 Safety of Children WA EE S A 80 8 7 Environment Protection 988 9999 90A AE 80 8 8 WEEE Approval emm As ZE ff Tee 80 8 9 RoHS Approval oe MERE 2 eese 80 8 10 Laws and Regulations Obsenvance enne nennen nnne nennen enne 81 8 11 Care and l ltenance 809 Si ee 81 8 12 Emergency Gab 4I MEAS eese 81 8 13 Speeific Absorptlemi alg S AR 29 ENNEN 81 eW aea Uuu WEE 82 8 14 1 CE Approval European Union 82 8 14 2 FCC StaterRElii 99 EE 82 9 Appendix A Circuit of Typical Interfaces eereee eere teer een ee eene eere rntnnnans 83 10 Appendix B Acronyms and Abbreviations reete eene tne tn tns n statuant 85 Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Introduction Introduction This document describes the hardware application interfaces and air interfaces that are provided when the HUAWEI MC509 CDMA LGA Module hereinafter referred to as the MC509 module is used This document helps you to understand the interface specifications electrical features and related product information of the MC509 module To facilitate its use in different fields relevant development guide documents are also provided with the module which can b
11. Specifications Polarization expression of S11 S11 relates to the antenna efficiency S11 can be measured with a vector analyzer The following S11 values are recommended for the antenna of MC509 S11 of the master antenna lt 6dB The polarization of an antenna is the orientation of the electric field vector that rotates with time in the direction of maximum radiation The linear polarization is recommended for the antenna of MC509 Radiation Pattern The radiation pattern of an antenna reflects the radiation features of the antenna in the remote field region The radiation pattern of an antenna commonly describes the power or field strength of the radiated electromagnetic waves in various directions from the antenna The power or field strength varies with the angular coordinates 0 and ol but is independent of the radial coordinates The radiation pattern of half wave dipole antennas can be used for wireless terminals The radiation pattern of half wave dipole antennas is omnidirectional in the horizontal plane and the incident waves of base stations are often in the horizontal plane For this reason the receiving performance is optimal The following radiation patterns are recommended for the antenna of MC509 Master antenna omnidirectional Gain and Directivity The radiation pattern of an antenna represents the field strength of the radiated electromagnetic waves in all directions but not the power density that the ante
12. Test Tested object homogeneous material a material that cannot be mechanically disjoined into different materials such as metal plastic glass ceramics solder and coating Test method IEC62321 or equivalent test methods The following describes the test methods in detail e XRF scanning The XRF scanning measurement can only analyze the calibration substances within its applicability scope For chromium Cr and bromine Br the XRF scanning result shows only the total chromium and total bromine but not hexavalent chromium PBB or PBDE If chromium or bromine is detected you need to further test hexavalent chromium PBB and PBDE by using other test methods The following table lists the required test results Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd i Ws HUAWEI MC509 CDMA LGA Module HUAWEI 7 2 2 WEEE Hardware Guide Certifications Element Polymeric Material Metallic Material Electronic Component Cd PS 70 30 X lt 13043 LOD X 2504 30 lt Pb P lt 700 30 X lt 1300 30 lt F Hg P 700 30 X lt 1300 30 SF Br P 300 3 X Cr P 700 3 X e Chemical analysis Use the ICP AES ICP MS and AAS to measure cadmium and lead in polymeric materials Use the CV AAS AFS ICP AES and ICP MS to measure mercury in polymeric materials metals and electronic components Test the chromized ferrous or non ferrous
13. for energy recovery Huawei Technical Support Department also declares the number and weight of the products delivered every year on the European Recycling Platform According to the European Recycling Platform and the agreements concluded between Huawei and the recycling companies in EU the recycling companies Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 91 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications specified in the agreements are responsible for recycling the telecommunication products 7 2 3 PVC free PVC free products are free of polyvinyl chloride PVC that is harmful to human beings PVC is used to produce soft plastic products such as artificial leather membrane and cable sheaths and hard plastic products such as plates windows doors pipes and valves PVC free test mainly applies to printed circuit boards PCBs and surface mount technology SMT components A notified body must perform PVC free tests qualitative analysis and mixed tests and then issue relevant test reports 7 3 National Compulsory Certification 7 3 1 Product Certification Product certification is the process of certifying that a certain product complies with the electromagnetic compatibility EMC safety and qualification requirements stipulated in relevant international national or industrial regulations and issuing relevant test report and certific
14. g M S E DTE 34V OUTPUT DL MEM E usum MA wows clues 7 GEI 7 E Gre an t t g DA Huawei Proprietary and Confidential 83 Ws HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Appendix A Circuit of Typical Interfaces AUDIO INTERFACE USB INTERFACE HEADSET E f umm Am PII HANDSET E es D em v i E d em RIT i Be P 18106 Am Pr T pI Bi t 1 ES E 2j 2 Ei f 2 E r 3 4 dt em zm Be A Sri l ay BEEN YBa 2 FPF j z sae si zt 7 Xe HANDSPK P ae SIM_CARD S Dee ua EON A ji RUSS ye e SE C SEL en el SEN 3 o wes ET rela E D 232 INTERFACE aw o 1 Status LED i wi V Sr E qe Wook LED y mese mous Lo AI ys RADIO INTERFACE veon j D 85 t 4 Pe 7 T 2 T 4 T E T E Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd i 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Appendix B Acronyms and Abbreviations 1 Appendix B Acronyms and Abbreviations Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SS Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide A
15. install the UC864 E G WD ANDU module Antennas used for this OEM module must not exceed 3dBi gain for mobile and fixed operating configurations Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Si Issue 01 2011 04 08 Wis THX ZRAUBUOCRUS EA HUAWEI Hardware Guide RF Specifications 4 6 4 Radio Test Environment The antenna efficiency antenna gain radiation pattern total radiated power TRP and TIS can be tested in a microwave testing chamber Huawei has a complete set of OTA test environments SATIMO microwave testing chambers and ETS microwave testing chambers The testing chambers are certified by professional organizations and are applicable to testing at frequencies ranging from 380MHz to 6GHz The test items are described as follows Passive Tests Antenna efficiency Gain Pattern shape Envelope correlation coefficient Active Tests e TRP GSM WCDMA CDMA TD SCDMA arid LTE systems TIS GSM WCDMA CDMA TD SCDMA and LTE systems Figure 4 1 shows the SATIMO microwave testing chamber Figure 4 1 SATIMO microwave testing chamber Probe Array mobile under test Active Measurment up ink robe Array driver IEEE link x sia robe Array controller Ethernet link Data acquisition and processing PC Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd To Issue 01 2011 04 08 T RARIS TENA HUAWEI
16. market e Unnecessary tests The GCF does not require the terminals to pass all the tests specified by the 3GPP OMA or IMTC The tests that are not relevant need not to be performed As the GCF test items need to be updated frequently to meet the requirements of new communication technologies the GCF updates the GCF CC version continuously Usually the number of test items increases every time a new GCF CC version is released and terminals are required to pass an increasingly large number of tests The current GCF CC version is 3 35 The GCF updates the GCF CC version every two or three months The previous version is rendered obsolete 110 days after a new version is released All terminal manufacturers need to pay attention to the 110 day rule because additional test items are required after the previous version becomes obsolete All GCF members can view the latest GCF CC version the currently available version and the validity period published on the GCF website Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd 74 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications 7 4 2 PTCRB Certification The PTCRB requirements are certification standards in North America The PTCRB was created in March 1997 GSM 850 MHz requirements were added to the PTCRB requirements in May 2001 which is an important development milestone in the history of standardization organizations in U S A Simi
17. metals by using the spot test method or boiling water extraction If the spot test fails to provide a definite result you can perform boiling water extraction to further confirm the test result If boiling water extraction shows the presence of hexavalent chromium it is confirmed that the sample is coated with hexavalent chromium Measure hexavalent chromium by using the colorimetric method Use a gas chromatograph GC or a mass spectrometer MS to measure PBB and PBDE in polymeric materials Use a high pressure liquid chromatography HPLC or a UV detector to measure PBB and PBDE in polymeric materials The density of lead mercury hexavalent chromium PBB and PBDE needs to be lower than 1000 ppm The density of cadmium needs to be lower than 100 ppm WEEE stands for the Waste Electrical and Electronic Equipment Directive The WEEE mark is on the nameplate of the product Huawei has concluded recycling agreements with four professional recycling companies in Europe According to the agreements the companies are responsible for recycling all Huawei waste equipment in Europe The WEEE Directive aims to reduce the amount of electrical and electronic equipment being produced and to encourage everyone to reuse recycle and recover it The rate of recovery reaches 75 by an average weight per product The reuse and recycling rate of components materials and substances reaches 65 by an average weight per product the additional 10 is
18. numerals indicating the year of issue of the certificate xxxx following the letters CP is four Arabic numerals indicating the sequence number of the certificate CCC The China National Certification and Accreditation Administration of People s Republic of China CNCA is responsible for managing and organizing the CCC The CCC mark is a compulsory safety mark for the products covered in the List of the First Group of Products Being Required Compulsory Product Certification when the products are sold on the Chinese market No listed product can be imported sold or used in China without a CCC certificate issued by designated certification bodies or without a CCC mark CCC marks are classified into standard and non standard marks Huawei products use non standard CCC marks RoHS REACH JGPSSI and Chinese Environmental Protection RoHS the restriction of the use of certain hazardous substances in electrical and electronic equipment According to RoHS directive all electrical and electronic products sold on the EU market should be free of the following six hazardous substances as of July 1 2006 gt lead Mercury Cadmium Hexavalent chromium PBB PBDE The maximum permitted concentrations of the six substances are specified as follows The maximum permitted concentrations of lead mercury hexavalent chromium PBB and PBDE are 1000 ppm 0 1 by weight of homogeneous material The maximum permitted conc
19. of the equipment in particular frequency bands channel spacing type of modulation and RF power and the identification number of the notified body The CE mark is a mandatory European mark Any product placed on the single market in the European Economic Area should be affixed with a CE mark The CE mark of wireless equipment relates to the used frequency bands and the notified body For this reason the CE mark on the nameplate consists of letters C and E the identification number of the notified body and a symbol C NBnr C NBnr FCC Certification FCC stands for Federal Communications Commission The FCC as an independent agency of the United States government is charged with regulating interstate and international communications by radio television wire satellite and cable Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Si Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications FCC regulations as part of federal laws are divided into several parts Different parts define regulations for different products A product however probably is required to meet the regulations in two or more parts All terminals should be certified by the FCC or TCB and granted with an FCC ID The FCC ID format is as follows XXXYYYYYYYY e XXX is the identification number of the applicant manufacturer Huawei QIS e YYYYYYY is the product nu
20. off and resets the hardware through the input signal control pins The power on power off and reset control parts of the interface of the MC509 module include power on power off interface signal POWER ON OFF and the hardware reset interface signal RESIN N The POWER ON OFF pin is used to implement power on and power off If the POWER ON OFF pin is pulled down for atleast 0 5s the module is powered on if the POWER ON OFF pin is pulled down for at least 2 5s again the module is powered off The RESET pin is used to reset the hardware When the software stops responding the RESET pin can be pulled down for 100ms to reset the hardware A CAUTION As the RESET and POWER_ON_OFF signals are relatively sensitive it is recommended that you install a 10nF capacitor near the RESET and POWER ON OFF pins of the interface for filtering In addition when you design a circuit on the PCB of the interface board it is recommended that the circuit length not exceed 20mm and that the circuit be kept at a distance of 2 54mm 100mil at least from the PCB edge Furthermore you need to wrap the area adjacent to the signal wire with a ground wire Otherwise the module may be reset due to interference Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 2i Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Figure 3 3 shows the connections of th
21. seven channels GPIO pins for customers to applications of controlling signal Customers can use AT command to control the state of logic levels of eight channels GPIO output signal See the HUAWEI MC509 CDMA LGA Module AT Command Interface Specification Pin YO Description DC Characteristics V Name 44 46 51 55 GPIO I O General I O 0 3 2 6 2 9 105 109 113 pins Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 19 Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces 3 10 JTAG Interface LGA MC509 module provides one JTAG interface Joint Test Action Group Set the pins in the following table as the test pins And place the test points in the DTE for debug Pin No Pin Name Description IDC Characteristics V 31 VCC EXT2 2 6V POWER 2 6 output Resnn o neat 5 re n JTAG TMS TAG Test 0 3 2 6 2 9 mode select Ce EE GEES EE JTAG_TCK TAG clock 0 3 2 6 2 9 input 72 JTAG_TDO Z TAG test data 0 3 output 87 JTAG_TDI TAG test data 0 3 2 6 2 9 input 93 JTAG_RTCK TAG return 0 3 2 6 2 9 clock 14 PS_HOLD his input high 1 8 to keep power on low to shut down LL note It is recommended that set the 9 pins related to JTAG interface as test points on the DTE for tracing and debug 3 11 RF Antenna Interface MC509 module provides an RF ANT PAD for connecting an external antenna Through
22. without inspection of telecom carriers All products certified by the JATE need to be affixed with certification mark shown in the following figure Sequence numbers are used on the certification marks 0 3A IC Certification Canada IC stands for Industry Canada As a department of the Government of Canada the IC stipulates the inspection standards for analog and digital terminals performs certifications of electrical and electronic products entering the Canadian market and requires that all electronic products imported to Canada must pass EMC certification The involved products include broadcast and TV equipment IT equipment wireless equipment telecommunications equipment and industrial scientific and medical ISM equipment Similar to the FCC the IC applies restrictions on electromagnetic interference only The complete IC certification or registration number is as follows IC XXXXXX YYYYYYYY e XXXXXX XXXXXX is the company number issued by the IC Huawei 63694 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd ar Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications YYYYYYYY YYYYYYYY is the unique product number UPN consisting of up to eight capital letters in English and or digits Chinese Certifications Network access licensing NAL The Ministry of Information Industry MII former Ministry of Posts and Te
23. 011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Safety Information 8 10 Laws and Regulations Observance Observe laws and regulations when using your wireless device Respect the privacy and legal rights of the others 8 11 Care and Maintenance It is normal that your wireless device gets hot when you use or charge it Before you clean or maintain the wireless device stop all applications and power off the wireless device e Use your wireless device and accessories with care and in clean environment Keep the wireless device from a fire or adit cigarette e Protect your wireless device and accessories from water and vapour and keep them dry Do not drop throw or bend your wireless device Clean your wireless device with a piece of damp and soft antistatic cloth Do not use any chemical agents such as alcohol and benzene chemical detergent or powder to clean it e Donotleave your wireless device and accessories in a place with a considerably low or high temperature e Use only accessories of the wireless device approved by the manufacture Contact the authorized service center for any abnormity of the wireless device or accessories e Donotdismantle the wireless device or accessories Otherwise the wireless device and accessories are not covered by the warranty 8 12 Emergency Call This wireless device functions through receiving and transmitting radio signals Therefore the connection cannot be gua
24. 4h High temperature Temperature 85 2 C IEC60068 storage Test duration 24h Low temperature Temperature 30 2 C IEC60068 working Test duration 24h High temperature Temperature 75 2 C IEC60068 working Test duration 24h Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 22 Issue 01 2011 04 08 THX ARAVA SCH RE HUAWEI Hardware Guide Electrical and Reliability Features Item Test Condition Standard Damp heat cycling High temperature 55 2 C IEC60068 Low temperature 25 2 C Humidity 9596 Repetition times 4 Test duration 12h 12h Temperature shock Low temperature 40 2 C IEC60068 High temperature 85 2 C Temperature change interval lt 30s Test duration 15min Repetition times 100 Salty fog test Temperature 35 C IEC60068 Density of the NaCl solution 5x1 96 Spraying interval 8h Duration of exposing the module to the temperature of 35 C 16h Sine vibration Frequency range 5Hz to 200Hz IEC60068 Acceleration 10m s Frequency scan rate 10ct min Test period 3 axial directions Five circles for each axial direction Shock test Half sine wave shock IEC60068 Peak acceleration 300m s Shock duration 11ms Test period 6 axial directions One shock for each axial direction Clash test Half sine wave IEC60068 Peak acceleration 180m s Pulse duration 6ms Repetition time 6 directions 1000 times for each direction Drop test First case 0 3m in h
25. B PADS recommendation 6 4 Label The label is made from deformation resistant fade resistant and high temperature resistant material and is able to endure the high temperature of 260 C Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd af Issue 01 2011 04 08 T RARIS PE HUAWEI Hardware Guide Mechanical Specifications Figure 6 3 Nameplate iae Pim 28mm A X mm mnl HUAWEI TECHNOLOGIES CO LTD MADE IN CHINA 1 1 1mm 3 0mm 28mm LL note e The picture mentioned above is only for reference e Make the film according to the drawing e The silk screen should be clear without burrs and dimension should be accurate e This nameplate should not be covered by the film e The material and surface finishing and coatings which used have to make satisfied with the EU WEE and RoHS directives e The label must be heated up for 20s 40s and able to endure the high temperature of 260 C And the color of the material of the nameplate can t change 6 5 Packing System HUAWE LGA module uses five layers ESD pallet anti vibration foam and vacuum packing into cartons To get the details about the packing system please refer to HUAWEI LGA Module Technical Guide for Assembly Huawei Proprietary and Confidential 58 EE Copyright Huawei Technologies Co Ltd 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications Certifications
26. Company Dames mentioned are the property of their respective owners Notice Some features of the product and its accessories described herein rely on the software installed capacities and settings of local network and may not be activated or may be limited by local network operators or network service providers thus the descriptions herein may not exactly match the product or its accessories you purchase Huawei Technologies Co Ltd reserves the right to change or modify any information or specifications contained in this manual without prior notice or obligation NO WARRANTY THE CONTENTS OF THIS MANUAL ARE PROVIDED AS IS EXCEPT AS REQUIRED BY APPLICABLE LAWS NO WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE MADE IN RELATION TO THE ACCURACY RELIABILITY OR CONTENTS OF THIS MANUAL TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IN NO CASE SHALL HUAWEI TECHNOLOGIES CO LTD BE LIABLE FOR ANY SPECIAL INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES OR LOST PROFITS BUSINESS REVENUE DATA GOODWILL OR ANTICIPATED SAVINGS Import and Export Regulations Customers shall comply with all applicable export or import laws and regulations and will obtain all necessary governmental permits and licenses in order to export re export or import the product mentioned in this manual including the software and technical data
27. EI MC509 CDMALGA Module Hardware Guide Description of the Application Interfaces LO note For detailed information about power supply design and printed circuit board PCB design see the HUAWEI LGA Module Power Supply Design Guide and the HUAWEI MC509 CDMA LGA Module PCB Interconnection Design Guide The MC509 module supports hardware reset function If the software of the MC509 module stops responding the MC509 module can be reset through the RESIN N signal After the hardware is reset the software starts powering on the module and reports relevant information according to the actual settings For example the AT command automatically reports SYSSTART 3 4 3 Output Signal Control Pin TBD 3 4 4 WAKEUP IN Signal The DTE controls the sleep and wakeup status of the MC509 module through the WAKEUP IN signal If there is no external WAKEUP IN signal the wireless module keeps in the wakeup status by default After receiving the WAKEUP IN signal the wireless module determines whether to enter the sleep mode according to the level status of the WAKEUP IN signal Table 3 5 shows the definition of the WAKE IN signal 3 4 5 WAKEUP OUT Signal The WAKEUP OUT signal is used to wake up the external system Figure 3 6 shows the recommended schematic Issue 01 2011 04 08 Huawei Proprietary and Confidential 30 Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Ap
28. ERL Interface EE 31 25 WIVIOW A eene t edet Rt e Ln eh Ea Sedet tet ics 31 3 5 2 Circuit Recommended for the UART Interface ssssssssssssssssseeeeenenenen nes 32 3 0 USB Inter EB MEN ooo ie eee teen e Inti t nee t th atu reiten 33 Salle rell UC e 35 NA MO MU TREE 35 3 7 2 Circuit Recommended for the UIM Card Interface sessnnenensseeestnrnenesenrnnnnnnsernnnnnnsnneeeenn 35 3 7 3 ESD Protection for the UIM Card Interface 37 3 8 Audio Interface 37 3 8 1 Analogue Audio 2 n rete ete gend pru ceat eee t aai AT 37 38 2 Digital AUGIO ET 39 3 9 General Purpose I O Interface 40 Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWeEl Hardware Guide Content 3 10 JTAG Interface aie etd a tna eite a dent die ha ea en deer bli denn da Cose d deg udis 41 3 11 RF Antenna Interface 41 SPA ean E 42 A RF Specification S aient cd dur snaren DUO Le AD PUMA KE HERO EEG EG 43 4 1 About Mul Ce le ET 43 4 2 Antenna Installation Guidelines cece cece eeceaeaeceeeeeeesecsacaeceeeeeeeseccacaeceeeeesesecsaaeeneess 43 4 3 Operating Freouences nennen nemrtr insi enhn EEEE nr tr senis EEEE EnEn 43 4 4 Conducted RF Measurement EE 44 4 4 1 Test Environment AAA EE 44 4 4 2 Test StandardS A AEEEEEEEEE ere nen nennen nenne nennen nns 44 4 5 Conducted Rx S
29. Hardware Guide Electrical and Reliability Features Electrical and Reliability Features 5 1 About This Chapter This chapter describes the electrical and reliability features of the interfaces in the MC509 module including Extreme Working Conditions Working and Storage Temperatures and Humidity Power Supply Features Reliability Features EMC and ESD Features 5 2 Extreme Working Conditions Pw Table 5 1 lists the extreme working conditions for the MC509 module Using the MC509 module beyond these conditions may result in permanent damage to the module Table 5 1 Extreme working conditions for the MC509 module Symbol Specification Minimum Maximum Unit EN NEN IVBAT o VBAT Extemal power External power voltage _ 05 5 VCOIN Input voltage of standby 1 5 15 power for the RTC Vi Datapivotage pin Data pin voltage Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd is Issue 01 2011 04 08 THX ARAVA SCH TENA HUAWEI Hardware Guide Electrical and Reliability Features 5 3 Working and Storage Temperatures and Humidity Table 5 2 lists the working and storage temperatures and humidity for the MC509 module Table 5 2 Working and storage temperatures and humidity for the MC509 module Normal working TBD TBD C temperatures 1 Extreme working TBD TBD temperatures 2 Ambient temperature for TBD TBD C storage Moisture
30. IC2_P o reset Not connected please keep this pin open Only telematics version supports audio function Data only version does not support this function Positive pole of the input of audio interface 2 E N E PE a NW EZX Huawei Proprietary and Confidential a ee Copyright Huawei Technologies Co Ltd ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the Application Interfaces rs Description DC Characteristics V Normal 39 Cem Only telematics version supports audio function Data only version does not support this function Negative pole of the input of audio interface 2 40 MIC1_P Only telematics version supports audio function Data only version does not support this function Positive pole of the input of audio interface 1 41 MIC1 N Only telematics version supports audio function Data only version does not support this function Negative pole of the input of audio interface 1 zm e NS PP me Fe me Cw pL EMI UO Generall O pin The 0 i function of these pins has not been defined W DISABLE Close wireless 0 3 2 6 2 9 communications GPIO lO General I O pins The 0 3 2 6 2 9 function of these pins has not been defined NC Not connected please keep this pin open f Bo ime 31 m LM ee ee ee GPIO UO General I O pins The 0 i function of these pins has not been defined s co h fos mm e L LL pee depu oe e Huawei Pro
31. LO note 1 When the MC509 module works at this temperature all its RF indexes comply with the 3GPP2 C S057D specifications 2 When the MC509 module works at this temperature certain RF indexes do not comply with the 3GPP2 C S057D specifications 5 4 Electrical Features of Application Interfaces Table 5 3 lists electrical features typical values Table 5 3 Electrical features of application interfaces Vu High level input 0 65 VDD_PX VDD_PX 0 3 V voltage Mu Low level input 0 3 0 35 VDD_PX V voltage lieak Input leakage 0 2 0 2 pA current Vou High level VDD PX 0 45 VDD PX V output voltage VoL Low level output 0 45 V voltage lou High level 1 5 mA output current Huawei Proprietary and Confidential 50 pale UTAH TIAE Copyright Huawei Technologies Co Ltd THX ZRAUBUOCRUS TENA HUAWEI Hardware Guide Electrical and Reliability Features loL Low level output 1 5 mA current LO note VDD_PX is 2 6V or 1 8V about the voltage please refer to Table 3 1 5 5 Power Supply Features 5 5 1 Input Power Supply Table 5 4 lists the requirements for input power of the MC509 module Table 5 4 Requirements for input power of the MC509 module Parameter Minimum Typical Maximum Ripple Unit Value Value Value VBAT 3 0 3 8 4 2 lt 50mVpp V OHz to 2 5GHz vco 15 3 25 30mVpp Figure 5 1 lists the Power Supply During Burst Emission Figure 5 1 Power Supply During Bu
32. State Economic and Trade Commission SETC the General Administration of Customs GAC and the Ministry of Foreign Trade and Economic Cooperation MFTEC jointly issued the Provisions on the Management of Import of Radio Transmission Equipment In April 1999 the Ministry of Industry and Information Technology of the People s Republic of China MIIT issued the Notice of Strengthening Management of Radio Transmission Equipment As stipulated in the provisions and notice manufacturers of all radio transmission equipment sold in China should possess the China Radio Transmission Equipment Approval Certificate issued by the SRRC and the relevant CMIIT ID should be affixed to the equipment nameplates Telecommunication equipment manufacturers should submit the China Radio Transmission Equipment Approval Certificate when applying for a network access license to the MIIT In other words completion of equipment type approval is one of the prerequisites for network access application The relevant CMIIT ID should be marked on the nameplate of Huawei radio terminals according to article 4 in the Provisions on Management of Manufacture of Radio Transmission Equipment The following shows an example of the CMIIT ID Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd ee Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications XXXXCPXxxx XXXX before the letters CP is four Arabic
33. VE Sn ab TE aO a T A E E PR 59 TA About THIS Chapte EE 59 7 2 Environmental Protection Certification and Test 60 7 2 TEE 60 52 2 WEBB E 61 V2 3 PV CACC 62 Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd ig HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Content 7 3 National Compulsory Certification sssini nananana aN NAANA RNAAR TANANA AA 62 7 3 1 Product Certification sssssssssssssssssessesee eene enne ennt enn n enter tn ene nnne 62 7 3 2 Importance of Product Certification sss eene 62 7 3 3 Product Certification Test Items enne nnns 62 7 3 4 Product Certification Classifications sss nennen 63 3 5 Certification MOdes ctae ca er eee ENTER OPE LIE ER reget MSN E EUER OPERAI ERR ER dE 63 7 3 6 Certification Types eei tertie ee Ea tee cid dee aab ec Lern nd en ied 64 7 3 7 Guide to Product Certification sssssssssssssssseeeeeeenenen nennen nnns 72 TEGO and R PT CRB teri opera devia tite isi tens 73 7 4 1 GCF Certification tite etate a Rete 73 7 4 2 PTCRB Certification NEEN RENE 75 7 4 3 Overall System Certification EEN ener denne nennen 75 8 Safety Information E EIN lc ees 79 8 1 Interference aaaeeeaa 79 8 2 Medical Device An BRE aeos 79 8 3 Area with Inflammables and Exvplosives Ave 79 8 4 Traffic Security uesees
34. Wz HUAWEI HUAWEI MC509 CDMA LGA Module Hardware Guide Issue 01 Date 2011 04 08 Huawei Technologies Co Ltd provides customers with comprehensive technical support and service For any assistance please contact our local office or company headquarters Huawei Technologies Co Ltd Huawei Industrial Base Bantian Longgang Shenzhen 518129 People s Republic of China Tel 86 755 28780808 Global Hotline 86 755 28560808 Website www huawei com E mail mobile huawei com Please refer color and shape to product Huawei reserves the right to make changes or improvements to any of the products without prior notice Copyright Huawei Technologies Co Ltd 2011 All rights reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co Ltd The product described in this manual may include copyrighted software of Huawei Technologies Co Ltd and possible licensors Customers shall not in any manner reproduce distribute modify decompile disassemble decrypt extract reverse engineer lease assign or sublicense the said software unless such restrictions are prohibited by applicable laws or such actions are approved by respective copyright holders under licenses Trademarks and Permissions Ce w nuawei Huawe and DF are trademarks or registered trademarks of Huawei Technologies Co Ltd Other trademarks product service and
35. aced as close as possible to the UIM card socket and the GND pin of the ESD protection component is well connected to the power GND pin that supplies power to the MC509 module Figure 3 11 ESD protection circuit on the UIM card TVS d UIM Der GND i UIM DATA UIN Fus z UIM_CLK 2 i GND 3 8 Audio Interface 3 8 1 Analogue Audio The MC509 provides two audio I O channels Data only doesn t support the voice function Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd M Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces The two audio I O channels are completely different and thus have good performance of resisting RF interferences The routes on the printed circuit board PCB should be placed in parallel with each other and should be short The filter circuit on the two sides should be symmetric The differential signals should be close to each other The audio output signals in differential pairs and the audio input signals in differential pairs should be separated effectively through ground In addition the audio signals should be located away from the circuits of the power supply RF and antenna The first audio channel can be used for the handset without requiring any audio amplifier The output power for the differential ear output is typically 350mW for a full scale 3dBm sine wave into a 32 ohm speaker The second audi
36. ate 7 3 2 Importance of Product Certification The possible violations of EMC rules are as follows Use certification mark without authorization Supply products without certification mark e Supply incompatible products or apply certification mark to incompatible products e Make incorrect declarations or no compatibility record is created or kept Possible penalties for violation of EMC rules are as follows Sale forbidden Inventory seizure Compulsory callback Fine Being accused or put into prison 7 3 3 Product Certification Test Items A product certification test consists of any or any combination of the following items e EMC Testing electromagnetic interference EMI and electromagnetic sensitivity e Safety Huawei Proprietary and Confidential 62 EE Copyright Huawei Technologies Co Ltd 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications Testing the product according to relevant safety regulations and ensuring that the product does no harm to users RF Measuring whether the radio transmitter meets relevant requirements Specific absorption rate SAR Measuring the RF energy absorbed by the body when an electronic product is used 7 3 4 Product Certification Classifications Product certification is classified into compulsory certification and non compulsory certification Compulsory certification Many countries and regions define compulsory certification marks to facilitate ma
37. ct electronic systems of motor vehicles For more information consult the vehicle manufacturer e In a motor vehicle do not place the wireless device over the air bag or in the air bag deployment area Otherwise the wireless device may hurt you owing to the strong force when the air bag inflates 8 5 Airline Security Observe the rules and regulations of airline companies When boarding or approaching a plane power off your wireless device Otherwise the radio signal of the wireless device may interfere with the plane control signals 8 6 Safety of Children Do not allow children to use the wireless device without guidance Small and sharp components of the wireless device may cause danger to children or cause suffocation if children swallow the components 8 7 Environment Protection Observe the local regulations regarding the disposal of your packaging materials used wireless device and accessories and promote their recycling 8 8 WEEE Approval The wireless device is in compliance with the essential requirements and other relevant provisions of the Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE Directive 8 9 RoHS Approval The wireless device is in compliance with the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive 2002 95 EC RoHS Directive Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SR Issue 01 2
38. ducts in compliant with relevant regulations Ensure that the mark is legible in a single color Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd do Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications An example of the DGT mark Ccxxxxvvyyyzzw A Tick Certification The A Tick is a compliance mark produced by the Australian Communications and Media Authority ACMA for telecommunications equipment The A Tick indicates that a product is compliant with the mandatory technical and safety standards specified by ACMA and can legally be connected to a telecommunications network in Australia All A Tick certification test items should be performed in local labs in Australia The test items are as follows Safety test EMC test SAR test RF test Some test requirements of the A Tick certification are the same as those of the CE certification For this reason CE certification is accepted in Australia to avoid repeated tests The following frequency bands are allocated for mobile communication in Australia at present e 825 845 MHz and 870 890 MHz The CDMA digital technical standards of North America are used e lt 890 915 MHz and 935 960 MHz The GSM digital technical standards of Europe are used e 1710 1785 MHz and 1805 1880 MHz The GSM digital technical standards of Europe are used e 1885 1980 MHz and 2110 2170 MHz The 3G mobil
39. e a remote call 74 UART RTS Data sending request The DTE notifies the 0 3 2 6 2 9 on the wireless DCE of sending module requests 79 UART DTR Data terminal ready The DTE is ready 0 3 2 6 2 9 on the wireless module UART CTS Clearing to send on The DCE switches to 0 3 2 6 2 9 the wireless module the receiving mode 75 UART DCD Data carrier Data links are 0 3 2 6 2 9 detection on the connected wireless module 73 UART DSR Data ready on the The DCE is ready 0 3 2 6 2 9 wireless module 3 5 2 Circuit Recommended for the UART Interface Figure 3 7 shows the connection of the UART interface in the MC509 module DCE with the host DTE Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SS Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Figure 3 7 Connection of the UART interface in the MC509 module DCE with the host DTE Module DCE Application DTE The RS 232 Transceivers can be used to connect the MC509 module to the RS 232 C interface In this connection the complementary metal oxide semiconductor COMS level and the Electronic Industries Association EIA level are converted mutually LL note For detailed application of the MC509 UART interface see the HUAWEI LGA Module UART Design Guide It is recommended that set the pins related to UART interface as test points on the DTE for debu
40. e able to provide high quality and high efficiency test services and are widely recognized by operators Discuss test details with the test organization Provide the test organization with the test report of Huawei modules and the modifications of the integrated equipment The test organization then can determine the detailed test items and determine the test schedule accordingly With the detailed test items and schedule terminal manufacturers can determine accurate plans of product development and marketing Submit an overall system certification application on the PTCRB website and designate a test organization Submit a test application on the PTCRB website indicating the basic information of the terminal to be certified The PTCRB then transfers the application to the designated test organization Remember to pay the CTIA after you submit a test application Unpaid applications are rejected even though all the required tests are performed Perform overall system certification The integrated equipment can pass the over all certification test easily if Huawei s design suggestions are complied with Obtain the test report and submit relevant materials The PTCRB test report is provided by the test organization The terminal manufacturer however is required to provide the user manual and other necessary documents of the terminal to be certified on the PTCRB website before the PTCRB test application can be approved In addition t
41. e 1999 95 EC issued in 2001 authorized test organizations or manufacturers should perform final conformance tests of GSM terminals in compliance with the GCF certification criteria GCF CC Manufacturers then should prepare a DOC and take all responsibilities for quality of the equipment The GCF officially launched the 3G WCDMA certification program in February 2005 The GCF plays an important role in protocol and application conformance testing The GCF provides harmonized standards for conformance tests and defines a test Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 1a Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications system approved by all members to ensure that the terminals meet network deployment requirements All GCF members approve the terminals if the terminals are certified by the GCF The GCF certifies both test cases and test systems The GCF certification originates in Europe and now is accepted by mainstream operators in both Europe and Asia The GCF certification is a DOC of equipment manufacturers Equipment manufacturers only need to perform the test items defined by the GCF and then submit a DOC on the GCF website All GCF members can view the desired DOC on the GCF website The test system defined by the GCF requires thorough conformance tests of terminals The test system consists of indoor and outdoor tests e Outdoor tests mean fi
42. e POWER ON OFF and RESIN N pins Figure 3 3 Connections of the POWER ON OFF and RESIN N pins RESIN H Micro Control DTE Power On Time Sequence After VBAT has been applied and is stable the module will generate an on board power on reset signal and on the release of the reset the module will boot up USB DP will be pulled high when boot up completes simultaneously the module starts to communicate with host via USB or UART Figure 3 4 shows power on timing sequence During power on timing please make sure the VBAT is stable Figure 3 4 Power on timing sequence Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd E HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Table 3 6 Power on timing Parameter Comments Time Nominal Units values POWER_ON_OFF tum on time 0 5 lt Tpon lt 1 Tpp POWER ON OFF Valid to USB 4 Sec D high If the DTE needs to detect the PID VID of module during the BIOS phase the detection time should exceed the Tpps time Figure 3 5 Power off timing High VBAT POWER ON OFF oy Table 3 7 Power off timing Tem POWER ON GEF tum off ime ON OFF turn off time 2 5 lt 25 lt Teo lt s4 lt 4 a ON_OFF Valid to USB Pu M 6 D high Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SS Issue 01 2011 04 08 Wz HUAWEI RESIN_N HUAW
43. e PTCRB certification requires a small number of test items for integrated equipment In addition the required test items are easy to perform with appropriate design suggestions Huawei also provides customers with a PTCRB test report of the module The test is a basis for the PTCRB certification of the equipment integrated with the module Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd 77 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications Terminal manufacturers who apply for the PTCRB certification of the terminals to be integrated with Huawei modules must accomplish the following tasks T Register as a guest of the PTCRB Different from the GCF the PTCRB comprises of only operators Terminal manufacturers can join the PTCRB only as guests The terminal manufacturers who apply for the PTCRB certification have to register as PTCRB guests as they must submit the application on the PTCRB website Choose a test organization The PTCRB requires only qualified test organization to perform PTCRB tests In this case it is necessary for manufacturers to choose a well recognized test organization that provides high quality and high efficiency services The global test organizations 7layers SGS and CETCOM are recommended The recommended test organizations have built various labs all around the world and work closely with the GCF and the PTCRB Therefore the test organizations ar
44. e Sensitivity The conducted receive sensitivity is a key parameter that indicates the receiver performance of MC509 The conducted receive sensitivity refers to the weakest signal that the module at the antenna port can receive The BER must meet the 3GPP protocol requirements in the case of the minimum signal The 3GPP Protocol Claim column in Table 4 1 lists the required minimum values and the Test Value column lists the tested values of MC509 Table 4 1 MC509 conducted Rx sensitivity Unit dBm Item 3GPP2 MC509 Test Value dBm Protocol 7 i Claim dBm Typical Max CDMA800 1x FER lt 0 5 EVDO FER lt 0 5 lt 105 5 E T EIS ae Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd a Issue 01 2011 04 08 THX ARAVA SCH PE HUAWEI Hardware Guide RF Specifications LL note The test values are the average of some test samples 4 5 2 Conducted Transmit Power The conducted transmit power is another indicator that measures the performance of MC509 The conducted transmit power refers to the maximum power that the module tested at the antenna port can transmit According to the 3GPP2 protocol the required transmit power varies with the power class Table 4 2 lists the required ranges of the conducted transmit power of MC509 The tested values listed in the Test Value column mustrange from the minimum power to the maximum power Table 4 2 MC509 conducted Tx power Unit dBm
45. e communication technologies are to be used The A tick mark is as follows TELEC and JATE Certification Japan e Telecom Engineer Center TELEC TELEC is a compulsory certification for radio products in Japan The TELEC certification complies with Japanese Radio Law The specific test regulations are stipulated in MIC Notice No 88 and are updated and maintained by the MIC All N14036 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd d Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications wireless products require type approval mainly for the RF part by Japan Telecom before entering Japanese market e JATE JATE certification is mandatory for telecommunications equipment in Japan according to the Telecommunications Business Law As specified in article 68 in the Telecommunications Business Law enforced in 1985 the Ministry of Public Management Home Affairs Posts and Telecommunications MPHPT has the right to designate qualified agencies for technical certification The MPHPT designates the Japan Approvals Institute for Telecommunications Equipment JATE as the sole authorized agency for technical conditions certification that is JATE certification The JATE provides technical conditions regulatory compliance certifications for telecommunications terminals The certified equipment can legally be connected to public telecommunications networks
46. e obtained from the Huawei website Product name RF Band Bandwidth MC509 CDMA EVDO 1900 800 MHz e lt CDMA EVDO 1900 800 MHz Data only or Telematics MC509 model has two editions Data only or Telematics Data only does not support the voice function Analog voice input function Analog voice output function PCM voice function Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Overall Description 2 Overall Description 2 1 About This Chapter This chapter gives a general description of the MC509 module and provides e Function Overview e Circuit Block Diagram e Application Block Diagram 2 2 Function Overview Table 2 1 Feature Physical Dimensions L x W x H 30mmx30mmx2 6mm Features Weight about 5 5g Working Bands CDMA2000 1x CDMA2000 EV DO Rev 0 CDMA2000 EV DO Rev A Supports BCO 800MHz band BC1 1900MHz band Data only or Telematics Working Normal working temperature 20 C 70 C Temperature Extreme working temperatures 30 C 20 C and 70 C 75 C Ambient 40 C 85 C Temperature for Storage Power Voltage 3 3V 4 2V 3 8V is recommended AT Commands See the HUAWEI MC509 CDMA LGA Module AT Command Interface Specification Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA M
47. ectronic enterprises in January 2001 Since its establishment the JGPSSI has been researching on standardization of green procurement of electrical and electronic products The JGPSSI issued and promoted guidelines for management of chemical substances in products in July 2003 The JGPSSI divides the management of chemicals into the following three processes Acquisition of content information for purchased materials IN information Obtain content information IN information for each substance preparation and each article and confirm the reliability of the content information Manufacture of products using those materials in a manufacturing process Increase the reliability in the daily quality management activities such as preventing the content of incorrect components and preventing contamination by substances preparations or articles that contain prohibited substances Provision of content information for the products sold OUT information Improve reliability by providing content information OUT information for each substance preparation or article e China Environmental protection Administrative Measures on the Control of Pollution Caused by Electronic Information Products that is similar to EU s RoHS Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd 71 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications When designing and manufacturing electronic informat
48. eight Drop the IEC60068 MC509 module on the marble terrace with one surface facing downwards twice Six surfaces should be tested Second case 0 8m in height Drop the MC509 module on the marble terrace with one surface facing downwards twice Six surfaces should be tested Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 53 HR RANSOMES EK HUAWEI Hardware Guide Electrical and Reliability Features 5 7 EMC and ESD Features EMC tests have to be performed on the application as soon as possible to detect any potential problems When designing special attention should be paid to the following e Possible harmful emissions radiated by the application to the RF receiver in the receiver band e ESD protection is mandatory on all signals which are externally accessible Typically ESD protection is mandatory for the following UIM if accessible from outside Serial link USB Audio Length of the UIM interface lines preferably 10cm EMC protection on audio input output filters against 900MHz emissions Biasing of the microphone inputs Ground plane HUAWEI Wireless recommends a common ground plane for analog digital RF grounds e A metallic case or plastic casing with conductive paint is recommended except for the area around the antenna LO note The HUAWEI MC509 Module does not include any protection against over voltage Huawei Prop
49. eld testing of terminals in actual networks Outdoor tests are often performed in the networks of large European operators e Indoor tests include protocol conformance testing and application conformance testing Protocol conformance testing aims to test terminals conformance with 3GPP communication protocols including GSM and WCDMA protocols Application conformance testing aims to test terminals conformance with widely used applications such as browsers SUPL MMS and VT The OMA and the IMTC specify operation and interaction specifications of such upper layer applications Application conformance testing is based on the test standards defined by the OMA and the IMTC Terminals are not required to pass all the GCF tests GCF tests are classified into the following types e Mandatory tests Mandatory tests mean the tests that the terminals supporting the GSM or WCDMA system must pass Mandatory tests cover the capabilities that a terminal must have when it supports communications in the relevant system GSM or WCDMA e Optional tests Optional tests refer to the tests that the terminals supporting a feature specified in the 3GPP protocol or the OMA or IMTC protocols must pass IW a manufacturer is unwilling to perform such tests for its terminals the manufacturer should declare that the terminals do not support the related features and not claim that the terminals support the related features when releasing the terminals to the
50. ensitivity and Tx Power essteeneeeesee E nnnm en enne nns 44 4 5 1 Conducted Receive Sensitivity t I AEn 44 4 5 2 Conducted Transmit Power essere ennt Rn enrnrn nent n nnne ens 45 4 6 Antenna Design Requirements dI EN eiaeia 45 4 6 1 Antenna Design Indicators BBE 48 amp EE iaaa 45 4 6 2 Interference EE ENEE 47 4 6 3 CDMA Antenna Requirement A EEEEEEEEEEEE nnne n nennen 47 4 6 4 Radio Test Environment Zeen EEN 48 5 Electrical and Reliability Features WW igi A 49 5 1 About This Chapter 0 ff Ness 49 5 2 Extreme Working Conditions Net serene hene nennen enne nennen ener enn 49 5 3 Working and Storage Temperatures and Humidity sssesse 50 5 4 Electrical Features of Application Interfaces enne 50 5 5 Power Supply Features 4 ce eecccccccceceeeeeeceaeee De eececceaeceeeeeeesecacaeceeeeeeesecqacaeeeeeeesesecsaaeeeeeeeseteenaees 51 5 5 1 Input PowegsuppL PEE 9 88 51 py PO NOE 0 290 e nnnm 52 5 6 Reliability Features 52 ES EMC and SSD TE EE 54 MNT E ET CMM A 55 6 1 ANAI his Chapter Bl RR EG REOR ERR TES YR ERE XE AERIS e FRE cunsnadedavesadcennenads 55 6 2 DimeNEibns and inteffiSes ne 55 6 3 PCB ch Die eii ir e eer pt et eh det eite td p tiet tutae 56 EE Le CT MEN Am M 57 6 5 PACKING System ET 58
51. entration of cadmium is limited to 100 ppm 0 01 Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd m Wis HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications The EU does not specify any RoHS mark Huawei however designs the preceding RoHS mark to distinguish between environment friendly and environment unfriendly products For Huawei RoHS marks any color is acceptable e REACH Regulation EC No 1907 2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration Evaluation Authorization and Restriction of Chemicals REACH The REACH entered into force on June 1 2007 and was implemented as of June 1 2008 The REACH Regulation is a mandatory preventative regulation on all chemicals sold on the EU market The REACH Regulation creates a large complex chemical management system that transfers the chemicals safety responsibility from the government to the industry Manufacturers importers and downstream users are held responsible for the safety of the chemicals used in their products The REACH Regulation specifies that a substance is regarded as hazardous until proven safe The earlier EU chemical regulations however specifies that a substance is regarded as safe until proven hazardous e JGPSSI Japan Green Procurement Survey Standardization Initiative The JGPSSI was established by some Japanese electrical and el
52. g 3 6 USB Interface The MC509 is compliant with USB 2 0 full speed protocol The USB interface is powered directly from the 3 3 V supply The USB input output lines are compatible with the USB 2 0 3 3 V signal specifications Oshows the circuit of the USB interface Table 3 9 USB interface signals o USB DP IO USB data signal D USB_DM uo USB data signal D Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd 28 Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces LL note The USB interface is powered directly from the 3 3 V supply The USB input output lines are compatible with the USB 2 0 3 3 V signal specifications Table 3 10 DC Electrical Characteristics of USB J2 LL note e Since the USB interface of MC509 module supports USB 2 0 full speed the resistance RV102 and RV103 in the Omust be Voltage Sensitive Resistor with small capacitance ALVC18S02003 manufactured by AMOTECH or B72590T7900V60 manufactured by EPCOS is recommended In addition The layout design of this circuit on the DTE board should comply with the USB 2 0 full speed protocol with differential lining and impedance control to 90 ohm e tis recommended that set USB D and USB D pins as test points and then place these test points on the DTE for debug Huawei Proprietary and Confidential 34 EE Copyright Huawei Technologie
53. ght Huawei Technologies Co Ltd am HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces A CAUTION To meet the requirements of ETSI TS 102 230protocols and electromagnetic compatibility EMC authentication the UIM card socket should be placed near the LGA interface it is recommended that the PCB circuit connecting the LGA interface and the UIM card socket not exceed 100mm because a long circuit may lead to wave distortion thus affecting signal quality e tis recommended that the user should wrap the area adjacent to the UIM_CLK and UIM_DATA signal wires with a ground wire The GND pin of the UIM card socket and the GND pin of the UIM card must be well connected to the power GND pin supplying power to the MC509 module e AO 1yF capacitor is placed between the UIM VCC and GND pins in a parallel manner Three 10pF or 33pF capacitors are placed between the UIM DATA and GND pins the UIM RST and GND pins and the UIM CLK and GND pins in parallel to filter interference from RF signals e tis not recommended that pull the UIM DATA pin up during design as a 15000 ohm resistor is used to connect the UIM DATA pin to the UIM VCC 3 7 3 ESD Protection for the UIM Card Interface It is recommended to take electrostatic discharge ESD protection measures near the UIM card socket Figure 3 11 shows ESD protection circuit of the UIM card in which the transient voltage suppressor TVS diode is pl
54. hat affect the normal operation of the module For example the module sensitivity can be decreased due to interference signals Therefore during the design you need to consider how to reduce the effects of interference sources on the module You can take the following measures Use an LCD with optimized performance shield the LCD interference signals shield the signal cable of the board or design filter circuits Huawei is able to make technical suggestions on radio performance improvement of the module 4 6 3 CDMA Antenna Requirements The antenna for MC509 must fulfill the following requirements CDMA Antenna Requirements Frequency range Depending on frequency band s provided by the network operator the customer must use the most suitable antenna for that those band s Bandwidth 80MHz in CDMA800 140MHz in CDMA1900 Gain Gain lt 3dBi Furthermore if the device is developed for the US and or Canada market it must comply with the FCC and or IC requirements This device is to be used only for mobile and fixed application The antenna s used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter End users must be provided with transmitter operation conditions for satisfying RF exposure compliance OEM integrators must ensure that the end user has no manual instructions to remove or
55. he PTCRB submits all the materials to the CTIA for review on completion of all the PTCRB tests The terminal is PTCRB certified on completion of the CTIA review GCF and PTCRB Certification To launch a terminal in the global market both the GCF certification and the PTCRB certification are required In this case the manufacturer does not need to conduct two end to end tests As the UIM test is the same for both the GCF certification and the PTCRB certification the test organization needs to perform the UIM test only once This practice is recognized by both the GCF and the PTCRB The cost including time and expense of overall system certification is thus reduced Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd m 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Safety Information Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device Applicable safety information must be observed 8 1 Interference Power off your wireless device if using the device is prohibited Do not use the wireless device when it causes danger or interference with electric devices 8 2 Medical Device e Power off your wireless device and follow the rules and regulations set forth by the hospitals and health care facilities e Some wireless devices may affect the performance of the hearing aids For any such problems consult y
56. he test report The PTCRB should also publish the certification on its website for viewing and querying by the PTCRB members The PTCRB certification is similar to the GCF certification in terms of test system The only difference is that no field testing is performed in the case of the PTCRB certification OTA tests are adopted to measure the antenna performance The PTCRB test items and version are also updated continuously Different from the GCF CC version only one PTCRB version is valid at any time Each PTCRB version is valid for three months Manufacturers are not allowed to apply for the previous version of PTCRB certification if a new version is released For a terminal for which the manufacturer has applied for the previous version of PTCRB certification before the new version is released the manufacturer needs not to apply for the new version if the PTCRB certification is completed within nine months 7 4 3 Overall System Certification Both the test system and test items of the GCF certification are similar to those of the PTCRB certification Both certifications test the declared capabilities of terminals based on the 3GPP test standards The integrated equipment needs to pass relevant certification tests even though the modules pass the conformance certification The following describes the overall system certification procedures in detail The overall system can be a notebook a MID a smartphone etc Huawei Proprietary and Co
57. ied to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure The SAR limit adopted by the USA and Ganada is 1 6 watts kilogram W kg averaged over one gram of tissue The highest SAR value reported to the FCC for this device type was compliant with this limit 8 14 2 FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The antenna s used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons Warning Changes or modifications made to this equipment not expressly approved by HUAWEI may void the FCC authorization to operate this equipment Huawei Proprietary and Confidential 82 EE Copyright Huawei Technologies Co Ltd Ws HUAWEI MC509 CDMA LGA Module Hardware Guide Appendix A Circuit of Typical Interfaces HUAWEI Appendix A Circuit of Typical Interfaces Issue 01 2011 04 08 Copyright Huawei Technologies Co Ltd MC509 INTERFACE JTAG TP U202 ER ec Zen LGA e Qi cum 3 AS 8 Qs ety D e MU g e IMG Gc soar Le epou poucieou Qt ew XM BE 8 H S 8 POWER SUPPLY me P ina
58. ion products the manufacturers should use materials technologies and processes that are easily recyclable and environment friendly in accordance with the relevant industrial or national standards All electronic information products sold on Chinese market should be marked with the names and contents of toxic and harmful substances and elements safety period and recyclability The use of six hazardous substances is prohibited or limited in the products listed in the administrative catalogue for the control of pollution caused by electronic information products The catalogue is not determined at present It is estimated that the first catalogue is to be issued at the end of year 2009 Printers telephones and mobile phones might be listed in the catalogue The control of toxic and harmful substances in electronic information products is covered in the CCC management Sixhazardous substances are prohibited including lead mercury cadmium hexavalent chromium PBB and PBDE Other hazardous substances defined by China are also prohibited No exemption clause is defined in the Administrative Measures on the Control of Pollution Caused by Electronic Information Products The Marking for the Control of Pollution Caused by Electronic Information Products SJ T11364 2006 issued on November 6 2006 specifies that the mark should indicate whether the electronic information products contain any toxic or hazardous substances or element
59. lar to the GCF the PTCRB comprises of operators and mainstream mobile phone manufacturers and approved laboratories The PTCRB was created by North American operators Cingular T Mobile and Rogers and is applied to North America Central America and South America The PTCRB certification is similar tothe GCF certification except that the PTCRB certification acts as the license for the UMTS terminals to be connected to American operators networks Only the PTCRB certified terminals are accepted by mainstream operators The PTCRB certification also differs from the GCF certification in the frequency bands because the frequency bands used in America differ from those in Europe The PTCRB focuses on the GSM 850 MHz GSM 1900 MHz WCDMA FDD II and WCDMA FDD V while the GCF focuses on the GSM 900 MHz GSM 1800 MHz and WCDMA FDD Different from the GCF certification the PTCRB certification does not allow DOC The entire certification process should be performed under the PTCRB s supervision and all the certification tests should be performed in the labs authorized by the PTCRB A manufacturer who applies for the PTCRB certification needs to submit a test application to the PTCRB and then the PTCRB will transfer the application to the test organization designated by the manufacturer The test organization should perform the test and then submit the test report to the PTCRB for review The PTCRB certification is completed if the PTCRB approves t
60. lecommunications applies NAL to telecommunications equipment On January 1 1999 with the enforcement of the Administration of the Network Connection of Telecommunications Equipment Procedures issued by the MII all telecommunications equipment that access public or private telecommunications networks in China should obtain network access licenses issued by the MII No telecommunications equipment can be connected to a public telecommunications network or be sold in China without a network access license A network access license includes the following information License number Applicant Manufacturer Equipment name Equipment type Place of manufacture Remarks Date of issue Date of expiry A network access license often is valid for three years The Telecommunications Administration Bureau MII is responsible for inspecting and approving telecommunications equipment and then issuing network access licenses according to the inspection results Local telecommunication administration departments are responsible for supervising and managing network access of telecommunications equipment in the local regions The network access certification is called China Telecommunications Equipment Network Access Approval TENAA or CTA or China Telecommunications Equipment Network Access Licensing NAL NAL marks should meet the following requirements NAL marks are the quality compliance marks affixed to the telecommunicati
61. lication Interfaces Normal MUX Max 2 omo Le e i ono Lee i ono Lee ee s ono Lee as ono Le 249 i Tag Lee L ae ono Ce FN ss ono be dE N o Tag bes M m ono ch 9 m2 Tag e Wf s ono ew RES Aw WII ws ono ww LL note e P indicates power pins indicates pins for digital signal input O indicates pins for digital signal output e The NC Not Connected pins are internally connected to the module Therefore these pins should not be used otherwise they may cause problems Please contact us for more details about this information e When the MC509 module works on master mode PCM CLK and PCM SYNC pins are in the output status Figure 3 1 shows the sequence of pins on the 145 pin signal interface of the MC509 module Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd i Issue 01 2011 04 08 Ws HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Figure 3 1 Bottom view of sequence of LGA interface pins a a eE eai E PELE CLE SS a sd A A CHEIDED HRS es es f2 bk x Be S BHBEGCNBEBS er paas Jeu paas Controipads Dll rr ant paas Bluse B umpacs jusspadcs J ooo paas GPiOpads Donotuse zl REEERSEERSS OR Es 8 8 E 8 8 8 5 8 8 B8 8 57 25 83 23 8 22 3 20 B Co IH ie BI L7
62. lines e lt Install the antenna in a place covered by the signal e TheAntenna must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter e Antenna must not be installed inside metal cases e Antenna must be installed also according Antenna manufacturer instructions 4 3 Operating Frequencies See RRA SIH shows the RF bands supported by MC509 RF bands CDMA 800 BCO 824MHz 849MHz 869MHz 894MHz CDMA 1900 BC1 1850MHz 1910MHz 1930MHz 1990MHz Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd 43 THX ARAVA SCH PE HUAWEI Hardware Guide RF Specifications 4 4 Conducted RF Measurement 4 4 1 Test Environment Test instrument Agilent 8960 Power supply KEITHLEY 2306 RF cable for testing L08 C014 350 of DRAKA COMTEQ or Rosenberger Cable length 29cm Compensation for CDMA 850MHz 0 8dB Compensation for CDMA 2100MHz 1dB CO note e The compensation for different frequency bands relates to the cable and the test environment e The instrument compensation needs to be set according to the actual cable conditions 4 4 2 Test Standards Huawei modules meet all 3GPP2 teststandards relating to 3G Each module passes strict tests at the factory and thus the quality of the modules is guaranteed 4 5 Conducted Rx Sensitivity and Tx Power 4 5 1 Conducted Receiv
63. mber consisting of two to 14 digits An FCCID consists of capital letters in English digits and symbols only No other character is allowed For any Huawei product the product model is used as the product number For example the FCC ID of the EM770W is QISEM770W NCC DGT Certification According to Telecommunications Act and Regulations on Inspection and Certification of Controlled Telecommunications Equipment of Taiwan no communication and electronic equipment can be manufactured or sold in Taiwan unless certified by the NCC former DGT with relevant certification marks The following lists the controlled telecommunications equipment Radio transmitter Radio transceiver Radio receiver Radiated device Other radio sources The DGT s Technical Specifications for Low Power Radio Frequency Devices specifies the frequencies that no low power RF device or its principal wave should not use and control the radiation field strength of low power RF devices Comply with the following rules when making DGT marks e Comply with the Technical Specifications for Low Power Radio Frequency Devices and the Compliance Approval Regulations on Controlled Telecommunications Radio Frequency Devices e Affix or print marks of appropriate size on the equipment bodies because the dimensions are not specified e Affixor print the DGT mark on the minimal package if the equipment body is small to the mark e Attach the DGT mark to relevant pro
64. nfidential Copyright Huawei Technologies Co Ltd i Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications Overall System GCF Certification Huawei modules pass the GCF certification before being released to the market Huawei performs 2000 to 3000 test items for each type of modules The major tests are as follows e Protocol conformance test e RF conformance test e UIM conformance test The details about the certification tests are defined in the 3GPP test standards According to the GCF CC the test reports of modules can be used for the overall system certification The changed parts however need to be re tested Regarding the product structure the antennas and UIM card interface circuits are modified in the integrated equipment For this reason the antennas and the UIM card interface circuits need to be re tested in the overall system certification e Field test The antenna performance relevant field test is required due to changes in the antennas and to test the equipments functions and its interoperability with networks on five networks run by different European operators To be specific the field test tests the basic functions of the UE on actual networks and determines whether the UE passes the testing according to the UE performance e UIM test UIM card interface circuits are re designed in the integrated equipment which may result in changes in the electrical feature
65. nna radiates in the specific direction The directivity of an antenna however measures the power density that the antenna radiates Gain as another important parameter of antennas correlates closely to the directivity The gain of an antenna takes both the directivity and the efficiency of the antenna into account The appropriate antenna gain prolongs the service life of relevant batteries The following antenna gain is recommended for MC509 Gain of the master antenna S 2 5dBi L note e The antenna consists of the antenna body and the relevant RF transmission cable Take the RF transmission cable into account when measuring any of the preceding antenna indicators e Huawei cooperates with various famous antenna suppliers who are able to make suggestions on antenna design for example Amphenol Skycross Pulse etc Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SS TH RARIS TENA HUAWEI Hardware Guide RF Specifications 4 6 2 Interference Besides the antenna performance the interference on the user board also affects the radio performance especially the TIS of the module To guarantee high performance of the module the interference sources on the user board must be properly controlled On the user board there are various interference sources such as the LCD CPU audio circuits and power supply All the interference sources emit interference signals t
66. o channel can be used for the hands free without requiring any audio amplifier The output pins are configured differently with a rated output of 500 mW into an 8Q speaker Considerable current flows between the audio output pins and the speaker and thus wide PCB traces are recommended 20mils MC509 provides 2 2V power source and mA of bias current internally for the microphones of both audio channels Figure 3 12 Circuit diagram of the interface of the first audio channel Module DCE MIC1 P ESD protection k MIC1 N e EAR OUT P C9 EAR OUT N Network Connector 1nF 1nF ji E zs LE Issue 01 2011 04 08 Huawei Proprietary and Confidential 38 Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Figure 3 13 Circuit diagram of the interface of the second audio channel ferrite bead SPKR OUT P ferrite bead ESD protection SPKR OUT N if 1nF 1nF Module DCE ferrite bead MIC2 P 1nF ferrite bead q 1nF E LW d ESD protection 1nF LL note e tis recommended that a TVS be used on the related interface to prevent electrostatic discharge and protect integrated circuit IC components e Data only does not support the voice function 3 8 2 Digital Audio The MC509 provides one digital audio channels Da
67. odule HUAWEI Hardware Guide Overall Description Application Universal Asynchronous Receiver Transmitter UART Interface 145 Supporting 8 wire UART pin LGA interface One standard user interface Module UIM card 3V or 1 8V Audio OPTION only telematics version supports this function For detailed information about the working bands supported see fiu RRAGA e 2xMicphone in e 1xSpeaker out e 1xhandset out e 1xPCM Light emitting Diode LED SMS New message alert text message receiving and text message sending Management of text messages read messages delete messages storage status and message list Support for the Protocol Data Unit PDU mode Data Services CDMA2000 1X UL DL 153 6kbps CDMA2000 1X EVDO rev 0 UL 153 6kbps DL 2 4Mbps CDMA2000 1X EVDO rev A UL 1 8Mbps DL 3 1Mbps Internet TCP IP UDP IP PPP protocol Protocols Applications TBD Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd i Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Overall Description Certification e Restriction of the use of certain Hazardous Substances Information RoHS e Federal Communications Commission FCC China Compulsory Certification CCC e China Telecommunications Equipment Network Access Approval CTA e Waste Electrical and Electronic Equipment Directive WEEE 2 3 Circuit Block Diagram Figure 2 1 shows the circui
68. on or other applications If the MC509 module is in Sleep mode the Output Power Supply interface is in the low power consumption state lt 500pA If the MC509 module is in Power Down mode the Output Power Supply is in the disabled state 3 4 Signal Control Interface 3 4 1 Overview The signal control part of the interface in the MC509 module consists of the following Power on off POWER ON OFF pin Hardware reset RESIN N pin Network status LED LED STATUS LED MODE pin WAKEUP IN Signal WAKEUP IN pin WAKEUP OUT Signal TBD Table 3 5 lists the pins on the signal control interface Table 3 5 Pins on the signal control interface Pin Name I O Description DC eee DC Characteristics V Se SE ON OF Pin for controlling uw and power 100 RESIN N Pin for resetting the hardware LED STATUS 3 Pin for network status ES LED 101 LED MODE Pin for network mode LED 11 WAKEUP_IN H DTE wakeup MC509 L DTE set MC509 to sleep mode WAKEUP_OUT H MC509 wakeup DTE L MC509 set DTE to sleep mode Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 26 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces LL note It is recommended that use resistance of Oohm in the DTE to isolate signals transmitted from above pins in Table 3 5 3 4 2 Input Signal Control Pins The MC509 module implements power on and power
69. ons equipment that obtains network access licenses NAL marks are printed and issued by the MII NAL marks can be purchased for the equipment that obtains network access licenses NAL marks should be affixed firmly to the telecommunications equipment that obtains network access licenses Forging or illegally using NAL marks is forbidden No NAL mark can be affixed to the telecommunications equipment that fails to obtain network access licenses or whose network access licenses expire The following figure shows an example of NAL marks Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Go Wis HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications The following figure shows the anti counterfeiting measures of NAL marks Ameans the fluorescent anti counterfeiting string inside the mark The anti counterfeiting string is visible under UV light and can be exposed with a knife B means the anti counterfeiting shading that supports anti photography and anti forgery C means the invisible CMII fluorescent mark that is visible under UV light D means the characters that use microform printing Emeans the unique computer scrambling code that relates to the license number equipment type and sequence number The scrambling code cannot be copied e Type approval On July 24 1995 the former State Radio Regulatory Committee SRRC the
70. our service provider e Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between the wireless device and a pacemaker to prevent potential interference with the pacemaker If you are using an electronic medical device consult the doctor or device manufacturer to confirm whether the radio wave affects the operation of this device 8 3 Area with Inflammables and Explosives To prevent explosions and fires in areas that are stored with inflammable and explosive devices power off your wireless device and observe the rules Areas stored with inflammables and explosives include but are not limited to the following Gas station Fuel depot such as the bunk below the deck of a ship Container Vehicle for storing or transporting fuels or chemical products Area where the air contains chemical substances and particles such as granule dust or metal powder Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd i Issue 01 2011 04 08 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Safety Information e Area indicated with the Explosives sign Area indicated with the Power off bi direction wireless equipment sign Area where you are generally suggested to stop the engine of a vehicle 8 4 Traffic Security Observe local laws and regulations while using the wireless device To prevent accidents do not use your wireless device while driving e RFsignals may affe
71. plication Interfaces Figure 3 6 Connections of the WAKEUP_IN and WAKEUP_OUT pins VCC_EXT2 WAKEUP_IN WAKEUP OUT 3 5 UART Interface 3 5 1 Overview The MC509 module provides the RS 232 UART 9 wire UART interface for one asynchronous communication channel As the UART interface supports signal control through standard modem handshake AT commands are entered and serial communication is performed through the UART interface The UART has the following features Full duplex 7 bit or 8 bit data 1 bit or 2 bit stop bit Odd parity check even parity check or non check Baud rate clock generated by the system clock Direct memory access DMA transmission Baud rate ranging from 600 bit s to 230400 bit s 115200 bit s by default Self adapted baud rate ranging from 1200 bit s to 115200 bit s Table 3 8 lists the UART interface signals Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd al Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Table 3 8 UART interface signals Pin Pin Name YO Description Feature DC Characteristics V No 76 UART TX Data sending on the The DTE receives 0 3 2 6 2 9 wireless module serial data 78 UART RX Data receive end of The DTE transmits 0 3 2 6 2 9 the module serial data 77 UART RIN Ringing indication on The DTE is notified of 0 3 2 6 2 9 G the wireless modul
72. ppendix B Acronyms and Abbreviations PDU protocol data unit RoHS Restriction of the use of certain Hazardous Substances Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Bp Issue 01 2011 04 08
73. prietary and Confidential Copyright Huawei Technologies Co Ltd E Issue 01 2011 04 08 ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the Application Interfaces rs Description DC Characteristics V 55 a General I O pins The 0 3 2 6 2 9 function of these pins has not been defined s jew bh kde o e be m o fee iia e m o CC LL ee ud Lr LE NC Not connected please keep this pin open 61 NC Not connected please keep this pin open 62 NC Not connected please keep this pin open 63 NC Not connected please keep this pin open 64 NC Not connected please keep this pin open 65 NC Not connected please keep this pin open NC Not connected please keep this pin open 67 NC Not connected please keep this pin open NC Not connected please keep this pin open NC Not connected please keep this pin open 70 NC Not connected please keep this pin open WAKEUP OUT GPIO ps Module to wake up the host Er wave e moesson as n s Gs ues emo o uarroas setneew us 20 5 o ues emo o usrmmeereee o3 n 20 Us uen omo o uart oaa carer oaea 03 Jo 29 bs ue oro o Justeenasg o3 20 fzo Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 17 ia HUAWEI MC509 CDMALGA Module HUAWEI Hardware Guide Description of the Application Interfaces Pin Name YO Description DC Characteristics V 79 UART DTR
74. ranteed in all conditions In an emergency you should not rely solely on the wireless device for essential communications 8 13 Specific Absorption Rate SAR Your wireless device is a radio transmitter and receiver It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons regardless of age and health The guidelines use a unit of measurement known as the Specific Absorption Rate or SAR The SAR limit for wireless devices is 2 0 W kg and the highest SAR value for this device when tested complied with this limit Huawei Proprietary and Confidential 81 Ge Copyright Huawei Technologies Co Ltd Wis HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Safety Information 8 14 Regulatory Information The following approvals and notices apply in specific regions as noted 8 14 1 CE Approval European Union The wireless device is approved to be used in the member states of the EU The wireless device is in compliance with the essential requirements and other relevant provisions of the Radio and Telecommunications Terminal Equipment Directive 1999 5 EC R amp TTE Directive Federal Communications Commission Notice United States Before a wireless device model is available for sale to the public it must be tested and certif
75. rietary and Confidential Copyright Huawei Technologies Co Ltd zn Issue 01 2011 04 08 TH ARAVA SCH PES HUAWEI Hardware Guide Mechanical Specifications 6 Mechanical Specifications 6 1 About This Chapter This chapter describes the following aspects of the MC509 module Dimensions and interfaces PCB Pad Design Label Packing System 6 2 Dimensions and interfaces Thedimension of MC509 is 30mm length x 30mm width x 2 6mm height Figure 6 1 shows the dimensions of MC509 in details Figure 6 1 Dimensions of MC509 30 00 40 20 Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd x Wa THX ARRAY SC Fe EA HUAWEI Hardware Guide Mechanical Specifications 6 3 PCB Pad Design To achieve assembly yields and solder joints of high reliability it is recommended that the PCB pad size be designed as follows the size of the pad in the middle region is the same as the pad size of the product package other pads are 0 05 mm larger than the unilateral pad of the product package For details see Figure 6 2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd ap Issue 01 2011 04 08 TH IRAUBUOCRUS TENA HUAWEI Hardware Guide Mechanical Specifications Figure 6 2 PCB pad design SEE DETAIL A Gr yo Sec SEE DETAIL B E J E 18 0 l SEE DETAIL C SA zc 27 0 LGA module customer PC
76. ription of the Application Interfaces 3 1 About This Chapter This chapter mainly describes the external application interfaces of the MC509 module including LGA Interface Power Interface Signal Control Interface UART Interface USB Interface UIM Card Interface Audio Interface General Purpose UO Interface JTAG Interface RF Antenna Interface NC Pins 3 2 LGA Interface The MC509 module uses a 145 pin LGA as its external interface For details about the module and dimensions of the LGA see 6 2 Dimensions and interfaces If DTE supports Huawei LGA module such as module with system of CDMA TD SCDMA or HSPA you can refer to Huawei LGA Migration Guide to get the details Table 3 1 shows the definitions of pins on the 145 pin signal interface of the MC509 module Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd te Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Table 3 1 Definitions of pins on the LGA interface PIN pes Description DC Characteristics V No P Not connected please keep this pin open NC Not connected please keep this pin open Not connected please keep this pin open Not connected please keep this pin open 5 PCM SYNC GPIO vo PCM interface sync interf ce PCM interface sync DIN Si PCM I F data in PIO SC DOUT 2 Gem fi I F data out 8 PCM CLK GPIO
77. rket supervision of the commodity inspection organizations For example the Certification Europe CE mark Federal Communications Commission FCC mark in U S A and China Compulsory Certificate CCC mark are compulsory certification marks Only the products with required compulsory certification marks can be sold in the relevant countries or regions Non compulsory certification Non compulsory certification is also called voluntary certification Compared with compulsory certification marks the certification marks issued by independent certification bodies are more common in international trade The PCS Type Certification Review Board PTCRB in America and the Global Certification Forum GCF in Europe are two typical examples of non compulsory certification marks Non compulsory certification marks are issued by authorized non governmental certification bodies based on the product liability laws in relevant countries and are recognized by the local governments Compared with governmental bodies non governmental certification bodies are more professional with better test conditions and more positive certification measures In addition non governmental certification bodies are under supervision of their authorizing administrations For these reasons the certification marks issued by non governmental certification bodies are widely recognized in the market and are essential to international trade 7 3 5 Certification Modes DOC By affi
78. rmation of using the product Lists the circuit of typical interface of the product Lists the acronyms and abbreviations mentioned in this document Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Content Content E lrsaserel E BER 8 2 Overall Description ER d 9 2 1 About This Chapter t eene eee candies emo 9 2 2 Function Overview sess alB ee 9 2 3 Circuit Block Diagram de BE E iaaa aa aaa 11 2 4 Application Block Diagram EENEG 12 3 Description of the Application Interfaces 4 eee eerte eene teen tn aenea tns in statuant 13 3 1 About This Chapter eben stemmate ener nnn nnn n nennen nr tr nnne nn nnne EEEE ESEESE nnns 13 3 2 LGA Interface 898099 Iesse 13 3 3 Power Interface 4A ff E 22 3 3 1 Uveniew nn E ff 0 e 22 3 3 2 VBAT Interface M 4209 ff 23 3 3 3 VCOIN Inidi3ee 20 ME EE 24 3 3 4 Output Power Supply Interface ek 25 3 4 Signal Contfellilnterface BE 9898 eese 26 3 4 1 Overview OO aeaaaee aeaaaee eenen annann ee eannan naene enna 26 3 4 2 Input Signal Control Pins ee 27 3 4 3 Output Signal Control Pin TBD eee nnnm nennen nnne 30 3 4 4 WAKEUP V igna EE eter toic eaa tta itis 30 3 4 5 WAKEUP Ofbau MK tnnt 30 35 W
79. rst Emission VBAT VBAT Voltage Signal LS EC Ripple Ripple TX Burst Timing Sequence Table 5 5 Requirements for input current of the MC509 module ene Peak Maximum Normal Maximum lt 1500mA 1000mA Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd al Issue 01 2011 04 08 THX ARAVA SCH TENA HUAWEI Hardware Guide Electrical and Reliability Features 5 5 2 Power Consumption The power consumptions of MC509 in different scenarios are respectively listed in Table 5 6 The power consumption listed in this section is tested when the power supply of MC509 module is 3 8V Typical values are measured at room temperature and minimum and maximum values are measured over the entire operating temperature range Table 5 6 Averaged standby DC power consumption Working mode Max Power off mode TBD pA Standby mode 800M TBD m Data mode 800M TBD m 1900M TBD m Um uA TED LL note e Standby current consumption with Sleep mode deactivated Idle assumes USB bus is fully suspended during measurements e The above values are the average of some test samples 5 6 Reliability Features Table 5 7 lists the test conditions and results of the mechanical reliability of the MC509 module Table 5 7 Test conditions and results of the mechanical reliability of the MC509 module Low temperature Temperature 40x2 C IEC60068 storage Test duration 2
80. s the safety period and the recyclability of the products The mark shown in the left figure is used by the products that are free of any toxic orhazardous substances or elements The mark shown in the right figure is used by products that contain toxic or hazardous substances or elements The user manuals of the products should indicate the names and contents of the toxic or hazardous substances or elements The number in the middle of the mark indicates the safety period of the specific product The safety period of a product will be determined in accordance with the General Guidelines of Environment Friendly Use Period of Electronic Information Products to be issued 7 3 7 Guide to Product Certification CE Certification and FCC Certification Huawei modules pass the RF EMC and safety specifications tests and obtain relevant certificates issued by notified certification bodies Huawei Proprietary and Confidential Ge Copyright Huawei Technologies Co Ltd 72 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications In the case of certification of the laptops installed with Huawei modules the relevant test reports of Huawei modules can be directly used in accordance with the following rules e The conductivity test data in the Huawei RF test report can be directly used by the laptop manufacturer e The laptop manufacturer should determine whether the radio test data in Huawei RF test report can be
81. s Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces 3 7 UIM Card Interface 3 7 1 Overview The MC509 module provides a UIM card interface complying with the ISO 7816 3 standard and supports automatic detection of a 3 0V UIM card or a 1 8V UIM card Table 3 11 lists the UIM card interface signals Table 3 11 UIM card interface signals Pin Name HO Description TIET GES ZE VE external UIM UM DATA Ju Extemal UIMdata 0 3 4 8 2 85 2 1 3 15 signal Wind CLK Extemal UIM lock 0 3 Ka 85 2 GE 15 signal ec UIM_RESET We External UIM reset inui We signal 3 7 2 Circuit Recommended for the UIM Card Interface As the MC509 module is not equipped with a UIM card socket a UIM card socket need to be placed on the user interface board The UIM card signals are transmitted outwards through the 145 pin LGA interface Figure 3 9 shows the circuit of the UIM card interface Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd He Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Figure 3 9 Circuit of the UIM card interface UIM Card Module D CE Figure 3 10 Pin definition of UIM Socket pin1 UIM PWR pin2 UIM RESET pin3 UIM CLK pin4 GND pin5 NULL pin6 UIM DATA Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyri
82. s of the UIM card interface For this reason the UIM card interface circuits need to be re tested The UIM test aims to verify the overall performance of UIM interface with appropriate test instruments in accordance with the relevant 3GPP protocol requirements Huawei provides a test report of the product to be certified for the customers who require the GCF certification The test report is issued by an organization designated for GCF certification The test report covers the Protocol Implementation Conformance Statement PICS and the test information on the product The PICS is a conformance statement of the product and a basis for GCF certification The test information includes the performed test items and results of the product The test organization can issue a certification report of the integrated equipment after performing the required field test and UIM test based on the test report provided by Huawei Terminal manufacturers who apply for the GCF certification of the terminals to be integrated with Huawei modules must accomplish the following tasks 1 Register as a member of the GCF The GCF certification is a DOC Only GCF members can submit their DOC on the GCF website Contact the GCF if you need to join the GCF Proceed with the following steps if you are a GCF member 2 Choose a test organization The GCF does not designate its test organizations All test organizations that meet the GCF test conditions can perform GCF tes
83. sed efficiently When the MC509 module is used for different external applications pay special attention to the design for the power supply When the MC509 module transmits signals at the maximum power the transient current may reach the transient peak value of about 1 5A due to the differences in actual network environments In this case the VBAT voltage drops Make sure that the voltage does not decrease below 3 3V in any case Otherwise exceptions such as restart of the MC509 module may occur A low dropout LDO regulator or switch power with current output of more than 1 5A is recommended for external power supply Furthermore a 220uF or above energy storage capacitor is connected in parallel at the power interface of the MC509 module Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd a Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces LL note For detailed information about power supply design and printed circuit board PCB design see the HUAWEI Module Power Supply Design Guide and the HUAWEI LGA Module PCB Interconnection Design Guide 3 3 3 VCOIN Interface VCOIN pin of MC509 module is used as backup power from the 3 V coin cell for SMPL RTC and 32 kHz crystal oscillator backup a capacitor rather than a coin cell can be used if only SMPL is supported Used as an analog output for coin cell or capacitor charging
84. t block diagram of the MC509 module The application block diagram and major functional units of the MC509 module contain the following parts e Qualcomm QSC chip e Multi chip package MCP memory e RF Circuit Figure 2 1 Circuit block diagram ofthe MC509 module VMEM RF Circuit LGA interface LL note Only telematics version supports the audio function Huawei Proprietary and Confidential Ge Copyright Huawei Technologies Co Ltd 11 Wis HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Overall Description 2 4 Application Block Diagram Figure 2 2 Application block diagram of the MC509 module Antenna Interface Application Interface LED Pawer or Restart Power off UART uim GPIO WS os p Reset Card _Sleep UART Interface The module supports 3 line or 5 line or full serial port interface USB Interface The USB interface supports USB 2 0 full speed standard UIM Interface The UIM interface provides the interface for a UIM card The UIM card can be inserted into the host side Power Supply DC 3 8V is recommended Audio Interface The module supports one speaker output two microphone one handset one speaker and one PCM interface only telematics version supports the audio function Huawei Proprietary and Confidential 42 EE Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces 3 Desc
85. ta only doesn t support the voice function Table 3 12 lists the signals on the digital audio interface Table 3 12 Signals on the digital audio interface Pin Name YO Description DC Characteristics V u PCM_SYNC o PCM interface sync 03 3 6 POM DN DIN PCMUFdatain I F data i PCM I F datain 0 3 3 8 Pom cik CLK O PCMinterface clock interface clock 0 3 3 The MC509 PCM interface enables communication with an external codec to support linear and law format The PCM SYNC runs at 8kHz with a 50 duty cycle Huawei Proprietary and Confidential 39 EE Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Figure 3 14 Circuit diagram of the interface of the PCM MC509 is used as PCM master Module DCE PCM SYNC a PCM SYNC oe PCM DIN d d PCM OUT PCM DOUT c PCM IN PCM_CLK PCM_CLK L note e PCM SYNC Output when PCM master e PCM CLK Output when PCM master e tis recommended that a TVS be used on the related interface to prevent electrostatic discharge and protect integrated circuit IC components e Data only edition does not support the voice function Primary Mode On Primary mode MU509 provides a 16 bit linear or u law with short sync and 2 048MHz clock on the PCM CLOCK pin 3 9 General Purpose I O Interface The LGA module provides
86. the MAIN_ANT pad the antenna interface is routed to the coaxial connector on the DTE Impedance 50 The external antenna is connected to the module through the coaxial connector A matching location for the antenna must be reserved at the antenna port Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd M Issue 01 2011 04 08 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Description of the Application Interfaces Description DC Characteristics V Table 3 13 Signals on RF Antenna interface MAIN ANT RF main antenna interface RF GPS antenna interface GPS ANT AUX ANT RF divert antenna interface 3 12 NC Pins The LGA module has 45 NC pins All the NC interfaces should not be connected Please keep this pin open Pin No Pin HO Description DC Characteristics V Name G 174 9 10 16 27 33 37 NC Not 47 60 70 82 84 92 94 connected 95 102 104 117 120 please keep this pin open Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd Issue 01 2011 04 08 TH ARAVA SCH PES HUAWEI Hardware Guide RF Specifications RF Specifications 4 1 About This Chapter This chapter describes the RF specifications of the MC509 module including Antenna Installation Guidelines Operating Frequencies Conducted RF Measurement Conducted Rx Sensitivity and Tx Power Antenna Design Requirements 4 2 Antenna Installation Guide
87. therein HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide About This Document About This Document History Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide About This Document Summary This document provides information about the major functions supported services system architecture and technical references of HUAWEI MC509 CDMA LGA Module e Packing System e Certifications e Environmental Protection Certification and Test e National Compulsory Certification The following table lists the contents of this document Chapter 1 Introduction 2 Overall Description 3 Description of the Application Interfaces 4 RF Specifications 5 Electrical and Reliability Features 6 Mechanical Specifications 7 Certifications 8 Safety Information 9 Appendix A Circuit of Typical Interfacesl 10 Appendix B Acronyms and Abbreviations Describes the short introduction of the product Describes the Function overview Circuit Block Diagram and Application Block Diagram of the product Describes the external application interfaces of the product Describes the RF specifications of the product Describes the electrical and reliability features of the interfaces in the product Describes the Dimensions Label and Packing System of the product Describes the certifications of the product Lists the safety info
88. ts In this case it is necessary for manufacturers to choose a well recognized test organization that provides high quality and high efficiency services The global test organizations Tlayers SGS and CETCOM are recommended The recommended test organizations have built various labs all around the world and work closely with Huawei Proprietary and Confidential EE Copyright Huawei Technologies Co Ltd 76 4 HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications the GCF and the PTCRB Therefore the test organizations are able to provide high quality and high efficiency test services and are widely recognized by operators 3 Discuss test details with the test organization Provide the test organization with the test report of Huawei modules and the modifications of the integrated equipment The test organization then can determine the detailed test items and determine the test schedule accordingly With the detailed test items and schedule terminal manufacturers can determine accurate plans of product development and marketing 4 Perform overall system certification The integrated equipment can pass the over all certification test easily if Huawei s design suggestions are complied with 5 Obtain the test report and the DOC The test report describes the details about the overall system test that operators are concerned about The GCF certification is completed upon uploading of the DOC to the GCF website
89. used according to the antenna gain The radio test data in Huawei RF test report can be directly used if the antenna gain of the laptop is lower than that used in the certification test of Huawei modules The laptop manufacturer should test antennas of the laptops if the antenna gain of the laptop is higher than that used in the certification test of Huawei modules e Thelaptop manufacturer should test the compliance of the laptops with EMC and safety specifications e The SAR of the laptops needs to be tested only if the antennas of the laptops are within 20 cm of people IC Certification Huawei applies for IC certificate to the relevant certification bodies by using an IC test report converted from the FCC test report NCC Certification Huawei mails a sample module to the ADT of Taiwan The ADT then performs relevant tests and issues an NCC certificate 7 4 GCF and PTCRB Conformance test and declaration are required for establishing that the GSM and WCDMA terminals to be sold in a region meet the requirements of the local carriers and networks Global Certification Forum GCF and PTCRB certifications are recognized in most regions all around the world Most operators all round the world accept either certification as one of the market entry conditions 7 4 1 GCF Certification The GCF is an active partnership between European mobile device manufacturers and mobile network operators According to the R amp TTE Directiv
90. xing a certification mark to a product the manufacturer declares that the prod ct is compliant with the relevant certification standards For example a manufacturer declares that its product complies with relevant EU directives if it affixes a CE mark to the product NB certification By affixing a certification mark issued by an authorized certification body to a product the manufacturer declares that the product passes the NB certification tests and complies with the relevant certification standards The CE0682 mark issued by CETECOM the UL mark issued by UL and the GS mark issued by TUV Rheinland are three examples of NB certification marks NB certification is used for Huawei modules in most cases Issue 01 2011 04 08 Huawei Proprietary and Confidential Copyright Huawei Technologies Co Ltd SS Wis HUAWEI MC509 CDMA LGA Module HUAWEI Hardware Guide Certifications 7 3 6 Certification Types CE Certification According to the R amp TTE Directive 1999 95 EC all wireless equipment and telecommunications terminals sold in EU must meet all the stipulated health safety RF and EMC requirements that provide for CE mark Wireless equipment using frequency bands whose use is not harmonized throughout the EU should pass the certification test of a notified body Notification should be given no less than four weeks in advance of the start of placing on the market and should provide information about the radio characteristics

Huawei MC509 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents