Home

HP Printer PCLA8205B User's Manual

1. dialog box Windows 95 SR2 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 Intel EtherExpress PRO 10 ISA Ethernet card and drivers disk Driver Name PROW95 VXD Size 6K Date 8 7 96 Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA adapter card into an ISA slot 2 Connect network cable media to the Intel EtherExpress PRO 10 ISA card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the Intel EtherExpress drivers disk EtherExpress drivers Ver 3 5 and execute A SOFTSET2 EXE 5 Select Configure NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the Intel EtherExpress software driver diskette and reboot the machine Power on the machine and allow it to boot to Windows 95 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 If you are using a Vectra VE7 VE8 foll
2. Continue in the second Network Adapter Card Detection dialog box 13 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 14 Set the path to A NT in the Insert Disk dialog box and insert the Intel EtherExpress drivers disk f you have an HP preloaded HDD set path to C Masters LanDrv PRO10 NT 15 Click OK at the Install Driver dialog box 16 Select Intel EtherExpress TM PRO 10 or PRO ISA LAN Adapter in the Select OEM Option dialog box and click OK 17 Click on the OK button in the Intel PROSet dialog box 18 Choose the default Protocol TCP IP and any additional network protocols by clicking the check boxes in the Windows NT Setup dialog box and click OK If you do not have the required information contact your network administrator 19 Check the box to add other TCP IP components and hit Enter 20 MClick OK to review the network settings in the Network Settings dialog box 21 Enter your IP information or check the box Enable Automatic DHCP Configuration and click on the OK button If you do not have the required information contact your network administrator 22 At the Domain Workgroup Settings Dialog Box click on OK to accept the default Workgroup as your workgroup name If you do not have the required inform
3. If you do not have the re quired information contact your network administrator Click on the OK button approve the basic configuration and files will copy When prompted for the file NETAPI DLL set the path to your Win dows 95 files and click on OK If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs Click on the Yes button to finish the installation and restart your com puter 9 When Windows 95 restarts a message will appear to indicate that new hardware has been found 10 Click on Next to continue installation then insert the Intel EtherExpress drivers disk 11 Click on Other Locations set the path to A and click on Finish If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 12 When prompted for the file EPRONDI DLL with the Intel EtherExpress drivers disk inserted set the path to A and click OK If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 13 Click OK to the Network dialog box to provide computer work group 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 names 14 Specify your Computer Name Workgroup and Computer Description If you do not have the required information contact your network administrator 15 Click on Close button and files will copy 16 When prompted for the file NETAPI DLL set the path to your Wind
4. then go to step 18 a Insert Netware Client for DOS and Windows Disk 1 and execute A IN STALL b Change the settings to match the following and then option 6 to con tinue the installation e CANWCLIENT e YES e YES e C WINDOWS e No e Intel EtherExpress Pro 10 LAN Adapter Use the driver from the drivers disk at A c Insert the corresponding diskettes to finish the file transfer and then reboot the machine 9 Accept the default products by pressing enter and then press F10 to continue 10 Select 16 bit LAN Drivers and hit the enter key 11 Page down the Board Drivers list to USER SPECIFIED 16 BIT DRIVER and hit enter 12 Insert the Intel ethernet drivers diskette set the path to A DOS and press enter 13 Select Intel EtherExpress PRO 10 and press enter 14 Accept the default settings press F10 to continue and verify the following entries for the Installation Configuration Summary O YES 2 Connecting to a Netware 4 11 Server Windows for Workgroups Version 3 11 O CANOVELL CLIENT32 O CAWINDOWS O 16 bit LAN drivers O Intel EtherExpress PRO 10 15 Press F10 to save and continue 16 When prompted insert the corresponding disks to complete file transfer and driver installation 17 When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine 18 After Windows loads open the NETWORK folder
5. C Masters Win95 System Cabs Click on the Yes button to finish the installation and restart your com puter 9 When Windows 95 restarts a message will appear to indicate that new hardware has been found 10 Click on Next to continue installation then insert the Intel EtherExpress drivers disk 11 Click on Other Locations set the path to A and click on Finish If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 12 When prompted for the file EPRONDI DLL with the Intel EtherExpress drivers disk inserted set the path to A and click OK If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 2 Connecting to a Netware 4 11 Server Windows 95 SR2 13 Click OK to the Network dialog box to provide computer work group names 14 Specify your Computer Name Workgroup and Computer Description If you do not have the required information contact your network administrator 15 Click on Close button and files will copy 16 When prompted for the file NETAPI DLL set the path to your Windows 95 files and click OK For HP preloaded HDD s set the path to C WIN95 SR2 17 Click on the Yes button to finish the installation and restart your computer 2 Connecting to a Netware 4 11 Server Windows 95 SR2 Windows for Workgroups Version 3 11 3 Connecting to a Windows NT Server 3 51 Windows
6. Ethernet adapter card and drivers disk Vectra VL8 and VLT Driver Name EPRO 386 Size 16K Date 10 22 96 Vectra VE7 VE8 Driver Name EEPRODLINS Size 784B Date 10 26 95 Novell Netware 4 1 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Netware Client for DOS and MS Windows Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 16 bit only 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA Ethernet adapter card into an ISA slot Connect network cable media to the Intel EtherExpress card Power on the machine After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE Select Change Adapter configuration and verify the resource settings 2 Connecting to a Netware 4 11 Server Windows for Workgroups Version 3 11 listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the Intel drivers diskette insert Netware client for DOS and MS Windows disk 1 8 Execute INST_DOS EXE and enter yes to accept the agreement if using a Vectra VL8 then continue to step 9 If using a Vectra VL7 or VE7 VE8 follow the instructions below
7. Masters LanDrv Pro10 12 When prompted for the file EPRONDI DLL with the Intel EtherExpress drivers disk inserted set the path to A and click OK If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 13 Click OK to the Network dialog box to provide computer work group names 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 14 Specify your Computer Name Workgroup and Computer Description If you do not have the required information contact your network administrator 15 Click on Close button and files will copy 16 When prompted for the file NETAPI DLL set the path to your Windows 95 files and click OK For HP preloaded HDD s set the path to C WIN95 SR2 17 Click on the Yes button to finish the installation and restart your computer 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Windows NT Workstation Version 3 51 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 Requirements HP Vectra with Microsoft Windows NT Workstation 3 51 installed Intel EtherExpress Pro 10 ISA Ethernet card and drivers disk Ver 3 5 Driver Name EPRO SYS Size 10KB Date 4 14 97 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vect
8. and double click the NETWORK SETUP icon 19 Select the Networks button in the Network Setup and verify that Novell NetWare Workstation Shell 4 0 and above is listed under Install Windows Support for the following network only 20 Click on OK twice to complete the installation 2 Connecting to a Netware 4 11 Server Windows for Workgroups Version 3 11 Windows 95 SR2 2 Connecting to a Netware 4 11 Server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed Intel EtherExpress Pro 10 ISA Ethernet card and drivers disk Ver 3 5 Vectra VL8 and VE7 VE8 Driver Name NETPRO INF Size 12KB Date 4 25 97 Vectra VL7 Driver Name EPRO SYS Size 11KB Date 6 3 97 Novell Netware 3 12 server that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress Prol0 ISA adapter card into an ISA slot Connect network Cable media to the Intel EtherExpress ISA card Insert a DOS bootable diskette and power on the machine After booting insert the Intel EtherExpress drivers disk EtherExpress drivers Ver 3 5 and execute
9. and double click the Network Icon 11 Click on the Yes button and agree to install Windows NT Networking 12 With Wired to the Network checked click on Next 13 Click on the option to Select from list then on Have Disk 14 Insert the Intel EtherExpress PRO 10 ISA Ethernet drivers disk ver 3 5 into the floppy drive 15 With the path set to AANT click OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV PRO10 NT 16 Select Intel EtherExpress TM PRO 10 ISA LAN Adapter and click OK 17 With Intel EtherExpress TM PRO 10 ISA LAN Adapter listed in the Network Adapters window click on NEXT 18 Accept the applicable Network Protocols and click on Next If you do not have the required information contact your network administrator 19 At the Network Services prompt accept default settings and click on Next 20 Finish the network card installation by clicking on Next 21 Designate the path to your NT files and select Continue If you have a Hewlett Packard preloaded HDD set the path to C I886 22 Click on OK for Intel PROSet dialog box 23 Click on Yes to use DHCP or choose NO if you know your IP address If you do not have the required information contact your network administrator 24 At the Show Bindings for prompt a
10. for Workgroups Version 3 11 3 Connecting to a Windows NT Server 3 51 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed Intel EtherExpress Pro 10 ISA Ethernet adapter card and drivers disk Ver 3 5 Driver Name EPRO 386 Size 16K Date 10 22 96 Microsoft Windows NT server 3 51 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO ISA Ethernet adapter card into an ISA slot 2 Connect network Cable Media to the Intel EtherExpress card 3 Power on the machine 4 After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE 5 Select Change Adapter configuration and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit Windows for Workgroups Version 3 11 7 Remove the Intel drivers diskette and reboot the machine 8 After Windows loads open the NETWORK program group and double click the Network Setup 9 Select the Networks button in the Network Setup dialog
11. lt DEL gt to restart the machine 18 After Windows loads open the NETWORK folder and double click the NETWORK SETUP icon 19 Select the Networks button in the Network Setup and verify that Novell NetWare Workstation Shell 4 0 and above is listed under Install Windows Support for the following network only 20 Click on OK twice to complete the installation 1 Connecting to a Netware 3 12 Server Windows for Workgroups Version 3 11 Windows 95 SR2 1 Connecting to a Netware 3 12 Server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed Intel EtherExpress Pro 10 ISA Ethernet card and drivers disk Driver Name for Vectra VL8 and VE7 VE8 NETPRO INF Size 12KB Date 4 25 97 Driver Name for Vectra VLT EPRO SYS Size 11KB Date 6 3 97 Novell Netware 3 12 server that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress Prol0 ISA adapter card into an ISA slot Connect network Cable media to the Intel EtherExpress ISA card Insert a DOS bootable diskette and power on the machine After booting
12. new hardware has been found 10 Click on Next to continue installation then insert the Intel EtherExpress drivers disk 11 Click on Other Locations set the path to A and click on Finish If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 12 When prompted for the file EPRONDI DLL with the Intel EtherExpress drivers disk inserted set the path to A and click OK If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 13 Click OK to the Network dialog box to provide computer work group names 14 Specify your Computer Name Workgroup and Computer Description If you do not have the required information contact your network administrator 1 Connecting to a Netware 3 12 Server Windows 95 SR2 15 Click on Close button and files will copy 16 When prompted for the file NETAPI DLL set the path to your Windows 95 files and click OK For HP preloaded HDD s set the path to C WIN95 SR2 17 Click on the Yes button to finish the installation and restart your computer 1 Connecting to a Netware 3 12 Server Windows 95 SR2 Windows for Workgroups Version 3 11 2 Connecting to a Netware 4 11 Server Windows for Workgroups Version 3 11 2 Connecting to a Netware 4 11 Server Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed Intel EtherExpress Pro 10 ISA 10MBS
13. resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the Intel drivers diskette and reboot the machine After Windows loads go to the MAIN program group and double click 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 on Control Panel 9 Select the Network icon and click YES to install NT networking 10 Insert the Windows NT Workstation CD 11 In the Windows NT Setup set the path to your NT files and click on the Continue button If you have an HP preloaded HDD set path to C I386 12 Click on the Do Not Detect button from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box 13 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 14 Set the path to A NT in the Insert Disk dialog box and insert the Intel EtherExpress drivers disk If you have an HP preloaded HDD set path to C Masters LanDrv PRO10 NT 15 Click OK at the Install Driver dialog box 16 Select Intel EtherExpress TM PRO 10 or PRO ISA LAN Adapter in the Select OEM Option dialog box and click OK 17 Click on the OK button in the Intel PROSet dialog box 18 Choose t
14. A SOFTSET2 EXE Select Configure NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the Intel EtherExpress software driver diskette and reboot the machine 2 Connecting to a Netware 4 11 Server Windows 95 SR2 8 Power on the machine and allow it to boot to Windows 95 SR2 If you are using a Vectra VE7 VE8 follow the instructions below to complete the procedure If you are using a VL8 or VL7 go directly to step 9 a b Q a Click on Start then Settings and open the Control Panel Double click on the Network icon and click on Add Select Adapter and click on Add Click on Have Disk insert the Intel Etherexpress Pro10 drivers disk and set the path to A df you have an HP preloaded HDD set path to C Masters LanDrv Pro10 Click on OK and select the Intel EtherExpress PRO 10 and hit enter With the Intel Etherexpress PRO10 listed in the Network window click on the Identification folder and specify your Computer Name Workgroup and Computer Description If you do not have the re quired information contact your network administrator Click on the OK button approve the basic configuration and files will copy When prompted for the file NETAPI DLL set the path to your Win dows 95 files and click on OK If you have an HP preloaded HDD the media is located at
15. Ethernet adapter card into an ISA slot 2 Connect network Cable Media to the Intel EtherExpress card 3 Power on the machine 4 After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE 5 Select Change Adapter configuration and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Version 3 11 7 Remove the Intel drivers diskette and reboot the machine 8 After Windows loads open the NETWORK program group and double click the Network Setup 9 Select the Networks button in the Network Setup dialog box 10 Click on the Install Microsoft Windows Network option and click OK 11 Click the Drivers button from the Network Setup dialog box and click on Add Adapter 12 Click OK to accept the default choice of Unlisted or Updated Network Adapter 13 Type the path A WFW in the Install Driver dialog box and then insert the Intel EtherExpress drivers disk into the floppy drive and click OK f you have an HP preloaded HDD set path to C Masters LanDrv Prol0 WFW For Vectra VE7 VE8 users the path is C Masters LanDrv Prol00P WFW 14 Select Intel EtherExpress TM PRO 10 LAN Adapter in the Unlisted or Updated Network Adapter dialog b
16. Kin HEWLETT PACKARD EtherExpress Pro 10 ISA PCLA8205B Installation Guide Notice The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Hewlett Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett Packard This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation MMXIM is a trademark of Intel Corporation Pentium is a registered trademark of Intel Corporation Hewlett Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France 1998 Hewlett Packard Company Windows for Workgroups Version 3 11 1 Connecting to a Netware 3 12 Server Windows for Workgroups Version 3 11 1 Connecting to a Netware 3 12 Server Requirements HP Vectra with DOS and M
17. Next If you do not have the required information contact your network administrator 19 At the Network Services prompt accept default settings and click on Next 20 Finish the network card installation by clicking on Next 21 Designate the path to your NT files and select Continue If you have a Hewlett Packard preloaded HDD set the path to C M386 22 Click on OK for Intel PROSet dialog box 23 Click on Yes to use DHCP or choose NO if you know your IP address If you do not have the required information contact your network administrator 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 24 At the Show Bindings for prompt accept default settings and click on Next 25 When Windows NT is now ready to start the network click on Next 26 Specify your Computer Name Workgroup or Domain and click on Next If you do not have the required information contact your network administrator 27 After Network has been installed on this computer click on Finish 28 To complete the installation select Yes to reboot your computer 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 Version Number Intel Prol0 Rev 1
18. S Windows for Workgroups 3 11 installed Intel EtherExpress Pro 10 ISA 10MBS Ethernet adapter card and drivers disk Vectra VL8 and VL7 Driver Name EPRO 386 Size 16K Date 10 22 96 Vectra VE7 VE8 Driver Name EPROODL INS Size 784B Date 10 26 95 Novell Netware 3 12 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Netware Client for DOS and MS Windows Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 16 bit only 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA Ethernet adapter card into an ISA slot Connect network cable media to the Intel EtherExpress card Power on the machine After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE Select Change Adapter configuration and verify the resource settings 1 Connecting to a Netware 3 12 Server Windows for Workgroups Version 3 11 listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the Intel drivers diskette insert Netware client for DOS and MS Windows disk 1 8 Execute INST_DOS EXE If you are using a Vectra VL8 enter yes to accept the agreement a
19. aded HDD the media is located at C I386 Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA Ethernet adapter card into an ISA slot 2 Connect network cable media to the Intel EtherExpress PRO ISA Ethernet adapter card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE 5 Select Change Adapter configuration and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 4 0 7 Remove the Intel drivers diskette and reboot the machine 8 Power on the machine and allow it to boot to Windows NT Workstation 4 0 9 Log onto the machine with administrator privileges If you do not have the required information contact your network administrator 10 Click on Start and move to Settings open the Control Panel group
20. ation contact your network administrator 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 23 To complete the installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking Setup dialog box Windows NT Workstation 4 0 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 Requirements HP Vectra with Windows NT Workstation 4 0 Service Pack 3 Intel EtherExpress PRO 10 ISA Ethernet card and drivers disk ver 3 5 Driver Name EPRO SYS Size 11KB Date 4 14 97 Microsoft Windows NT Workstation 4 0 and Service Pack Media f you have a Hewlett Packard preloaded HDD the media is located at C I386 Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA Ethernet adapter card into an ISA slot 2 Connect network cable media to the Intel EtherExpress PRO ISA Ethernet adapter card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the Intel EtherExpress drivers dis
21. box 10 Click on the Install Microsoft Windows Network option and click OK 11 Click the Drivers button from the Network Setup dialog box and click on Add Adapter 12 Click OK to accept the default choice of Unlisted or Updated Network Adapter 13 Type the path A WFW in the Install Driver dialog box and then insert the Intel EtherExpress drivers disk into the floppy drive and click OK If you have an HP preloaded HDD set path to C Masters LanDrv Prol0 WFW For Vectra VE7 VE8 users the path is C Masters LanDrv Prol0P WFW 14 Select Intel EtherExpress TM PRO 10 LAN Adapter in the Unlisted or Updated Network Adapter dialog box and click OK 15 Click OK in the Intel EtherExpress TM PRO 10 LAN Adapter dialog box to confirm the interrupt Base I O the Transceiver Type Link Speed Power Management AllFramesCRT DynamicCRTMax DynamicCRTIncrement and the DynamicCRTInterval settings 16 Make sure that the Intel EtherExpress TM PRO 10 LAN Adapter NDIS2 NDIS3 is selected in Network Drivers 17 Accept the list of Protocols listed below and click on the CLOSE button O Intel EtherExpress PRO 10 LAN Adapter NDIS2 NDIS3 O Microsoft NetBEUI O IPX SPX Compatible Transport with NetBIOS If you do not have the required information contact your network ad ministrator 18 At the Network Setup dialog box c
22. ccept default settings and click on Next 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 4 0 25 When Windows NT is now ready to start the network click on Next 26 Specify your Computer Name Workgroup or Domain and click on Next If you do not have the required information contact your network administrator 27 After Network has been installed on this computer click on Finish 28 To complete the installation select Yes to reboot your computer 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 4 0 Windows for Workgroups Version 3 11 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Version 3 11 4 Connecting to a Windows NT Server 4 0 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed Intel EtherExpress Pro 10 ISA Ethernet adapter card and drivers disk Ver 3 5 Driver Name EPRO 386 Size 16K Date 10 22 96 Microsoft Windows NT server 4 0 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO ISA
23. he default Protocol TCP IP and any additional network protocols by clicking the check boxes in the Windows NT Setup dialog box and click OK if you do not have the required information contact your network administrator 19 Check the box to add other TCP IP components and hit Enter 20 Click OK to review the network settings in the Network Settings dialog box 21 Enter your IP information or check the box Enable Automatic DHCP Configuration and click on the OK button If you do not have the required information contact your network administrator 22 At the Domain Workgroup Settings Dialog Box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 23 To complete the installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 Setup dialog box Windows NT Workstation Version 4 0 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 4 0 Requirements HP Vectra with Windows NT Workstation 4 0 Service Pack 3 Intel EtherExpress PRO 10 ISA Ethernet card and drivers disk Driver Name EPRO SYS Size 11KB Date 4 14 97 Microsoft Windows NT Workstation 4 0 and Service Pack Media If you have a Hewlett Packard prelo
24. insert the Intel EtherExpress drivers disk EtherExpress drivers Ver 3 5 and execute A SOFTSET2 EXE Select Configure NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the Intel EtherExpress software driver diskette and reboot the machine 1 Connecting to a Netware 3 12 Server Windows 95 SR2 8 Power on the machine and allow it to boot to Windows 95 SR2 If you are using a Vectra VL8 or VL7 go directly to step 9 If you are using a Vectra VE7 VE8 follow the instructions below and then go to step 16 a Click on Start then Settings and open the Control Panel b Double click on the Network icon and click on Add Select Adapter and click on Add d Click on Have Disk insert the Intel Etherexpress Prol0 drivers disk and set the path to A df you have an HP preloaded HDD set path to C Masters LanDrv Pro10 e Click on OK and select the Intel EtherExpress PRO 10 and hit enter f With the Intel Etherexpress PRO10 listed in the Network window click on the Identification folder and specify your Computer Name Workgroup and Computer Description If you do not have the re quired information contact your network administrator g Click onthe OK button approve the basic configuration and files will copy 9 When Windows 95 restarts a message will appear to indicate that
25. k Ver 3 5 and execute A SOFTSET2 EXE 5 Select Change Adapter configuration and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 7 Remove the Intel drivers diskette and reboot the machine 8 Power on the machine and allow it to boot to Windows NT Workstation 4 0 9 Log onto the machine with administrator privileges If you do not have the required information contact your network administrator 10 Click on Start and move to Settings open the Control Panel group and double click the Network Icon 11 Click on the Yes button and agree to install Windows NT Networking 12 With Wired to the Network checked click on Next 13 Click on the option to Select from list then on Have Disk 14 Insert the Intel EtherExpress PRO 10 ISA Ethernet drivers disk ver 3 5 into the floppy drive 15 With the path set to AANT click OK If you have a Hewlett Packard preloaded HDD set the path statement to CAMASTERS LANDRV PRO10NTV 16 Select Intel EtherExpress TM PRO 10 ISA LAN Adapter and click OK 17 With Intel EtherExpress TM PRO 10 ISA LAN Adapter listed in the Network Adapters window click on NEXT 18 Accept the applicable Network Protocols and click on
26. lick on OK 19 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Version 3 11 20 When prompted for the file EPRO DOS insert the Intel EtherExpress drivers disk Ver 3 5 and set the path to A NDIS If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 NDIS For Vectra VE7 VE8 users the path is C Masters LanDrv Prol0P WFW 21 Finish the network card installation by clicking on OK in the Network Setup message 22 To complete the installation click on Restart Computer button in the Windows Setup dialog box Windows for Workgroups Version 3 11 Windows 95 SR2 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 Intel EtherExpress PRO 10 ISA Ethernet card and drivers disk Driver Name PROW95 VXD Size 6K Date 8 7 96 Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only e Board Connector type Auto detect e Force 8 bit operation Yes e Flash chip address Disabled e Remote boot program None Procedure 1 With the HP Vectra turned off ins
27. nd then continue from step 9 If you are using a Vectra VL7 or VE8 follow the steps below and then continue from step 16 a Specify the settings as listed below e CANWCLIENT e Yes e Yes e C WINDOWS e No e Intel Etherexpress PRO 10 LAN Adapter b Under the heading Select the driver for your network board insert the Intel Etherexpress PRO 10 drivers disk and set the path to A DOS If you have an HP preloaded HDD set path to C Mas ters LanDrv PRO10P DOS c Press Enter to continue the installation 9 Accept the default products by pressing enter and then press F10 to continue 10 Select 16 bit LAN Drivers and hit the enter key 11 Page down the Board Drivers list to USER SPECIFIED 16 BIT DRIVER and hit enter 12 Insert the Intel ethernet drivers diskette set the path to A DOS and press enter 13 Select Intel EtherExpress PRO 10 and press enter 14 Accept the default settings press F10 to continue and verify the following entries for the Installation Configuration Summary O YES 1 Connecting to a Netware 3 12 Server Windows for Workgroups Version 3 11 O CANOVELL CLIENT32 O CAWINDOWS O 16 bit LAN drivers O Intel EtherExpress PRO 10 15 Press F10 to save and continue 16 When prompted insert the corresponding disks to complete file transfer and driver installation 17 When the install utility is finished press lt CRTL gt lt ALT gt
28. ow the instructions below to complete the installation If not go directly to step 9 a b fe a Click on Start then Settings and open the Control Panel Double click on the Network icon and click on Add Select Adapter and click on Add Click on Have Disk insert the Intel Etherexpress Pro10 drivers disk and set the path to A df you have an HP preloaded HDD set path to C Masters LanDrv Pro10 Click on OK and select the Intel EtherExpress PRO 10 and hit enter With the Intel Etherexpress PRO10 listed in the Network window click on the Identification folder and specify your Computer Name Workgroup and Computer Description If you do not have the re quired information contact your network administrator Click on the OK button approve the basic configuration and files will copy When prompted for the file NETAPI DLL set the path to your Win dows 95 files and click on OK If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs Click on the Yes button to finish the installation and restart your com puter 9 When Windows 95 restarts a message will appear to indicate that new hardware has been found 10 Click on Next to continue installation then insert the Intel EtherExpress drivers disk 11 Click on Other Locations set the path to A and click on Finish If you have an HP preloaded HDD set path to C
29. ows 95 files and click OK For HP preloaded HDD s set the path to C WIN95 SR2 17 Click on the Yes button to finish the installation and restart your computer 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 Windows NT Workstation Version 3 51 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 Requirements HP Vectra with Microsoft Windows NT Workstation 3 51 installed Intel EtherExpress Pro 10 ISA Ethernet card and drivers disk Driver Name EPRO SYS Size 10KB Date 4 14 97 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 210 21Fh 300 30Fh Interrupt 10 10 11 16 bit only Board Connector type Auto detect Force 8 bit operation Yes Flash chip address Disabled Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA Ethernet adapter card into an ISA slot Connect network cable media to the Intel EtherExpress PRO 10 ISA Ethernet adapter card Insert a DOS bootable diskette and power on the machine After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE Select Change Adapter configuration and verify the
30. ox and click OK 15 Click OK in the Intel EtherExpress TM PRO 10 LAN Adapter dialog box to confirm the interrupt Base I O the Transceiver Type Link Speed Power Management AllFramesCRT DynamicCRTMax DynamicCRTIncrement and the DynamicCRTInterval settings 16 Make sure that the Intel EtherExpress TM PRO 10 LAN Adapter NDIS2 NDIS3 is selected in Network Drivers 17 Accept the list of Protocols listed below and click on the CLOSE button O Intel EtherExpress PRO 10 LAN Adapter NDIS2 NDIS3 O Microsoft NetBEUI O IPX SPX Compatible Transport with NetBIOS If you do not have the required information contact your network ad ministrator 18 At the Network Setup dialog box click on OK 19 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Version 3 11 20 When prompted for the file EPRO DOS insert the Intel EtherExpress drivers disk Ver 3 5 and set the path to A NDIS If you have an HP preloaded HDD set path to C Masters LanDrv Pro10 NDIS For Vectra VE7 VE8 users the path is C Masters LanDrv Prol00P WFW 21 Finish the network card installation by clicking on OK in the Network Setup message 22 To complete the installation click on Restart Computer button in the Windows Setup
31. ra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Address 210 21Fh 21 21Fh 300 30Fh Interrupt 10 10 11 16 bit only Board Connector type Auto detect Force 8 bit operation Yes Flash chip address Disabled Remote boot program None Procedure 1 With the HP Vectra turned off install the Intel EtherExpress PRO 10 ISA Ethernet adapter card into an ISA slot Connect network cable media to the Intel EtherExpress PRO 10 ISA Ethernet adapter card Insert a DOS bootable diskette and power on the machine After booting insert the Intel EtherExpress drivers disk Ver 3 5 and execute A SOFTSET2 EXE Select Change Adapter configuration and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the Intel drivers diskette and reboot the machine After Windows loads go to the MAIN program group and double click 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 on Control Panel 9 Select the Network icon and click YES to install NT networking 10 Insert the Windows NT Workstation CD 11 In the Windows NT Setup set the path to your NT files and click on the Continue button If you have an HP preloaded HDD set path to C 386 12 Click on the Do Not Detect button from the Network Adapter Card Detection dialog box and click on
32. tall the Intel EtherExpress PRO 10 ISA adapter card into an ISA slot 2 Connect network cable media to the Intel EtherExpress PRO 10 ISA card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the Intel EtherExpress drivers disk EtherExpress drivers Ver 3 5 and execute A SOFTSET2 EXE 5 Select Configure NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the Intel EtherExpress software driver diskette and reboot the machine Power on the machine and allow it to boot to Windows 95 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 If you are using a Vectra VE7 VE8 follow the instructions below to complete the procedure If you are using a VL8 or VL7 go directly to step 9 a b lo a Click on Start then Settings and open the Control Panel Double click on the Network icon and click on Add Select Adapter and click on Add Click on Have Disk insert the Intel Etherexpress Pro10 drivers disk and set the path to A df you have an HP preloaded HDD set path to C Masters LanDrv Pro10 Click on OK and select the Intel EtherExpress PRO 10 and hit enter With the Intel Etherexpress PRO10 listed in the Network window click on the Identification folder and specify your Computer Name Workgroup and Computer Description

HP Printer PCLA8205B User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents