HP NC373F User's Manual
Contents
1. Each laser product complies with 21 CFR 1040 10 and 1040 11 except for deviations pursuant to Laser Notice No 50 dated May 27 2001 and with IEC 60825 1 1993 A2 2001 A WARNING Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product s installation guide may result in hazardous radiation exposure To reduce the risk of exposure to hazardous radiation e Do not try to open the module enclosure There are no user serviceable components inside e Do not operate controls make adjustments or perform procedures to the laser device other than those specified herein e Allow only HP Authorized Service technicians to repair the unit The Center for Devices and Radiological Health CDRH of the U S Food and Drug Administration implemented regulations for laser products on August 2 1976 These regulations apply to laser products manufactured from August 1 1976 Compliance is mandatory for products marketed in the United States Regulatory compliance notices 13 Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycl2. component or assembly Grounding methods to prevent electrostatic discharge Several methods are used for grounding Use one or more of the following methods when handling or installing electrostatic sensitive parts e Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis Wrist straps are flexible straps with a minimum of 1 megohm 10 percent resistance in the ground cords To provide proper ground wear the strap snug against the skin e Use heel straps toe straps or boot straps at standing workstations Wear the straps on both feet when standing on conductive floors or dissipating floor mats e Use conductive field service tools e Use a portable field service kit with a folding static dissipating work mat If you do not have any of the suggested equipment for proper grounding have an authorized reseller install the part For more information on static electricity or assistance with product installation contact an authorized reseller Electrostatic discharge 15 Acronyms and abbreviations ACPI Advanced Configuration and Power Interface APM advanced power management CSA Canadian Standards Association DMA direct memory access IEEE Institute of Electrical and Electronics Engineers C35 Internet Small Computer System Interface MDI X medium dependent interface crossover PCI Express Peripheral Component Interconnect Express RDMA Remote Direct Me
3. HP NC373F PCI Express Multitunction Gigabit Server Adapter User Guide en os Part Number 417728 O00B June 2007 Second Edition Copyright 2006 2007 Hewlett Packard Development Company L P The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein Audience assumptions This document is for the person who installs administers and troubleshoots servers and storage systems HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels Contents DUI AMIN NI E P AE OE EOE WOE ales ged AAI IAA Sores nc mes IA uated nese ae 4 Wh refo go for additional hel omer etre meer et anne cine a eT perenne Wit meena ae ca mena rene nner 4 FAP contact intotmMatiON sesse ounce senna tia vanes ouie iia Ea E NEEE e E E NEEM rmaanAe NEAR 5 co 51 eee ee Eee eee ene E E Tet TNT Unt mtr meres rome E EE A E A I crt E ereerrrms restore crt rer ttt 6 OVE IVI OW esr e E E E E E 6 DE DAI Eee RE EAE E A T E E TE 7 hstallingan I oeseri rrr ESE SEE 8 Installation OVEniEWsersssrsssasenni a eE E E iA a Vea A N ERER EER a E EE 8 Preventing electrostatic discharge ss
4. adapter and how to connect the network cable Z WARNING To reduce the risk of personal injury or damage to the equipment consult the safety information and user documentation provided with the server before attempting the installation Many servers are capable of providing energy levels that are considered hazardous and are intended to be serviced only by qualified personnel who have been trained to deal with these hazards Do not remove enclosures or attempt to bypass any interlocks that may be provided for the purpose of removing these hazardous conditions WARNING Installation of this adapter should be performed by individuals who are both p p y qualified in the servicing of computer equipment and trained in the hazards associated with products capable of producing hazardous energy levels This adapter is intended to be installed in Certified UL or CSA ITE equipment having instructions for adding and removing user installed components such as PCI PCI X and PCI Express devices Refer to the equipment instructions to verify that it is suitable for user installed components and that it has the power capacity to support all of the installed components NOTE Before removing the cover of your server refer to the HP documentation for the proper methods for installing a PCI card and avoiding electric shock hazards Preventing electrostatic discharge To prevent damaging the system be aware of the precautions you need to follow when set
5. aiasisistenenecsiuaiasnduneevejad dap tentuneeieyataaipiudevonin iad apres seertuaGudssueeereranssuiued 15 Grounding methods to prevent electrostatic discharge cscccssceccesseeeeneeeeesceeeeeeceneceeneseeceaeeceeeeenereeenaeeenaes 15 Acronyms and a bbrevidh ons simsimrininieiierinininr nanninannan EA AANE EAA AAE RERA AAAA AAAA 16 LL Neen I DEER See A E ON E SEOs ERNEST Ioan SOI RE eae as ON EOE Toone Doe een Len enn aoeer eee oer 17 Contents 3 Technician notes In this section Wheretogo foraddiional help acca etncuneiiedia tascam 4 A WARNING Only authorized technicians trained by HP should attempt to repair this equipment All troubleshooting and repair procedures are detailed to allow only subassembly module level repair Because of the complexity of the individual boards and subassemblies no one should attempt to make repairs at the component level or to make modifications to any printed wiring board Improper repairs can create a safety hazard WARNING To reduce the risk of electric shock personal injury and damage to the equipment e Do not attempt to service any parts of the equipment other than those specified in the following procedure Any other activities may require that you shut down the server and remove the power cord e Installation and maintenance of this product must be performed by individuals who are knowledgeable about the procedures precautions and hazards associated with the product WARNING To r
6. cacaotrangandetaruncansssaggcedine stanassadyeeus bn eatankaoe i sotndasheontusnntepiatisscoanyieenatatesossaay 8 Installing an adapter in a server sisasceve cuss qeestang scans coen daegutad dees conaqqes ttendsoams Cataqeatd ad saetataneneetatas saaaeanedeaeea seca curd 9 Installing a low profile bracket ceizeisssasctawaeseiatvaschcsasupeleuarntesesnanlbnepest tasetunnSedesiuiseatinann quota dass lnatisneniaolys 9 Connecting the network clio aa ceraepragaanes sapcein camara ionssecvacinn twenannarshenatadignyonenrsttananiiesipnetnieaneeneeneemenaanvet 10 TE Ee E Seen Oe Eee eet ae ee A E mea a eer te eee eee ae re een eee 11 HP NC373F PCI Express Multifunction Gigabit Server Adapter specifications ccccccscceeeereeeeteeeeteteetreeentaeees 1 Peet Comp ne ees eee 12 Regulatory compliance identification numbers ccceccceesseeeeseeceneceeeseeeeeeeceneeeeseseeceaeeesnueeecnseeenaeeeeteeesnaeees 12 European Union regulatory notice s csiscacthssarasaviasravindsaranandsnscacsidsacensbl antekeassedbnsalncdeaisidosraaadenaiahaieat 12 Korean class B notice seeessiss seee eees sets sts stet tettest tast tserte ASE EStEESNEESSEEASEEESEEESEEESNEEASE EESE EESEEES ESEE ES EEES En aenema 13 eME c E TE A A E ETS 13 laser COMINGS canir E E S rE E aa 13 Disposal of waste equipment by users in private households in the European Union ccceceseceesteeeeseeeneeees 14 Beppe het Nita a eh connec E AE ansaid 1S Preventing electrostatic discharge
7. cess RDMA when those features become available For details about each of these advanced features and for other information regarding the latest functionality features and operating system support for this server adapter see the HP website hitp h18004 www 1 hp com products servers networking index nic html Introduction 6 LED indicators The NC373F adapter has a single fiber LC port and LED indicator for link activity Fiber LC Port Link Activity LED LNK ACT Off No link to the adapter is established The adapter is not receiving power or the cable connection is faulty No link to the adapter is established Link to the adapter is established The adapter is receiving power and the cable connection is good Flashing The adapter is sending or receiving network data at 1000 Mb s Introduction 7 Installing an adapter In this section Joe ec Le eee ae ane E S Rapes Pte E er ee ver ee ered nee tery eran er ener tree etre nee nen A E er err eT 8 reverie Sciatic Tec athe det ec eciicscreeur rieaeastinsusnncstancn dinner 8 Pe NN ah RI TN eee A ude tiduenva neue a 9 Hanmer Nancy g law pratile EN sna inasiceia sanssicnsocinniernnemianbainnnssaaastounbsbencietntboienbatexiesenbnernadesuneand aae 9 Connecting the network cabl scsis drernen ean cancun N oren aA ARA ERAN EAN A A EEN ERAS ERA EEA TEENAA 10 Installation overview This chapter describes installation precautions how to install the
8. educe the risk of electric shock or damage to the equipment e Do not disable the power cord grounding plug The grounding plug is an important safety feature e Plug the power cord into a grounded earthed electrical outlet that is easily accessible at all times e Unplug the power cord from the power supply to disconnect power to the equipment CAUTION To properly ventilate the system you must provide at least 7 6 cm 3 0 in of clearance at the front and back of the server CAUTION The server is designed to be electrically grounded earthed To ensure proper operation plug the AC power cord into a properly grounded AC outlet only NOTE Any indications of component replacement or printed wiring board modifications may void any warranty Where to go for additional help 1 Go to the HP website http www hp com 2 Click Software amp Driver Downloads from the left menu bar Technician notes 4 3 Type the product name in the For product box and press Enter For example type NC370T 4 Download the drivers firmware or documentation as needed HP contact information For the name of the nearest HP authorized reseller e In the United States see the HP US service locator webpage hitp www hp com service locator e In other locations see the Contact HP worldwide in English webpage http welcome hp com country us en wweontact html For HP technical support e In the United States for contact o
9. ing of your waste equipment at the time of disposal will a help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product Regulatory compliance notices 14 Electrostatic discharge In this section Preventing elecirostotie discharge a sciciccancheniciwr ctntamnensmennuseuaienniceeiah e e a i Grounding methods to prevent electrostatic discharge ccccesceceessecseeeeeeeeeceeaeeceseeceeeeeensaeeeeeeeeseeeeesees 15 Preventing electrostatic discharge To prevent damaging the system be aware of the precautions you need to follow when setting up the system or handling parts A discharge of static electricity from a finger or other conductor may damage system boards or other static sensitive devices This type of damage may reduce the life expectancy of the device To prevent electrostatic damage e Avoid hand contact by transporting and storing products in static safe containers e Keep electrostatic sensitive parts in their containers until they arrive at static free workstations e Place parts on a grounded surface before removing them from their containers e Avoid touching pins leads or circuitry e Always be properly grounded when touching a static sensitive
10. it Server Adapter specifications 6 5 x 2 5 in 16 5 x 6 5 cm without bracket Fiber LC up to 1 804 ft 550m with multimode fiber 50um 125m Interrupts Supported Automatically configured Temperature Range Operating 0 C to 55 C 32 F to 131 F _ Storage 40 to 85 C 40 F to 185 F Relative Humidity non condensing Operating 10 to 90 a ore e Safety Compliance CSA Mark US and Canada CE Mark EN 60590 Specifications 11 Regulatory compliance notices In this section Regulatory compliance identification MuMbers oiciccscscccnsessaciissnnceianassonancssnnceanedsdnen iienaa ad aa 12 Eurspean Union Ceuta WH Se opnaaede anaE ADE aE ARS 12 arean okee E Ma eaer N 13 EEU IE TS 2 AT E E TAE EEE E E a gum EAE A ANE AE E A A E E A ences ak OE E 13 Les eaten Ree ela haces ara Po A hia as ce acs etc ended eee 13 Disposal of waste equipment by users in private households in the European Union ceccesseeeereeeseeenteeeneees 14 Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification this product has been assigned a unique regulatory model number The regulatory model number can be found on the product nameplate label along with all required approval markings and information When requesting compliance information for this product always refer to this regulatory model number The regulatory model number is not the marketing name or model numbe
11. mory Access RSS Receive Side Scaling TOE TCP IP Offload Engine UTP unshielded twisted pair Acronyms and abbreviations 16 Index B bracket low profile 9 C cables networking 10 cautions 4 E electrostatic discharge 8 15 F features 6 G grounding methods 15 installation overview 8 installing adapters 9 N NIC LEDs 7 R regulatory compliance notices 12 S specifications 11 Index 17
12. ou may need to replace the standard profile bracket with a low profile bracket See Installing a low profile bracket on page 9 4 Replace the access panel and plug in the power cord Installing a low profile bracket You may have to install a low profile bracket to complete the product installation The low profile bracket replaces the existing standard profile bracket shipped on the product To install a low profile bracket Installing an adapter 9 1 Using a correctly sized slotted screwdriver carefully remove the two board lock screws located at the top and bottom of the connector 2 Remove the standard profile bracket and place the low profile bracket over the connector Be careful not to damage the connector or bind the low profile bracket to the connector Connecting the network cable The HP NC373F PCI Express Multifunction Gigabit Server Adapter uses an LC fiber port This port supports multimode fiber with a maximum cable length dependent on the fiber type mode and cable size See Specifications on page 11 for the maximum cable length To insert the LC connector into the adapter port line up the slot on the fiber connector with the adapter and gently push until the retainers click into place Installing an adapter 10 Specifications In this section HP NC373F PCI Express Multifunction Gigabit Server Adapter specifications cssceeseeseeeeeteeeeeeeeeeentees 1 HP NC373F PCI Express Multifunction Gigab
13. ptions see the Contact HP United States webpage http welcome hp com country us en contact_us html To contact HP by phone o Call 1 800 HP INVENT 1 800 474 6836 This service is available 24 hours a day 7 days a week For continuous quality improvement calls may be recorded or monitored o If you have purchased a Care Pack service upgrade call 1 800 633 3600 For more information about Care Packs refer to the HP website http www hp com e In other locations see the Contact HP worldwide in English webpage http welcome hp com country us en wweontact html Technician notes 5 Introduction In this section E I ae te ase etapa iad dad eas E aki ae unsaid iad ATE E ica ita AEE E EE TEA ETE D EE A 6 ME ie Gt staciec orsxicinzinsnpetrsnnceiadusuanimeateancultleangiesnisnied a O z Overview The HP NC373F PCI Express Multifunction Gigabit Server Adapter is a high performance Ethernet adapter that delivers 1000 Mb s Ethernet over fiber cabling The network connection is made through an LC fiber port The LED indicator shows the activity and link status See LED indicators on page 7 for details The NC373F is a supported option for selected HP ProLiant servers and offers support for both standard and low profile slots In addition to features that have shipped with other server adapters the NC373F adapter will also support Receive Side Scaling TCP IP Offload Engine TOE Accelerated iSCSI and Remote Direct Memory Ac
14. r of the product European Union regulatory notice This product complies with the following EU Directives e Low Voltage Directive 2006 95 EC e EMC Directive 2004 108 EC e Machinery Directive 98 37 EEC Compliance with these directives implies conformity to applicable harmonized European standards European Norms which are listed on the EU Declaration of Conformity issued by Hewlett Packard for this product or product family This compliance is indicated by the following conformity marking placed on the product CE This marking is valid for non Telecom products and EU harmonized Telecom products e g Bluetooth CE xxxx O This marking is valid for EU non harmonized Telecom products Notified body number used only if applicable refer to the product label Hewlett Packard GmbH HQ TRE Herrenberger Strasse 140 71034 Boeblingen Germany Regulatory compliance notices Korean class B notice Ba 717 738 SBS 7I ol AIZIE 73822 AAMAS SB E IIEM u FHAA SE PEA Ql Pal ofo ni gt zo il ui jTi BSMI notice TARK EE PRR JE EEEN RHEA gt ORE Ie aA TE FEST ASS ERR SAR Laser compliance This product may be provided with an optical storage device that is CD or DVD drive and or fiber optic transceiver Each of these devices contains a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825 1 The product does not emit hazardous laser radiation
15. ting up the system or handling parts A discharge of static electricity from a finger or other conductor may damage system boards or other static sensitive devices This type of damage may reduce the life expectancy of the device To prevent electrostatic damage e Avoid hand contact by transporting and storing products in static safe containers e Keep electrostatic sensitive parts in their containers until they arrive at static free workstations Installing an adapter 8 e Place parts on a grounded surface before removing them from their containers e Avoid touching pins leads or circuitry e Always be properly grounded when touching a static sensitive component or assembly Installing an adapter in a server See the HP ProLiant server documentation for additional information on how to safely install a PCI Express card in the server Z CAUTION If the server is not PCI Hot Plug compliant power it down and unplug the power cord from the power outlet before removing the server access panel Failure to do so may damage the adapter or server 1 Power down the server 2 Remove the power cord and server access panel Then remove the cover bracket from a PCI Express slot Z WARNING To reduce the risk of personal injury from hot surfaces allow the drives and the internal system components to cool before touching them 3 Firmly seat the adapter in a PCI Express slot and secure the adapter bracket NOTE For 1U type servers y
Download Pdf Manuals
Related Search