HP L2105tm User's Manual
Contents
1. USER S MANUAL L2105tm 2209t LCD Touch Monitors Agency no HSTND 2791 Q Copyright 2009 HP All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of HP Product warranty or service will not be extended if 1 the product is repaired modified or altered unless such repair modification of alteration is authorized in writing by HP or 2 the serial number of the product is defaced or missing HP PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL HP ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS LOSS OF BUSINESS LOSS OF USE OR DATA INTERRUPTION OF BUSINESS AND THE LIKE EVEN IF HP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COM2. oem ors Appendix Connector pin assignment e 15 pin color display signal cable Description Co fwv o Legio grand n monitor round 32 Doeser Epe 15 DDG seral nme sequence PS ee 10 11 12 14 15 Pin No Ground Return for 5V TMDS Data 0 5 Shield TMDS Clock Shield PVINININ NIN ct BO PO O O 00 Ni amp O1 A
3. gt and in Figure 4 to adjust the brightness Contrast Press lt or gt and in Figure 4 to adjust the contrast IMAGE CONTROL Auto Adjustment Automatically selects the optimal settings for image parameters H POSITION Controls the picture s horizontal position V POSITION Controls the picture s vertical position CLOCK Sets up the internal clock Larger values make the displayed image appear wider smaller values make it appear compressed PHASE Adjusts the internal clock s time lag in order to optimize the screen image SHARPNESS Controls image sharpness COLOR This menu lets you select a preset color temperature 9300K 6500K or SRGB by pressing the OSD buttons lt or gt Changes to the color temperature take immediate effect on screen If you wish to set individual color values select the Custom Color option Then press the MENU button to select the red green and blue settings and set the desired value using the OSD buttons lt or gt The current settings are automatically saved when you return to the previous level or exit the OSD menu OSD CONTROL OSD CONTROL Fal 3 RGR O H OSD POSITION Controls the OSD menu s horizontal position Ca d Rp OAR E V OSD POSITION Controls the OSD menu s vertical position H OSD POSITION OSD TIMEOUT Determines how long in seconds the OSD V OSD POSITION menu waits before closing automatically after no action has been performed OSD TIMEO
4. the DVI connector on the rear of the PC Audio cable Connector one end of the audio cable to the audio in connector on the rear of the display and the other end of the cable to the audio out jack on the PC Connect one end of the USB cable to the USB connector on the display and the other end of the USB cable to the PC W Warning 1 Please verify the video card you are using and use an appropriate signal cable 2 Pay attention to the PIN assignments and connection directions Do not force to avoid bending the pins DVI Using the display Turning on the display Turn on the display before turning on the computer When the power is on the LED on the power button lights blue and the screen image will appear after about 10 seconds If the LED doesn t light blue or no image appears please verify if the display is properly connected Figure 4 Function controls 4 MENU OSD function OSD off Displays the OSD function menu menu OSD on Confirm the OSD function option OSD off Press this button directly to serve as the ol Left decrease shortcut for input OSD on Press this button to select decrease the adjustment button adjustment button OSD on Exit the OSD function menu Power ON OFF 5 POWER Power Switch Blue LED Power ON mode Orange LED Power saving mode Installing the Touch Driver for Windows XP only Insert the CD ROM into the Computer CD ROM drive The CD menu is displayed or open Windows Ex
5. MITMENT BY HP HP ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe First Edition October 2009 Document Part Number 582769 001 Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the
6. UT OTHER LANGUAGE OSD menu language selection ENGLISH DEUTSCH FRANCAIS ESPANOL ITALIANO POLSKI LANGUAGE NEDERLANDS PYCCKO _ INPUT Selects Analog D sub or Digital DVI D input INFORMATION SPEAKER VOLUME Adjusts the monitor loudspeaker output volume INFORMATION There is an optional OSD window on off that displays the newly adjusted screen resolution settings Note Do not adjust the screen setting when animation is displayed make sure to adjust the setting in full screen mode Troubleshooting Problems Possible solutions Power LED doesn t light up e Check if the power switch is in the ON position e Make sure the power cord is properly connected No screen image Check if the power switch is in the ON position Make sure the power cord is properly connected Make sure the signal cable is securely connected When the display is in use it will automatically turn off to enter the power saving mode Please press any key to see if the image resumes Abnormal colors are present e Please refer to the Color Temperature section to adjust the RGB color or select a color temperature The image bounces or a wave e Remove any electrical device that may be causing electrical pattern is present interference e Check the signal cable and make sure the pins are not bent The screen image is not e Press the Auto button to automatically optimize the display centered or the size is incorrect status e Refer to the Image Control s
7. ection Note Never disassemble or repair the product yourself If your problem cannot be solved according to the troubleshooting guidelines please contact your local dealer Production Specifications LCD panel size 54 61 cm 21 5in DCR Viewing angle Hesponse time Brightness Input signal Display color Frequency Optimum graphic resolution Max Pixel clock Tilt Audio output Power supply Power consumption Size Weight Environmental conditions 3000 1 typical Horizontal 170 vertical 160 typical 5 ms typical 265 cd m typical Analog signal D sub digital signal DVI 16 7 M colors 24 83 kHz Horizontal 50 76 Hz Vertical 1920 x 1080 60Hz 180 MHZ O ON 1WX2 AC 100 240V 50 60Hz Display mode Max 48W LED color Blue Sleeping mode Less than 1W LED color Orange Width 513 mm Height 393 mm Depth 228 mm Width 20 2 in Height 15 5 in Depth 9 in 6 4 kg 14 1 lb net Operating temperature humidity 5 35C relative humidity 10 85 Storage temperature humidity 5 35 C relative humidity 10 85 Preset Modes Horz Vert Preset Pixel Freq ied Freq Mia denis K Source kHz Y Hz y 25 175 eum se ae 2 orm 5 rer gt omm von Peso so sr ome ves a rena oases sos emm mn s oes o s eo remo vesn Le sesso oe s reso ovr aoma a ene 76 eo ommo vesn e reos o eo
8. equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio or television technician for help Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett Packard Company may void the user s authority to operate the equipment Cables Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations Declaration of Conformity for Products Marked with the FCC Logo United States Only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation For questions regarding the product contact Hewlett Packard Company P O Box 692000 Mail Stop 530113 Houston Texas 77269 2000 Or call 1 800 HP INVENT 1 800 474 6836 For questions regarding this FCC declaration contact Hewlett Packard Company P O Box 692000 Mail Stop 510101 Houston Texas 77269 2000 Or call 281 514 3333 To identify this product refer to the Part Series or Model number found on the product Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causin
9. g EquipmentRegulations Avis Canadien Cet appareil num rique de la classe B respecte toutes les exigences du Reglement sur le mat rielbrouilleur du Canada mig cerit Notice DREIZ JIAZBRRHRE CT COREIA Ries CRAY SCLEAMELTHET HN INR no 2vT TLE Vay AEROLINEAS HOF C0 5s 3 Mis CES TELL RUS LT Fat VCCI B Korean Notice 0 AWE DERBEZ HAHIABSES FILM F z ISOM ASE AS SACS o SS AIM Al Ze 4 SSUC BS A21 ORE SEEMS Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching ALS This feature allows the monitor to operate on input voltages between 100 120V or 200 240V The power cord set flexible cord or wall plug received with the monitor meets the requirements for use in the country where you purchased the equipment If you need to obtain a power cord for a different country you should purchase a power cord that is approved for use in that country The power cord must be rated for the product and for the voltage and current marked on the product s electrical ratings label The voltage and current rating of the cord should be greater than the voltage andcurrent rating marked on the product In addition the cross sectional area of the wire must be a minimum of 0 75 mm or 18 AWG and the length of the cord must be between 6 feet 1 8 m and 12 feet 3 6 m lf you have questions about the type of power cord to use contact an authorized HP service provider A power cord should be routed so that
10. it is not likely to be walked on or pinched by items placed uponit or against it Particular attention should be paid to the plug electrical outlet and the point where the cord exits from the product Japanese Power Cord Requirements For use in Japan use only the power cord received with this product A CAUTION Do not use the power cord received with this product on any other products Product Environmental Notices Materials Disposal This HP product contains mercury in the fluorescent lamp in the display LCD that might require special handling at end of life Disposal of this material can be regulated because of environmental considerations For disposal or recycling information contact the local authorities or the Electronic Industries Alliance EIA http www eiae org Disposal of Waste Equipment by Users in Private Household in the European Union b This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling or waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste e
11. king materials The procedures for re packaging the display are as follows 1 Unplug the power cord from the display make sure all attached peripherals are already turned off 2 Put the display into the carton in the original packaging manner 3449 LZ Important Before you start place a clean towel or cloth on a flat surface on which you can place the removed display panel without being damaged Adjusting the viewing angle You may adjust the display s viewing angle from 5 20 Figure 2 Note e When you agjust the viewing angle of the display avoid touching the LCD display with your fingers as this may damage or break the liquid crystal screen e When you agjust the angle of your display pay attention to your adjustment action as shown in the figure above Connection instructions A CAUTION Before installation please make sure to power off the display and the computer gt DI FERETE AS 7 he a a a pP 4 b a h A Y Figure 3 aee cord Connect one end of the power cord into the AC power connector on the rear of the display and the other end to an electrical wall outlet uni cable Connect the signal cable For analog operation use the VGA cable Connect the VGA signal cable to the VGA connector on the rear of the PC For digital operation use the DVI D cable Connect the DVI D signal cable to the DVI connector on the rear of the monitor and the other end to
12. na the aislada 5 PACKAGING proce CURES eii ias 5 Adj sting the VIEWING angle ic Oude evade du deme De 5 CONMECUOM IM SIMIC ONG iittala RI R 6 USING th CIS DIY mc 7 RST ail ale eo ame A ET ERE 7 FUNCION CONTO Sara di TNT 7 Installing the Touch Driver for Windows XP ONly oooccccoccccoccococcnconccconcoconacononcnnoncnnoncncnnnnnnnanoss 8 Gontrolror he OUCH dise NR T TU 10 OSD Selec 11 GSIBE QU ii aaa 11 TRFOUDIESNOOUING 5 2555 2 5 22032 02530303 0208225240202 5 22 035 02299 5e 0022 0 seudcnedecsdiqedeqedsendecavecdzee 13 Production SDCCITICALIONS emm 14 Preset p epe I m 15 A ae aaae aa a aE aaa asara aaia 16 Gonnector PIMas SIA MEN asar aii 16 Safety Instructions V Please keep the display away from any heat sources such as electric radiators or direct sunlight Place the display in a stable and well ventilated place The holes or openings on the display are designed for ventilation Do not cover or block the ventilation holes or openings with any objects Remove protective film on the screen before you use the display As the display surface is vulnerable to scratches avoid touching the surface with nail or pen point Shut off the power supply before cleaning Use a soft lint free cloth instead of a tissue to wipe the screen You may use a glass cleaner to clean the product as
13. pipes or direct sunlight Also keep the display away from excessive dust mechanical vibration or shock e Retain the original carton amp packaging materials They will be convenient for you if you need to transport your display again e For best protection pack the display in the original manner of package from the factory e Tomaintain a brand new appearance of the display clean with soft cloth regularly Please remove stubborn stains with soft cleaner rather than strong cleaners such as diluting agent benzene or corrosive cleaner as they may damage the display For the sake of safety remove the power plug prior to cleaning e The touch function may need about 7 seconds to resume if the USB cable is re plugged or the computer resumes from sleep mode suspend mode OSD selection Press the Menu button to activate the OSD function menu and continue pressing the Menu button to select an option from the 7 functions in the menu Select the function you want to adjust on the OSD function menu and then press MENU to make adjustment Please use lt or gt to adjust the screen to your desired status After finishing the setting press AUTO to exit the OSD screen OSD Menu C3 EE RGB OA R exi BRIGHTNESS d CONTRAST D lt gt ADJUST MENU ENTER AUTO EXIT IMAGE CONTROL AUTO ADJUSTMENT H POSITION V POSITION CLOCK PHASE SHARPNESS 9300K 6500K CUSTOM COLOR sRGB Brightness Contrast Brightness Press lt or
14. plorer and run the Touch_Driver_Setup exe from the CD Step 1 Click Install Touch Driver for Microsoft Windows XP from the CD menu NOTE The monitor ships only with Windows XP touch drivers Touch drivers are not required for systems running Microsoft Windows 7 and Vista operating systems Step 2 Click Install On Welcome installation window click Install ioi x1 Welcome to the Touch Driver Setup Wizard The Wizard will quide you through the installation af the touch driver It is recommended that you close all other applications before starting setup NOTE This software applies only to touch screen monitors and systems running Microsoft xP Click Install to continue Cancel After clicking Install the setup wizard shows the installation process ixi Installing ha Please wait while Touch Driver is being installed C Extract PSetup exe 10055 Output Folder MiProgram Files x86 TACTION Touch Created uninstaller MiPrograrn Files tee T4CTION Touch uninstall exe Qutpuk Folder MADOCUME ADMINI 1 LOCaLS 1 Tempyotm driver Extract otmfilter cat 100 Extract otmfilter inf 100 Output folder MDOCLIME 1 1ADIPTINIc UU LOCALSe 1 Templotro_driverlarmd Extract otmfilter sys 100 Output folder MilProgram Files 860 T4CTION TouchiDrvToo Extract Remover exe 100 Extract Remover ini 100 Output Folder MADOCUME 11ADIMIMI 1LOCaLS 1 Tempjotm driver Extract Poet
15. quipment for recycling please contact the local city office the household waste disposal service or the shop where you purchased the product Chemical Substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH Regulation EC No 1907 2006of the European Parliament and Council A chemical information report for this product can be found at http go reach Restriction of Hazardous Substances RoHS A Japanese regulatory requirement defined by specification JIS C 0950 2005 mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1 2006 To view the JIS C 0950 material declaration for this product visit http www hp com go isc0950 20084 HKIzdSlT o8 E XR E JSCO9502 4x ef ELi 2 je lk 2006477 A B UR Be e du ER ERA O REELS A EOSaT 2esxuctiiskbe UE 3x STU oXvELI S in 00 ED44 RT TOZELTIE www hp com go jisc0950 amp BELTS Monitor Placement Considerations For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces Table of Contents A aa 2 FECVCIING INTOFMAUON ii 3 System components and ACCESSOLIECS 02cccceeseeeeeseeenseeeeseeeeeseeseeseeeenseesonseeeonseesensessenness 4 Connection IAStUCIOAS cia 5 AStali
16. required However never spray the cleaner directly onto the display surface Do not attempt to repair this product yourself Improperly disassembly of the product may expose you to danger If your problem cannot be solved according to the Troubleshooting guidelines contact your regional HP authorized service provider http www hp com support Recycling Information HP encourages customers to recycle used electronic hardware HP original print cartridges and rechargeable batteries For more information about recycling programs go to http www hp com recycle System components and accessories LCD display Power cord Audio cable PRO SNe AS N M MT S a Y S m Signal cable VGA USB cable DVI cable ES A 9 e 7 s el Quick Start Guide User s manual CD Quick Start Guide Use the provided stylus as a touch pointing device However the stylus is not required for optical touch applications for example finger and other pointing instruments may be used If any component is missing please contact your local dealer for technical support or customer service Note Please keep the original carton and packing materials for future transportation or shipment of the display Connection instructions Installing the display Install Remove Place the display on the table Figure 1 Packaging procedures If you need to package the display again please keep the original carton and pac
17. up exe 100 Back ext gt Cancel Step 3 Click Finish The driver setup installation is complete Touch Driver Setup l a x Completing the Touch Driver Setup Wizard Touch Driver has been installed on your computer Click Finish Ea close Ehis wizard Back Cancel Step 4 Click Yes After clicking Finish the setup wizard will prompt you to reboot the computer E Successful installation Please restart your system For changes to take effect Do vau want to restart the system now Once the system is restarted the installation is complete Control of the Touch Function Note 1 Before using the touch function make sure the USB cable is connected the touch applications from the CD ROM are installed if you are running Windows XP and the Window s operating system is started 2 When the touch function is active make sure there is no foreign object in the areas encircled in the figure below Figure 5 Make sure there is no foreign object in the encircled areas The touch function may replace the mouse after you start the Windows operating system and introduce appropriate gesture judgement Gesture judgement and related Windows software applications are listed below indows XP Dag MMM Y Y Use your finger or the provided stylus for touch applications Note e Keep the display away from any heat sources such as electric radiators natural gas
Download Pdf Manuals
Related Search