Hotpoint LI2SNA User's Manual
Contents
1. 17a 18 Slide the bottom section of the chimney down until it completely covers the suction unit and slots into the housing provided on top of the hood Replace the grease filter s and where foreseen the grease collecting panels and check that the hood is operating correctly Description of the appliance Control panel Calibrating the control panel When the plug is inserted or after a blackout the system calibrates the keys during calibration the display point flashes Calibration lasts 15 The poin stops flashing at the end of calibration Off Stand by the On condition is obtained by 8 pressing Qor 3 seconds in this case keys II x and J l O are enabled the display pointand the blue led of the relative keys light up The Off condition is obtained by pressing O again for 3 seconds Os l Oz On Off lights press L to switch on the lights which turn amber Contem aa the symbols at the sides and turn blue the intensity of the light can be increased and diminished with these Once the luminosity has been set pressing L rapidly again memorises it the symbol turns blue and the light switches off Secondary light only for the models envisaged press o 2 for a long time to switch it on at least a second 8 ove press LA bnot motor press LA to switch the motor on It turns2. Remove the overhead light and remove the bulb to change Only use 40W lamps Make sure the bulbs are cold before touching them Halogen bulbs Use a small screwdriver or other tool suitable for prising Substitute the halogen bulb with another of equal value Close with the trigger fixing Changing the Neon only for the models envisaged Unscrew the screws and remove the overhead light on the upper part of the hood Change the damaged bulb with one with identical technical characteristics Caution General safety The hood has been designed and constructed in conformity with international safety regulations These warnings are provided for safety reasons and must be carefully read e This apparatus has been designed for use by adults e Children and invalids are not allowed to use this apparatus without supervision Check that children do not play with the apparatus e The premises must have sufficient ventilation when the hood is being used at the same time as other apparatuses that use gas and other fuels If the hood must be installed in a kitchen where there is a water heater or a gas heating system we recommend for safety reasons not using the suction version It is therefore necessary to equip the apparatus with an active carbon filter in this way allowing recycling use e For safe performance low pressure should not exceed 0 04 mbar in this way re suction of the expulsion gas will be avoided T
3. Adjust the horizontal position of the hood 7 Using a pencil mark the cooker hood permanent drill hole inside the suction group two drill holes are necessary for fastening 8 Remove the hood from the bracket 9 Drill at the point marked 8mm see operation 7 10 Insert2 wall plugs 11 Rest the chimney support bracket G against the wall touching the ceiling Use the support bracket as a drilling template the small slot formed on the support must coincide with the line drawn on the wall as above operation 1 and mark 2 holes with a pencil drill the holes d8mm insert 2 wall plugs 12 Fix the chimney support bracket to the wall using two 5x45mm screws 13 Hook the hood onto the bottom bracket 14 Fix the hood into its final position on the wall ABSOLUTELY ESSENTIAL 15 Connect a pipe pipe and pipe clamps not provided to be purchased separately for discharge of fumes to the connection ring located over the suction motor unit If the hood is to be used in ducting version the other end of the pipe must be connected to a device expelling the fumes to the outside If the hood is to be used in filter version then fix the deflector F to the chimney support bracket G and connect the other extremity of the pipe to the connection ring placed on the deflector F 16 Make the electrical connections 17 Apply the chimney stacks and fasten them at the top to the chimney support G 17b using 2 screws
4. amber a the symbols atthe again for at least a second to switch it off as well as i turn blue sides and E suction Pressing L amp S again switches the motor off and the lastspeed setis memorised to adjust the intensity of Sy Intensive timing by pressing this key the suction of the hood becomes intensive for a maximum time of 5 minutes At the end the hood returns to the speed u 7 0 previously set To exit from the function earlier press GEA or one of the following keys A or I amp I Fats filter signal this symbol red led lights up after 40 hours Reset the signal by pressing L J fora ong time at least 3 seconds until the beep confirms it e L amp I Carbon filter signal action This signal is shown only if it has been previously set l Proceed as follows press L with the hood in Off first L turns red after about 1 second L 8 also turns red If you want to eliminate the carbon filter signal previously set press L e with the hood in Off Reset the carbon filter signal after 160 hours by pressing L for a long time about 3 seconds until the beep Operation We advise switching the hood on at minimum power before beginning to cook to favour the optimal expu
5. appliance to the wall Surface mounting only Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed in case maintenance is ever required The minimum distance between the supporting surface or the cooking vessels on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65 cm from gas or mixed cookers f the instructions for installation for the gas hob specify a greater distance this must be adhered to 1 Using a pencil draw a line on the wall extending up to the ceiling to mark the centre This will facilitate installation 2 Rest the drilling template against the wall the vertical centre line printed on the drilling template must correspond to the centre line drawn on the wall and the bottom edge of the drilling template must correspond to the bottom edge of the hood bear in mind that when installation is complete the underside of the hood must be at least 50 cm above the cooker top in the case of electric cookers and at least 65 cm above the cooker top in the case of gas or mixed cookers 3 Rest the support bracket on the drilling template so that it coincides with the dotted rectangle mark the two outer holes and drill them remove the drilling template insert 2 wall plugs and fix the hood support bracket into place using two 5x45mm screws 4 Hang the hood on the bracket 5 Adjust the distance of the hood from the wall 6
6. K Hotpoint kitchen think Instructions for Installation and Use Electric Hood To the Installer Before installation fill in the product details on the back cover of this book The information can be found on the rating plate To the User You must read the instructions prior to installing and using the appliance and then retain them for future reference CE marking certifies that this appliance conforms to the following EEC directives Low Voltage Equipment 72 23 EEC Electromagnetic Compatibility 89 336 EEC Retention of this Instruction Book This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance If you sell or pass the appliance to someone else or move house and leave it behind make sure this Book is also provided so the new owner can become familiar with the appliance and safety warnings If the Book is lost or damaged a copy may be obtained from Merloni Elettrodomestici UK Ltd Morley Way Peterborough PE2 9JB Installation Itis important to conserve this booklet for consultation at any moment In the case of sale cession or move make sure it is together with the product Read the instructions carefully there is important information about installation use and safety Do not carry out electrical or mechanical variations on the productor on the discharge conduits Installation Electric connection T
7. available after sales service possible Extended Warranties UK 08709 088 088 www hotpointservice co uk Republic of Ireland 1850 502 200 Whether you have just one or anumber of Hotpoint appliances in your kitchen we offer two service cover plans to give you total peace of mind Repair Protection Plan FREE service repairs for a single Hotpoint appliance during the period of cover Kitchen Cover FREE service repairs for all your Hotpoint appliances less than 8 years old Genuine Parts and Accessories UK 08709 077 077 www hotpointservice co uk Republic of lreland 01 842 6836 Awide range of genuine parts and accessories are available from our hotline or through our website Genuine parts and accessories extended warranties and service repairs are all available on our web site at BB Hotpoint Key Contacts After Sales Service Over 1200 trained specialists directly employed by us ensure that you can have complete confidence in both the appliances and services we offer ESERVICECENTRE Repair Service and Information Desk UK 08709 066 066 Open 8 to 8 Mon Fri 8 to 6 Sat 10 to 4 Sun amp Bank Holidays www hotpointservice co uk Republic of Ireland 1850 302 200 Note Our operators will require the following information Model a Serial number i Extended Warranties UK 08709 088 088 Open 8 to 8 Mon Sun www hotpointservice co uk Republic of Ireland 1850 502 200 Genuine Parts and Access
8. ed frequently both internally and externally Use a cloth damped in neutral detergent liquids Avoid the use of products containing abrasives Attention failure to observe the cleaning regulations of the hood and the substitution and cleaning of the filters leads to the risk of fire We therefore recommend keeping to the suggested instructions Cleaning the grease filters The fats filter serves to capture the particles of fat in suspension that come from the cooking It must be cleaned once a month with non aggressive detergents manually or in a dishwasher at low temperature and short cycle If washed in a dishwasher it can become opaque over time but its filtering ability is not lessened in any way Dismantle it using the corresponding handles pushing them backward first and then pulling them down After having washed it dry it carefully and assemble it again in its seat reversing the procedure Clean the perimeter suction panel when envisaged with the same frequency as the anti fat filter Use a cloth and a not too concentrated liquid detergent Never use abrasive substances Mounting and changing the filter To remove the grease filter pull the spring release handle Carbon filter Remove the filter holder frame by turning the knobs g 90 that affix the chimney to the cooker hood Insert the pad i of activated carbon into the frame h and fit the whole back into its housing j Remove the plug Bulb s
9. he power tension must correspond with the tension shown on the characteristics label situated inside the hood If provided with a plug attach the hood toa socket conforming to the regulations in force and placed in an accessible zone If without a plug connected directly to the power supply use a regulation bipolar switch with a distance of the contacts on opening not less than 3mm accessible If necessary the situating of the supply cable must be carried out by the technical assistance service or a qualified person An authorized installer must carry out the electrical connection of the hood The company declines any responsibility whenever these regulations are not respected Preliminary information for installation of the hood Disconnect the hood during electrical connection by turning the home mains switch off Expansion wall plugs are provided to secure the hood to most types of walls ceilings However a qualified technician must verify suitability of the materials in accordance with the type of wall ceiling The wall ceiling must be strong enough to take the weight of the hood Do not tile grout or silicone this appliance to the wall Surface mounting only Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed in case maintenance is ever required Where foreseen remove the grease collecting panels Remove the grease filter s Do not tile grout or silicone this
10. his can be obtained ensuring entry of air into the room through openings that cannot be closed e The sucked air must not be conveyed in a conduit used for the discharge of fumes from apparatuses supplied with energy other than electricity e Itis severely forbidden to cook food on the flame under the hood e The use of naked flame damages the filters and can cause fires It must therefore be avoided in any case e Frying must be carried out under control to avoid the overheated oil catching fire e As far as the technical and safety measures to adopt for the discharge of fumes are concerned keep strictly to what is envisaged by the regulations of the competent authorities e For any problem regarding the expulsion of fumes keep to the instructions of the competent authority The company declines any responsibility in the case of damage or fire caused by apparatus resulting from failure to observe the above mentioned instructions Disposal e Disposing of the packaging material keep to the local regulations so that the packaging can be re used e European directive 2002 96 CE on electric and electronic apparatus waste provides that domestic appliance should not be disposed of in the normal flow of solid urban waste The disused apparatuses must be collected separately to make the rate of recovering and recycling of the materials they consist of and prevent potential damage to health and the environment The symbol of the barred baske
11. ironmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product E Hotpoint After Sales Service No company is better positioned to offer an after sales serviceon a Hotpoint appliance than us the manufacturer As part of our commitment to you all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months In addition to this you also have the advantage of free replacement parts for the first 5 years when fitted by a Hotpoint engineer When the 12 months parts and labour guarantee expires we offer the following after sales service options Repair Service and Information Help Desk UK 08709 066066 www hotpointservice co uk Republic of Ireland 1850 302 200 Note Our operators will require the Model number and the Serial number of your appliance Available 364 days a year with a fast effective and value for money service We have the largest white goods repair service in the UK with over 1000 of our own fully trained engineers All repairs include a parts and labour guarantee for 12 months from the date of the repair If you require any information or have any questions about your appliance our operators are on hand with help and advice All this ensures that you will receive the best
12. lsion of odours In addition we advise turning it off every time 10 15 minutes after finishing cooking We advise frying under the hood only under constant supervision It is forbidden to cook flamb under the hood because there is the risk of causing a fire The best performance of the apparatus is obtained with external expulsion we advise using the hood in this version if possible External exhausting version n this case the fumes are conveyed outside by means of a special pipe connected with the connection ring ocated on top of the hood Diameter of the exhausting pipe must be equal to that of the connection ring 150mm n the horizontal runs the exhausting pipe must be slightly slanted about 10 and directed upwards to vent the air easily from the room to the outside Attention If the hood is supplied with active charcoal ilter then it must be removed Filtering version One active charcoal filter is needed for this and can be obtained from your usual retailer The filter removes the grease and smells from the extracted air before sending it back into the room through the upper outlet grid Maintenance Itis always necessary to isolate the hood from the power supply during cleaning and maintenance Therefore remove the plug We recommend carrying our maintenance regularly about every 10 days to ensure efficacious and constant performance ofthe hood Cleaning the hood The hood should be clean
13. ories UK 08709 077 077 Open 8 30 to 5 30 Mon Fri amp 9 to 12 Sat www hotpointservice co uk Republic of Ireland 01 842 6836 Indesit Company Morley Way Peterborough PE2 9JB LI2SNA Ed 01 06
14. t is shown on all the products to remind users of the need for separate collection e Disused domestic appliances can be delivered to the public collecting service taken to suitable local authority areas or if envisaged by national laws on the matter resold to dealers at the same time as purchasing new equivalent types of product e All the main producers of domestic appliances are active in the creation and management of collecting systems of disused apparatuses l In case of anomalies apply to the authorized technical assistance service and require original spare parts The information and technical data are subject to change and the producer in line with technical progress maintains the right to make modifications that he considers necessary without prior notice This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol mu on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local env
Download Pdf Manuals
Related Search