Hoover Vacuum Systems User's Manual
Contents
1. How to replace Disconnect hose power cord from elec trical outlet and disconnect power noz zle from extension wands Turn nozzle over and unscrew the 4 recessed Phillips head screws Note Do not remove the 3 screws in the triangle formation as these hold the motor in place Note The headlight E on the PowerMAX nozzle remains ON as long as the hose power cord is plugged into an electrical outlet What to buy Use only a genuine HOOVER Belt No 40201045 when a belt replacement is nec essary When to replace The belt should be checked from time to time to be sure it is in good condition To check remove the nozzle cover see fol lowing section Replace the belt if it is stretched cut or broken Return nozzle to original position lift off nozzle cover If belt is not broken pull it off the motor pulley B Position nozzle cover on front lip of nozzle base Press cover into place Turn nozzle over and replace screws How to replace Disconnect hose power cord from elec trical outlet and disconnect power noz zle from extension wands 1 Remove nozzle cover agitator and belt as shown in Figs 4 2 to 4 5 2 Lift out old agitator and discard 3 Replace new agitator and belt as shown in Figs 4 4 to 4 7 Lift up end of agitator Remove old belt from agitator pulley C and replace with new belt Lettering on belt must be visible The agitator brush roll repla2. Furniture guard Headlight PowerMAX amp Wind Tunnel nozzles Belt ch e ck window PowerMAX nozzle only Operate cleaner only at vo I t age specified on data plate on bottom of cleaner This cleaner is intended for household use LN ss Al 2 Assembling Push the wand tool latch on the hand grip A to the unlock symbol Push the hand grip A down onto wand so that the button projection B fits into the slot Push the latch to the lock 0 symbol to secure wand Push wand down onto second wand or tool so that button projection fits into slot Turn latch ring to lock into place Reverse proce dure to remove wand or tool Attach corded hose to wall inlet valve After attaching wands and nozzle to hose press remote control switch on the hand grip to OFF Open wall inlet valve and push end of hose firmly into opening Push hose power cord plug G into an electrical outlet 4 For metal wands attach second wand or tool by fitting button projection D on one into spring latch C of first wand Attach nozzle in same manner To release press down on center of latch and remove tool nozzle or wand Push plug F of nozzle power cord com pletely into cord receptacle underneath hand grip NOTE Before attaching or removing nozzle power cord always disconnect h
3. ship This warranty applies when the prod uct is purchased in the United States including its territories and possessions or from a U S Military Exchange A product purchased elsewhere is cov ered by a limited warranty which covers the cost of parts only for the time peri ods given above For Canada see Canadian Warranty This warranty does not apply if the power unit is used in a commercial or rental application This warranty covers all labor and parts necessary to place the power unit in correct operating condition during the warranty period Warranty service can only be obtained by presenting the power unit to a Hoover Factory Service Center listed on the back of this warranty Proof of pur chase may be required This warranty does not cover pick up delivery or house calls however if youmail your power unit to a Hoover Factory Service Center for warranty ser vice transportation will be paid one way under this warranty This warranty does not cover installa tion damages installation materials or damage to the power unit caused by defective or improper installation of the Central Vacuum System While this warranty gives you specific legal rights you may also have other rights which vary from state to state If there are any questions concerning this warranty or the availability of war ranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple Street North
4. obstructions in the hose wands or nozzle connector and maintain the cleaning effec tiveness of your Central Vacuum System 1 To check for obstructions first press ON OFF Switch on hand grip to OFF to turn off Power Unit 2 Disconnect nozzle power cord and wands from hand grip 3 Turn ON Power Unit and check hose end for suction Remove any obstruction 4 Remove nozzle from wands and attach wands to hose Check for suction and remove any obstructions 5 Before attaching nozzle to wands check nozzle connector A 6 Push nozzle connector down to lowest position Look into nozzle connector and remove any obstructions Limited Warranty Domestic Use Applies in United States Only POWER UNIT FIVE YEARS ALL MODELS SUCTION MOTOR FIVE YEARS MODELS5671 SEVEN YEARS Model S5673 TEN YEARS Model 5573 amp Model 5675 ATTACHMENT SET FULL ONE YEAR WARRANTY PACKED WITH ATTACMENTS The power unit of your HOOVER Central Vacuum System is warranted in normal household use in accordance with the instructions provided with your power unit against original defects in materials and workmanship for a period of five years from date of purchase In addition the suction motor of the power unit of Model 85673 is warranted for an addition al 2 years and the suction motors of Model 5573 and Model 85675 are war ranted for an additional 5 years against original defects in materials and workman
5. Canton Ohio 44720 Phone 330 499 9499 e APPLIES IN CANADA ONLY WARRANTY HOOVER DOMESTIC FLOORCARE APPLIANCE THE EXCEPTIONAL WARRANTY WITHOUT EXCEPTION A full warranty on all parts and labour in accordance with the chart on the follow ing page Notwithstanding any other provision in this warranty or any applicable statutory provisions neither the Company nor the Purchaser shall be liable to the other for special or consequential damages or damages for loss of use arising directly or indirectly from any breach of this con tract fundamental or otherwise or from any tortious acts or omissions of their respective employees or agents In no event shall the liability of the Company exceed the unit price of any part or parts which are defective or are not delivered Subject to any other warranty packed with the product this express warranty is the only warranty applicable to your HOOVER DOMESTIC FLOORCARE APPLIANCE and is expressly in lieu of any warranty otherwise implied by law including but not limited to implied war ranties or merchantability or fitness for any particular purpose The remedies available under this express warranty shall be the only remedies available to the purchaser Hoover Canada neither assumes nor authorizes anyone to assume for it any other responsibility related to the sale of HOOVER DOMES TIC FLOORCARE APPLIANCES This warranty is void if repairs are per formed by unauthorized
6. J starting with one of the end tabs Then push the groomer onto the middle and remaining end tab 4 Replace brush roll cover and hood as shown in Figs 4 17 and 4 18 Agitator brushes and brush roll replacement When to replace brushes With CORDED hose disconnect hose p ower cord from electrical outlet With CORDLESS hose disconnect end of hose from electrified inlet va I v e Headlight replace ment The headlight located on top of the power nozzle operates when the clean er is turned on Use only HOOVER part no 27317 307 which is a fused bulb when replacing the headlight 5 If you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Agitator brush roll won t run Possible cause Possible solution Hose power cord nozzle power cord or cordless hose not firmly plugged in Plug firmly into receptacle Broken or worn belt Replace belt Floor surface set to BARE in wrong position Set floor surface to RUG posi tion Continued 3 9 Problem Nozzle won t pick up Possible cause Possible solution Low suction Check Power Unit filter Blockage in system Remove blockage Agitator brush roll not running See preceeding section Agitator brush roll brushes worn Replace brushes Service To obtain approved HOOVER service and genuine HOOVER parts loca
7. KH VER Owner s Manual e English gt pp 1 11 Francais pp 12 17 Central Vacuum Systems Accessories Review this manual before operating cleaner www hoover com Index Assembling eese 4 How to Use Cleaner icones Cleaning tools Power nozzles If you have a problem Clearing blockages Service reoeer Important Safeguards Maintenance Lubrication 9 Standard and PowerMAX power nozzles Replacing agitator brush roll 7 Replacing belt 6 7 Replacing headlight 8 WindTunnel power nozzle Replacing agitator brush roll 9 Replacing belt Replacing headlight Unpacking Nozzle descriptions 1994 The Hoover Company www hoover com G Fill in and retain The HOOVER Central Vacuum System Accessories include a hose nozzle and tools For your record s please enter model and serial nu m b e rs in the spaces prov i d e d below and retain in a safe place Power Nozzle Pa rt No Serial No See bottom of power nozzle Accessory kit Model No see pack age panel Attach your sales receipt to this ow ner s manual Verification of purchase date may be required Important Safeguards When using an electrical
8. appliance basic precautions should alw ays be followed includingthefollowing BEAD ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Wa mi ng E To reduce the risk of fire electric shock or injury Do not use powered nozzle outdoors e Close supervision is necessary when any appliance is used by or near children Do not allow cleaning system to be used as a toy or to run unattended at any time Donotallow any objects to be put into wall inlets Keephairlooseclothin g fingers feet and all parts of body aw ay from openings rotating agitator and any other moving part s Do not operate nozzle in bare feet or when wearing open toe shoes or sandals Units with cordless hose use only with Hoover valve type W V The hose contains electrical wires Do not use if damage d c u t or punctured Avoid picking up sharp objects Do not pick up anything that is burning or smoking s u ch as cigarettes m at ches or hot ashes Do not use to pick up flammable or combu sti ble liquids such as gasoline or use in areas where they may be present Use extra care when cleaning stairs Do not put any object into openings Do not use with any openings bl o ck e d keep free of dust lint h a i rand anything that may reduce air flow Do not pull or carry by cord use cord as a handle close a door on cord or pull c o rd around sharp edges or corners Do not run appliance over cord Keep cord aw ay from heated surfaces A Iw ays disconne
9. cement What to buy The agitator may be replaced with either a single or double row of brushes Single row of brushes Hoover part No 48414 051 Double row of brushes Hoover part No 4841 4 049 The headlight PowerMAX power nozzle only The headlight located under the nozzle cover Use only Hoover part No 27317 307 which is a fused bulb when replacing the headlight Stretch belt back and attach to motor pulley Hold opposite end of agitator in place Push belt end forward rotating end plate D until it slides into place Turn agitator making sure it rotates freely When to replace Disconnect hose power cord from elec trical outlet To check condition of brushes move edge of card across agitator opening while turn ing agitator To maintain cleaning effective ness replace brushes if they do not touch card How to to replace Disconnect hose power cord from elec trical outlet and disconnect power noz zle from extension wands 1 Remove the nozzle cover as shown in Figs 4 2 to 4 5 2 Push old bulb into socket and twist to remove Push new bulb into socket and twist into place 3 Replace nozzle cover WindTunnel power nozzle The belt The belt in your power nozzle drives the agitator It has been designed specifically for use in this nozzle and is important for effective operation What to buy Use only a genuine HOOVER Belt No 40201180 when a belt replacement is n
10. ct cord from electrical outlet before connecting or disconnecting hose or motorized nozzle Unplug cleaner when not in use Turn off all controls before unplugging Disconnect hose from wall inlet and cord from electrical outlet when not in use and b e fore servicing motorized nozzle Grasp the plug to disconnect from wall outlet to avoid damage to cord plug prongs orreceptacle N ever handle plug or appliance with wet hands Donotuse with damaged cord or plug If appliance is not working as it should has been dro p p e d d a m age d left outdoors or dropped into water take it to Hoover Factory Service Center or Auth or i zed Hoover Warranty Service Dealer Depot Use vacuum cleaner only for its intended use as described in this ow n e r s manual Use only attachments recommended by The Hoover Company o t h e rs may cause hazards Save these instructions o romnmmauo Corded Hose Models 5697 S5701 S5703 Cordedless Hose Model 5709 Power nozzle see descriptions below Crevicetool Dusting brush Wall floor brush Furniture nozzle Extension wands some models have two sets of extension wands metal wands which can remain attached to the power nozzle plastic wands which can be used with cleaning tools Hose Toolrack Nozzle Descriptions 1 2 Standardnozzle ModelS5697 PowerMAX nozzle Model 5701 WindTunnel nozzle Models 5711 S5713
11. ec essary When to replace The belt should be checked from time to time to be sure it is in good condition To check remove the hood see following section Replace the belt if it is stretched cut or broken How to replace With CORDED hose disconnect hose p ower cord from electrical outlet With CORDLESS hose disconnect end of hose from electrified inlet va v e Then disconnect power nozzle from extension wands To remove hood turn nozzle over and unscrew the 4 recessed Phillips head screws Note Do not remove the 3 screws in the triangle formation as these hold the motor in place Return nozzle to original position and lift off hood If belt is not broken but is stretched or Cut pull it off the motor pulley F Remove brush roll cover E by remov ing the 3 Phillips head screws Lift up end of agitator brush roll Remove old belt from agitator pulley G and replace with new belt Lettering on belt must be visible Lift off brush roll cover E Stretch belt back and attach to motor pulley Hold opposite end of agitator brush roll in place Push belt end forward rotating end plate H until it slides into place Turn agitator making sure it rotates freely Replace brush roll cover E over agitator brush roll Replace 3 short screws When brush roll brushes are worn the brush roll should be replaced To check condition of brushes move edge of a card across bottom pla
12. grip or wands as shown in assembly section Power nozzles Carpet or rug cleaning When using the nozzle for carpet and rug cleaning push the Floor Surface Switch D on hand grip toward RUG This setting provides the agitator action necessary to deep clean carpets The nozzle adjusts automatically to various carpet pile heights It is therefore necessary to always unplug the hose power cord from the electrical outlet when cleaning is fin ished On the PowerMAX nozzle the belt is visi ble through the belt check window A on top of the nozzle If the belt is broken the motor pulley will be visible through the win dow Hard surface floor cleaning The nozzle can be used for cleaning hard surface floors such as wood linoleum vinyl asphalt and rubber tile sealed cork concrete and terrazzo as well as carpet To set the power nozzle for hard surface floor cleaning push the Floor Surface Switch D toward BARE This setting provides no agitator action If you prefer you may use the wall floor brush to clean bare floors Familiarize yourself with these home main tenance tasks as proper use and care of your cleaner will ensure continued clean ing effectiveness Standard and PowerMAX power nozzles The belt The belt in your power nozzle drives the agitator It has been designed specifically for use in this cleaner and is important for effective operation
13. ose power cord CORDED hose from electrical outlet or disconnect hose from To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a quali fied electrician to install the proper outlet DO NOT CHANGE THE PLUG IN ANY WAY Unplug hose power cord when finished cleaning For plastic wands turn plastic latch ring on wand until outer slot lines up with inner slot electrified inlet valve CORDLESS hose Position nozzle power cord into clips on wands placing excess cord between noz zle and bottom clip Attach cordless hose to electrified wall inlet valve After attaching wands and nozzle to hose press remote control switch on the hand grip to OFF Open electrified wall inlet valve and push end of hose and mating pins into opening Hose is automatically energized to operate nozzle Unplug hose when finished cleaning Hand grip controls ON OFF Switch The ON OFF switch A for the Power Unit is located on the hand grip of the hose Brushed edge cleaning Brushed edge cleaning is provided on both sides of the nozzle to remove embed ded dirt in carpet near baseboard and fur niture Guide side of nozzle parallel to edge of carpet or furniture as shown Floor Surface Switch The floor
14. persons or if other than genuine Hoover replacement parts or accessories are used For commercial or rental use the wa r ranty is limited to three 3 months from date of purchase This wa r ranty is not applicable to H o over products sold in those Provinces which have consumer legislation which specifies mandatory wa r ranty provisions limiting and defining wa r ranty prov i sio n s HOOVER CANADA BURLINGTON ONTARIO L7R 4A8 1 800 263 6376 THE EXCEPTIONAL WARRANTY WITHOUT EXCEPTION HOOVER CENTRAL VACUUM PRODUCTS CENTRALVACUUM CLEANING ATTACHMENT SETS Full one year warranty covers everything including belts brushes and bulbs MODELS5671 S5672 CENTRALVACUUM POWER UNIT A full five year warranty on all parts and labour MODELSS5673 S5674 CENTRALVACUUM POWER UNIT A full five year warranty on all parts and labour PLUS AN EXTENDED WARRANTY FOR TWOYEARS ON THE MOTOR MODELS5675 and 5573 CENTRALVACUUM POWER UNIT A full five year warranty on all parts and labour PLUS AN EXTENDED WARRANTY FOR FIVE YEARS ON THE MOTOR Normal domestic use only Hoover Warranties are honoured at authorized warranty depots across Canada For in warranty or regular service contact a Hoover authorized service depot nearest you These dealers are listed in the yellow pages of your telephone directory under the heading of Vacuum Cleaners Household AUTHORIZED WARRANTY SERVICE DEALERS are listed in the directo
15. ry as in the following example HOOVER APPLIANCES AUTHORIZED WARRANTY SERVICE CENTER SMITH VACUUM CLEANER SALES amp SERVICE 123 ANY STREET 123 4567 IF FURTHER ASSISTANCE IS NEEDED IN CANADA CONTACT HOOVER CANADA 4151 NORTH SERVICE ROAD BURLINGTON ONTARIO L7R 4A8 1 800 263 6376 THE HOOVER COMPANY NORTH CANTON OHIO 44720 HOOVER CANADA A DIVISION OF MAYTAG LIMITED BURLINGTON ONTARIO L7R 4A8 11
16. surface switch B on the hand grip controls the agitator on the nozzles RUG turns agitator brush roll ON BARE turns agitator brush roll OFF Suction regulator The suction regulator C is located on one of the metal wands Open the suction regulator for less suction when cleaning lightweight fabrics or throw rugs Close the suction regulator as shown for maximum suction If power nozzle is difficult to push on some carpet open the suction regulator This will prevent damage to the belt Handle positions The handle has two positions when used with the power nozzle upright and operating To lower handle to operating position place your foot firmly on the power nozzle and pull handle back Cleaning tools The cleaning tools have many uses Select the tool best suited for the cleaning task from the descriptions below 1 Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers upholstered fumiture stairs and baseboards 2 Furniture nozzle may be used for upholstered furniture draperies tapestries mattresses clothing automobile interiors and carpeted stairs 3 Dusting brush may be used for carved fumiture table tops books lamps lighting fixtures venetian blinds baseboards shut ters and registers 4 Wall floor brush may be used for walls and wood vinyl brick slate and other hard surface floors Connect cleaning tools to hand
17. te the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by checking the Yellow Pages under Vacuum Cleaners Household OR checking the list of Factory Service Centers provided with this cleaner OR e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR checking the Service section of The Hoover Company online at www hoovercompany com Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the com plete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner Lubrication The motor is equipped with two bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not a dd lubricant to either motor bearing The agitator is equipped with two ball bearings that should be lubricated periodi cally by a Hoover Factory Service Center or an authorized Hoover Warranty Service Dealer Depot 10 Clearing blockages Remove larger items from carpet and floor surfaces before vacuuming to help prevent
18. te while turning brush roll To maintain cleaning effectiveness replace brush roll if brushes do not touch card How to replace Disconnect cleaner from electrical outlet and disconnect power nozzle from extension wands 1 Remove the hood as shown in Figs 4 10 and 4 11 2 Push old bulb into socket and twist to remove Push new bulb into socket and twist into place 3 Replace hood Edge groomer replacement When to replace The edge groomers located on both sides of the nozzle should be replaced when they no longer extend past the sur face of the bottom plate Position hood on top of nozzle base Turn nozzle over Replace 2 short screws at the back of nozzle and 2 long screws at the front What to buy When purchasing a new agitator brush roll ask for HOOVER part no48414 071 How to replace With CORDED hose disconnect hose p ower cord from electrical outlet With CORDLESS hose disconnect end of hose from electrified inlet va I v e 1 Remove hood duct cover belt and brush roll as shown in Figs 4 10 to 4 15 2 Discard old brush roll 3 Replace new brush roll and belt as shown in Figs 4 16 to 4 18 What to buy When purchasing edge groomers ask for Hoover part no 39511004 How to replace Disconnect cleaner from electrical outlet 1 Remove hood and b rush roll cover as shown in Figs 4 10 to 4 13 2 Pull off both old edge groomers I 3 Push each new groomer onto the 3 tabs
Download Pdf Manuals
Related Search