Hoover U57809RM User's Manual
Contents
1. shaft A Place other end of belt over large pulley B while rolling the pulley in direction shown Turn agitator brush rol making sure belt turns freely and is not pinched between agitator brush roll and agitator shield The V belt is designed to last for a long time and is not normally replaced However if the V belt is cracked gouged or broken it should be replaced Slide flat belt off large pulley as shown in Fig 4 14 To remove V belt slide back of belt over pulley A Then firmly pull on belt and snap it out To install new belt with lettering on outside of belt slide back of belt over pulley and pull front of belt toward groove B next to pulley Belt will pop into place V Belt What to Buy Use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for V belt HOOVER part No 40201 200 Reposition bottom plate and 6 Phillips head screws Tighten screws securely A Insert agitator brush roll through belt and position belt in groove A on agitator brush roll Agitator Brush Roll Disconnect cleaner from electrical outlet WARNING Agitator brush roll can start suddenly Unplug cleaner before turning it over Replacing Agitator Brush Roll When agitator brushes are worn the brush roll should be replaced Inspecting Agitator Br2. 2 With thumb and forefinger slide latch A located at the top of the housing to the right and pull down to remove K gray filter frame Remove black foam filter Rinse filter i frame cartridge and foam filter under cold water Allow both filter frame and filter to air dry for 24 hours before replacing filter into filter frame Reposition filter frame cartridge by inserting tabs into slots on back of housing Rotate filter cartridge frame up toward top of housing and snap closed D SS A 281 I 7189 Secondary Filter What to Buy When purchasing a new secondary filter cartridge ask for HOOVER part No 93002517 To purchase a new black foam filter ask for HOOVER part No 93002518 HEPA Final Filter How to Clean Disconnect cleaner from electrical outlet Do not use cleaner without dirt cup or filters in place INI With fingers in slots pull filter S 4 9 X 7 frame A straight out HEPA Final Filter What to Buy ql When purchasing a new HEPA filter L Dirt and debris can be cleaned from the filter cartridge by brushing with the cleaner s combination tool DO NOT RINSE OR WASH the HEPA filter cartridge Slide back into position on cleaner cartridge ask for HOOVER part No F j 93002360 Hy ff j SLA Headlight Disconnect cleaner from electrical outlet Removing Lens Installing Bulb Replacing Lens Press handle release pedal and place handle Pull old bulb straight Reposition le
3. 4 25 through 4 28 Powered Hand Tool Belt What to Buy When purchasing a new Powered Hand Tool Belt ask for HOOVER part No 38528 037 Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator brush roll is equipped with two ball bearings that should be lubricated periodically by a Hoover Sales and Service Center or an Authorized Hoover Warranty Service Dealer Thermal Protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and disconnect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service section Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer Depot by e checking the Yellow Pages under Vacuum Cl
4. Hoover Dealer Leading Retailers Hoover Sales amp Service Centers on line at www hoover com or by completing this order form Mail orders limited to U S residents only In Canada please call 1 800 263 6376 OR on line at hoover ca Please allow 3 4 weeks for delivery
5. blockage in the system Refer to the following steps to check for blockages continuing with each step until the blockage is found Fullness of Dirt Cup Check fullness of dirt cup empty if needed Check Hose Inlet Tube Check Airflow Path Plug cleaner in and turn ON Check for suction at end of hose A If there is suction turn cleaner OFF and unplug Check connection at Check Secondary Filter 5 3 G 2 47 LJ B E S a 2 C Remove and clean secondary filter Fig 4 8 p 10 Replace filter hose tube B remove any blockage Checking Under Bottom Plate remove blockage Turn cleaner OFF and unplug If blockage can be seen in tube A remove 5 screws using a Phillips screwdriver Pull tube from cleaner Reposition tube on back of cleaner replace 5 screws Blockage in Powered Hand Tool 5 6 og em A Disconnect powered hand tool from hose Remove bottom plate belt guard and turbine as described in Figs 4 24 4 25 and 4 31 Remove any blockage from turbine channel Replace belt turbine brush roll bel and bottom plate t guard Turn cleaner OFF and unplug Remove bottom plate Fig 4 13 and agitator brush roll Fig 4 20 Look into opening A in channels B and around liner C and remove any accumulated debris Replace agitator brush roll and bottom plate TTT Parts and Accessories
6. often Dirt Cup cont How to Empty Ah HE FA aii E Press dirt cup release button A and pivot cup out Place bottom of dirt cup into cleaner J body first Pivot cup into cleaner body Filters Cyclonic Filter Assembly How to Clean Holding dirt cup over trash receptacle press dirt cup door release button A to open dirt cup door B Close door and press dirt cup door release button to latch dirt cup door closed Press on dirt cup release button while firmly pressing on dirt cup LU Release button in order for it to return to proper position and lock the dirt cup into place K Disconnect cleaner from electrical outlet Do not use cleaner without dirt cup or filters in place Remove dirt cup as described in Fig 4 2 Twist filter assembly A counterclockwise Remove assembly from dirt cup Dirt and debris can be cleaned from the filter assembly by brushing with the cleaner s combination tool Place the filter assembly on the dirt cup aligning 3 tabs A on filter with 3 slots on dirt cup B and twist it clockwise to secure into position Press dirt cup door release button C to latch dirt cup door closed Replace dirt cup as described in Figs 4 4 amp 4 5 Filters cont Secondary Filter How to Clean Disconnect cleaner from electrical outlet Do not use cleaner without dirt cup or filters in place Remove dirt cup as described in Fig 4
7. AINTENANCE Stair Cleaning Use the hose and powered hand tool for stair cleaning Clean from bottom to top CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at bottom of stairs Turn cleaner OFF before disconnecting and connecting hose Remove hose end from dirt duct A Align end of Extra Reach hose with projections B over slots on dirt duct C Slide hose into slots and twist hose to lock it into place Align end of hose with projections D over slots E on Extra Reach hose Slide hose into slots and twist hose to lock it into place To detach hose reverse procedure Attach wands or tools to the other end of hose Note Hose must be connected to dirt duct and hose tube after removing Extra Reach hose for carpet or floor cleaning Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness Dirt Cup When to Empty the dirt cup Empty the dirt cup before the dirt reaches the fill line A Place the cleaner in the upright position before removing Disconnect cleaner from electrical outlet Do not use cleaner without dirt cup or filters in place CAUTION Very fine materials such as face powder or cornstarch may seal the filter and cause a reduction in performance When using the cleaner for this type of dust empty the cup and clean the filters
8. MAIL ORDER FORM Detach this section and mail to The Hoover Company 7005 Cochran Road s Glenwillow Ohio s 44139 Attn Sales amp Service Center hay kart an Price Pk Qty Total Description No HEPA Final Filter 93002360 1 8 99 Secondary filter cartridge 93002517 1 6 99 Foam filter secondary filter 93002518 2 3 99 Headlight 27313 107 1 2 49 Flat Belt 40201 271 2 3 99 V Belt 40201 200 2 4 99 TOTAL MERCHANDISE APPLICABLE STATE TAX SHIPPING amp HANLDING 7 50 TOTAL COST Parts and Accessories RETAIN THIS SECTION FOR YOUR RECORDS Item Description Part No Qty Pk Price Pk Qty Total HEPA Final Filter 93002360 1 8 99 Secondary filter cartridge 93002517 1 6 99 Foam filter secondary filter 93002518 2 3 99 Headlight 27313 107 1 2 49 Flat Belt 40201 271 2 3 99 V Belt 40201 200 2 4 99 TOTAL MERCHANDISE APPLICABLE STATE TAX SHIPPING amp HANLDING 7 50 TOTALCOST Order Date Received Date Ship tO please print clearly Name Street City State Zip Payment Method L Check or Money Order made payable to The Hoover Company m Visa J Mastercard 4 Discover Number Exp Date Name on Card Day Phone __ Signature req Replacement parts and accessory items may be purchased from your Authorized
9. Owner s Manual Operating and Servicing Instructions Windtunnel Cyclonic U57809RM REMANUFACTURED Review this manual before operating the cleaner www hoover com 2008 All rights reserved 17 01 58 058 00 H301 59881086 6 08 Thank you for choosing a HOOVER product Please enter the complete model and serial numbers in the spaces provided Model Hint Attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Contents Important Safeguards e ars Yd dd r dd aN ATR E Wale eee adhere a sega eters N NTT a 7 Cleaner Assembly seier enn ods Wa erie ARE wa aN ee BE R T N AA 4 Carton COntents a aZ 36 KSL 5 Za EEE Bis ae ahs eed Beale dA bene La dee ate ace 4 HOW TOUSGs asec E ae eee ates ee ies ey ete es Se et n ot ee Moa u eh 5 9 Cleaner DESCTIPLIONS 25 ra 9 a aed we bien aie R vp ae WER elec wie WS SA Sle ew Whee hue RN 5 Cleaning TOONS x sce cea STA aah oe Adee ae PAS EGE Dw CARE A ee 7 8 Maintenance L 2 S A te Se eGR EE bee Swe ee ok bas Sh hee os 8 13 Dirt eT Go A E A vieeatia ar Sous E erga TTT 8 9 FUL TTT 9 10 Headlight asien van dein dace gy dai ea de es Ye ewe ee wet 10 Bel bse ae ear eboney AS SONG to see snes BAT RUG ak AEST IEDR e BOSS Gh LAE NSS 11 Agitator Brush Rll son aerian Spices ane eth steele EE able ese E OS 12 Powered Hand TOOT recaia Sock aig des doce aT d tea oi ATA AA Wp erate ek eae betes 12 13 Agitat
10. ctrical wires 1 Carpet height setting is incorrect 1 Too much pressure being applied to tool 2 Blockage in turbine channel 3 Broken or worn belt 4 Low cleaner suction 1 Plug unit in firmly 2 Check fuse or breaker in home Replace fuse reset breaker 4 Unplug and allow cleaner to cool for 30 minutes This willl reset the thermal protector 1 Clear blockage Pg 16 2 Empty dirt cup Pg 9 3 Replace Agitator Brush Roll Pg 10 3 Replace belt Pg 12 5 Remove filter and clean Pg 9 10 6 Remove lower hose remove obstruction Pg 16 7 Set carpet height adjustment to appropriate setting for carpet being cleaned Pg 6 8 Step on pedal to turn Agitator Brush Roll on Pg 6 1 Empty dirt cup Pg 9 2 Review dirt cup removal EC replacement Pg 9 3 Review hose installation Pg 4 4 Review filter removal amp replacement Pg 9 10 1 Replace bulb Pg 10 2 Call 1 800 944 9200 for nearest authorized Hoover dealer 1 Set carpet height adjust lever to appropriate setting for carpet being cleaned Pg 6 1 Continue using tool applying light pressure 2 Remove blockage Pg 16 3 Replace belt Pg 13 4 Check items under Cleaner won t pick or low suction 1 Belt broken or stretched 1 Replace agitator brush roll belt Pg 12 Clearing Blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a
11. eaners Household OR e checking the Service section of Hoover on line at hoover com OR lt e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only Do not send your cleaner to Hoover in Glenwillow Ohio for service this will only result in delay lf further assistance is needed contact the Hoover Consumer Response Center Phone 1 330 499 9499 In Canada Carson Building 100 Carson St Etobicoke ON M8W3R9 1 800 263 6376 Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the back of the cleaner 5 TROUBLESHOOTING Cleaner won t run Cleaner won t pick up or low suction Dust escaping from cleaner Headlight not working Cleaner is difficult to push or won t move forward Powered Hand Tool Brush Roll won t turn Smoky burning smell detected 1 Power cord not firmly plugged into outlet 2 Blown fuse or tripped breaker 4 Thermal Protector activated 1 Blockage in air flow passages 2 Dirt cup full 3 Agitator Brush Roll worn 4 Broken or worn belt 5 Clogged filter 6 Nozzle dirt passage hose clogged 7 Carpet height setting is incorrect 8 Agitator Brush Roll is OFF 1 Dirt cup full 2 Dirt cup not installed correctly 3 Hose not installed correctly 4 Filter not installed completely 1 Bulb burnt out 2 Loose ele
12. ll or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces e Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by Hoover others may cause hazards e Hold plug when rewinding cord onto cord reel Do not allow plug to whip when rewinding WARNING e This product contains chemicals known to the State of California to cause cancer and reproductive toxicity Wash hands after handling Do not operate cleaner in bare feet or when wearing open toe shoes or sandals e Avoid picking up hard sharp objects with the cleaner They may damage the cleaner Save these instructions 1 CLEANER ASSEMBLY Carton contents Handle section Cleaner base and upper housing assembly Cleaning tools and wands Powered Hand Tool EA Remove all parts from carton and identify each item shown Make sure all parts are located before disposing of packing materials Using a Phillips screwdriver remove 2 screws from the top of the upper housing assembly Insert handle section A into upper housing assembly Push down firmly until you hear a click Fasten 2 screws on either side of handle base Position Tools Place smaller diameter end of wand A into bottom of rack Snap wand into clip at top Repeat with other wand Fit powered hand tool A i
13. n When you are finished cleaning with the tools reposition hose end into tube Attach Wand and Tools Attach tool or wand to the hose A Attach tool to wand B by pushing it firmly onto the wand Twist wand or tool slightly to tighten or loosen the connection Select Proper Tool A Dusting Brush maybe used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers Remove brush Fig 3 4 to clean upholstered furniture draperies mattresses clothing and carpeted stairs B Powered hand tool may be used for upholstered furniture draperies mattresses clothing automobile interiors and carpeted stairs C Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers upholstered furniture stairs and baseboards D Wands are used to give extra length to your hose Use them with any of the above tools How to Clean Tools To clean the hose and powered hand tool wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth DO NOT submerge powered hand tool in water Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Extra Reach Hose available at additional cost The Extra Reach hose provides easier cleaning of stairs and hard to reach places Follow the steps below for attaching and detaching the Extra Reach hose 4 M
14. ns and in low position out of socket Push secure with the screw new bulb straight into socket until locked in place Using a Phillips screwdriver remove the the screw as shown and lift off lens Headlight What to buy This cleaner uses a 13 volt T 3 114 wedge Excessive force is not required base bulb When purchasing a new lightbulb ask for Hoover part No 27313 107 Belts Disconnect cleaner from electrical outlet WARNING Agitator brush roll can start suddenly Unplug cleaner before turning it over The belts are located under the bottom plate of the cleaner and should be checked from time to time to be sure they are in good condition Replacing Flat Belt Replace belt if it is stretched cut or broken To check the flat belt refer to Fig 4 13 Removing Bottom Plate KREA Place handle in low position and turn cleaner over so bottom side is facing up Remove the 6 screws as shown with a Phillips screwdriver Lift off bottom plate Removing Belt C C Remove used belt A from large pulley B and discard Flat Belt What to Buy Use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for Flat belt HOOVER part No 40201 271 Inspecting V Belt Discard used belt Positioning Belt C With lettering on outside of belt slide new belt over motor A B
15. nto recessed area on front of cleaner Pivot toward handle to snap in place Crevice tool B fits into one of the extension wands Fit combination tool C into storage area on side of cleaner as shown 2 HOW TO USE Cleaner Description Soft Touch handle grip ON OFF switch Hose Dirt cup release button Dirt cup assembly Hose handle Cord reel window Headlight Nozzle control knob turn knob to correct setting for height of carpet being cleaned 10 Furniture guard helps prevent cleaner from marking furniture 11 Agitator brush roll shut off pedal 12 Agitator brush roll shut off indicator 13 Final filter access 14 Combination tool 15 Powered hand tool 16 Crevice tool 17 Hose tool holder 18 Wands This cleaner is intended for household use 19 Cord reel 20 Soft Touch wheels 21 Handle release pedal step JW K MM Operate cleaner only at voltage specified on data plate on back of cleaner Polarized plug on lever to lower handle to To reduce the risk of electric shock this appliance has a operating or low positions polarized plug one blade is wider than the other This plug 22 Cord rewind button press will fit in a polarized outlet only one way If the plug does button to rewind cord for not fit fully in the outlet reverse the plug If it still does not storage Hold plug until cord is fit contact a qualified electrician to install the proper outlet rewound Do not change
16. o ensure that it is in good condition If belt is cracked gouged or broken replace it see following section Insert brush roll through belt and position belt over gear teeth B on brush roll To replace bottom plate insert the four tabs on edge of bottom plate into slots on front of tool Poe s a S AVIAN eee J c a Nl Pivot bottom plate down and snap closed Belt Replacement With curved ends down slide end plates A of brush roll into slots B on tool Replace belt guard A making sure not to pinch brush bristles in guard Turn agitator to make sure it rotates freely Replace and tighten screws Agitator Brush Roll What to Buy When purchasing a new Powered Hand Tool Agitator Brush Roll ask for HOOVER part No 48414 088 The powered hand tool belt is designed to last a long time and is not normally replaced However if the belt is cracked gouged or broken it should be replaced Inspecting the Belt Replacing the Belt The belt can be seen through the top of the nozzle or by removing the bottom plate and belt guard Figs 4 23 to 4 24 Grasp turbine A and pull firmly to remove Remove belt from turbine pulley B Replace with new belt With flat sides of turbine retainers A pointing down slide retainers into grooves B in tool housing and 1 snap into place Replace brush roll belt guard and bottom plate as described in Figs
17. or Brush Roll xa RR Rea echt 0 BES O REE IS RORA TTS 12 13 Power Hand Tool Belt cc ccc cc ce cent e eee ne eA 13 VAI DTI CATION saes pear E aided dikes e Brett REEE E E RGN aude EAE bees 14 Thermal Protectors is ax cieve dae atin a Sia te Pd fae aaa va Bile eee ae ek ee 14 Authorized Servic vx hoes we eek Se a Ow POAT A Ee VAN RM RS 14 Troubleshooting lt s sa ek Rar 2 KE S R ba ceed Z RTE obs agen basil aa Walaa 15 Clearing Blockage siij0 Zc EaR N Z RE Sok heaved Sandia ite REN Socks Sus RE angers 16 Warranty ea a S E igo ayiong itera w stye E E madly Oeera alae wn ptbew curse aha 16 Parts amp accessories mail reorder form 2 eee eee eee 17 18 If you need assistance Visit our website at hoover com Click on the Customer Service link to find the service outlet nearest you OR Call 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR Call 1 330 499 9499 to speak with a representative in our Consumer Response Center Please do not return this product to the store Important Safety Instructions When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING To reduce the risk of fire electric shock or injury e Do not use outdoors or on wet surfaces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a t
18. oy or to run unattended at any time e Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present e Always turn off this appliance before connecting or disconnecting hose e Unplug cleaner before connecting the powered hand tool Do not use without dirt cup or filters in place Empty cup and clean filter frequently when picking up very fine materials such as powder e Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow e Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands e The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer Depot Do not pu
19. rformance the following carpet height settings are recommended e Lowest setting for all types of carpet Note If the cleaner is difficult to push turn knob to the next higher setting s Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning performance Agitator Brush Roll Shut Off The agitator brush roll shuts off automatically for tool use when the cleaner is in the upright position To manually shut off the agitator brush roll for cleaning hard floors step on the pedal A The indicator B will show red in the brush roll off window To turn the agitator brush roll on step on the pedal again The indicator will show red in the brush roll on window 3 CLEANING TOOLS Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright position The agitator brush roll will not rotate when the cleaner is in the upright position or the if the agitator brush roll shut off indicator is in the OFF position when the handle is lowered Removing Hose When using cleaning tools place cleaner handle in the upright position The agitator brush roll will not rotate when the cleaner is in the upright position Also turn cleaner OFF before disconnecting and connecting hose to hose tube A pith Pc LLLA Baen To use hose lift hose end B as show
20. the plug in any way ON OFF Switch Brush Roll Switch The cleaner is shipped with the agitator brush roll in the OFF position To turn the agitator brush roll ON step on the pedal A The indicator B will show red in the brush roll on window Plug cord into electrical outlet To turn cleaner ON push ON OFF switch once To turn cleaner OFF push switch again Cord Rewind Grasp the end of the plug and pull to release cord from cord reel After desired cord length is reached the cord will lock into position To return cord for storage hold plug and press on button A at top of cord reel To prevent cord from whipping hold plug until cord is rewound Carpet Height Adjustmen The cleaning of carpet and rugs takes place at the nozzle A lS NE When it is gt FOG necessary pote N to raise and l S lell lower the nozzle for various carpet pile heights turn the nozzle control knob B to the desired setting Handle Positions Transporting Cleaner The handle of your cleaner has three positions upright for storage and when using cleaning tools operating position for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward Settings For maximum cleaning pe
21. ush Roll To check condition of brushes move edge of a card across bottom plate while turning agitator brush roll To maintain cleaning effectiveness replace agitator brush roll if brushes do not touch card Insert agitator brush roll through belt and position belt in groove Agitator Brush Roll What to Buy When purchasing a new Agitator Brush Roll ask for HOOVER part No 93002361 Powered Hand Tool Replacing Agitator Brush Roll Removing Agitator Brush Roll Turn carpet height adjustment knob to lowest setting Turn cleaner over and remove bottom plate Fig 4 13 N Lift up agitator brush v roll and slide V belt A 7 off agitator brush roll Grasp agitator brush roll firmly and fit it into position by first sliding end opposite the belt into the rectangular slot A on side of cleaner Pull other side of agitator brush roll B into place Belt may fit loosely when properly installed Reposition flat belt and bottom plate Figs 4 15 to 4 16 When agitator brushes are worn the brush roll should be replaced How to Replace 4 23 mali Turn tool so bottom faces up Press the latches on either side of tool and remove bottom plate A Unscrew the two Phillips screws and remove belt guard A Powered Hand Tool cont Replacing Agitator Brush Roll How to Replace Remove agitator including end plates A and discard Inspect belt t
Download Pdf Manuals
Related Search