Honeywell NPB-MDM User's Manual
Contents
1. Honeywell NPB MDM Modem Card GENERAL CAUTION This modem may require testing and certification in some European and Asian countries prior to connecting to the Public Switched Telephone Network Refer to the particular country s telephone authorities for further information This document covers the mounting and wiring of the NPB MDM Modem Card in a Honeywell WEB 201 Controller For related WEB IO mounting and wiring details refer to the WEB 201 Controller Installation Instructions form no 95 7722 The Honeywell NPB MDM Modem Card uses a 56kbps auto dial auto answer modem with one RJ 11 connector for the phone line The NPB MDM Modem Card must be installed in Option Slot 1 only where it operates as COM1 This disables the RS 232 base serial port DB 9 connector on the WEB 201 Controller Only one NPB MDM Modem Card is supported in a WEB 201 Controller Refer to Fig 2 for location of option slots SAFETY INSTRUCTIONS NOTES REGARDING DEVICE DESCRIPTION These instructions include indications for use and mounting of the device In case of questions that cannot be answered with these instructions please consult the product supplier or manufacturer It is the responsibility of the equipment installer to ensure that all federal state and local codes are followed INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS Keep these Installation Instructions for industrial safety and the prevention of accidents Only qualifi2. e up with the standoffs on the base board If they do not the connector is not properly aligned a Press until the NPB MDM Modem Card is completely seated 6 Place the custom end plate that came with the NPB MDM Modem Card over its connector See Fig 3 7 Plug the battery cable into the battery connector on the WEB 201 Controller See Fig 3 INSERT NPB MDM INTO OPTION CARD SLOT CAREFULLY WITH PINS ALIGNED FULLY SEAT CARD WEB 201 BATTERY CONNECTOR PLACE NPB MDM CUSTOM END PLATE OVER END M23342 Fig 3 Top view NPB MDM end plate insertion 8 Set the battery and bracket assembly back over the option card slots with the mounting holes aligned with the standoffs 9 Place the four screws through the battery bracket end plate and into the standoffs on the WEB 201 Controller base board Hand tighten these screws HAND TIGHTEN THE FOUR SCREWS THROUGH BATTERY BRACKET END PLATES INTO STANDOFFS M23343 Fig 4 Battery bracket screw re fastening 10 Replace the WEB 201 Controller cover a If accessory modules were unplugged plug them back into the WEB 201 Controller as before and secure WIRING Connect a standard RJ 11 telephone cable to the connector on the NPB MDM Modem Card and the other end to the working PSTN dialup telephone receptacle LEDS A single LED is visible on the top of the NPB MDM Modem Card cover must be removed from the WEB 201 Controller This LED is shown
3. ed personnel shall do mounting and installation work with these devices see section titled Qualified Personnel The information in these instructions must be read and understood by every person using this device QUALIFIED PERSONNEL Qualified personnel in the sense of these instructions are persons who are well versed in the use and installation of such devices and whose professional qualifications meet the requirements of their work This includes for example Qualifications to connect the device according to applicable specifications and regulations and qualifications to put this device into operation to power it down or to activate it by respecting the internal directions Knowledge of safety rules Knowledge about application and use of the device within the equipment system BEFORE INSTALLATION Unpack the NPB MDM Modem Card 2 Check the equipment and report any damage to a Honeywell representative 3 Read all of these instructions and ensure they are understood Included in this Package Included in this package are the following items One NPB MDM Modem Card along with connector and end plate INSTALLATION INSTRUCTIONS form no 95 7730 Materials and Tools Required The following tools and supplies may be required for installation 2 Phillips screwdriver used to install the NPB MDM Modem Card 95 7730 NPB MDM MODEM CARD MOUNTING A WARNING Power to the WEB 201 Cont
4. on the top label of the NPB MDM refer to Fig 1 and operates as follows ACTIVE green When lit it indicates that the modem is connected to another modem a carrier is detected In this case the WEB 201 serial port LEDs on its lower base board should indicate transmit and receive activity NPB MDM MODEM CARD SERIAL SHELL NOTES If an NPB MDM Modem Card is installed and the WEB 201 Controller s Mode Jumper Refer to Fig 4 is put in Serial Shell position the WEB 201 base RS 232 port becomes active immediately following a reboot This allows an RS 232 connection to the Serial Shell for debugging purposes The NPB MDM Modem Card is inoperative during this period To re enable the modem the Mode Jumper must be put back in the NORMAL position and then reboot the WEB 201 Controller 3 95 7730 NPB MDM MODEM CARD Automation and Control Solutions Honeywell International Inc Honeywell Limited Honeywell Limit e 1985 Douglas Drive North 35 Dynamic Drive Golden Valley MN 55422 Scarborough Ontario M1V 4Z9 customer honeywell com U S Registered Trademark 2006 Honeywell International Inc Printed au te geeen paper containing at least 10 95 7730 J 04 06 post consumer paper fibers Honeywell
5. roller must be OFF when installing or removing option cards or damage will occur Also be very careful to plug any option card into its connector properly pins aligned The NPB MDM Modem Card is for Option Slot 1 only NOTE If another option card already exists in Slot 1 it must be moved to Option Slot 2 Refer to GENERAL and SERIAL SHELL NOTES sections M23340 Fig 1 NPB MDM Modem Card 1 Power down the WEB 201 Controller see WARNING in MOUNTING section 2 Remove the WEB 201 Controller cover a Press in the four tabs on both ends of the unit and lift the cover off NOTE If accessory modules are plugged into the WEB 201 Controller slide them away from the unit to get to the cover tabs 3 Remove the battery and bracket assembly by taking out the four screws holding it in place setting the screws aside for later a Unplug the battery from the connector on the WEB 201 Controller UNPLUG BATTERY HERE INCLUDES CABLE SCREWS 4 BATTERY ASSEMBLY AND BRACKET OPTION SLOT 2 BLANKING Sed PLATE OPTION SLOT 1 AREA NPB MDM MUST GO HERE M2341 Fig 2 Removal of screws and battery assembly 95 7730 4 Remove the Slot 1 blanking end plate a Retain the blanking end plate in case the NPB MDM Modem Card must be removed at a later date 5 Carefully insert the pins of the NPB MDM Modem Card into the socket of slot 1 option connectors The mounting holes on the option board should lin
Download Pdf Manuals
Related Search