Honeywell HD70 User's Manual
Contents
1. You must be fully aware of all the distinctive features and precautions related to this camera before installing it COMPOSITION Service Monitor Cable Ii F LE EKC Mounting Screw Guide Pattern Operation Manual INSTALLATION Stick the guide pattern on the wall or ceiling Yi siinsY Guide Pattern Drill four holes according to the guide pattern then insert anchors into the drilled holes Draw out power video wires Dome Base to the connecting places Fix the camera to a celling using four screws Mounting Screw Adjust desired focus and scene by turning and moving the 3 axis camera bracket by hand Put the dome cover over the Dome Cover ase 0 0 0 0 9 0 Fix the dome cover on the base by L Wrench L Wrench PRECAUTIONS r Do not install the camera in extreme temperature conditions Do use the camera under conditions where temperatures are within 20 C to 45 C Be especially careful with ventilation under high temperatures r Do not disassemble the camera There are no user serviceable parts inside it 2 Do not drop the camera or subject them to physical shocks It can cause malfunctions to occur r Note When this camera is installed near wireless communication devices that emits strong electromagnetic field irregularity such as noise on the monitor may appear Pan rotation Adjusting the horizontal angle CONNECTION a Connecti2. and ensure that the voltage and polarity are properly connected and being supplied correctly e Check if the lens is stained If dirty clean the lens with a soft clean cloth e Adjust the Back Focus of the lens again The camera does not work Check if you have connected the camera to a proper properly the surface of the camera Case is hot and a black line appears on the screen power source and If there is no problem with the power turn the unit off immediately and seek assistance from our Customer Service department e Check if the camera is pointed toward the sun or a fluorescent lamp e Adjust the angle or location of the camera if too much light is coming into the screen
3. e Power Consumption 5W e IR LED Specification 850nm 30 24EA The image on the screen is dim e The wire is polarized No Function Terminal olor Remark e Use 12VDC power source Power Input Red 12VDC Max 5W 400mA O CAMERA SET UP Fixed Lens amp IR LED Type The image does not appear on the screen The screen blinks a lot Honeywell HD70 Series e 1 3 Sony Super HAD CCD e High Resolution 550 TV Lines e 4mm Fixed Lens e Color Day Night with 24 LEDs e Auto White Balance e AGC BLC Flickerless On Off e Extra Video Output for Installer e 3 Axis Camera Construction e Vandal Resistant Dome Housing READ AND KEEP THIS OPERATION MANUAL Built in GEE camera bracket makes it much easier to rotate in any direction Function Selection Switch e FL Flickerless ON OFF e AGC Auto Gain Control ON OFF e BLC Back Light Compensation ON OFF Service Monitor Connecter Use service monitor connector to set camera angle amp focus when installing J501 3502 10 Epio AA WITCH VIDEO CAUTION When AGC is off D N does not work because the D N switching function is dependent on the AGC level TROUBLESHOOTING l If you have trouble operatig your camera refer to the following If the guidelines do not enable you to solve the problem contact an authorized technician e Check the power source for the monitor and camera
4. ng to Monitor and Power GND 12VDC Power Type Power 12VDC DIMENSIONS mm 101 0 m lt y an Z SPECIFICATIONS Dz al Model NTSC PAL Signal System Scanning System NTSC 525 Lines PAL 625 Lines 2 1 Interlace Scanning Frequency H 15 734kHz 15 625kHz Scanning Frequency V 59 94Hz 50Hz Image Sensor 1 3 SONY Super HAD CCD Total Effective Pixels No 410K 380K 470K 440K S N Ratio More than 50dB AGC Off Resolution 550 TV Lines Video Output Level 1 0 Vp p 75 Ohms composite Need Help Lens Fixed Lens f 4 0mm Focus Manual Sync System Internal Sensitivity O Lux IR LED Electronic Shutter 1 60 100 000 Sec 1 50 100 000 Sec ag White Balance Auto D AGC On Off BLC On Off with Slide Switch BS Flickerless On Off with Slide Switch e Input Output Connector Power Video IQ Power Consumption 12VDC 10V 15V 5W Max Dome Size 100mm o Weight Approx 844g a NAME AND FUNCTION Fixed Lens amp IR LED Type Tilt rotation Adjusting the vertical angle Horizontal rotation Adjusting the horizontal position of the screen IR LED 4mm Fixed Lens Video Output Red O _ Call 1 800 796 CCTV for sales service and customer support www honeywellvideo com Design and specifications are subject to change without notice IR LED 850nm 30 24EA O Sensor
Download Pdf Manuals
Related Search