Honeywell HB73 User's Manual
Contents
1. X This Weatherproof IR Camera is Dimensions mm designed for Ceiling or Wall Mounting 101 5 78 0 Regulatory Notice Simple to install Outdoor Surveillance Camera As surroundings darken it switches automatically from color to black and white mode to enhance sensitivity COMPOSITION Y Operation Manual L Wrench w ISS 2 Bracket Mounting Screws l SPECIFICATIONS Model Signal System NTSC PAL NTSC 525 Lines Sun Visor Fastener PAL 625 Lines Scanning System 2 1 Interlace Scanning Frequency H 15 734kHz 15 625kHz Scanning Frequency V 59 94Hz 50Hz Image Sensor 1 3 inch SONY Super HAD CCD Total Effective Pixels No 410K 470K S N Ratio 50dB Min AGC Off Resolution 550 TV Lines Video Output Level 1 0 Vp p 75 Ohms composite Lens Vari focal Lens F 1 2 f 3 8 9 5mm Focus Manual Q This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are Sync System Internal Sensitivity F1 2 0 3 Lux color 0 008 Lux DSS On 0 Lux IR LE2. 550 TV Lin e Auto White Balance AGC BLC Flickerless On Off 3 8 9 5 mm DC Vari focal Auto Iris Lens e Super Digital Noise Reduction SDNR E e Electronic Sensitivity up DSS On Off e Weatherproof Housing e IP65 OA EREL ED Rev 0 03 18 READ AND KEEP THIS OPERATION MANUAL PRECAUTIONS Q Do not install the camera in extreme temperature conditions Do use the camera under conditions where temperatures are within 10 C to 45 C Be especially careful with ventilation under high temperatures Q Do not install the camera under unstable lighting conditions Severe lighting change or flicker can cause the camera to work improperly Q Do not drop the camera or subject to physical shock It can cause malfunctions to occur Q Never point the camera into strong light or the sun It can damage CCD Q Note If there is a bright spot light in the scene smearing or blooming may occur Confirm that the power supply provides sufficient power before connecting the camera Bright Adjustment V R CONNECTION Connecting to Monitor and Power Yellow GND Power 12VDC l NAME AND FUNCTION oO 2 O O Used to adjust video output level of DC driven auto iris lens Video Video Output 12VDC Power Type e The wire is polarized e Use 12VDC power source Video Output 1 0 Vp p Res O C 2 Power Input Vari focal Lens Type P
3. D On Electronic Shutter 1 60 120 000 Sec 1 50 120 000 Sec White Balance Auto AGC BLC D amp N FL On Off Selectable designed to provide reasonable protection against harmful interference in a DSS On Off Max 32 times commercial environment D ZOOM On Off 2 x This ei Hats generates uses and ganiragiate radio frequency eneroy an DNR AUTO if not installed and use in accordance with the instructions may cause harmfu 5 interference to radio communications Operation of this oen ina Input AOutpUtEONNEcton Power Red Jack Video Yellow Jack residential area is likely to cause interference in which case the user will be Operrating Temperature 10 C 45 C required to correct the interference at his own expense Storage Temperature 20 C 65 C WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment CAUTION When this camera is installed near equipment like a wireless communication device that emits a strong electromagnetic field some irregularity such as noise on the monitor screen may happen Power Consumption 12VDC 10V 15V 0 3A 3 6W Max Dimensions WxHxD 75x78 x 150mm Weight Approx 800g Need Help Call 1 800 796 CCTV for sales service and customer support www honeywellvideo com Honeywell HB73 Series e 1 3 Sony Super HAD CCD e High Resolution
4. hoto Sensor IRLED Zoom Handle Used to adjust zoom magnification by turning Focus Handle 12VDC 10V 15V 0 3A Max 850nm 30 18EA CAMERA SET UP Service Monitor Connecter Function Selection Switch when installing EEEE 2993928 Seeess 322255 BSeee g NE al TROUBLESHOOTING Use service monitor connector to set camera angle amp focus BLC Back Light Compensation ON OFF AGC Auto Gain Control ON OFF D N Day amp Night ON OFF DSS Digital Slow Shutter ON OFF D Z Digital Zoom ON OFF FLK Flickerless ON OFF CAUTION When AGC is off D N does not work because the D N switching function is dependent on the AGC level If the guidelines do not enable you to solve the problem If you have trouble operating your camera refer to the following contact an authorized technician The image does not e Check the power source for the monitor and appear on the screen camera and ensure that the voltage and polarity are correct The image on the e Check if the lens is stained If dirty clean the lens with screen is dim a soft clean cloth e Adjust the Back Focus of the lens again The camera does not work e Check if you have connected the camera to a proper properly the surface of the camera case is hot and a black line appears on the screen power source and If there is no problem with the power turn the unit off im
5. mediately and seek assistance from our Customer Service department The screen blinks a lot e Check if the camera is pointed toward the sun or a fluorescent lamp When the brightness control of the monitor does not operate correctly you can optimize the picture picture by controlling the DC level of camera Used to provide for accurate focusing of object within the lens field of view Adjust the angle or location of the camera if too much light is coming into the screen
Download Pdf Manuals
Related Search