Honda 08B26-S9V-100 User's Manual
Contents
1. alcohol FRAME WIRE TIE VEHICLE HARNESS 20 PIN CONNECTOR CENTER PANEL OPENING BUS CABLE 14 PIN CONNECTOR 2002 American Honda Motor Co Inc All Rights Reserved 7 Using 1 2 of an EPT seal attach it to the frame at the location shown Measure 450 mm from the end of the BUS cable to the frame then bundle up the excess cable and secure it to the vehicle with three wire ties EPT SEAL WIRE Cut in half TIE s Bundle up ecure to the the excess vehicle harness BUS cable BUS CABLE 8 Attach 1 2 of an EPT seal to the edge of the frame in the area shown 1 2 EPT seal Clean with FRAME isopropyl alcohol FLOOR CARPET SLIT Cut here 9 Near the edge of the driver s seat raiser make a 50 mm slit in the floor carpet with a utility knife Route the BUS cable under the floor carpet and out the slit near the seat raiser 2002 American Honda Motor Co Inc All Rights Reserved 10 Install the right and left base brackets to the driver s seat raisers using two 6 x 12 mm flange bolts for each bracket Do not tighten the bolts yet 6x 12mm FLANGE BOLT RIGHT LEFT BASE BASE BRACKET BRACKET Installing the CD Changer 11 Carefully unpack the CD changer Remove the three shipping clips and discard the shipping cover Install an adhesive seal included with the CD changer kit over each of the three clips holes Save the shipping clips for your customer in t2. operating must not be included in the 5 minutes 2002 American Honda Motor Co Inc All Rights Reserved
3. ECTOR 7 of 8 20 Slide the audio unit into the center panel opening and reinstall the four screws Without Navigation Unit VEHICLE BUS CABLE CONNECTOR LEAD SCREWS reused AUDIO BRACKET With Navigation Unit ANTENNA LEAD BUS VEHICLE CABLE HARNESS VEHICLE HARNESS HEATER CONTROL FF SCREW AUDIO UNIT reused 8 of 8 All 23607 0205 21 Check that all wire harnesses are routed properly and all connectors are plugged in 22 Reinstall all removed parts 23 Place shipping clips in a plastic bag and put the bag in the glove box 24 Reconnect the negative cable to the battery 25 Enter the customer s radio anti theft code and reset the radio station presets NOTE Whenever the battery is disconnected the driver s window AUTO function is disabled 26 Start the engine Push down on the driver s window switch until the window is fully open 27 Pull up on the driver s window switch to close the window completely then hold the switch for two seconds 28 Testthe AUTO window function 29 Do the idle learn procedure Make sure all electrical items are turned off Start the engine Hold the engine speed at 3 000 rom with no load in Park or Neutral until the radiator fan comes on Let the engine idle for about 5 minutes with the throttle fully closed and with all electrical items off NOTE If the radiator fan comes on during this step the time when it is
4. ET FLANGE NUTS 4 LEFT CHANGER BRACKET RIGHT CUSHION TAPE CHANGER BRACKET CD CHANGER CUSHION TAPE LEFT CHANGER BRACKET Attach the cushion tape to the top of the left changer bracket align the cushion tape already attached Fold the cushion tape around the CD changer Insert the studs of the left and right base brackets into the holes in the left and right changer brackets then install the four flange nuts on the end of each stud Tighten the four flange nuts and four bracket bolts in step 10 on the bracket plates 2002 American Honda Motor Co Inc All Rights Reserved 18 Plug the BUS cable connector into the CD changer connector Bundle up any excess BUS cable and attach it to the CD changer bracket with the two wire clips installed in step 14 BUS CABLE WIRE CLIP T rf 19 At the dashboard area plug the BUS cable 14 pin connector the vehicle connectors and the antenna lead into the rear of the audio unit With Pocket AUDIO UNIT BUS CABLE 14 PIN CONNECTOR POCKET VEHICLE 20 PIN LEAD 2002 American Honda Motor Co Inc All Rights Reserved All 23607 0205 With Cassette Player AUDIO UNIT VEHICLE 20 PIN CONNECTOR SY A CASSETTE PLAYER LEAD BUS CABLE 14 PIN CONNECTOR With CD Cassette Tuner With Navigation Unit AUDIO UNIT BUS CABLE 14 PIN CONNECTOR VEHICLE 20 PIN CONNECTOR VEHICLE 16 PIN CONNECTOR VEHICLE 22 PIN CONN
5. he event the unit needs to be serviced SHIPPING CLIPS 3 F Y SHIPPING COVER Discard a k i ws ADHESIVE SEALS 3 All 23607 0205 5 of 8 12 Visually check the position of the spring adjusting pin on both sides of the CD changer If the spring adjusting pins are not in the horizontal H position move the pins to the horizontal H position by sliding them up with your fingers SPRING ADJUSTING PIN H HORIZONTAL LEFT LOCKING COVER Included with CD Changer kit RIGHT LOCKING COVER Included with CD Changer kit SPRING ADJUSTING PINS 13 Remove the adhesive backing from the L and R locking covers and attach them to the sides of the CD changer Align the diagonally opposite holes with the H and V positions 14 Install the right changer bracket to the CD changer using two 4 x 8 mm washer screws and the two wire clips Install the left changer bracket to the CD changer using two 4 x 8 mm washer 16 screws 17 4 x 8 mm WASHER SCREW LEFT CHANGER BRACKET f WIRE RIGHT CLIP CHANGER BRACKET FRONT 4 x 8 mm WASHER SCREW 6 of 8 All 23607 0205 15 Attach one cushion tape to the rear of the CD changer leaving half of the cushion tape extended past the CD changer Using scissors cut the cushion at the end of the CD changer Fold the ends down and around the end of the CD changer RIGHT BASE BRACKET LEFT BASE BRACK
6. nnect the negative cable from the battery 3 Remove the audio unit Without Navigation Unit e Using a flat tip screwdriver wrapped with a shop towel gently pry out on the audio panel to remove the five clips Unplug the connectors and remove the audio panel VEHICLE CONNECTOR AUDIO PANEL CLIPS 5 2 of 8 All 23607 0205 e Remove the four screws that fasten the audio brackets Pull the audio unit out toward you unplug the vehicle connector and antenna lead from the rear of the audio unit VEHICLE ANTENNA AUDIO CONNECTOR LEAD UNIT AUDIO BRACKET SCREWS Reuse AUDIO BRACKET With Navigation Unit e Remove the driver s and passenger s center console trim pieces three clips each Take care not to damage the clips PASSENGER S DRIVER S CENTER CENTER CONSOLE TRIM CONSOLE TRIM CLIPS 3 2002 American Honda Motor Co Inc All Rights Reserved e Remove the center panel four self tapping screws two clips and unplug the vehicle accessory power outlet CLIPS 2 CENTER SELF VEHICLE TAPPING CONNECTOR SCREW e Remove the four screws that fasten the audio brackets Pull the audio unit neater control unit out toward you unplug the vehicle connectors and antenna lead ANTENNA HEATER LEAD CONTROL UNIT AUDIO BRACKET _ Sy S KY j f P YS VEHICLE O CONNECTOR Q K Q AUDIO SCREW BRACKET AUDIO UNIT 2002 American Honda Motor Co Inc All Righ
7. ts Reserved 5 All 23607 0205 On the driver s side of the vehicle gently pull the center console lower cover out toward you to release the seven clips and remove the center console lower cover Take care not to damage the clips DRIVER S DRIVER S CENTER CONSOLE LOWER CLIPS 7 COVER Remove the driver s seat front cover by pulling it toward you Take care not to damage the clips DRIVER S DRIVER S SEAT FRONT COVER CLIPS 4 3 of 8 Routing the BUS cable 6 Route the BUS cable Without Navigation Unit e Route the BUS cable from the dashboard opening to the driver s floor Pull out the end of BUS cable 30 mm from the end of the vehicle 20 pin connector and secure the BUS cable to the vehicle harness and frame with three wire ties VEHICLE 20 PIN rA NNECTOR 14 WIRE TIE CO i CONNECTOR VEHICLE HARNESS ja if C FRAME C WIRE TIE 4of8 All 23607 0205 With Navigation Unit e Route the BUS cable from the dashboard opening to the driver s floor Pull out the end of BUS cable 30 mm from the end of the vehicle 20 pin connector and secure the BUS cable to the vehicle harness with wire ties e Cutthe EPT seal in half Attach 1 2 of the EPT seal on the edge of vehicle body to protect the BUS cable Before attaching the tape wipe the surface with isopropyl alcohol e Secure the BUS cable on the vehicle frame with two wire ties EPT SEAL Clean with isopropyl
8. www collegehillshonda com parts HONDA Accessory Application Publications No All 23607 INSTALLATION ene cop 2003 2004 PILOT ATTACHMENT Issue Date PARTS LIST CD Changer Attachment Kit sold separately 8 Wire ties P N 08B26 S9V 100 Right base bracket 4 Washer screws 4 x 8mm 2 Wire clips CD Changer sold separately P N 08A26 1B1 100 Right changer bracket p CD changer AZ Sw LE Left changer bracket Left base bracket Not used Adhesive seal sheet Locking covers 4 Flange bolts 6 x 12 mm Q CD magazine ih Owner s Manual lt P 2 Cushion tapes Gray Small wire tie Not used 2002 American Honda Motor Co Inc All Rights Reserved All 23607 0205 08B26 S9V 1000 91 1 of 8 4 Washer screws 4 x 6 mm 2 BUS Cable O 4 Flange nuts amp C 2 EPT seals Black TOOLS AND SUPPLIES REQUIRED Flat tip screwdriver Phillips screwdriver Shop towel Diagonal cutters 10 mm Combination wrenches Isopropyl alcohol Utility knife INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers 1 Make sure you have the anti theft code for the radio then write down the frequencies for the preset buttons 2 Disco
Download Pdf Manuals
Related Search