Hifionics Colossus User's Manual
Contents
1. 4 Troubleshooting And Diagnostics nennen 5 Features And Speciflcatlons 6 EUER 7 Check out our videos of new products events and technical tutorials at www youtube com maxxsonicsusainc The contents of this manual may not be reproduced or copied without the written consent of MAXXSONICS USA Inc GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors such as the system design execution of the installation and system setup Please remember that any system is only as good as its weakest link Please remember that higher power systems are not necessarily useful purely for high sound pressure levels but also to establish a headroom capability to reproduce musical peaks cleanly without distortion Lower power amplifiers will clip earlier than their more powerful cousins and cause loudspeaker failure when overdriven due to the harmonics generated by a clipped signal thus overheating voice coils Amplifiers should be mounted with the fins running horizontally for best convection cooling to minimize overheating2. wh lz BOOST BANDWIDTH FREQUENCY LOW PASS E 34 0 BASS REMOTE MX 3 BASS CONTROLLER CLIPPING CONTROL GREEN PRE CLIP YELLOW SOFT CLIP SUBWOOFER SUBWOOFER BY RED HARD CLIP Converts High Level OEM speaker wires to Ultra Clean RCA Low Level Outputs High Level Inputs Accepts all types of High level Inputs including floating ground and high voltages up to 30 volts Parametric Bass EQ Provides a wide array of subwoofer output signal Audio Signal Sense Hardwire Turn On Audio sense detects shaping controls to enhance bass response and sound quality including music signals from the OEM wires and activates the MX 1 As Bass Boost adjustable Bandwidth wide and narrow Low Pass and an option the module also offers a remote turn on wire Subsonic Filter P Parametric Bass EQ Features Bass Boost adjustable Band Accepts a wide range of incoming music signal levels while Width wide amp narrow Low Pass and Subsonic Filter accommodating all types of head units and signal processors and Clipping Indicators Visually indicates audio signals Pre Clip controlling the output level to the amp to maximize a signal strength up to Soft Clip and Hard Clip Ru E To Balanced Line Output Ultra clean DIN variable high voltage Clipping Indicators Visual clipping indicators provide indication of
3. Power Suppl MOSFET Audio Ouput CROSSOVER Variable Low Pass Filter 24dB Variable Subsonic Filter 24dB Phase Shift 0 180 degrees PARAMETRIC BASS EQ Frequenc Bandwidth Boost CONNECTOR TYPE Unbalanced Inputs RCA Balanced Inputs DIN Line Ouput RCA Speaker Terminals Molded 1003 Power Ground Molded 003 Remote Level Module FUSING HEAT SINK DIMENSIONS LENGTH X WIDTH X HEIGHT INCHES Note Features subjectto change with out notice HIFONICS COLOSSUS Maxxsonics Limited Warranty As the manufacturer of Maxxsonics MB Quart Autotek Crunch and Hifonics car audio products Maxxsonics USA Inc Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one 1 Year from date of purchase All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one 1 year from date of purchase Maxxsonics will repair or replace at it s option and free of charge during the warranty period any system component that proves defective in materials and workmanship under normal installation use and service provided that the product is returned to the authorized Maxxsonics dealer from where it was purchased A photo copy of the original receipt must accompany the product being returned Valid purchase receipts will contain the name and address of the authorized reseller Any damage to the product as a result of misuse
4. abuse accident incorrect wiring improper installation alteration of date code or bar code labels revolution natural disaster or any sneaky stuff because someone messed up repair or alteration out side of our factory or authorized service centers and any thing else you have done that you should not have done is not covered This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith This warranty is not to be construed as an insurance policy Warranty on installation labor removal re installation and freight charges are not the responsibility of Maxxsonics USA Inc Warranty products damaged as a result of insufficient or improper packing materials are not covered by this limited warranty and such damaged product will be returned as is at the expense of the owner MAXXSONICS Designed and Engineered in the USA www maxxsonics com MAXXSONICS OEM Integration Accessories MX 1 Premium High To Low Level Converter MX 3 Bass Controller Bass Remote MXR 3 GREEN PRE CLIP LAM cem VOLUME RED HARD CLIP BANDWIDTH FREQUENCY SUBSONIC SUBWOOFER PARAMETRIC BASS EQ zu CMS SM 248 0 2498 6 LEVEL M x 1 CLIPPING CONTROL 7 1 LINE LEVEL d sa QMERED CONVERTER RED HARD CLIP 1 1 1 4
5. do not have to try to get all of the amps pre amp features such as Low Pass Subsonic Filter Bass EQ and phase control matched identical by ear Link up to five amplifier pairs 10 amps on one Maxx Link and more with Y Adaptors Clipping Indicators Visual clipping indicators provide indication of damaging clipped signals to help protect the subwoofer s and amplifier Includes pre clip soft clip and full clip indications Bass Remote Included bas Remote features built in clipping indicators allows direct bass control from in dask or under dash Tone Generator Built in 65Hz test tone for gain matching Low Pass 24db Lop Passvaraiable from 35Hz to 250Hz Subsonic Filter 24dB Subsonic filter variable from 15Hz to 35Hz Parametric Bass Eq Variable Wide and Narrow Bandwidth control Line Driver Variable output from 1 volt to 9 volts Phase Shift variable from 1 to 180 degrees 2 channel pass through MAXXSONICS MBOUARTI HIFONIC 5 CRUNCH WWW MAXXSONICS COM 847 540 7700
6. or settings REMOTE The Colossus has a DIN cable remote level jacks labeled INPUT The Remote Module plugs into the INPUT jack and allows you to adjust the Level Control INPUT OUTPUT NER LEVEL PHASE BOOST BANDWIDTH FREQ REMOTE othe LPF per OO AMBER THERMAL 06 6 09906600 AMBER NEAR CLIP 0 2 Dy 180 0 10dB A 30 10092 45 3582 35 250Hz GREEN PRE CLIP e R L PARAMETRIC E 12 POWER GND L CH R CH BRIDGED COLOSSUS DUAL BLOCK AMPLIFIER APPLICATIONS BASIC APPLICATION This will allow you to operate separate subs independently on each channel L orR at4 2 1 Ohm at up to 1600 watts or bridged across amp to operate The Colossus Dual Mono Block amplifiers are capable of single sub up to 3200 watts at or 2 Ohms 4 2 amp 1 Ohm stereo and 4 amp 2 bridged loads Note The amp is not capable of 1 Ohm when bridged across L amp R The crossovers and HFR G1 Remote Module will operate both L amp R channels simultaneously SINGLEAMP INSTALLATION PROCEDURE 1 Connectthe amp LINE INPUTS to the Radio CD playerfull range or mono line out puts 4 Connecta 0 gauge ground cable directly to chassis ground with in 36 ofthe amp with good quality RCA interconnectcables Be sure to remove any paintor primer from the ground point Useanut b
7. output for driving mono amps damaging clipped signals to help protect the subwoofer s and amplifier Remote Output Driver circuit to turn on amplifier when Includes soft clip and full clip indications module activates Music Shaping Shapes the music signal to achieve deep bass notes as Bass Remote Features for subwoofer Level control with built 10 15Hz De in clipping indicators Bass Remote Included bas Remote features built in clipping indicators Input amp Output Level Control Allows for gain matching both allows direct bass control from in dask or under dash radio and amplifier audio signals MX 2 Deluxe High To Low Level Converter MX 4 Add A Sub High To Low Level Converter LE asite zone HIGH LEVEL FRONT HIGH REAR HIGH F amp R INPUT PASS FILTER PASS FILTER HIGH LEVEL SUBWOOFER LR amp RR INPUT OUTPUT LEVEL CONTROL CONTROL 12 dB OCT 12 dB OCT FRONT amp REAR STEREO OUTPUT 2 CONVERTER POWERED BY MAXXSONICS POWERED BY MAXXSONICS MX 4 ADD A SUB Converts High Level speaker wires to Ultra Clean Converts High Level OEM speaker wires to Ultra Clean RCA Low Level Low Level Outputs Outputs High Level Inputs Accepts all types of High level Inputs High Level Inputs Accepts all types of High level Inputs including including floating ground and high voltages up to 30 volts floating ground and high voltages up
8. time TIP Use the same approach when installing head units equalizers or any audio equipment for that matter run short individual grounds from each piece directly to the vehicle chassis to minimize ground loops and system noise All power ground and speaker connections should be crimped and soldered for reliability Make sure that none of the cable insulation can chafe against exposed metal in the vehicle causing short circuits to the chassis WIRE LENGTH SYSTEM AMPERAGE 7 10 ft 10 13 ft 13 16 ft 68 85 Safe connection sequence After all cables are run connect speaker wires to the speakers and amplifiers then run and plug in RCA cables Next connect all power ground and remote turn on leads Now connect all 12 volt cables to the amplifier s and distribution blocks and fuse holders Finally connect the main 12 volt cable to the battery with the main fuse removed and we are almost ready to power up the system NOTE This Matrix is a general rule of thumb Please refer to the manufacturers specific requirements Colossus specifications can be found on page 6 39nv9 Your Electrical System The Hifonics Colossus is a 3200wrms amplifier Your stock electrical system is not capable of providing the required Voltage and Amperage to this amplifier You should contact a reputable battery and alternator store or manufacturer for the proper upgrades to successfully power this model amplifier Ignoring this warning and
9. HIFONICS A U POWER FROM THE GODS CULUSSUS AMPLIFIER SERIES COLOSSUS HIGH PERFORMANCE AMPLIFIER SERIES The Hifonics Colossus has been designed to a very high level of performance with features unavailable in any other product The Colossus has variable crossovers builtin with added touches such as Subsonic F ilter Parametric Bass Equalization Phase Shift Balanced Line Inputand a Remote Level Control Module thatallows bass control from reach ofthe drivers seat To insure years of listening pleasure all amplifiers have a built in diagnostic mode that will detect shorted speaker leads low impedance dangerous high temperatures DC shorts and will shutdown the amp to help preventserious damage new feature for this series is the Clipping LED indicator This indicator is located on the amplifier end panel and Bass Remote Control Module This LED alerts the user when the amp reaches soft clipping and allows the user to correct the settings prior to reaching hard clipping and shutting the amp down INDEX PAGE General Installation 1 1 1 Amplifier Feature Descriptions 2 COLOSSUS Dual Mono Block Amplifier Applications eene nnne nnne nennen 3 Single and dual sub applications independentand bridged mode applications Setting Up Systems After Installation For Best
10. Purchase the best quality RCA cables you can afford for reliability and less engine noise interference in the audio system Installation AV L WOOD It is highly recommended that the amplifier be mounted to a board of MDF or other solid structure using the 4 mounting screws provided Avoid mounting the amplifier to metal as this can introduce noise and other unwanted issues When mounting the amplifier ensure that it is mounted HORIZONTALLY as shown in the diagram above for optimal heat dissipation Mounting amplifiers to speaker enclosures is not recommended as this can cause damage to the amplifier components When choosing a location for mounting the amplifier ensure that you check for clearance from wires gas tank electrical devices and brake lines etc General Run the wiring so that RCA cables are atleast 18 away from power and speaker cables Keep RCA cables away from electrical devices in the vehicle that can cause electrical noise such as electric fuel pumps emission control modules and other on board electronic modules Power and ground connections see the features matrix on page 6 for proper gauge cables per amplifier Use a sufficient gauge power cable and ground cable using the chart below as reference to what size wire you require Colossus amplifiers require at least 2 gauge power wire In a multi amplifier system add the total value of the manufacture recommended fusing to get your total system amperage Some app
11. TE LEVEL 5 TO BATTERY 12v 300 AMP FUSE SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE General Atthis point you are ready to get more specific on the settings for your amplifier P lease follow the settings in the order they are presented to reduce the risk of damage to your audio equipment Phase The variable P hase adjustment allows you to change the relative time that the waveform meets your ear With standard subwoofer installations where the subwoofer is behind you the Phase should generally be at 0 When subwoofers or woofers are in the kick panels or door panels the Phase adjustment is useful in delaying the timing of the wave meeting your ear by adjusting the potentiometer to 180 degrees Subsonic This setting acts as a low frequency cut off for your system bass reproduction The point that you set it at cuts off any frequencies from reproduction beyond this point The 12 o clock position is a great starting point EXAMPLE If you adjust the Subsonic to 25Hz the amplifier will not play frequencies below 25Hz but will play frequencies from 25Hz to the chosen Low Pass frequency Low Pass The Low Pass control acts as a ceiling and doesn t allow frequencies to the right of the desired setting to be reproduced The 12 o clock position is a great starting point EXAMPLE If you adjust the Low Pass to 80Hz the amplifier will not play frequencies above 80Hz but will play frequencies from 80Hz to the chos
12. attempting to run the Colossus on your stock electrical system without the necessary upgrades can cause damage to your amplifier and may void your Warranty For more information on upgrading your electrical system please review the Car Audio 101 Tutorials located on our YouTube page at www youtube com maxxsonicsusainc AMPLIFIER FEATURE DESCRIPTIONS The Hifonics Colossus is capable of 4 2 amp 1 Ohms stereo per channel APOWER LED indicates the powered up and turned on condition 4 amp 20hms mono bridged operation All HiFonics amplifiers feature a comprehensive diagnostic system with speaker lead short circuit thermal over load and amplifier DC faults The inputsensitivities for rated output powers are variable from 0 2 voltto indicated by PROTECT LED s The Colossus features a new clipping 9 volts led indicator that changes colors as the severity of the clipped signal increases All crossovers are fully variable in their respective ranges Crossoverfilterslopes are 24 dB octave for mono filters CONTROL FEATURE DESCRIPTIONS SUBSONIC The variable Subsonic filter is fully adjustable from 15Hz to 35Hz LOW PASS FILTER The low pass filter is fully adjustable from 35Hz to 250Hz PARAMETRIC BASS EQ BOOST The bass boostis fully adjustable from to 10db BANDWIDTH The bandwidth is fully adjustable from narrow to wide FREQUENCY The frequency is fully adjustable from 30Hz to 100Hz BALANCED INPUT Accepts balanced
13. conditions 1 sort circuit on the loudspeaker leads 2 An internal amplifier fault that causes DC offset on the loudspeaker output Should the amplifier go into diagnostic mode simply disconnect all and speaker leads while keeping 12 volt power ground and remote leads connected 1 Now turn the amplifier back on and if the diagnostic LED lights the amplifier has an internal fault 2 If not plug RCA cables back and reset the amplifier If it goes into diagnostic now the fault lies in the input either with bad cables or source unit 3 If the amplifier seems ok with RCA cables plugged in connect the speakers one at a time and if one of speaker or its wiring is faulty it will activate the diagnostic system 4 If the amplifier is still in Protection mode after the above steps remove all RCA s and wires from the amplifier Take a 12 length of speaker wire trim the plastic off of each end exposing the wire Now connect one end of the wire to the12V on the amplifier and connect the other to the Ground on the amplifier You will have a brief spark indicating that the Capacitors have been discharged and the drivercard has been reset Remove the jumper wire and reconnect your Power Ground and Remote wires Attempt to power the amplifier up like normal In some cases this can Reset the amplifier if permanent damage has not previously been done Amplifier heatsink overheating The amplifiers will shut down when the heatsink t
14. emperature reaches 80 degrees centigrade and turn back on once the unit has cooled down below that point Causes of overheating 1 Inadequate cooling relocate or remount to provide better natural airflow over the fins 2 Driving high power levels into low impedances back off on the volume control and or make sure you are not loading the amplifier with less than the recommended loudspeaker impedance 3 Excessive voltage drop can also cause overheating Low output power 1 Check that level controls have been set up properly 2 Make sure that the battery voltage as measured the amplifier s 12 volt and ground terminals is 11 volts or more 3 Check all 12 volt and ground connections Fuses blowing 1 The use of loudspeaker impedances below the recommended minimums will draw more current check 2 Ashorton the main 12 volt cable from the battery to the vehicle chassis will cause the main fuse to blow 3 If an amplifier fuse blows continually with only 12 volt ground and remote leads connected the amplifier may be faulty System does not turn on 1 Check all fuses 2 Check all connections 3 Measure the 12 volt and remote turn on voltages the amplifier terminals If these are non existent or low take voltage measurements at fuse holders distribution blocks the head unit s 12 volt and remote leads to localize the problem 4 If the HIFONICS lettering is illuminated but you do not have Power or Protecti
15. en Subsonic frequency Parametric Bass EQ This feature allows for selection of frequency enhancement width of enhancement and value of enhancement This feature provides impact to your bass but if not adjusted correctly it can be over used and cause damage to your subwoofers and amplifiers FREQ The Frequency adjustment for centralized enhancement is selectable from 30Hz to 100Hz BANDWIDTH Setting this adjustment all the way to the left will limit the focus of your enhancement to only the closest frequencies to your FREQ setting As you turn further clockwise you will begin to enhance more frequencies above and below your centralized FREQ setting BOOST This setting adjusts the amount of enhancement for the desired FREQ setting and BANDWIDTH and is variable from OdB to 10dB In most cases an enhancement from 9 o clock to 12 o clock is ideal paying close attention not to enhance past the 12 o clock position at high volume WARNING This is the most dangerous setting and can increase the risk of clipping and distortion which can damage your amplifier and subwoofer s if set too high Monitor the clipping indicators on the amplifier and or HFR G1 Remote Module Level GAIN Control Setup Ensure that the Level is turned completely to the left prior to turning the system on Next you should insert a CD or cassette that you are familiar with to use as a reference and turn the head unit volume control to about 8096 of its full setting The system sound
16. g RCA s back and investigate the source driving the amplifier componentata time Aticking or whine that changes with engine RPM 1 This problem could be caused by radiation pickup of cables too nearto a fuel pump ora distributor for instance relocate cables 2 Checkthatthe head unitground is connected straightto the vehicle chassis and does notuse factory wiring for ground 3 supply the head unitwith a clean 12 voltsupply directly from the battery instead of using a supply from the in dash wiring fusebox Aconstant whine This type of noise can be more difficultto pinpoint butis usually caused by some kind of instability causing oscillations in the system 1 Checkall connections especially for good grounds 2 Make sure thatno speaker leads are shorting to exposed metal on the vehicle chassis 3 RCA cables are notorious for their problematic nature so check thatthese are good in particular the shield connections HIFONICS COLOSSUS DUAL MONO AMPLIFIER FEATURES iE OUTPUT POWER RATING TRUE RMS 144 4 Ohms 2 Ohms 1 Ohm 4 Ohms Bridged 2 Ohms Bridged ELECTRICAL SPECIFICATIONS Slow Un Mute Turn On Soft Start Dampening Factor Signal To Noise Ratio A Weighted THD amp Noise Variable Input Level Control Unbalanced Input Impedance Unbalanced Power Protect L E D Pre Clip Green Soft Clip Amber Hard Clip Red PROTECTION DC Speaker Short Thermal Overload MOSFET
17. level will of course be very low and the following procedures will help you to match the amplifier input sensitivities properly to the head unit output signal level Turn the level control up slowly till you hear distortion then back off a few degrees on the control If at any point your amplifier goes into protection you will need to turn the Level to the left a bit and then try again If you reach a point where the output does not increase stop turning the Level control to the right as amplifier subwoofer combo has reached its maxx output in this application Your Clipping Indicators on the end panel of the amp and on the HFR G1 Remote Module should be monitored closely during this process as they will indicate clipping and distortion that your ear may not hear It is common to see the LED light up GREEN for pre clip and is nota concem But when the LED color changes to AMBER you will wantto reduce the LEVEL or BOOST a bit until this condition is no longer experienced Sit back and enjoy the music TROUBLESHOOTING SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault Description of the Diagnostic system built into all HIFONICS amplifiers The diagnostic system will shut down the amplifier until reset by turning the head unit off and back on This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following
18. lications may require multiple runs of power wire to meet the system requirements In multi amplifier systems itis advisable to mount a large enough fuse right at the battery and run one or multiple 12 volt power cables to a fused distribution block near the amplifiers It is then a simple matter to connectthe 12 volt terminal of each amplifier to the distribution block During this process please ensure that the main power fuse is removed to avoid shorting the electrical system The main fuse must be within 12 of the vehicles battery Ground each amplifier with as short a ground lead as possible directly to the vehicle chassis using at least 4 gauge wire or equivalent to the size of the amplifiers power wire Use a ground distribution block if you wish but it is extremely important to keep the main ground lead from this distribution block to the chassis as short as possible not more than 12 The ground connection integrity to the chassis is very important and the best way to achieve a good solid electrical and mechanical contact is to use a large round crimp lug crimped and soldered to the ground cable The next step is to scrape the paint off the vehicle chassis slightly larger than the ground lug at the connection point Drill a clearance hole in the chassis the same size as the lug hole and use a bolt spring washer and nut to securely fasten the ground lug Use petroleum jelly to coat the bolt lug connection to prevent oxidization with
19. line inputs from 0 2 volts to 18 volts for an optional balanced line driver LINE INPUT Accepts unbalanced RCA inputs from 0 2 volts to 9 volts LINE OUTPUT The unbalanced RCA outputs are identical to the signal supplied to the amplifier LEVEL The input level control allows you to match the amplifier input sensitivity to the output level of the RADIO CD source from 0 2 Volts to 9 volts when using unbalanced RCA and 0 2 volts to 18 volts with the balanced input PHASE SHIFT The Phase Shift is fully adjustable from 0 to 180 degrees SYSTEM DIAGNOSTICS The amplifier has built in monitoring devices and protection circuits that monitor all vital functions of the amplifier The diagnostics light do not come on to indicate there is a failure they come on when they detect an improper operation THERMAL The amp has an internal temperature sensor that will automatically shut off the amp if it reaches dangerous temperature levels and the LED will be Amber in color DC PROTECT Short Circuit the unlikely event the amp should internally fail the amp will shut down to prevent a DC voltage output to the Speakers or sub and the LED will be Red in color Clipping While adjusting the amplifier the LED may light up Green indicating P re Clip Amber indicating Soft Clip or Red indicating Clip These indicators give the user a chance to identify incorrect settings or high distortion before it is damaging to the equipment allowing them to correct the volume
20. oltand lock washerto secure the ground cable to the chassis ground 2 Plug in the HFR G1 bass remote module into the amp REMOTE INPUT jack 3 Route 0 gauge power cable directly to the vehicle battery with an in line 300 amp fuse 5 Connectthe subwoofer s accordance to the diagrams below USING CHANNELS L amp R INDEPENDENTLY FULL RANGE STEREO LINE INPUT Y ADAPTOR Note You can use the Radio CD designated mono Des line output or a full range stereo line output For full range stereo line output you will need NOT USED optional Adapter as shown Note The amplifier is capable of d 4 2 amp 1 Ohms per channel in this configuration 2 1 55 E oo DESIGNATED MONO LINE INPUT REMOTE TURN ON aawa 1 E CHASSIS GROUND REMOTE LEVEL BATTERY 12 300 AMP FUSE USING CHANNELS L R BRIDGED FULL RANGE STEREO LINE INPUT Y ADAPTOR Note You can use the Radio CD designated mono TE gt 6 output a full range stereo line output 1 For full range stereo line output you will need It is not capable of 1 Ann optional Y Adaptor as shown gt NOT USED BRIDGED i SUBWOOFER 2 OHM MINIMUM DESIGNATED MONO LINE INPUT TURN ON t CHASSIS GROUND 5 REMO
21. on illuminated simply remove your remote wire and use a jumper wire from 12V 4 on the amplifier to the Remote connection on the amplifier If the amplifier powers on like normal then you do not have adequate voltage amperage from your Remote source to turn your amplifier on You will need to seek out a certified installer to install a relay for your amplifier If the jumper does not power your amplifier on you may have internal damage and should contact Hifonics Customer Service to locate an Authorized Repair Center Noise problems System noise can be divided into two categories hiss and electrical interference Hiss or white noise 1 High levels of white noise usually occurs when amplifier level controls are turned up too high readjust according to the procedures in section Setting up systems after installation for best performance 2 Another major problem thatcan cause excessive hiss is a noisy head unit unplug the amplifier inputR CA cables and ifthe hiss level reduces the source unitis atfault Electrical interference The inside of an automobile is a very hostile electrical environment The multitude of electrical systems such as the ignition system alternator fuel pumps air conditioners to mention justa few create radiated electrical fields as well as noise on the 12 voltsupply and ground Remember to isolate the problem firstunplug amplifierinputR CA cables ifthe noise is still present check the speaker leads if not plu
22. to 30 volts Audio Signal Sense Hardwire Turn On Audio sense detects Audio Signal Sense Hardwire Turn On Audio sense detects music music signals from the OEM wires and activates the MX 2 As signals from the OEM wires and activates the MX 4 As an option the an option the module also offers a remote turn on wire module also offers a remote turn on wire Remote Output Driver circuit to turn on amplifier when module Remote Output Driver circuit to turn on amplifier when module activates activates Mm S ONICS Accessories TI SLAVE Sw m TES TE MASTER aut Yen OFF 48 MODE LOW PASS RED CLIP OUTPUT TEST TONE SUBSONIC FILTER GREEN 9V LEVEL 65Hz FILTER 24 dB OCT 24 dB OCT MAXX LINK MLX 100 Pi ee 0 0 0 3 4 7 7 4 9v 0 2V 0 180 098 10 dB AN 30Hz 100Hz I4 INPUT PHASE BOOST BANDWIDTH FREQUENCY LEVEL L parametric BASS Ea BYPASS 1 2008 GREEN 9V NORMAL LEVEL 2 MI 7 The Maxx Link allows you to Link or Strap two matching mono amps do not already have the Master Slave feature built in This allows you to use two amps on one subwoofer use two amps to power multiple subwoofers or connect as many amplifiers as you want to power as many subwoofers as you want and have only one Pre Amp to control all of the amplifiers The benefits are that you
Download Pdf Manuals
Related Search