Harbor Freight Tools 93920 User's Manual
Contents
1. 8 x 10 GREENHOUSE WITH TWO VENTS ASSEMBLY INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http Awww harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 Contents UNPACKING esc eirateataeeaeraaennencuentarteanaen canine natnannanbasiuiaananenpaeumeni 2 SFECIFICATON S roopan ENRE 3 SAVES Ihis WIN AA ose cisc ccs cs tcepes cans ects annaa 3 GENERAL SAFETY WARNINGS AND PRECAUTIONS 3 BASE ASSEMBLY seccuesccsesceseesetesusnsesesasdvexetasuanss seeesuverenaceuesestes 5 FRAME ASSEMBLY aicciecccteeceeevecctecwesscaceccesveccie ses sueiceccesvewseesesauc 6 Assembling the Outer Frame cccsccceseccesecenseceneecenesenseeeneseaes 6 Assembling the Roof Frame ccccesseeeseenseeseeessenssenseeeeonseonseees 8 Assembling the Studs and BracCes ccccsscseeseeeeneeeeseeeeeeeeaeeeeenens 9 Assembling the Roof Studs and Braces ccssccsssessseeeeseseeeeeees 12 Assembling the WINCOW ccscssssesseessseeseessenssenseesseessenssesseneees 13 Assembling the WO OLS cases cccseseceastnewessnecceneenatnande2. Remove the protective film from both sides of all panels 20a 20b 3 The Roof Panels 48 and the Roof Window Panel 50 will need to be placed as shown in the illustrations above The top edges of these panels need to be placed up under the edge of the Crown 15a 15b or the Window Support Beam 36 4 One at atime place each Transparent Panel 47 49 51 55 in its proper location on the Ceiling and Frame of the Greenhouse Then secure the Transparent Panel in place using the quantity and location of Panel Clips 67 as shown in the Panel Installation Diagram next page Also refer to the panel clip installation instructions in the following step Panel A Clip 67 7 f G i Transparent Panel 5 Be careful Panel Clip 67 ends may be sharp and may spring back To attach Panel Clips a Place the two loose ends of the Clip into the groove in the frame b Swing the center portion of the Clip up against the panel c Two edges of the Clip swing under the edge of the panel and the center edge holds the panel in place SKU 93920 For technical questions please call 1 800 444 3353 Page 15 Panel Installation Diagram Panel Clip 67 Location SKU 93920 For technical questions please call 1 800 444 3353 Page 16 INSPECTION MAINTENANCE AND CLEANING 1 BEFORE EACH USE inspect the general condition of the Greenhouse Check for loose screws misalignment or binding of moving parts cracked
3. 28 14 over the heads of the three bolts on the Top Doorway Beam a the Door Rail on the Doorway Beam then tighten the LZ 28 uts 5 Attach a Corner End Cap 68 to the top outer corner of each Corner Stud 1 The 14 spots requiring a Hold 26 down Connector 44 are marked with a plus Figure A 6 Assemble both Side Ceiling Plates 20a 20b to one an other f Attach a Side Ceiling Plate Ass y 20 flat against the inside of two Corner Studs 1 Make sure that the gutter on the Side Ceiling Plate is oriented correctly see Figure A inset SKU 93920 For technical questions please call 1 800 444 3353 Page 7 At this point the completed section of the frame will likely need support Attach the second Ceiling Plate the same way Attach a Corner Bracket 26 at the top of each Corner Stud 1 so that the bracket faces upwards see diagram to the right Leave the bottom holes of the two rear Corner Brackets 26 empty to allow the rear brace to be attached to those holes in the next step Attach the Rear Brace 23 to the inside of the two Corner Brackets 1 that are over the Rear Floor Plate 16 Attach each end to the lower hole on the Corner Bracket 26 using a Long Bolt 60 and Nut 61 See Figure A Assembling the Roof Frame Figure B At the side of the Greenhouse Assemble the Front Crown 15a to the Rear Crown 15b using the attached bracket Attach the Front Right and Front Left
4. Right Crown ea Side Diagonal Tr Z Rear Left Crown can ia Z Left Doorway an Front Diagonal Pe Z Right Doorway a an A e Rear Left Stud 5 4 Corner Bracket E Rear Right Stud 54 Outer Door Frame 52 Front Center Top P Top Doorway aun A 2 Center Door l Kage Top Window ee 15b Rear Crown Aq ieee 33 Frame 11 L 2 tan Bottom Window ee 17 Front Floor Plate 79 EL 1 35 Frame He 2 er Window Support 18a Side Floor Plate A 10 ZA 2 36 Boa 2 2 Door Slide a Support E 38 windowsos h 2 SKU 93920 For technical questions please call 1 800 444 3353 Page 18 PAR continued Part lengths are approximate and rounded to the nearest inch PART DESCRIPTION PART DESCRIPTION Top Center Door Top Bottom 2x1 Front Rear Base l Long Door Support Bolt 61 Nut 174 x Door Support 45 Base Bolt onan Spacer a Door Bottom 1 09 y 1 11 47 Wall Panel x4 111x Roof Panel 4 9 49 Front Rear Side 117x Panel Roof Window Banc co Corner End Cap Window Pane i s el Gutter End Cap cad Rear Center 1711 x Right Rail End Panel 6 8 SE zo Riera End gg O0 cemer 2x9 2 71 Left Rail End Cap Panel Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 93920 For technical questions please call 1 800 444 3353 Page 19
5. S connection All Side Studs 12 marked with an ZA asterisk are assembled with one Long Bolt K 60 in the middle of the slot Figure C 1 Attach the Rear Left Rear Right and Rear Center Studs 8 9 amp 10 to the outside of the Rear Floor Plate 16 and Rear Brace 23 Slide a Hold Down Connector SKU 93920 For technical questions please call 1 800 444 3353 Page 9 44 under the base and over the Bolt at each Floor Plate 16 connection Use Long Bolts 60 for the Rear Brace 23 connections 2 Attach the tops of the Rear Studs 8 9 amp 10 to the Rear Right and Rear Left Crown Beams 4 5 For the Rear Center Stud 10 usea 4 9 Top Center Connector 39 to connect to the Crown N A Beams as shown to the right YIN 3 Refer to the Note in Figure C Attach the two Side Studs 12 in the center of each side without asterisks in Figure C to the outside of the frame Make the 10 39 bottom connections using a Long Bolt 60 for later assembly of the Side Diagonal Brace 22 Slide a Hold Down Connector 44 under the base and over the Long Bolt at each bottom connection but do not install a Nut 61 over the Long Bolt yet 4 Refer to the Note in Figure C Attach the two Side Studs 12 near the corner of each side with asterisks in Figure C to the outside of the frame Slide a Long Bolt 60 into each slot for later Side Diagonal Brace 22 assembly Slide a Hold Down Connector 44 under the base a
6. 30 with the rollers on the top Front view of the door 6 Insert a Door Bottom Slider 64 into each end of the Bottom Door Frame 32 Make sure that the Sliders are assembled the correct way with the gap facing the back of the door see diagram to the right Attach the Bottom Door Frame 82 to the Outer Inner Door Frames 27a 27b using two Screws 57 on each side the one on the top into the Bottom Door Frame 32 and the bottom one into the Door Bottom Slider 64 T Raise the assembled Door up and insert the first roller of its Door Slider 29 onto the Door Rail 28 Carefully align the first Bottom Door Slider 64 over the edge of the Front Floor Plate 17 see illustration to the right Carefully slide the door over and align the other top Roller and bottom Slider as you did the first ones 8 Assemble and install the right door by following the preceding Side view steps except place the Outer and Inner Door Frames 27a 27b on the opposite sides as explained in step 3 9 Once both doors are installed install a Short Bolt 59 and Nut 61 into the hole on the ends the Door Rail 28 to prevent the doors from sliding off the rails Attach the Right and Left Rail End Caps 70 71 onto the ends of the Door Rails SKU 93920 For technical questions please call 1 800 444 3353 Page 14 Installing the Transparent Panels 1 Panel Clips 67 are used to secure the Transparent Panels in place on the Green house 2
7. Crown Beams 2 15 3 to the outside of the Crown Ass y 15 with the angled edges towards the top See diagram to the right viewed from under the Crown facing forward Q 3 Attach the Top Doorway Beam 14 and Door Rail 28 assembly to the outside opposite the Crown of the Front Right and Front Left Crown Beams 2 3 Attach the Front Center Top Stud 13 to the center of the Top Doorway Beam 14 SKU 93920 For technical questions please call 1 800 444 3353 Page 8 5 Attach the Front Center Top Stud 13 to the Front Crown Beams 2 3 using the Top center Connector 39 as shown below right 2 3 6 Attach the Rear Crown Beams 4 5 to the Crown N Lo 15b in the same fashion as the Front Crown Beams in step 2 A AN 7 Attach a Corner End Cap 68 onto the outer end of each Crown Beam 2 5 Cover the gaps between 13 39 the Crown Beams between 2 3 amp 4 5 with a Peak Cap 72 in each You may desire to use some silicone not included to secure the Peak Caps 72 in place 8 With two assistants lift the Crown Assembly and place the Crown Beams 2 5 on top of the Corner Brackets 26 See Figure B Secure each corner in place with the Crown Beams on the outside of the Corner Brackets Assembling the Studs and Braces The 13 spots requiring a Hold down Connector 44 are marked with a plus Note All Side Studs 12 with no asterisk are assembled using a Long Bolt 60 for the bottom
8. ctsonsvsrsuccaveceutccnducusts 13 Installing the Transparent Panels ccsscessesesseeseeeneseneeeneeeneeeeees 15 Panel Installation Diagram cccccsscessseeseeesesseeeeensseneeeeseeeseneeeees 16 INSPECTION MAINTENANCE AND CLEANING 17 PARTS CIST sacra ee secrete ce EE EANA EEA 18 UNPACKING When unpacking check to make sure all the parts shown on the Parts Lists at the end of this manual are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SKU 93920 For technical questions please call 1 800 444 3353 Page 2 SPECIFICATIONS Overall Dimensions 120 L x 961 2 W x 869 8 H Aluminum Frame maa ae Sheets Aluminum Thickness Thickness 0 088 038 Polycarbonate Sheet Thickness 0 165 Weight 154 Ib Save This Manual You will need this manual for the safety warnings and precautions assembly inspec tion maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY WARNINGS AND PRECAUTIONS 1 KEEP WORK AREA CLEAN AND DRY Cluttered damp or wet work areas invite injuries 2 KEEP CHILDREN AWAY FROM GREENHOUSE Do not allow children to play in or climb on this product Although this gree
9. e Nuts 61 holding the Window Support Beam 36 in place and slide the Window Support Beam 36 up to touch the window Secure it in place 9 Repeat steps 1 8 for the other window Assembling the Doors The doors are assembled using the Door Screws 57 The Screws thread directly into the rounded portions of the parts in the center of the doors 1 Place an Outer Door Frame 27a with the slotted side down Attach two Center Door Frames 31 to the Outer Door Frame 27a Assemble them with the rounded portion facing the front as shown to the right 2 Attach an Inner Door Frame 27b to the other side of the Center Door Frames 31 in the same way SKU 93920 For technical questions please call 1 800 444 3353 Page 13 3 Orient the assembled door frames for so that the Outer Door Frame 27a is on the left and the Inner Door Frame 27b is on the right This is the assembly used for the left door the right door will be assembled later with the Outer and Inner Door Frames on the opposite sides outer on right inner on left All illustrations show the left door assembly 4 Attach the Top Door Frame 30 to the top of the Outer Inner Door Frames 27a 27b Make sure that the rounded portion faces the front and that the flange where the pane will sit faces down towards the center of the door see the diagram to the right 5 Using two Short Bolts 59 and two Nuts 61 attach the Door La Slider 29 to the Top Door Frame
10. e frame e Assemble on a clear calm day Wind may damage the Greenhouse and will make assembly difficult Front Floor Rear Side Floor Plate 17 Plates 16 18a 18b Cross Section Assembling the Outer Frame 1 Use the bracket built into Side Floor Plate A 18a to attach Side Floor Plate B 18b Repeat for the second pair of Side Floor Plates Lay all Floor Plates 16 18b out on top of the base with the flanges facing the outside of the greenhouse as shown above Make sure that the Front Floor Plate 17 is on the side that you want your door to be located 2 There are four Corner Studs 1 to be attached to the Floor Plates 16 18b the end with two holes should be at the bottom Attach one Corner Stud 1 on the outside of each corner using two Bolts As shown above 1 slide a Hold Down Connector SKU 93920 For technical questions please call 1 800 444 3353 Page 6 44 up under the rail and over the end of the Bolt 59 then 2 secure it using a Nut 61 Use two Hold Down Connectors for each Corner Stud 3 Remove the Nuts 61 you used in step 1 to assemble the Side Floor Plates 18a 18b install a Hold Down Connector 44 over the end of each Bolt 59 and rein Stall all Nuts 61 4 Place three Short Bolts 59 and Nuts 61 into the holes on the Top Doorway Beam 14 Do not tighten them yet While making sure that the profiles of the parts are oriented as shown to the right slide the slot on the Door Rail
11. erisk are assembled with one Short Bolt 59 in the slot above the Long Bolt s 60 All Roof Studs 11 marked with a caret are assembled with two Long Bolts 60 in the slot All Roof Studs 11 not marked with a caret are Assembling the Roof Studs and Braces assembled with only one Long Bolt 60 in the Slot 1 Figure D Attach all Roof Studs 11 to the outside of the Front Rear Crown 15a 15b Leave the bottom ends of the Roof Studs unattached for now Slide one Short Bolt 59 into all the Roof Studs 11 marked with an asterisk above Slide two Long Bolts 60 into the Roof Studs indicated with a caret above Slide one Long Bolt 60 into all the Roof Studs not marked with a caret above Secure the ends of all Roof Studs 11 to the outer top edge of the Side Ceiling Plates 20a 20b using Short Bolts 59 Attach Roof Braces 25 to the underside of the Roof Studs 11 side by side using the Long Bolts 60 included in the last step Secure the ends of the Braces first then secure the centers Slide a Window Support Beam 36 onto two Roof Studs 11 marked with an aster isk with the predrilled holes on the underside and the flat side facing the Crown 15a 15b Use the extra Bolts 59 to secure the Beam loosely in place Repeat for the other Window Support Beam 36 At this time verify that the Door Rail 28 is oriented correctly with the rounded edge facing up see n
12. g by 2 5 23 4 deep The floor of the hole must be level and square The diagonal dimensions from corner to corner should each be 13 2 Assemble the Base outside the hole as shown below Note that the angled edges of the Base Plates 40 41a 41b need to face the corners of the base Use Base Bolts 45 Base Nuts 46 and Connectors 42 43 to secure the pieces together Base Assembly 3 With assistance lower the Base into the hole The diagonal dimensions from out side corner to outside corner must be equal for the base to be square 4 Fill the hole around the outside of the base with soil 5 This base will need to be filled with about 17 18 cubic feet of gravel or another ap propriate fill material not provided The gravel should reach up to about 1 2 3 4 below the lip of the base SKU 93920 For technical questions please call 1 800 444 3353 Page 5 FRAME ASSEMBLY e Unless noted otherwise all frame parts will be attached using the Short Bolts 59 and Nuts 61 provided Bolts should all be assembled with their heads facing the outside of the greenhouse Tighten Nuts only about 1 4 turn past finger tight be careful not to overtighten e Lay out all parts by number prior to assembly e An assistant or an appropriate support not included will be useful to keep the partially assembled parts upright during assembly Two assistants should be used to assemble the Crown pieces to the rest of th
13. le suddenly Do not allow debris to accumulate on top of the greenhouse If snowfall is expected place additional supports not provided underneath the Crown 15a 15b NEVER enter a greenhouse with accumulated debris on top WARNING The warnings precautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur The operator must understand that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SKU 93920 For technical questions please call 1 800 444 3353 Page 4 BASE ASSEMBLY IMPORTANT READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING e The first step in assembly is to assemble a proper base The greenhouse must be properly supported to help prevent property damage and injury in the event of strong winds or inclement weather Wind and ground conditions may vary from site to site and may affect the practicality and effectiveness of anchoring methods substantially e Be certain to check with local authorities to obtain all required building permits and to familiarize yourself with any building codes that may apply e Decide on a location for the greenhouse The location should be a level well lit area that is sheltered from the wind The door of the greenhouse should not open towards the prevailing wind if possible 1 Excavate an area for the base of the greenhouse The area must be 8 2 wide by 10 2 lon
14. nd over the Bolt before installing the Nut 61 at each bottom connection 5 Attach a Side Diagonal Brace 22 to the lower hole of a Corner Stud 1 on the inside with the TOP arrow pointing towards the Corner Stud as shown in Figure C Use a Long Bolt 60 to attach the Brace Attach the other three Side Diagonal Braces 22 to the other Corner Studs 1 in the same manner 6 Attach the center hole of each Brace to the Long Bolt 60 in the center of the Side Studs 12 designated with an asterisk in Figure C This Bolt 60 was included in step 4 above T Attach the bottoms of all four Side Diagonal Braces 22 to the Long Bolts 60 installed at the bottoms of the remaining Side Studs Right Left Doorway Doorway to Stud 7 Stud 6 to Corner Corner Stud 1 Stud 1 i l iS i _ j Ml um Front Floor Plate 17 View from above 8 Install the Left and Right Doorway Studs 6 amp 7 to the outside of the frame so that they rest flat against the frame Their orientation should be the same as shown above Slide a Long Bolt 60 into each slot for later Front Brace 21 assembly Make the bottom connections using a Long Bolt 60 for later assembly of the Front Diagonal Braces 24 Slide a Hold Down Connector 44 under the base and over SKU 93920 For technical questions please call 1 800 444 3353 Page 10 10 11 12 13 the Long Bolt at each bottom connection but do not install a Nut 61 o
15. nhouse does include some protective covers there are still some exposed sharp edges In addition protective covers may fall off in time Children must be supervised if allowed near the greenhouse 3 DO NOT ASSEMBLE THIS PRODUCT IF UNDERTHE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not attempt to assemble this product 4 USE EYE PROTECTION Wear ANSI approved safety impact eye goggles when assembling this product ANSI approved safety impact eye goggles are available from Harbor Freight Tools 5 DO NOT OVERREACH Keep proper footing and balance at all times to prevent tripping falling back injury etcetera 6 STAY ALERT Watch what you are doing at all times Use common sense Do not attempt to assemble this product when you are tired or distracted from the job at hand SKU 93920 For technical questions please call 1 800 444 3353 Page 3 10 11 12 13 14 15 16 17 CHECK FOR DAMAGED PARTS Before using this product carefully check that it will operate properly and perform its intended function Check for damaged parts and any other conditions that may affect the operation of this product Replace or repair damaged or worn parts immediately REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Only use accessories intended for use with this pr
16. oduct Ap proved accessories are available from Harbor Freight Tools MAINTAIN THIS PRODUCT WITH CARE Keep this product clean and dry for better performance MAINTENANCE For your safety service and maintenance should be performed regularly by a qualified technician USE THE RIGHT PRODUCT FOR THE JOB Do not attempt to force a small product to do the work of a larger industrial product There are certain applications for which this product was designed It will do the job better and more safely in the manner for which it was intended Do not modify this product and do not use this product for a purpose for which it was not intended MAINTAIN A SAFE WORKING ENVIRONMENT Keep the work area well lit Make sure there is adequate surrounding workspace Avoid high traffic areas Always keep the work area free of obstructions grease oil trash and other debris PROPER GREENHOUSE LOCATION Make sure the Greenhouse is located on a flat level surface WARNING This product contains or produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq THIS UNIT CONTAINS PIECES WITH SHARP EDGES The machined edges of the aluminum parts and the ends of the panel clips may be sharp Handle all parts carefully SNOW DEBRIS ACCUMULATION HAZARD The heavy weight of accumulated snow or other debris can cause parts of this greenhouse to buck
17. or broken parts and any other condition that may affect the safe operation of the Greenhouse Ifa problem occurs with the Greenhouse have it corrected before further use Do not use damaged equipment 2 TO CLEAN Wipe with a damp cloth using a mild detergent Do not use cleaners that are combustible corrosive or not compatible with aluminum 3 WHEN STORING Keep the Greenhouse in a box and in a clean dry location PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF RE PLACEMENT PARTS THERETO SKU 93920 For technical questions please call 1 800 444 3353 Page 17 PARTS LIST Lengths given are approximate and rounded to the nearest inch PART DESCRIPTION PART DESCRIPTION Front Right Crown os Side Ceiling Plate fai Front Left Crown ra sagr Sa Rear
18. umber 4 on page 7 SKU 93920 For technical questions please call 1 800 444 3353 Page 12 Assembling the Window 1 Attach the Side Window Frames 34 to the Top Window Frame 33 as shown below to the right 2 Insert Short Bolts 59 into the holes at the bottom of the Side Window Frames 34 so that the threads stick out the bottom of the window 3 Remove the protective film from both sides of the Window Pane 51 Slide the Window Pane 51 into the three sided frame 4 Slide the Bottom Window Frame 35 onto the two Short Bolts 59 and the Window Pane 51 Secure it in place with Nuts 61 You may need to apply some pressure to the heads of the Bolts through the Window Pane to allow the Nuts to thread on properly 5 Attach the Window Brace 38 to the Bottom Window Frame 35 using two Window Screws 58 The holes on the Window Brace 38 should face away from the win dow 6 Slide the top edge of the Top Window Frame 33 into the slot at 33 the top of the Crown 15b see illustration to the right The win 15a dow should be aligned with the Window Brace 38 underneath 415b it Slide the window into place over the Window Support Beam 36 Gradually lower it into place 7 Using two Window Screws 58 attach the Window Stop 37 to the Window Support Beam 36 with its tab pointing towards the Crown 10 11 It should be on the underside of the Window Support Beam inside the greenhouse 8 Loosen th
19. ver the Long Bolt yet Remove the bottom Bolt from the Corner Brackets 26 at the front of the green house Install the Front Diagonal Braces 24 to the bottom hole of the Brackets on the inside using Long Bolts 60 Attach the bottom of the Front Diagonal Braces 24 to the Long Bolt left exposed on the Floor Plate 17 from the last step See Figure C Remove the second Bolt from the bottom of the front Corner Brackets 26 Con nect the Front Braces 21 to the exposed hole using Long Bolts 60 Connect the loose ends of the Front Braces 21 to the Doorway Studs 6 7 using Long Bolts 60 See Figure C Attach the Door Slide Support 19 to the Front Right Crown Beam 2 using the Long Door Support Bolt 56 and Nut 61 with the Door Support Spacer 63 between the Support and the Stud See oN Figure C inset and diagram to the right Repeat for the M other Door Slide Support 19 on the opposite side The frame should now rest square Measure diagonally from corner to corner at the top If the measurements are not equal adjust the frame as needed until square Some Nuts 61 may need to be temporarily loosened to adjust the frame properly Place the Gutter End Caps 69 onto the ends of the Side Ceiling Plates 20a 20b oriented with a gap in the bottom to allow water to drain out of the gutters SKU 93920 For technical questions please call 1 800 444 3353 Page 11 All Roof Studs 11 marked with an ast
Download Pdf Manuals
Related Search