Harbor Freight Tools 6 in. Cross Slide Vise Product manual
Contents
1. Cross Slide Vise Item 32997 AWARNING Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Visit our website at http www harborfreight com Email our technical support at tech harborfreight com Copyright 1997 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Revised Manual 11f SPECIFICATIONS 7 1 4 IN Overall Height 6 1 8 IN Maximum Jaw Opening 5 3 4 IN Longitudinal Travel 7 1 2 IN Jaw Depth 1 1 4 IN SAVE THIS MANUAL READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR OPERATING THE CROSS SLIDE VISE You will need this manual for the safety instructions operating instructions and parts list Put it in a safe dry place for future reference Keep your invoice with this manual Write the invoice number on the inside front cover SAFETY WARNINGS amp CAUTIONS WARNING When using electric tools machines or equipment basic safe2. in Figure 7 Figure 7 Locking the Vise Step 3 Tighten the SCREWS 15 until they press the GIB 14 not shown against the BASE 9 Step 4 Tighten the NUTS 16 to lock the BASE 9 in position Step 5 Repeat if desired for the unlocked Base MAINTENANCE Occasional lubrication of the Vise will ensure smooth operation and longer tool life Use a light oil for lubrication purposes Refer to Figure 8 for lubrication points Figure 8 Lubrication Points Page 10 For technical questions please call 1 800 444 3353 SKU 32997 REV 101 PARTS LIST Lock Screw M6 x 20 2 2 Jaw Plate ASSEMBLY DIAGRAM SKU 32997 For technical questions please call 1 800 444 3353 Page 11 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the ex
3. OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Page 12 For technical questions please call 1 800 444 3353 SKU 32997
4. Vise Determine the position of the Vise that will give you the safest and best access to the material clamped in the SLIDE 24 Step 1 To adjust the longitudinal fore aft axis of the Vise locate the LEAD SCREW 8 and HANDLE 1 Step 2 Turn the HANDLE 1 counterclockwise to move the MID BASE 18 and UPPER BASE 20 further towards the rear of the BASE 9 as shown in Figure 5 Upper Base 20 w Lead screw 12 and 9 H ty Figure 5 Moving Mid Base and Upper Base Step 3 Turn the HANDLE 1 clockwise to move the MID and UPPER BASE 18 amp 20 closer to the HANDLE 1 Position for best access Step 4 To adjust the cross travel side to side axis of the Vise locate the LEAD SCREW 12 and HANDLE 1 Page 8 For technical questions please call 1 800 444 3353 SKU 32997 Step 5 Turn the HANDLE 1 clockwise to move the UPPER BASE 20 to the left as shown in Figure 6 Upper Base 20 Figure 6 Moving Upper Base to the Left Step 6 Turn the HANDLE 1 counterclockwise to move the UPPER BASE 20 to the right Position for best access SKU 32997 For technical questions please call 1 800 444 3353 Page 9 Locking the Vise Your Vise BASES can be locked into position to prevent accidental movement You will need a 10mm end wrench and a Phillips screwdriver for this operation Step 1 Select which BASE 9 you want you lock into position Step 2 Loosen the two NUTS 16 as shown
5. clusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
6. on Safety goggles and ear protectors are available from Harbor Freight Tools 9 SECURE WORK Use clamps or a vise to hold the work if possible It s safer than using your hands and it frees both hands to operate the tool erii Page 2 For technical questions please call 1 800 444 3353 SKU 32997 DON T OVERREACH Keep proper footing and balance at all times MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Keep handles dry clean and free from oil and grease STAY ALERT Watch what you are doing use common sense Don t operate any tool when you are tired CHECK DAMAGED PARTS Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and other conditions that may affect its operation Any part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in the instruction manual REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to dete
7. p with the mounting bolts as shown in Figure 2 S I P D ef a N nnise Figure 2 Attaching Base to Table Step 5 Thread nuts on the mounting bolts and tighten by hand Step 6 Position the Vise a final time Tighten the mounting nuts firmly SKU 32997 For technical questions please call 1 800 444 3353 Page 5 OPERATION Clamping Center the Vise before clamping anything This will allow maximum adjustment flexibility in every direction To open the Jaws of the Vise open the SLIDE 24 by turning Step 2 the LEAD SCREW 21 as shown in Figure 3 Lead Screw re 21 Step 1 L00se Figure 3 Opening Jaws SKU 32997 For technical questions please call 1 800 444 3353 Page 6 Step 3 Insert the material to be clamped If the material is small place it over one of the runners of the UPPER BASE 20 as shown in Figure 4 This will keep the material from falling below into the Vise Upper Base 20 Figure 4 Placing Small Material Step 4 Begin to close the SLIDE 24 by turning the LEAD SCREW 21 This will tighten the Jaws of the Vise Step 5 When the SLIDE 24 touches the material you are working on tighten the SLIDE 24 only enough to ensure clamping DO NOT CRUSH the material you are working on CAUTION Do Not Over Tighten the Vise You Will Damage Your Material SKU 32997 For technical questions please call 1 800 444 3353 Page 7 Cross Sliding the
8. rmine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate machine UNPACKING If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual REF ITEM DESCRIPTION N A Cross Slide Vise SKU 32997 For technical questions please call 1 800 444 3353 Page 3 ASSEMBLY Your Vise comes partially assembled To complete assembly you will need a 14mm wrench Step 1 Place the Vise on a clear area of your workbench Step 2 Slide a HANDLE 1 onto the LEAD SCREW 8 rotating the HANDLE 1 until it fits onto the square end of the LEAD SCREW 12 as shown in Figure 1 Vise Assembly Figure 1 Handle Assembly Step 3 Attach a NUT 2 and tighten with a 14mm wrench Step 4 Locate the other HANDLE 1 and slide it onto the LEAD SCREW 12 Step 5 Attach a NUT 2 and tighten with a 14mm wrench Page 4 For technical questions please call 1 800 444 3353 SKU 32997 Attaching the Vise to a T Slot Table Step 1 You will need additional hardware sold separately to complete installation Step 2 Place the assembled Vise onto the T Slot Table Select the appropriate rows in the T Slot Table which line up with the Mounting Tabs on the BASE 9 Step 3 Insert 2 to 6 T Slot mounting bolts into the T Slot Table rails Step 4 Place the Vise on the T Slot Table in the position you want Make sure the mounting tabs on the BASE 9 line u
9. ty precautions should always be followed to reduce the risk of fire electric shock and personal injury READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1 KEEP WORK AREA CLEAN Cluttered areas invite injuries 2 CONSIDER WORK AREA CONDITIONS Don t use in damp wet or poorly lit locations Don t expose to rain Keep work area well lit 3 KEEP CHILDREN AWAY All children should be kept away from the work area Don t let them handle machine 4 STORE IDLE EQUIPMENT When not in use tools should be locked up in a dry location to inhibit rust If possible store in an area out of reach of children 5 DO NOT FORCE THE MACHINE OR TOOL It will do the job better and more safely at the rate for which it was intended 6 USE THE RIGHT TOOL Don t force a small tool or attachment to do the work of a larger industrial tool Don t use a tool for a purpose for which it was not intended 7 DRESS PROPERLY Don t wear loose clothing or jewelry They can be caught in moving parts Protective gloves and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair preventing it from getting caught in machinery 8 USE EYE AND EAR PROTECTION Use a full face mask if the work you are doing produces metal filings dust or wood chips Goggles are acceptable in other situations Wear a clean dust mask if the work creates a lot of fine or coarse dust When operating for extended periods of time use approved ear protecti
Download Pdf Manuals
Related Search