Harbor Freight Tools 5655 User's Manual
Contents
1. Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep both this manual and your invoice in a safe dry place for future reference NOTICE The Warnings Cautions and Instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Page 2 SKU 5655 REV OIc 08a 08e SAFETY WARNING amp CAUTIONS WARNING When using shop equipment basic safety precautions should always be followed to reduce the risk of personal injury and hazards READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1 KEEP WORK AREA CLEAN Cluttered areas invite injuries 2 OBSERVE WORK AREA CONDITIONS Do not use tools in damp wet or poorly lit locations Don t expose to rain Keep work area well lit Do not use electrically powered equipment in the presence of flammable gases or liquids 3 KEEP CHILDREN AWAY Children must never be allowed in the work area Do not let them handle machines tools or equipment 4 STORE IDLE EQUIPMENT When not in use tools must be locked up in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 DO NOT FORCE THE TOOL It will do the job better and more safely at the rate for which it was intended Do not use inappropriate attachments2. hold the various workpieces you will work on and the various tools you will use 2 Place the Vise on the work bench where it will be installed 3 Mark through the holes on the left and right sides of the base of the Vise onto the work bench surface Remove the Vise 4 Drill holes through the bench top in an appropriate size 5 Replace the Vise and insert appropriate size bolts through the Vise base and work bench top 6 Install washers and nuts on the bolts underneath the workbench Tighten securely To Swivel Base ll Loosen both Levers 3 on the base of the Vise by rotating them counterclockwise Swivel the Vise to the position desired 2 Tighten both levers by rotating them clockwise To Open and Close Jaws I Rotate the Handle 21 counterclockwise to open the jaws 2 Rotate the Handle clockwise to tighten the jaws To Rotate the Jaws I Open the Jaws by rotating the Handle counterclockwise 2 Rotate the Jaws in either direction to the desired position 3 Insert the workpiece in the jaws and tighten by rotating the handle clockwise 4 Tightening the jaws also tightens the Rotator 22 Jaws Soft Jaws Pipe Jaws and Cut Jaws il Select the standard jaws when clamping flat pieces which will not be damaged bv being clamped 2 For flat items which may be marred by the standard jaws either use soft jaws or use a shim between the standard jaws and the workpiece 3 For round items such as pipes rotate the
3. in an attempt to exceed the tool s capacities 6 USE THE RIGHT TOOL FOR THE JOB Do not use a tool for a purpose for which it was not intended 7 DRESS PROPERLY Do not wear loose clothing or jewelry as they can be caught in moving parts Non skid footwear is recommended Wear restrictive hair covering to contain long hair Always wear appropriate work clothing 8 USE EYE EAR AND BREATHING PROTECTION Always wear ANSI approved impact safety goggles if you are producing metal filings or wood chips Wear an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists Use ANSI approved ear protection when working in a loud or noisy environment 9 DO NOT ABUSE THE POWER CORD Protect the power cord from damage either from impacts pulling or corrosive materials Do not yank machine s cord to disconnect it from the receptacle 10 DO NOT OVERREACH Keep proper footing and balance at all times Do not reach over or across running machines 11 MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect power cord periodically and if damaged have it repaired by an authorized technician Inspect all hydraulic seals for leaks prior to use Control handle and power switch must be kept clean dry and free from oil and grease at all times Page 3 SKU 5655 12 REMOVE ADJUSTING KEYS AND WRENCHES Be su
4. jaws so that the Pipe Jaws are uppermost holding the workpiece in them 4 For short round or odd shaped items such as a short cylinder rotate the vise so that the Cut Jaws are up Insert the cylinder in the cut jaws and tighten the Handle Page 5 SKU 5655 MODEL 5655 VISE MODEL 5655 SWIVEL VISE PARTS LIST Part Description Part Description 1 Rotation Collar i Cut Jaw Screws 2 Base 13 Pipe Jaw Screws 3 Lever 14 Outer Pipe Jaw 4 Body 15 Locking Pin 5 Fixed Jaw 16 Castle Nut 6 Outer Jaw I7 Flat Washer 7 Screw 18 Cap Screws 8 Inner Pipe Jaw 19 Screw Cap 9 Inner Cut Jaw 20 Outer Cut Jaw 10 Jaw Faceplate 21 Handle 11 Faceplate Screws 22 Rotator PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NETHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER A ND OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 6 SKU 5655
5. 5 Multi Purpose Vise Model 5655 ASSEMBLY amp OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 1999 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools SPECIFICATIONS MODEL 5655 VISE Jaw Width Throat Depth a He Base Dimensions 7 5 16 x 7 5 16 Base Swivel Capacity Jaw Rotation Capacity 360 FEATURES OF THIS VISE Strong cast iron construction with hardened and ground jaws Rotating Jaws for flat jaw up or pipe jaw up working Swivel Base with double lever locks Work at any angle with combination of swivel base and rotating jaws Built in anvil Enclosed screw for maintenance free operation Rotating jaws lock in place when jaws are tightened Oe Se SAVE THIS MANUAL You will need this manual for the safety warnings and cautions assembly instructions operating procedures maintenance procedures trouble shooting parts list and diagram
6. oper electrical cord or extension cord Never operate an electrical tool unless you are plugged into a properly grounded outlet which supplies 110 120Volts We recommend you only use a circuit which is protected by a 30 amp circuit breaker or other amperage recommended by the manufacturer Crushing and Marring Overtightening or using incorrect or dirty jaws can cause damage to your workpiece Before clamping anything in this vise assure that the jaws are clean If the workpiece is softer than steel use soft jaws or shims of softer material to prevent damage to the workpiece Hammering Use caution when hammering anything in or on this vise Preferably use the ground anvil on top of the Vise as a hammering surface Do not hammer on the outer movable vise jaw as this can damage the screw Use only light hammers on relatively soft material For heavier hammering use an anvil designed for the purpose Slipping Periodically check to be sure the workpiece is tight in the Vise Twisting bending hammering and sawing on a workpiece can cause it to become loose in the vise potentially creating a hazard NOTICE No list of warnings can be all inclusive The operator must supply common sense and operate this tool in a safe manner Page 4 SKU 5655 ASSEMBLV AND OPERATION Your 5655 Vise is delivered completely assembled Installation iF Select a sturdy level work bench to install the Vise Be sure there is sufficient room around the vise to
7. re that keys and adjusting wrenches are removed from the tool or machine work surface before operation 13 AVOID UNINTENTIONAL STARTING Be sure that you are prepared to begin work before turning the start switch on 14 STAY ALERT Watch what you are doing Do not operate this machine when you are tired 15 DO NOT OPERATE THIS MACHINE WHILE UNDER THE INFLUENCE OF ALCOHOL DRUGS OR PRESCRIPTION MEDICINES 16 CHECK FOR DAMAGED PARTS Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn on and off properly 17 REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Use of any other parts will void the warranty Only use parts and accessories intended for use with this tool which are available from Harbor Freight Tools SPECIAL WARNINGS WHEN USING THIS VISE Using this Vise may create special hazards Take particular care to safeguard yourself and those around you Electrical Safety Never operate any tool if there is an electrical hazard Never operate an electrical tool in wet conditions Never operate a tool with an impr
Download Pdf Manuals
Related Search