Harbor Freight Tools 24 in. Digital Laser Level with Angle Finder Product manual
Contents
1. CEN TECH 24 DIGITAL LEVEL WITH LASER Were 331193884 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein 7 HARBOR FREIGHT 33 TOOLS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 Labels Specifications Laser Dot Accuracy Up to 98 Feet Laser Line Accuracy Up to 33 Feet AVOID EXPOSURE Laser radiation is emitted from this aperture Vial Accuracy 3 Degrees Power Source AAA Batteries Qty 2 9V Battery Qty 1 LASER RADIATION AVOID DIRECT EYE EXPOSURE Power Output lt 5mW Wavelength 650 nm CLASS Illa LASER PRODUCT This product complies with 21 CFR 1040 10 and 1040 11 CEN TECH 3491 Mission Oaks Blvd Camarillo CA USA 93011 Manufacture Date Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating an2. If the Slide Switch is in the lower position it can conceal an illuminated laser beam If the Slide Switch 18 is in the upper position the Vertical Laser Button will proj ect a vertical line and the Horizontal Dot Laser Button will project a horizontal line When the Slide Switch 18 is in the lower position the Vertical Laser Button will be covered and the Horizontal Dot Laser Button will project a simple dot beam WARNING To conserve battery power and prevent accidents move the Slide Switch 18 to the upper position and verify that both lasers are off after use REV 07g SKU 93884 For technical questions please call 1 800 444 3353 Page 5 MAINTENANCE ls Wipe the Level clean with a lint free cloth when needed 2 Store the Level in a dry location where it will not freeze or overheat 3 Before each use inspect the Level to make sure nothing is cracked or broken Do not use the Level if anything is cracked or broken Have it repaired by a qualified service technician Changing or Installing Batteries FIGURE 2 EF Battery Polarity Direction D yee Cap 14 1 To change the AAA batteries that power the Laser remove the End Cap 14 and set it aside See FIGURE 2 above 2 Remove the old batteries and replace them with two fresh batteries Make sure that you match up the positive and negative ends to the diagram on the side of the level See FIGURE 2 above Replace the End Cap 14 FIGURE 3 Ba
3. d maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference SAFETY WARNINGS AND PRECAUTIONS WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Don t expose to rain Keep work area well lit 3 Keep children away Children must never be allowed in the work area Do not let them handle the Laser Level 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job There are certain applications for which this tool was designed Do not modify and do not use this tool for a purpose for which it was not intended 6 Never direct the laser beam into the eyes of any person or animal THIS MAY CAUSE SEVERE INJURY TO THE EYE Do not look into the beam during opera tion Make certain to switch the Laser Level to OFF when making adjustments or changing the batteries Laser light when reflected off a mirror like surface can cause serious eye damage T Only use the type of battery recommended in this manual Use only AAA batteries f
4. e level changing the actual angle setting is not done by this button and needs to be performed by a qualified technician Sound This button toggles the sound When the sound is on the level will beep once when it measures any 10 increment and more than once when it reads 0 or 90 A symbol will appear above the decimal point on the display and the unit will beep to indicate that the sound is on Horizontal and Vertical Vial Use The Vials 9 10 on the level can be read by observing the bubble within If the bubble is centered in between the lines then the Vial is level REV 07g SKU 93884 For technical questions please call 1 800 444 3353 Page 4 Laser Controls Vertical Laser Button 12 Slide Switch 18 Horizontal Dot Laser Button 12 le Vertical Laser Button 12 This button turns on the vertical laser line if the Slide Switch 18 is in the upper position The vertical laser is blocked while the Slide Switch 18 is in the lower position 2 Horizontal Dot Laser Button 12 This button turns on the horizontal laser line if the Slide Switch 18 is in the upper position It can be used along with the vertical laser line to make a cross When the Slide Switch 18 is in the lower position the laser is a dot instead 3 Slide Switch 18 The Slide Switch 18 determines laser operation WARNING Point the end of the level away from people s eyes when adjusting the Slide Switch 18
5. e operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator UNPACKING When unpacking check to make sure that the product is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible SKU 93884 For technical questions please call 1 800 444 3353 Page 3 OPERATION efer to the Assembly Drawing on Page 6 LCD Display Controls On Off Holding this button down for several seconds turns the LCD display on or off The display will automatically shut off after a period to conserve battery power Hold This button keeps the same reading on the display even if the level s angle changes Everything on the display will flash except the number while the reading is being held Press the button again to stop holding the reading 0 percent This button switches the LCD display between displaying the angle in degrees and displaying the angle as a percent difference from 0 or 90 Calibrate Zero Setting This button toggles between reading 0 at the current angle and reading the actual angle Press the Calibrate button once to change the cur rent reading to 0 or 0 Press the Calibrate button again and hold it to restore the level to reading the actual angle The level will reset to reading the actual angle if it is switched off Note Actual calibration of th
6. or the Laser and a 9V battery for the digital display Do not mix old and new batteries 8 Maintain tools with care Keep tools clean for better and safer performance SKU 93884 For technical questions please call 1 800 444 3353 Page 2 9 Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired 10 Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn On and Off properly 11 Replacement parts and accessories When servicing use only identical replace ment parts Use of any other parts will void the warranty 12 Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool 13 Maintenance For your safety service and maintenance should be performed regu larly by a qualified technician 14 Use fresh batteries Weak batteries could affect the visibility of this tool Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be under stood by th
7. stration purposes only and are not available individually as replacement parts SKU 93884 For technical questions please call 1 800 444 3353 Page
8. ttery Cover 16 9 Volt Battery 3 To change the 9 Volt battery that powers the LCD 3 remove the Battery Cover 16 by first removing the Screw 15 4 Install a fresh battery making sure you match up the positive and negative terminals as shown inside the battery compartment Replace the Battery Cover 16 and the Screw 15 See FIGURE 3 above SKU 93884 For technical questions please call 1 800 444 3353 Page 6 PARTS LIST Description _ 8 Sound Button _ 9 Horizontal Dial ____ 6 0 Percent Button _ __ Part Description _ _ AAA Battery Qty 2 ASSEMBLY DRAWING 18 re 14 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARIS ING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Note Some parts are listed and shown for illu
Download Pdf Manuals
Related Search