Harbor Freight Tools 2000 lb. Capacity Foldable Engine Stand Product manual
Contents
1. from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from2. state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
3. B Steps 1 through 4 Item 69521 For technical questions please call 1 800 444 3353 Page 3 Bolt Washer 5 Slide the mounting post of Nut 10 Sh the Mounting Plate 6 into ort Pin 12 Arm 7 the collar of the Column 4 Align the holes and insert the Pin 12 6 Slide off one of the Handle 5 rubber grips and insert the Handle 5 through the large holes at the end of the Mounting Plate 6 post Replace the rubber grip 7 Attach the Arms 7 8 to the slots in the Mounting Plate 6 using the Bolts Washers and Nuts 10 Handle 5 Mounting Plate 6 Long Arm 8 Figure C Mounting Plate Installation PITTSBURGH Page 4 For technical questions please call 1 800 444 3353 Item 69521 Operating Instructions A Mounting Engine Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product TO PREVENT SERIOUS INJURY AWARNING Before attaching an engine to the stand confirm that its weight does not exceed the Stand maximum capacity 1 Lock both Legs 1 9 in lowered position 5 Place the bolts not included through with two Leg Lock Pins 15 per Leg the Mounting Plate 6 side and securely secured in place with R pins 16 tighten them into the engine 2 Remove the Pin 12 from The bolt heads must press against the back of the Arms the Column 4 l if needed use flat washers 3
4. Determine the thread type and not included as spacers length of bolts not included needed to thread into the engine block Use grade 8 bolts that are long enough to fit through the Arms and thread as deeply as possible into the engine block 7 Slowly lower the hoist engine crane 4 Align the Short and Long Arms 7 8 solo separa y P een gine with four mounting bolt weight is held by the stand Tighten the Bolts 10 and Nuts that hold the Short and Long Arms 7 8 to the Mounting Plate 6 securely locations on the engine 8 Safely release the engine from WARNING Use all four Arms when Ne hoIsvengine crane attaching an engine to the Stand 9 Slowly rotate the engine to the desired angle and insert the Pin 12 into the top of the Column 4 Rotating Engine TO PREVENT SERIOUS INJURY Be prepared for sudden engine AWARNING movement before removing Pin Stay clear of engine 1 While holding onto the Handle 5 2 Use assistance to rotate the engine and the engine to prevent it from to the desired angle and insert the accidental rotation remove Pin 12 Pin 12 into the top of the Column 4 Removing Engine 1 With assistance rotate the 3 Once the engine is properly engine to its initial position supported by the crane remove the bolts securing the 2 S th i ly to th E A ink E A oie Short and Long Arms 21 to the engine Use the crane to support all of the engine s weight directly overhead but
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference P I TTSB UR G H ITEM 69521 2000 Ib Foldable Engine Stand Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible AWARNING Copyright 2012 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Weight Capacity 2 000 Ib Face Plate 9 3 4 W x 5 7 8 H x 13 16 thick Important Safety Information Assembly Precautions 1 Assemble
6. do not start lifting the engine stand Item 69521 For technical questions please call 1 800 444 3353 Page 5 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM STAND FAILURE Do not use damaged equipment Make sure the stand is stable If any unsafe conditions are found take it to a qualified technician for service or repair 1 BEFORE EACH USE inspect the 3 Before each use check that general condition of the Stand Check hardware is securely fastened it for cracks bends in the metal signs A Checicihal the Casters are of unusual wear or any other condition that may affect its safe operation If any are found do not use the Stand 5 AFTER USE clean external surfaces of the stand with a clean moist cloth clean and turn properly 2 Keep Engine Stand clean and free of dirt or grease Folding the Stand for Storage 4 Insert the Leg Lock Pin 15 through 1 Remove the forward R pin 16 the upper hole in the Base 2 so 2 Remove the Leg Lock Pin 15 that it holds the Leg in place and lock it in place with the R pin 3 Fold up the Leg 1 9 5 Repeat for the other Leg WARNING Do not use the Stand while it is folded This is only for compact storage Record Serial Number Here Note Some parts are listed and shown for illustration purposes only and are not Note If product has
7. extended outward and Leg Lock Pins and R Pins are in place Page 2 For technical questions please call 1 800 444 3353 Item 69521 Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product A Left Leg Mounting Long amp Short 4 Place the Right and Left Leg 1 9 Wheel piste xr 107 pieces into the Base 2 lining up the Detail holes on the sides Secure in place with ml TE PA the Leg Lock Pins 15 and R Pins 16 MORG it Note The wheel housing of the Right and Left Legs 9 1 are welded at an angle from the Legs and are different from each other Be sure to insert the Legs into the Base so that the wheels will be parallel pointing forward not out to the sides 2 Attach the Column 4 to the Base 2 using the Bolts Washers and Nuts 14 ee O Do not fully tighten the Bolts in place until Step 4 Column 4 Iie Base 2 3 Align the holes of the Braces 3 on Left amp Right either side of the Column 4 hole Legs 1 9 and secure with the Bolts Washers Figure A Overall Assembly and Nuts 13 Do not fully tighten the Bolts in place until Step 4 4 Align the bottom of the Braces 3 with the holes on the inside of the Base 2 frame and secure with the Bolts Washers and Nuts 17 Tighten all Bolts from Steps 2 through 4 Figure
8. no serial number Maing P available individually as replacement parts record month and year of purchase instead Page 6 For technical questions please call 1 800 444 3353 Item 69521 Parts List and Diagram Part Description _ Qty 6 Mounting Plate 1 8 jLongArm 2 9 jRightLeg 1 Item 69521 For technical questions please call 1 800 444 3353 Qty 18 NutMs 8 Page 7 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days
9. only according to these 4 Keep bystanders out of the instructions Improper assembly area during assembly can create hazards 5 Do not assemble when tired 2 Wear ANSI approved safety goggles or when under the influence and heavy duty work gloves of drugs or medication during assembly 6 Weight capacity and other product 3 Keep assembly area clean and well lit capabilities apply to properly and completely assembled product only Use Precautions Failure to heed these instructions may result in personal injury and or property damage 1 Study understand and follow all 7 Hold Handle while removing the Pin instructions before operating this device Wear ANSI approved safety goggles 2 Donot exceed rated capacity and heavy duty work gloves during use Be AWALE Or Cynanic roading 9 Do not use for aircraft purposes Sudden load movement may briefly create excess load 10 Inspect before every use causing product failure do not use if parts loose or damaged 3 Use only on hard level surfaces 11 This product is not a toy Do not allow children to play with or near this item Lock mounting plate rotating mechanism before applying a load 12 Use as intended only 5 Assure load is centered and secured 13 Maintain product labels and nameplates to mounting attachments These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement 6 Only use when Legs are fully
Download Pdf Manuals
Related Search