Harbor Freight Tools 12V Product manual
Contents
1. PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO PARTS LIST Part Description Horn Compressor Nut amp Bolt Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 96291 For technical questions please call 1 800 444 3353 Page 62. i n not included Connection is to the line positive point of the original horn Existing vehicle fused circuit REV 08a SKU 96291 For technical questions please call 1 800 444 3353 Page 4 SKU 96291 Connection is to the line positive 4 point of the original horn Existing vehicle fused circuit Positive Ground Wiring Diagram 12 VDCi Electric Relay U CEM a O Ii not included 30 151 30 A 12 VDC For technical questions please call 1 800 444 3353 Page 5 INSPECTION MAINTENANCE AND CLEANING 1 ZA warnine Make sure the ignition of the vehicle is in the OFF position and that the tool is disconnected from the electrical outlet before performing any inspec tion maintenance or cleaning procedures 2 BEFORE EACH USE inspect the general condition of the tool Check for loose screws misalignment or binding of moving parts cracked or broken parts damaged electrical wiring and any other condition that may affect its safe operation If abnor mal noise or vibration occurs have the problem corrected before further use Do not use damaged equipment PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
3. 12 VOLT OOOGA HORN ASSEMBLY AND OPERATION INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by ie HARBOR FREIGHT WL TOOLS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http Awww harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SPECIFICATIONS Operating Power 12 Volts DC Bell Opening 3 Dia x 4 5 8 L PVC Horns amp metal enclosed motor 110 dB Weight 1 4 Pounds Save This Manual You will need this manual for the safety warnings and precautions assembly oper ating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Write the product s serial number in the back of the manual near the assembly dia gram or write month and year of purchase if product has no number Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY RULES WARNING READ AND UNDERSTAND ALL INSTRUCTIONS F
4. ailure to follow all instructions listed below may result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS WORK AREA 1 Keep your work area clean and well lit Cluttered benches and dark areas invite accidents 2 Keep children and visitors away while installing and operating Distractions can cause you to lose control Never allow children to play with the Oooga Horn 3 Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded 4 Do not expose the Oooga Horn to rain or wet conditions Water entering the Oooga Horn will increase the risk of electric shock 5 Use safety equipment Dust mask nonskid safety shoes or hearing protection must be used for appropriate conditions Always wear ANSI approved safety goggles and a dust mask respirator when installing this item SKU 96291 For technical questions please call 1 800 444 3353 Page 2 10 11 12 Store idle equipment out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users Check for breakage of parts and any other condition that may affect the Oooga Horn s operation If damaged have the tool serviced before using Service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel could result in a risk of injury Maintain labels and name
5. nt the Oooga Horn 1 This location must shelter the Oooga Horn and Compressor from incoming rain road water and mud splash from under the vehicle Do not mount the Horn near hot engine components or where it may come into direct contact with hot surfaces or any moving parts Mount the Oooga Horn to the vehicle s chassis using the Nut and Bolt 2 The Oooga Horn 1 should be pointing forward and slightly down for maximum efficiency A SKU 96291 For technical questions please call 1 800 444 3353 Page 3 hole may need to be drilled in the chassis frame to accomplish this Before drilling the hole make sure the drill s path will not come in contact with hidden wiring or any other obstructions or vehicle components Tighten the Nut securely 4 Mount the Electric Relay not included as shown in the Wiring Diagrams to the chassis frame near the Oooga Horn using a Bolt and Nut not included Tighten securely D Make the connections to the Oooga Horn 1 and the Electric Relay not included as shown on the Mounting and Wiring Diagrams Always use terminal connectors not included on all connections Connect the terminal on the Electric Relay to a 30A fused circuit Note Most vehicles use a negative ground but some vehicles employ a positive ground If this is the case refer to Positive Ground Wiring Diagram Pay attention to polarity Negative Ground Wiring Diagram Electric Relay Pushbutton Horn Switch 7 85
6. plates on the Oooga Horn These carry important infor mation If unreadable or missing contact Harbor Freight Tools for a replacement WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq Exposure to noise levels over 85 dB is hazardous to hearing Always wear ANSI approved hearing protection when operating the Oooga Horn Never use Horn in close proximity to people or animals as the decibel level may cause hear ing damage Before using the Oooga Horn check and comply with local standards for noise pollution levels UNPACKING When unpacking check to make sure that the item is intact and undamaged lf any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible ASSEMBLY INSTRUCTIONS Caution Installation should be completed by a qualified technician 1 Before attempting installation of the Oooga Horn turn off the ignition shift the gear into park for automatic transmissions or reverse for manual Remove the car keys from the ignition switch and allow the engine to cool Place wheel chocks on both sides of at least 2 wheels Disconnect the vehicle s battery Make sure the engine and engine compartment are cool before beginning work Lift the vehicle hood and find a suitable location to mou
Download Pdf Manuals
Related Search