Harbor Freight Tools 1.51 cu. ft. Solid Steel Digital Floor Safe Product manual
Contents
1. Do not allow children to play with or near safe Keep keys and codes away from children 1 Close the door and turn the Handle counterclockwise 2 Turn the Knob counterclockwise 3 Pull on the door to make certain it is properly locked Item 61565 For technical questions please call 1 888 866 5797 5 MASTER CODE a Press O O on the Key Pad and press the Code Reset Button until the Yellow Light on the Front Control Panel lights up b Input your new Code 3 to 8 digits into the Key Pad followed by either the A or B Key c The Safe will beep twice to confirm that the Code has been changed Important If the Safe beeps three times the code has not been accepted Repeat the steps above d Leave the door open until the code has been tested see below 6 With the door still open TEST the new code a First extend the door lock latch to the locked position by turning Handle counterclockwise and then turning Knob clockwise b Once the latch is in the locked position use the new code to open the latch and ensure that it works Note If desired make a note of the new Code and store it in a safe place TaN oN aN AN VN PrN Knob Figure E Closing Handle Page 5 Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician 1 Low battery power warning The red LED light on the keypad will light when the batteries wear down Wh2. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Bunker Hill Security 1 5 cu ft Digital Floor Safe Batteries sold separately To ensure security of your safe Bunker Hill Security does NOT provide replacement keys Visit our website at http www harborfreight com REV 14f Email our technical support at productsupport harborfreight com ITEM 61565 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 888 866 5797 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved 3 No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Overal
3. en you observe the red LED light on immediately replace the batteries 2 Protect the safe from moist or wet conditions This may cause electronic fault in the keypad or corrosion of the steel construction 3 Occasionally wipe the safe and keypad with a soft dry cloth or brush to remove dust 4 Occasionally apply a small amount of light oil or lock lubricant to the mechanical lock mechanism Be careful not to get any oil or other liquids on or near the electronic mechanism 5 Occasionally apply a small amount of oil to the wheel axles 6 Occasionally vacuum or brush dust from the carpet lining of the safe Bunker Hill Security Page 6 For technical questions please call 1 888 866 5797 Item 61565 Replacing the Batteries 1 If the Red Light illuminates the Batteries need to be changed Follow the instructions for opening the Safe The Battery Compartment is located on the inside of the Door Gently slide the Battery Cover off the Battery Compartment Remove used batteries Dispose of them properly or recycle them Insert four new AA Batteries Position batteries in proper polarity and do not install batteries of different types charge levels or capacities together Reinstall battery cover by placing it low against the Battery Compartment and sliding it into place Record Serial Number Here Note If product has no serial number record month and year of purchase instead Item 61565 For techn
4. er the four anchor bolts Because of the heavy weight of the Safe this task should only be done by several capable workmen With the Safe in position add washers and nuts to Anchor Bolts By tightening the nuts in place the sleeve around each bolt will expand and secure each bolt into the concrete to secure the Safe in place Page 3 Operation Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product Opening with Code Note The Safe comes preset with a code of 1 5 9 1 Press the numbers 1 5 9 on the Key Pad then press either the A or B Key Note The Yellow Light will illuminate each time a key is pressed If it does not open the safe with the key see below and replace the batteries see page 7 2 Once the Green light is on a turn the Knob clockwise b turn the Handle clockwise and c pull the Door open Note The Knob and Handle remain unlocked only for several seconds after inputting numbers Note Three wrong entries will sound an alarm and disable the Key Pad for 20 seconds Three additional wrong entries will sound an alarm and disable the Key Pad for 5 minutes To stop the alarm Open the safe with the key and temporarily remove a battery Opening with Key Note The Key is used to open the safe DO NOT STORE KEYS IN SAFE 1 Gently remove the Manual Lock Cover 2 Insert Ke
5. ical questions please call 1 888 866 5797 7 After changing the batteries test the Code and change it as needed before closing the Door Battery Cover Figure F Battery Compartment Note Replacement parts are not available for this item Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the me
6. l Dimensions 22 82 H x 14 17 W x 13 D Capacity 1 5 cubic foot Construction Keypad Features 9 ga steel plate housing 6 ga steel plate door frame 5 ga steel door 0 9 A amp B key code set Green LED code OPEN Red LED code Battery Change Yellow LED code Change Accepted Adjustable shelf Mounting Can be wall mounted Weight 76 5 Ibs IMPORTANT SAFETY INFORMATION Installation Precautions 1 Verify that installation surface has no hidden utility lines before drilling or driving screws 2 Wear ANSI approved safety goggles during installation wo Mount securely before use Install only according to these instructions Improper installation can create hazards 5 Keep installation area clean and well lit Use Precautions 1 Keep closed and locked whenever unattended RISK OF CHILD ENTRAPMENT AND SUFFOCATION Check inside before closing Do not allow children to play with or near safe Keep keys and codes away from children N Keep clear of door when closing ad Position batteries in proper polarity and do not install batteries of different types charge levels or capacities together 4 Use as intended only Page 2 For technical questions please call 1 888 866 5797 Keep bystanders out of the area during installation Do not install when tired or when under the influence of alcohol drugs or medication At least two people are needed to move this prod
7. rchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state Bunker Hill Security 3491 Mission Oaks Blvd e PO Box 6009 Camarillo CA 93011 1 888 866 5797
8. t This safe may be used as a roll about with the included casters or may be bolted to the wall for more permanent installation Wheel Assembly 1 Place the Safe on its side for easy access to the bottom of the Safe 5 Use Anchor Bolts or seek a bonded professional for installation of the Safe into cement Note For floor or wall mounting use bolts of a suitable size not included to bolt into wall studs or floor joists 2 Assemble each wheel using the included wheel axles 6 3 Secure each wheel in place using Cotter Pin Mounting Holes Item 61565 Wheel Cotter Axle Pin The Safe may be bolted to a wall or a floor to deter theft and prevent tipping There are mounting holes in the back wall and bottom of the safe See Figure A below Figure A Rear Mounting Hole Locations For technical questions please call 1 888 866 5797 Using the back of or bottom of the Safe as a template mark the location of the mounting holes on the concrete surface using a pencil or other marker Move the Safe aside and drill four suitable pilot holes in the mounting surface Make certain that the drilling path is clear and free of obstacles such as wires cables and electrical lines Drill holes should be the diameter of the Anchor Bolt sleeves Insert the Anchor Bolts into each drilled hole and tap Bolts into concrete Remove washer and nut from each bolt The Safe now has to be lifted into position to fit ov
9. uct Place the Safe on correct surface Only use this Safe on a stable level clean and dry surface that is capable of sustaining the load Inspect before every use do not use if parts are loose or damaged Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Do not store Keys inside of the Safe Place the emergency keys in a location outside of the safe making sure they are in a secure location that you can find Item 61565 A WARNING The brass components of this product 9 contain lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator 10 The Safe is not fireproof NOTE Harbor Freight Tools is not responsible for the loss of any property stored within this safe due to theft fire or any other circumstance Installation Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this produc
10. y into the lock and turn clockwise Then a turn the Knob clockwise b turn the Handle clockwise and c pull the Door open Page 4 For technical questions please call 1 888 866 5797 Green Light Ready Red Light Low Battery Yellow Light Knob Proceed a A Key B Key a Manual Lock Cover Handle Figure B Key Pad Controls Manual Lock Cover Handle Figure C Manual Lock Item 61565 Changing the Code Note The Safe comes preset with a code of 1 5 9 1 Follow the instructions for opening the Safe to open the door 2 Make sure that the Key is available before changing the code 3 Keep door open during the entire procedure of changing the code On the inside of the Door near the hinge there is the small red Code Reset Button See Figure D Code Reset Button Figure D Code Reset Button 4 USER CODE a Press the Code Reset Button until the Yellow Light on the Front Control Panel lights up b Input your new Code 3 to 8 digits into the Key Pad followed by either the A or B Key c The Safe will beep twice to confirm that the Code has been changed Important If the Safe beeps three times the code has not been accepted Repeat the steps above d Leave the door open until the code has been tested see below Closing AWARNING Keep closed and locked whenever unattended RISK OF CHILD ENTRAPMENT AND SUFFOCATION Check inside before closing
Download Pdf Manuals
Related Search