Hans Grohe 04193XX0 User's Manual
Contents
1. ring retainer nut SS Se pivot tailpiece 0 English link spring clip English Reset the High Temperature Limit Stop optional Use a 4 mm Allen wrench to push the screw 4mm cover into the handle Use the 4mm Allen wrench to loosen the handle screw 4 complete revolutions Remove the handle Remove the nut cover Remove the handle screw from the stem of the cartridge Remove the high temperature limit stop Replace the high temperature limit stop so that the pin on the cartridge is in the desired slot on the limit stop Note the temperatures given in the diagram assume a water heater temperature of 140 F a cold water temperature of 50 F anda water pressure of 45 PSI Replace the nut cover Replace the handle screw Use the Allen wrench to turn the screw 4 revolutions Replace the handle Finish tightening the handle screw Turn on the water and test the faucet Francais Mitigeurs de lavabo Solaris E 04167XX0 Allegro E 04180XX0 Metro E 04193XX0 Solaris E Allegro E Metro E 04167XX0 04180XX0 04193XX0 Donn es techniques Pression d eau recommand e 22 72 psi Temp rature recommand e pour l eau chaude 120 140 F Dimension du trou dans la surface de montage 1 1 4 po Epaisseur maximale de la surface de montage 1 5 8 po D bit 2 2 gpm max Vous devez conna tre et respecter tous les codes de plomberie lo2. Solaris2 E 04167XX0 Allegro E 04180XX0 Metro E 04193XX0 ansgrone English Single Control Lavatory Faucet Solaris E 04167XX0 Allegro E 04180XX0 Metro E 04193XX0 Solaris E 04167XX0 Technical Information Recommended water pressure Recommended hot water temp Max hot water temp Hole size in mounting surface Max mounting surface depth Flow rate M3 Cartridge with high temperature limit stop Allegro E 04180XX0 Metro E 04193XX0 14 7 72 5 psi 120 140 F 165 F 1 1 4 1 5 8 2 2 gpm 3 8 supply hoses requires 3 8 compression fitting not included Please know and follow all applicable local plumbing codes when setting the temperature on the water heater Installation Considerations e For best results Hansgrohe recommends that this unit be installed by a licensed profes sional plumber e Please read over these instructions thoroughly before beginning installation Make sure that you have all tools and supplies needed to complete the installation e The high temperature limit stop may be reset if desired English Installation Place the faucet and sealing gasket on the mount ing surface Slide the washer over the bolt Install the collar Tighten the collar with a flat head screwdriver Secure the supply hoses to the stops with 3 8 compression fittings not included Use two wrenches as shown to keep the A hoses
3. e limite d eau chaude Remettez en place la but e limite d eau chaude de sorte que l onglet de la cartouche soit dans la fente voulue de la but e Les temp ratures indiqu es sur le sch ma pr supposent que la tem p rature du chauffe eau est r gl e 140 F pour l eau chaude et 50 F pour l eau froide raison d une pression d arriv e d eau de 45 psi ee DERE Remettez le cache crou en place R installez la vis de la poign e Serrez la vis 4 tours complets Remettez la poign e en place Serrez la vis Installez le cache vis Ouvrez l eau et v rifiez le robinet Replacement Parts 7 CS SES _ EX N nut cover nut cartridge 92730000 fixing set 96016000 aerator 13085XX0 pull rod 96657XX0 handle Solaris handle Allegro handle Metro screw cover 88655000 pop up drain 88509XX0 O NN O ND XX color 00 chrome 82 brushed nickel 83 polished nickel Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets kitchen faucets and showers consist of very different materials to comply with the needs of the market with regard to design and functionality To avoid damage and returns it is necessary to consider certain criteria when cleaning Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime however please pay attention to the follow
4. cessaire e Utilisez la quote de produit nettoyant et respectez la dur e recommand e par le fabricant Ne laissez pas le produit sur les articles de robinetterie plus longtemps que n cessaire e Un nettoyage r gulier peut pr venir la formation de d p ts calcaires e Si vous utilisez des nettoyants en vaporisateur vaporisez d abord sur une ponge ou un chiffon Ne vaporisez jamais directement sur un robinet des gouttelettes pourraient s infiltrer dans les ouvertures et les interstices et endommager celui ci e Apr s le nettoyage rincez abondamment avec de l eau propre pour liminer tout r sidu de produit nettoyant Important Les r sidus de savon liquide de shampoing et de mousse pour la douche peuvent galement endommager la robinette rie rincez donc avec de l eau propre apr s utilisation de ces produits Veuillez noter si la surface est d j endommag e les produits de nettoyage l endommageront encore plus Les composants dont la surface est endommag e devraient tre remplac s sous peine d entrainer des blessures Les dommages dus un mauvais traitement ne sont pas couverts par la garantie Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe Inc Hansgrohe This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1 1996 and installed in either the United States or
5. ing points when cleaning faucets and showers e Only use cleaning materials which are explicitly intended for this type of application e Never use cleaning materials which contain hydrochloric formic phosphoric or acetic acid as they cause considerable damage e Never mix one cleaning material with another e Never use cleaning materials or appliances with an abrasive effect such as unsuitable cleaning powders sponge pads or micro fiber cloths Cleaning Instructions for Faucets and Showers Please follow the cleaning material manufacturer s instructions In addition pay attention to the following points e Clean the faucets and showers as and when required e _ Use the amount of cleaning product and the amount of time recommended by the manufacturer Do not leave the cleaner on the fixture longer than necessary e Regular cleaning can prevent calcification e When using spray cleaners spray first onto a soft cloth or sponge Never spray directly onto the faucet as drop lets can enter openings and gaps and cause damage e After cleaning rinse thoroughly with clean water to remove any cleaner residue Important Residues of liquid soaps shampoos and shower foams can also cause damage so rinse with clean water after using Please note if the surface is already damaged the effect of cleaning materials will cause further damage Components with damaged surfaces must be replaced or injury could result Damage caused by improp
6. Canada WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only This warranty is non transferable WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manufactured product Hansgrohe warrants this product against defects in material or workmanship as follows Hansgrohe will repair at no charge for parts only or at its option replace any product or part of the product that proves defective because of improper workmanship and or material under normal installation use service and maintenance If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made Hansgrohe may elect to refund the purchase price in exchange for the return of the product LENGTH OF WARRANTY Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences If you are a consumer who purchased the product for use primarily for personal family or household purposes this warranty extends for as long as you own the product and the home in which the product is originally installed If you purchased the product for use primarily for any other purpose including without limitation a commer cial purpose this warranty extends only i for 1 year with respect to Hansgrohe and Commercial products and ii for 5 years with respect to AXOR products THIS WARRANTY DOES NOT COVER AND HANSGROHE WILL NOT PAY FOR A Conditi
7. Ne serrez pas compl te ment l crou Installez le raccord en T et la queue Au besoin tournez l obturateur de fa on ce que le pivot soit face au robinet Serrez l crou de retenue Mettez le plongeur dans l obturateur Installez les joints sph riques sur la tige horizontale un de chaque c t de l crou sph rique Poussez la tige horizontale dans le pivot Serrez l crou Faites glisser la tringle sur l extr mit de la tige d entrainement Serrez la vis Glissez la tringle sur la tige horizon tale V rifiez le mouvement de la tige d entra nement et du butoir Repositionnez la tringle si n cessaire La tringle comporte plusieurs ouvertures la tige horizontale peut tre ins r e dans l une d entre elle au choix Si le mouvement de l obturateur semble ad quat faites glisser la pince ressort sur l extr mit de la tige horizontale 10 plongeur Z collerette tringle joint d tanch it o joint mack S pince 9 anneau de lo friction QI o crou de retenue O g i tige hori zontale pivot T N joint spherique Francais R glage de la but e limite d eau chaude en option Poussez le cache vis dans la poign e l aide d une cl hexagonale de 4 mm Desserrez la vis de la poign e 4 tours complets Enlevez la poign e et retirez le cache vis Enlevez le cache crou Retirez la vis de la poign e Enlevez la but
8. caux applicables pour le r glage de la temp rature du chauffe eau A prendre en consid ration pour l installation e Les tuyaux d arriv e flexibles requi rent des but es d arr t avec des raccords compres sion de 3 8 po non compris e Le robinet comprend la but e limite d eau chaude en position maximum Ce r glage peut tre modifi si d sir e Pour obtenir les meilleurs r sultats Hansgrohe recommande de confier l installation un plombier professionnel certifi Francais Installation Placez le robinet et le joint d tanch it sur la surface de montage Installez la rondelle et le collier de montage Serrez le collier de montage Installez les tuyaux d arriv e flexibles sur les bu t es d arr t avec des raccords compression de 3 8 po non compris Utilisez deux cl s tel qu illustr dans le sch ma pour viter que les tuyaux ne s entortillent Installez le tirette Installez l obturateur clapet Reprogrammez la but e limite d eau chaude en option Fran ais Francais Installation de l obturateur clapet Retirez le plongeur D vissez la collerette du raccord en T D vissez la queue du raccord en T Enrobez les filets de ruban T flon et remettez en place Installez le joint d tanch it sur la col lerette Installez les dans l vier Par le dessous installez le joint mack l anneau de friction et l crou de retenue sur la collerette
9. er treatment is not covered under the warranty Recommandations pour le nettoyage des produits Hansgrohe Les robinetteries modernes de lavabo de cuisine et de douche utilisent des mat riaux tr s diff rents pour r pondre aux besoins du march en termes de conception et de fonctionnalit Certaines r gles de base doivent tre respect es lors du nettoyage de ces produits afin d viter de les endommager ou d avoir les retourner Produits de nettoyage pour robinetteries et douches Les acides sont une partie int grante n cessaire de tous les produits de d tartrage il faut cependant prendre les pr cautions suivantes lors du nettoyage des robinets et des douches e N utilisez que des produits articles de nettoyage con us sp cifiquement pour les articles de robinetterie et de douche e N utilisez jamais de produits articles de nettoyage contenant de l acide chlorhydrique formique phosphorique ou ac tique car ils pourraient causer des dommages consid rables e Ne m langez jamais deux produits de nettoyage e N utilisez jamais de produits articles de nettoyage de nature abrasive tels que poudres de nettoyage tampons ponge ou chiffons microfibre non appropri s 13 Instructions de nettoyage pour robinetteries et douches Veuillez suivre les instructions du fabricant de produits articles de nettoyage De plus tenez compte des conseils suivants Nettoyez vos produits de robinetterie et de douche aussi souvent que n
10. from twisting English Install the pull rod Install the drain Reset the high temperature limit stop optional Install the pop up drain Remove the plunger assembly Unscrew the drain outlet flange from the tee Wrap the threads with Teflon tape Unscrew the tailpiece from the tee and replace Install the flexible sealing gasket on the flange Sit it in the sink outlet From below install the black mack gasket white friction ring and retainer nut to the flange Do not tighten the nut against the bottom of the sink at this time Thread the tee and tailpiece to the flange The pivot must face the faucet If neces sary turn the drain assembly Tighten the retainer nut Sit the plunger assembly in the drain Install the horizontal rod through the pivot ball seals and into the tee so that the end goes through the loop in the bottom of the height adjuster The two pivot ball seals should surround the pivot ball Slide the link over end of pull rod Tighten screw Slide one end of spring clip over end of horizontal rod Slide link over end of hori zontal rod Test motion of drain plunger Reposition link as necessary There are multiple holes in the link the horizontal rod may go through any of the holes When satisfied with the action of the drain slide the other end of the spring clip over the end of the horizontal rod plunger Z flange O gasket mack gasket o
11. ons malfunctions or damage not resulting from defects in material or workmanship B Conditions malfunctions or damage resulting from 1 normal wear and tear improper installation improper maintenance misuse abuse negligence accident or alteration or 2 the use of abrasive or caustic cleaning agents or no rinse cleaning products or the use of the product in any manner contrary to the product instruc tions 3 Conditions in the home such as excessive water pressure or corrosion C Labor or other expenses for the disconnection deinstallation or return of the product for warranty service or for installation or reinstallation of the product including but not limited to proper packaging and shipping costs or for installation or reinstallation of the product 14 D Accessories connected materials and products or related products not manufactured by Hansgrohe TO OBTAIN WARRANTY PARTS OR INFORMATION Contact your Hansgrohe retailer or contact Technical Service at Hansgrohe Inc 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Toll free 800 334 0455 In requesting warranty service you will need to provide 1 The sales receipt or other evidence of the date and place of purchase 2 A description of the problem 3 Delivery of the product or the defective part postage prepaid and carefully packed and insured to Hansgrohe Inc 1492 Bluegrass Lakes Parkway Alpharetta Georgia 30004 Attention Technical Service if re
12. quired by Hansgrohe When warranty service is completed any repaired or replacement product or part will be returned to you postage prepaid EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT OR IN LIMITED CIRCUMSTANCES REFUND OF THE PURCHASE PRICE AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY INCLUDING MERCHANTABILITY Some States do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from State to State You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson Moss Warranty Act PRODUCT INSTRUCTIONS AND QUESTIONS Upon purchase or prior to installation please carefully inspect your Hansgrohe product for any damage or visible defect Prior to installing always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product If you have questions at any time about the use ins
13. tallation or performance of your Hansgrohe product or this warranty please call or write to us or call us toll free at 800 334 0455 ansgrohe Hansgrohe Inc 1490 Bluegrass Lakes Parkway Alpharetta GA 30004 Tel 770 360 9880 Fax 770 360 9887 www hansgrohe usa com US Installation Instructions Part No 90445401 01 Revised 03 2008
Download Pdf Manuals
Related Search