Haier HWM80-68B User's Manual
Contents
1. filter from the document bag install it tothe filter cover of inner tub See to the figure Inner fub Lint filter How to change the direction of the drain hose 1 Dismount the back cover of the washing machine 4 Dismount the protecting cover of the drain outlet at the 2 Lay down the washing machine gently with the front other side as indicated in Figure 3 side facing the ground Use cross screwdriver to 5 Extend the drain hose out of the other side Fix the drain loosen the eight screws Take off the bottomplate bottom plate hose onto the cabinet with the drain hose rack Set the drain hose nuton and fasten the nut to the direction indicated in the figure as per Figure 4 drain outlet soft item protecting 3 Put down the outer drain hose Twist the drain hose nut counterclockwise to take it off asindicated in Figure 1 Figure 3 Take off the drain hose rack Put the drain hose into 6 Install the protecting cover of the drain outlet to the other the cabinet as indicated in Figure 2 drain hose Drain hose nut Drain h Figure 1 Figure 2 The drain hose shall drain smoothly 1 The height of the drain hose shall be less than 10cm or the drainage will not be smooth and cost such long time that the machine may stop at mid way 2 Do not ramp or press the drain hose 3 If the drain hose is too long cut it at mid point Tomake smooth drainage cut the front end of the hose slantingly rack d2. can make it easier to remove the soil For those laundries that may get lint ball and those with long fur tum it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly 2 Put in the laundries The capacity of washing and spinning of he machine refer to the largest weight ofthe standard laundries under dry conditionthat can be washed or spinned in one time One time washing quantity shall be lower than the rated capacity The thickness size type of the cloth will influence the actual washing capacity It is suitable for one time washing to put inreasonable amount of laundries and the laundries can be turned round in washing Please do notselect high waterlevel for laundriesless than 2 5kg toavoid splashing In washing the fluffy laun dries like the woolen blanket the quantity shall notexce ed 3kg foreach cycle In using waterwith high temperature please pay atten tion to the washing temperature limitstated on the label of the laundries Inlet for concentrated washing A powder and detergent Put the washing powder and softener into the detergent ee box directly as indicated in the left figure g After that please close the detergent box Refer to the following table for the usage of the detergent The standard dosage ofthe detergent and the water Softener inlet quantity How to use the washing powder Direct dissolved in the machine De
3. can work in cooperation with automatic programs like standard and heavy There is intermittent pulsator stirring during soak 4 Push the WATER LEVEL button to select suitable water level T select other water level push the WATER LEVEL button to set the water level 5 Push the RESERVE button to select suitable reserve wash program After the poweris switched on the reserve programis set tooff mode automatically Ifyou need toset the washing procedure tobe finished atreserved time please push the RESERVE button toset the reserve wash program Referto RESERVE BUTTON in Page 10 forselection Reserve time from 2 to 24 hours Confirm the operation of reserve program The washing will be finished after 18 hours START PAUS ee When the RESERVE function is activated the indicator of the program you have set will be off The RESERVE HOUR and TIME REMAIN indicators will be on During reserve procedure you can push the RESERVE button to display the reserve mode To change the running program or cancel the reserve setting you need to switch off the power and make new selection 6 Push the START PAUSE button 5 Close the top lid 6 Finish washing 13 Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Please take off the
4. draintime Acertain period is needed before it starts spinning The pulsator pauses during water filling in washing and rinsing It is toavoid splashing during water filling There may be some water flowing out ofthe drain hose in the first use of the machine It is the water remained inthe machine during the ex factory performance inspection e In adding water the pulsator performs stirring slightly It is tosoak the laundries more completely 14 Trouble shooting If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomenan The drainage cannot work or is too slow The digitron displays E1 and it rings The reason ls the drain hose blocked by foreign material How to settle Clean the foreign material Push the start button again After washing and rinsing it stops running during spinning The digitron displays E2 and it rings The top lidis not closed Close the toplid The safety switch acts and the prong cannot work after twice automatic imbalance revising The digitron displays E3 and it rings Are the laundries put slantingly e Is the machine slanting Reorder the laundrie
5. horizontal BALANCE DISPLAY WATER LEVEL button The machine is setted to be water level 4 when the light is on you press the button continuously you will select the water level 4 5 6 7 8 1 2 3 in turn except quick wash program In the process of SOAK WASH RINSE the water level is no changed then it only supply water When you selected the quick wash the water level is setted to be 2 then it can not be hanged the water level 10 SECC FLASH LIGHT SURPLUS MIN 8 4 C S i lt WM850A 6 2 sf SS DAD 5 1 RESERVE HOURS LATEF WATER RESERVE LEVEL L bel L RESERVE button Push the buttonto select washingfinishing time between 2 24 hours When the RESERVE function is activated the RESERVE andTIME REMAIN indicators are on Theother indicators are off Push the RESERVE button to display the reserve mode START PAUSE button After the poweris switched on push it tostart Digitron the machine sseeeq During working pushit to pause working During pause pushit to resume working During operation of programs it displays the remained time minute During reserve procedure it displays the remained reserve time in hour Incase of abnormal phenomenon it displays the abnormal symbol see to Page 15 POWER ON OFF button Push the On Offbutton to switchon the power When the poweris on pushit again toswitch off the power Meese eee S
6. the top lid There s abnormal sound inside the machine Is the machine slanting Are the laundries slanting in spinning Level the machine properly Re order the laundries The water faucet leaks Is the jointer screw of the water inlet hose is loose or twisted awry Fasten the jointer screw properly No water inlet 15 s the power plug plugged tightly s the water faucet opened Are the POWER ON OFF and START PAUSE buttons pushed down Plug the power plug tightly Open the water faucet Push the power ON OFF button and START PAUSE button Packing list A Name Quantity k User s manual One piece e The end connecting to the washing machine Jointer connecting the water inlet hose to the water faucet One piece The end connecting to the water inlet hose jointer One piece gt Tapping screws 7 Eight pieces A g Lint filter i One piece Full automatic One set washing machine wy Specification gt Water level Water quantity about 1 21L 2 28L 3 35L 4 41L 5 47L 6 53L 7 58L 8 65L Injection pressure 0 03MPa 0 78MPa J 16
7. Full automatic washing machine User s manual This manual is for HWM80 68B e Please read this manual carefully before using e Retain it for future reference Contents 2 Names of the parts Le ee ee ee ee ee ee ee ee ee N Safety precautions 2 cece eee eee eee 2 Installation and adjustment seeeeeeeeee 4 e Usage of the drainhose ssssssesennnnee 5 Installation the water inlet hose 6 Preparation before washing tttttttts 8 Putin the laundries 22 2222s seen eee 9 Add the detergent and softener ttr 9 Use the operation knobs and buttons gt 10 Close the top lid se ee 13 Finish washing 2 0 e eee eee eee 13 Disposal after washing settrtereeeees 14 Answers to question esse eee e eee eee anes 14 Trouble shooting Pee ere ee ere ee ee ere ere eee ere ee 15 eis list SPeciiCMOlisx nsencnenwnn ewan oy Names of the parts Cool water valve Globe cover Back faceplate control pans Power line ri Cabinet handle Ul Level met ihnertib P Lint fiter Installed by user Filter cove A hanging hole i LN Ay 9 for the drain Drain hose Control pane S S hose fil bal back cove Front contro Front fixed board Adjustable foot foot Pulsator seam Cabinet Adjustable foot Rear fixed foot Meaning and description of the symbols Contents marked with that symbol are related Warning s
8. IN Refer to PROCEDURE SELECTION METHOD tomake selection Attention Even there s no water inthe tub a certain period is required before spin starting Do not use the SOAK program for the woolen textiles Separate the laundries that are not colorfast from other laundries in washing 12 Procedure selection method Times of pushing the SELECT button Selected procedure Applicable circumstance Contents the lightedindicators indicate the programs about to run WASH SPIN When the common laundriesneed washing rinsing and spinning GOAK WASH RINSE SPIN WASH the washing liquid remains in the tub Repeat using the washing liquid GOAK wash CRINSE SPIN WASH RINSE the rinsing liquid remains in the tub When prevent thelaundries from corrugating and thelaundries do not need spinning SOAK WASH CRINSE SPIND RINSE SPIN When the laundries need SOAK WASH RINSE SPIN SPIN spin after drain When the laundries need only spinning after manual washing first drain then spin SOAK WASH NSD CEPIN SOAK SPIN The laundries are very dirty or the sleeves and collarsof the shirtare very dirty First soak thenwash SOAK WASH RINSE SPIN Push the SELECT button for 6 times and it will resume the initial mode It will circulate in that sequence The SOAK procedure
9. arpet The ventilation holes at the bottom 9 Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning X S Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more Fo Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc The handicapped or children without care shall not use the machine Toprevent the lintin the tubfrom blocking the cascade outlet and influencing the cascade effect please keep the lint filter in good condition and install itto proper position during washing If the lintfilter is lost or damaged please contact the local after sale service department of our company a N Keep the machine away from direct sunlight and heat source like the heater To protect your laundries and wash ing machine please take out all of the coins buttons sand hairpin and other foreign materials before washing S Please check if the water fau
10. cet is open and if the connection of the water inlet pipe is proper e tis suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the bottom plate After opening the package pleaselean the washing machine gently down on soft items like towel cloth blanket etc Install the bottom plate to the bottom of the machine with eight screws by a cross screwdriver then lift the machine up gently See to the figure Bottom plate p Screw Soft items The largest allowable slope of the shank base of the machine is 2 The slantingor roughground will result in unstable running or stoppage ofthe machine Please adjust it with following methods lt 2 Confirm it s horizontal If the bulb of the level meter at the balance display position is inside the standard circle it indicates that the machine is horizontal Otherwise you need to adjust the adjustable leg of the machine Suitable Not suitable Adjustthe adjustable leg Standard circle Air bubble 1 To twistthe adjustable leg please first lift up the leg side slightly loosen the adjustable nut and then twist the leg 2 After adjustment fasten the nut Adjustable nut Adjustable leg Install the lint filter After opening the package please take out thelint wee
11. detergent box and wash it with water 1 How to take it off Pull it upwards slantingly and gently 2 How to install Put it in from the top slantingly Dismount Install The lint filter must be used during washing It must be cleaned in time after each using Lint filter 1 Pull it up to dismantle 2 Push it down to install 3 Clean the filter screen after washing Gitte Dismantle Clean The filter screen of the water inlet valve is likely to be blocked by foreign materials and influence the water inlet Please clean it with brush every two months If the cabinet is dirty wipe it with wet cloth Do not flush it directly with water Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 Do not store water in the washing machine for a long period Drain the water completely after each using 3 Be sure to pull off the power plug before maintenance 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid Answers to question Common phenomena Phenomena Explanation e The spinning isintermittent when itstarts It is tobalance the laundries to avoid slanting Push the SPIN button but it doesn t act The program issetting the
12. ee n HOHTSERpLusqu CODMORM conc RAA 7 3 HEAVY WASH amp 5 POWER 6 2 GENTLE RINSE i ON OFF 5 1 RESERVE HOURS LATER a on es STAR vol RESERVE PROGRAM SELECT pueg anannannnnnnnnna SELECT button Push it to select one or more programs from SOAK WASH RINSE and SPIN PROGRAM button The following fourprograms are available for your option Standard Common washing Heavy Washing the heavy clothes Gentle Washing the woolen textiles or underwear Fast 10 minute quick washing of laundries with light soil Remarks Push the On Off button to switch on the power If the washing machine is idle for 5 minutes it will automatically switch off the power 11 b Steps of using the operation buttons and description of each step 1 Push the POWER ON OFF button to switch on the power 2E 2 Push the program button to select suitable automatic program After switching on the power the machine will set standard program automatically To select other automatic program push the PROGRAM button till the relative indcator is on For instance select FAST program for laundries wth small quantity and light soil T 3 Push the select button to select suitable procedure ET After switching on the power the washing machine will setto WASH SPIN procedure automatically Itis the common procedure To select other procedures push the SELECT button to select one ormore procedures fromSOAK WASH RINSE and SP
13. ign to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damageof the machine or injure the personal safety of the user Forbidding sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety ofthe user Please check if the power receptacle has good earthing condition before using to guarantee your safety Safety precautions Please insert the power cord into special receptacle with rated vol tage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector When the machine is normally using please put the power plug at the location easily to be insert ed and extracted by hand Be sure to pull the plug off when there s power failure or the machine is being moved cleaned or when it is idle If the power cord is bad to avoid risk it is required to replace it by the technicians of our special shop or the after sale service department Keep the pin of the power plug clean Do not put the machine at damp place like the bathroom Never wash it with water Do not place wet laundries on the control panel In case the washing machine is in stalled on ground with carpet do not block the ventilation hole with c
14. late Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet See to Figure 5 Remark Before installation the threading is 4mm above the upper surface of the nut After installation the threading is 2mm above the upper surface of the nut About 4mm after twisting 1 Do not takeoff the waterabsorption cushion Pleasecheck if the cushion isdropped or damaged eachtime before using Water inlet If it happens so please duly contact ourafter sale service hose nut department 2 Set the nutof the water inlethose on the waterinlet valve jointer 3 Fasten the nut Swing it gently toconfirm if it s fastenedwell Water inlet valvejointer Water absorption cushion Connection between the water inlet hose jointer and the water inlet hose 1 Push downthe slider Plug the waterinlet hose into the jointer The water inlet 2 Hang thelock lever onto the jointer Release hose jointer the slider tilla click soundis heard Locking level Check the connection between the water inlet hose jointer and the water faucet 1 Swing the hose gently to checkif it is fastened stably 2 After installation open thefaucet to check ifit leaks water 3 Do not bend thehose by force 4 Each time before using please check if theconnection between the water inlethose jointer and thewater faucet f and the installation ofthe water inlet hoseisfirm so as K to avoid dropping owingto improper installati
15. on Dismount the water inlet hose 1 Close the water faucet 2 Press thelock lever and push down theslider Thenpull off the water inlet hose If the machineis used more than once every week the waterinlet hose jointercan remain onthe faucet to avoid damaging thefastening screws 1 Preparation before washing Preparation before washing 1 Connect the water inlet hose Open Check if the laundries pocket Take has special the water faucet 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle The earth terminal shall not link to gas pipeline and faucet water pipeline 3 Put down the drain hose Clear the Tie the long strips fasten out the coins the buttons sand hairpins close zippers etc LA The quantity of the laundries shall not be too large Stretch and loosen the laundries before putting themin the tub 2 is running buttons of the laundries may cause noise For the sake of discretion please put the laundries with buttons into other laundries X Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other laundries Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which
16. rain hose nut side as indicated in Figure 5 Figure 5 7 Install the bottom plate method the same as stated above Lift up the washing machine gently 4 lf extra drain hose is needed please make separate purchase The inner diameter of the extra hose shall not less than 30mm and the length shall not exceed 1 5m gt 30mm If the extra hose is too long cut it either at point AorB 1 Install the water inlet hose Install the water inlet pipe Water faucet suitable water faucet not suitable A gi iF It is required that the front end shall be longer than 10mm The outlet end surface of the faucet shall be flat and smooth If not please file it smooth to avoid leakage Connection between the water inlet hose jointer and the water faucet 1 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 2 Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed Then set the water inlet hose jointer on the faucet See to Figure 2 If the faucet is too large and the jointer cannot be set on please loosen the four screws and take out the bush inside the jointer See to Figure 3 Water inlet hose jointer Slider Screw knife Bushing Sg Water inlet hose Figure 1 Figure 2 Figure 3 3 Fasten the four screws ofthe water inlethose jointer evenly See to Figure 4 4 Take off the namep
17. s Close the top lid Set the washing machine horizontally and then open and close the top lid once The water inlet does nd work or is too slow cannot reach the water level after about 30 minutes The digitron displays E4 and it rings Is the water faucet opened or is there water supply failure s the waterinlet valve blocked Open the water faucet Push the Start Pause button again Clean the water inlet valve then push tha Start Pause button again When you selected the function of re s verve you opened the cover that time the digital tube displays E0 In the processof function of reserve openedthe cover Closing the cover The water level sensor is abnormal that time the digital tube displays E6 The terminal of water level sensor loosing Fix the water level sonor again The cascade currentis poor or there s no cascade current Is there foreign material blocking the spray outlet Clear the foreign material No wash The machine does Is there power failure Is the power plug loose f water level reach the appoint level Use it when the power is on insert the power plug tightly Affusion to appoint level not act No spin Is the power plug loose s the top lid is not closed e Are the laundries put slantingly Insert the power plug tightly Close the top lid Re order the laundries Close
18. terg nt jox 1 Fill in small quantity of water Select water level 1 2 Add the powder Run for 30 seconds to i dissolve it completely How to use the whitener 3 Put in the laundries Select suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 C and a container 2 Add the powder into the container while stirring to fully dissolve it The powderis more prone to pollute the laundries than the detergent Therefore please use it with proper quantity It is suggested not to use high sudsing detergent Washing powder with poor quality or long time storage may be caked Please pay attention to cleaning the detergent box in time Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolve it before use 4 Use the operation knobs and buttons a Description of the function of the operation buttons Mode and meaning of the indicator Flash indicating the running mode On indicating the mode about to run se Flash rapidly indicating abnormal situation Balance display ifthe bulb of the level meter is inside the standard circle tindicates that the machine is
Download Pdf Manuals
Related Search