Haier HWM55-13S User's Manual
Contents
1. Safety precautions Do not stretch hands into the working machine lt is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc Handicapped or children without care shall not use the machine 9 To protect your laundries and wash ing machine please take out all ofthe coins buttons sand hairpin and other foreign materials before washing Keep the machine away from direct sunlight and heat source like the 9 Please check if the water faucet is open and if the connection ofthe water inlet pipe is proper e itis suggested to use foamless washing powder R o _ Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Quick water filling entrance If you do not need spraying spin you can fill water into the wash tub directly through water inlet hose this entrance It can reduce the humidity inside the control panel significantly and prolong the operating life of the components in eee penne Control handle lt L Quick water filling entrance Quick water filling entrance Install the lint2. Do not wash it directly by water Water level djusting lever Corrugation Pipe gt Figure 1 Figure 2 nit e After washing dismount the water inlet hose Do not store water in the tub for long period Discharge the water immediately after each using 9 Pull off the power plug and hang up the power cord Hang up the drain hose Wipe off the water drops on the surface and inside the tub with clean soft cloth Open the cover of the wash tub and the inner outer cover of the spin tub for some time about one hour then close them 13 14 Trouble shooting Answer to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub please take them out immediately 1 Dismantle As indicated in the figure push the point marked with gt lt to pull the spin tub frame to oblique Spin tub frame upwards to dismantle it 2 Install After install the back edge of the spin tub frame to proper position push the four points marked with X by force to reset it Please check carefully The laundries may fall to the lower part Spin tu of the outer side of the spin tub as indicated in the figure If the laundries fall to the outer side of the spin tub during spinning the draining will get blocked and the rotation speed f th in tub is reduced of the spin tub is reduce Laundries When the remained water is frozen Prevent t
3. filter After opening the package please take out the lint filter from the document bag install it to the overflow filter of the wash tub See to the figure Lint filter Usage of the drain hose The drainage shall be smooth with the drain hose 1 The height of the drain hose shall be less than Gg 10cm or the drainage willnot be smooth enough M T and cause incomplete drainage 2 Do not tramp or press the drain hose 3 If the drain hose is too long cut it at mid point To make smooth drainage cut the front end of the hose slantingly 4 lf extra drain hose is needed please make separate purchase The inner diameter of the extra hose shall not less than 30mm and the length shall not exceed 1 5m If the extra hose is too long cut it either at point Aor B How to change the direction of the drain hoses e Figure 1 indicates the leave factory installation position of the drain hose Soft item Extend the drain hose from the side of wash tub Put soft items on the ground Lean the machine down gently with the front surface facing the ground Take off the drain hose from the cabinet Soft item Take the hose out of the fixing groove See to Figure 2 Embed the drain hose into the groove along the side Figure 2 of the wash tub in the order of 1 2 heading for the side of the wash tub See to Figure 3 Extend to the Embed the drain hose into the groove with ay W wa
4. 9 The thickness size type of the cloth will influ ence the actual washing capacity Itis suit able to put in reasonable amount of laundries and the laundries can be turned round in wash ing for one time washing 9 Do not select Maximum water level for laundries less than 2 4kg so as to avoid splashing of water e It is suggested not to use high sudsing detergent Usage of the detergent How to use the whitener How to use the washing powder Direct dissolved in the machine 1 Fill small quantity of water 2 Add the powder Run for 30 seconds to dissolve it completely e Avoid using whitener on laun 3 Put it in the laundries Select suitable dries with color or pattern as they water level are prone to lose color Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub The instant dissolving of the washing The whitener shall not touch powder the laundries directly 1 Prepare warm water of 30 C and a Refer to the user s manual for container l o the usage and quantity of the 2 Add the powder while stirring to fully whitener dissolve it The powder is more prone to pollute the laundries than the detergent Therefore please use it with proper quantity Dosage of different washing powder is different Please refer to the instruction of the washing powder for the detail dosage e r For powder whitener please dissolve it before using Wash
5. Twin tub Washing Machine User s manual This manual is for HWM55 13S e Please read this manual carefully before using Retain it for future reference Contents Vene of the parts Usage of the detergent Disposal after washing Ne Packing list Specification Safety precautions e Installation and adjustment esee 9 Preparation before washing The musts in washing Washing sequence e Trouble shooting Answer to question Names of the parts Buzzer Water filling entrance Water inlet selector handle Wash selector Wash timer Control panel Overflow filter Wash water filling entrance Water level adjusting lever Lint filter Pulsator Wash tub Base frame Drain hose Wash tub cover Outer cover of the spin tub Inner cover of the spin tub Spin timer Spin tub frame Spin tub Meaning and description of the symbols Warning sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Forbidding sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user Please check i
6. e 4 WASH TIMER sTRONG Ex STANDARI 1 i WASH SELECTOR Figure 5 Midway spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Spin 1 Put the gland in properly Please put in the gland properly even if the laundries quantity is small Push Gland oh Bb Proper The laundries Proper No gland are slanting 2 Close the inner and outer cover of the spin tub Outer cover of The spin tub Inner cover of The spin tub 3 Spin for 1 2 minutes 3 Run the foam removing spinning 1 Open the outer cover of the spin tub 2 Set the water filling selector control WASHI SPIN WATER INLET SELE rod at the SPIN side Fill water for about 1 minute If the water quantity filled is too large the water may flow out from the wash tub side Please twist the water tap to limit the water filling 3 Close the outer cover of the spin tub Spin for 1 2 minutes Rinsing Rinse with water filling 1 Put the laundries into the wash tub Select suitable current according to the laundries If you find water flo wing out here please 2 Adjust the water level twist the water tap to Set the water level with water level adjusting limit the water filling lever according to the laundries quantity ww Then fill suitable water continuously 3 Rinse Adjust the wash timer to 5 7 minutes to do rinsing Repeat the midway spinning and Rinse with stored water rinsing with stored water for 2 3
7. eaned in time after each using 1 Take off the lint filter Put hand at the indicated position Push down to take it off See to Figure 1 2 Clean the lint Put it in water and clean while it is still wet See to Figure 2 3 Install the lint filter After cleaning insert the bottom Figure 2 of the lint filter marked with down side into the overflow filter then push the upper part of the filter in marked with up side See to Figure 3 Figure 3 Cleaning the overflow filter Too much lint on the overflow filter will influence the normal usage of the machine Please clean it every two months 1 Take off the overflow filter Flastic fixing claw As indicated in the figure nip the elastic fixing claw and pull it to the direction of the arrow to take it off 12 Cleaning the overflow filter Take off the corrugation pipe Dismantle the upper part of the corrugation pipe inside the overflow filter as indicated in Figure 1 Cleaning the overflow filter Clean the lint around the filter and flush with tap water Install the overflow filter 1 Install the corrugation pipe 2 Insert the mounting plate at the bottom of the filter into the valve cover 3 Hang up the hook at the left upper side 4 Push the upper part in as indicated in Figure 2 Disposal of the complete u Wipe the complete unit with soft cloth twisted dry Wipe with neutral detergent if too dirty
8. f the power receptacle has good earthing condition before using to guarantee your safety Safety precautions Please insert the power cord into special receptacle with rated vol tage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector When the machine is normally using please put the power plug at the location easily to be insert ed and extracted by hand Be sure to pull the plug off when there s power failure or the machine is being moved cleaned or when it is idle If the power cord is bad to avoid risk it is required to replace it by the technicians of our special shop or the after sale service department Keep the pin of the power plug clean Do not put the machine at damp place like the bathroom Never wash it with water Do not place wet laundries on the control panel Do not use water hotter than 50 C In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning A 9 H o Ventilation hole at he bottom of the washing machine NS Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more
9. he freezing be sure to discharge the water completely after using After complete draining set the WASH SELECTOR at STRONG or STANDARD If itis set at DRAIN it will be rather difficult for the frozen water to melt When the water is frozen Pour hot water below 50 C into the wash tub to soak it completely Then turn the pulsator with hands gently Please confirm the drainage can work normally before next using If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomena The reason Is there power failure The machine does Is the power plug loose not act Is the pulsator twisted by foreign materials Is the drain hose put down There s abnormal Is the drain hose frozen sound during washing Is the drain hose blocked by foreign material Are there laundries falling to the outer side of the spin tub There s abnormal soundduring washing Are there hair pin coins or metal items brought inside the tub There s abnormal s the machine slanting sound and violent s the gland pressed evenly vibration during Are there laundries falling to the outer side of Spinning the spin tub Are the laundries in spi
10. ing sequence Overfilling sign Wash timer Wash selector Water filling entrance To set to below 2 minute Standard current irst set to 6 minute then strong current turn it back it can increase the service life of the timer STRONG OFI T woot CN STANDARD Mix DRAIN NA m set orron LINEN WASH SELECTOR WASH TIMER Wash 1 Water inlet selector 1 Set the water inlet selector at the WASH side Figure 1 2 Set the water level adjusting lever to needed line 2 Fill the water and add the dissolved washing powder to make the water level reach the preset position Figure 2 Run washing program for some time to stir and dissolve the powder completely 3 Put in the laundries If the water quantity is insufficient please add water 4 Select the current Select the strength of the current according to the laundries Figure 3 5 Select the washing time Select the washing time according to the laundries Figure 4 6 After washing the buzzer will ring Set the WASH SELECTOR at DRAIN Figure 5 Water filling selector handle Spin timer The buzzer will ring when to set to below 1 minute the washing finishes irst set to 2 minute then turn it back it can increase the service life of the timer 3 SPIN TIMER WASH SPIN INLET SELECTOR Figure 1 Figure 2 srRoNc E STANDARD DRAIN WASH SELECTOR Figure 3 Noc Figur
11. n tub too much There may be some aed eH LT t is the water remained in the factory inspection first use of the of performance machine 15 Packing list Name Quantity User s manual e One piece e One piece e Lint filter ux e One piece Gland One piece e Water filling jointer re One piece Twin tub washing machine e One set X Specification f N Water level Water quantity about Maximum 43L Medium 36L Minimum 30L Rated washing capacity kg 5 5 Rated spinning capacity kg 5 0 Injection pressure MPa 0 02 0 2 16
12. sh tub side hands Take care not to damage the drain hose in fastening the fixing clamp Erbedi a mbed into the E groove in turn Extend the drain hose from the rear side Take out the drain hose from the fixing groove Extend it from the rear side as per the direction of the arrow When the drain hose is extended from the rear side it can be hung on the e point for drain hose at the two sides of the cabinet 0O Te See to Figure 4 Figure 4 Install the water inlet hose Select the water level Insert the water inlet hose into the water filling Water inlet hose entrance on the control panel directly pull it out to dismantle it Figure 3 Select water level according to the Waterfilling quantity of the laundries Adjust the water level adjusting lever to Water level desired water level line indicator Attention In water filling do not exceed the High water level Otherwise the water may overflow out of the washing machine Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention
13. times 1 Put the laundries into the wash tub Select suitable current according to the laundries 2 Fill water to preset water level 3 Rinse Adjust the wash timer to 2 3 minutes to do rinsing When the laundries quantity is below 2 4kg please use Standard current If you use Strong current it may splash 10 Put the laundries into the spin tub evenly and smoothly Press the gland in the tub properly Close the inner and outer cover of the spin tub Spin Select suitable spin time according to the laundries and do spinning During spinning if there s abnormal sound it is generally owing to slanting placement of the laundries Please stop the machine and re order the laundries n spinning it will pause the work if you open the outer cover of the spin tub Close it to resume the spinning S To do spinning and draining or rinsing with water filling together please first do spinning for around 1 minute then do draining or rinsing with water filling Otherwise the spinning will stop owing to too much water stored in the spin tub 11 Disposal after washing e After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine e Please first pull off the power plug from the receptacle before cleaning Cleaning the lint filter The lint filter must be used during washing 9 t must be cl
14. to followings before washing the laundries Check if on washing etc e Clear the The quantity of When the pulsator the laundries pocket Take Me the long the laundries is running the ps fasten has special out the coins the buttons shall not be too buttons of the requirement Sand hairpins close zippers large Stretch laundries may and loosen the laundries before putting them in the tub c2 cause noise For the sake of discretion please put the laundries with buttons into other laundries N QOooco Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other laundries Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur tum it over before putting in f Do not put those laundries polluted by chemicals into the washing machine directly The musts in washing e The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time Laundries quantity in one washing cycle shall be lower than the rated capacity
Download Pdf Manuals
Related Search