Haier HWM50-10H User's Manual
Contents
1. Lint filter Installed by user a Drain hose Lint filterA Installed by user wee SHN Control panel Filter cover Power line Control panel film Cabinet back cover base frame s T fed foot 3 Meaning and description of the symbols Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Warning sign Forbidden sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety ofthe user Safety precautions Please insert the power cord into special receptacle with rated voltage Be sure to use single phasethree pins receptacle Ensure the earthing prong of the power receptacle is earth edreliably Use leakage protector if possible The power cord plug should be convenient to be pluged in or pluged out with hand while the washing machine runs normally Be sure to pull the plug out and close the water tap when the machine is idle when moving the machine or when cleaning the machine Do not use wet hand to ins ert or pull out the power plug Do not damage the power cord bend extend twist bind or alter it by force Do not press or nip it with weight If the power cord or the power plug2. on page 11 e Confirm the reserve program Page 11 La ff When Reservation becomes active the nixietube displays the time to the endof the reservedwash cycle andthe indicator turnson Tochange the running program or cancelthe reservation you should cutoff the supply and reselect Confirm the heating function Keep pressing the RESERVATION CALEFACTION button for morethan 2 s the heating indicatorturns on red Keep pressing the RESERVATION CALEFACTION button for morethan 2 sagain the heating indicator turns off and heatingfunction is cancelled After the machine starts running ifselection or cancellation of heating function is desired youshould switch offthe power andreselect 6 Press the start pause button Close the top lid Except water filling excluding heating function and draining process if the top lid is opened the machine will stop running and alarm Finish washing The washing machinecuts off the power supply automatically when washcycle ends 14 Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning The lint filter must be used during washing t must be cleaned in time after each using Install ae NY 1 Pull upward to dismantle lint filter 2 Push downward to install lint fi
3. hairpins etc the rated value laundries may The big laundries cause noise For like the jeans the sake of shall be put in discretion please loosely put the laundries with buttons into other laundries NN AT a Please check if the laundries are applicable for washing b Separate those not colorfast from other laundries c For laundries not water absorbing please put them into water with hands d For laundries with much soil please remove the soil first You can add detergent on the part with serious soil directly It is much easier to remove the soil by that mean e For laundries likely to get lint ball or with long fiber please first turn the inside out before putting them into the water f Do not put the laundries polluted with chemicals directly into the washing machine G For those small laundries laundries likely to be twisted or worn and woolen laundries please put them into mesh bag before washing h Do not select heating function for clothes that should avoid hot water or wear i In order to prevent the heating band from being entangled washing of seriously worn or linty clothes should be prohibited Put in the laundries The capacity ofwashing and spinning of the machine refer tothe largest weightof the standard laundries under drycondition that canbe washed or spinned inone time Onetime washing quantity shall be lowerthan the rated capacity The largest capacity of thismachine
4. is 5 0kg The thickness size type of thecloth will influence the actual washing capacity Itis suitable forone time washing to put in reasonable amount of laundries and thelaundries can beturned round in washing Do not select High water levelfor laundries less than 1 0kg soas to avoidsplashing of water Towash thin laundrieslike the stocking silk etc please first putthem into washing mesh bag which Usage of the detergent ey Inlet box of the detergent How touse the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolve it before use can be purchased separately before wash How to use the washing powder Direct dissolved in the machine 1 Fill water to Low water level 2 Add the power Run for 30 seconds to dissolve it completely 3 Put in thelaundries Select suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 Cand a container 2 Add the powderwhile stirring to fully dissolve it Put inthe prorer quantities detergent according tothe water level and the laundries quantities It is suggested notto use high sud
5. is bad or the power plug becomes flexible to avoid risk it is required to have it replaced by the technicians of our special shop or the after sale service department Keep the pin of the power plug clean if the power plug is polluted with dust please wipe with dry cloth carefully Do not put the machine at damp place like the bathroom Never wash it with water Not put wet laundries on the control panel Do not use water hotter above 50 C In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet The ventilation holes at the bottom soft items 9 Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more ed Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not let the children climb the washing machine Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc The handicapped or child
6. selected for Normal Jeans Gentle and Quick programs butit s unavailable for Rinse process 2 If heating function is selected for water levels 1 or 2 it begins to heat after water reaches the setlevel and beginsto wash when the set temperature is reached for water levels 3 6 it begins to heat upon water reaching level 2 it continues water supply and gently agitates while heating to the set temperature then it begins normal washing for water levels above 6 the cycle is after water reaching level 2 it begins to heat meanwhile water supply continues until level 6 water supply stops and it continues heating to the set temperature then it begins to wash while water supply is resuming the hot water temperature then is good for detergent active enzyme function and for the clothes to be in an optimum detergent concentration with a good washing effect The subsequent washing while water supply can facilitate dirt flushing and removing water supply stops when reaching the set level then it continues to wash normally For high water levels only the water amount below level 6 can be heated to the set temperature then it washes and supplements water to the set level 3 This washing machine provides 3 temperature selections of 20 C 30 Cand 40 C eachranging as follows 20C 5C 30C 5 C 40 C 45 C Names of the parts Top lidA Water absorption cushion Top lid B Detergent box Cabinet handle
7. Fuzzy Computerized Automatic Washing Machine User s manual This manual is for HWM50 10H e Please read this manual carefully before using eRetain it for future reference Contents Names of the AMS ncvesasactevacncssint tinue sitrnputhdnnesnesosisneessuandialdinmnestcheminisastnamciieetas 1 Safety precautions wists tabicassiransaseoocsspnieinnssuna ebaawsuaderZeareuanciianesned eddeatsetesticincun 2 Installation and adjustment casssnssisoncndodehcenavenssan dirs ssiaatucotarioieenndhdeicsinleatucinsaiel 4 Preparation before washing ciccsecieseivsshssensesdedbcosnacadectcatereslccsonstdoeccceantctuentehibed 8 P t ii th laundries cirneiste aii 9 Usage of the detergent isessserserrnsseserssrenssnrrenrerunnsonrenrrnnnsenennrrnennernnnrrnane 9 Use the operation buttons cacissscsnacaciesasanesaveansnessiiessaisnciduensiachdvecenanstbiecaninnsaeiains 10 Close the top lid sassgecaztctitesiscasshctsifiatecp vveueansyh aes vsantandudlaeilaaysttalabeatebtenite 14 Finish WelSINNG c ches2tececoseacscose oe deoponscensansertaatiasseemaciuneeststeeaneteasaneucyiiaie 14 Di posal after WOSIMMG a s tccecocaiattestiakorenceactonercuneibacunemccinantes 26 15 Trouble shooting Answer to QUGStIOMS sc sseescsesscssessstessssesstesennt seen 16 Packing list SPCC CA NON cc ice3 nccesitccbastuceiecaechitatensiaclnsharacblalacslesamniaisenndiiateccia ad 17 Description of heating function 1 Heating function can be
8. ched on press itto To indicate remaining min During w 4 start the machine program running During working push it to pause working a e To indicate remaining reserved m During pause push this button to restart time hrs during reservation period m and cominue operation To indicate fault symbols for abnormal m conditions see page 16 a POWER ON OFF button E a Press Power On Off button to P connect power supply A After power is connected pressing this button will cut off the supply SURPLUS MIN Ove m E Qoc a a XLVI SYNOH JAYISJY POWER START ON OFF RESERVATION CALEFACTION button Press RESERVATION CALEFACTION button to set scheduling or heating Function If heating function is selected the scheduling function is unavailable During machine running the display indicates the cycle remaining time in minutes Press RESERVATION CALEFACTION button the display will Indicate the remaining scheduled time to cycle end in hours the decimal point flashes to indicatethe scheduled progress Heating function can be selected if keep pressing RESERVATION CALEFACTION Button for more than 2 s If the temperature indicator is lighted itmeans heating function is selected If keep pressing The RESERVATION CALEFACTION button for more than 2 s the temperature indicator turns off and the heating functionis cancelled The initial temperature is about 30 C and yo
9. e speed of draining is too slow The digital tube displays E1 and it rings Is the drain hose blocked by foreign material Is the drain hose frozen After long running of pump in the hot weather power will be cut automatically for safe Clean the foreign material Open and close the top lid once Clean the frozen material Some minutes later the machine will continue to work It stops running except water filling and draining The digital tube displays E2 and it rings The top lid is not closed Close the top lid The safety switch acts The spinning cannot work after twice revising The digital tube displays E3 and it rings Are the laundries put slantingly is the machine slanting Re order the laundries Close the top lid Level the machine in right position Open and close the top lid once It does not do water inlet or the speed is slow the water level is not reached after 15 minutes The digital tube displays E4 and it rings Is the water faucet open or is there water supply failure Is the water inlet valve is blocked Open the water faucet Open and close the top lid once Clean the water inlet valve Open and close the top lid once The machine does not act The indicators are off Is there power failure s the power plug loose Use it when the power is on Insert the power plug tightly There s abnormal s
10. e water 2 Hang the locklever to thejointer inlet hose Release the slidertill a click Locking lever sound is heard 1 Swaying the hose gently to confirm if itis fastened stable 2 After installation openthe tap tocheck if itleaks 3 Do not bend the hose with overstrain 4 Before each usage please check if the connection between the jointer of the water inlet hose and the water tap and the installation of the water inlet hoseare firm soas to prevent dropping from improper 1 Close the watertap 2 Press the lockinglever Pushdown the slider Then pull offthe water inlethose If the machine is used more than onceevery week thejointer of the water inlet hose canbe kept onthe tap toprevent damaging the fixing screw Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe Hang up the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Confirm if Clear the pocket Fasten the The quantity of When the pulsator there s special Take out the buttons and the laundries is running the requirement for coins sand zippers shall not exceed buttons of the the laundries
11. ee to Figure 1 3 Loosen the screw till the water tap can be accessed Put the jointer of the water inlet hose on the tap See to Figure 2 If the tap diameter is too large and the jointer can not be set on the water tap please loosen the four screws and take out the bushing in the jointer See to the figure3 bushing pe Water inlet pipe Figure 1 Figure 2 Figure 3 4 Fasten the four screws evenly See to Figure 4 5 Take off the nameplate Twist the fastening nut as per the indication of the figure See to Figure 5 Remarks Before twisting the fastening nut the thread is4mm above the upper surface ofthe nut After twisting the fastening nut thethread is 2mm above the uppersurface of thenut See toFigure 6 About 4mm before twisting About below 2mm after twisting Figure 6 Connection between the water inlet hose and the washing machine 1 Do not take off the water absorption Nut of the water inlet hose cushion Please checkif the cushion a S amp S is dropped ordamaged before each usage If ithappens please contact TA X 2 Put the nutof the waterinlet hose on the valve jointer 3 Fasten the nut Swaying it gently to Water absorption cushion confirm if it s suitable Jointer of the water inlet valve our after sale departmentimmediately 5 Connection between the jointer of the water inlet hose and the water inlet hose 1 Push down theslider Insertthe DI water inlet hoseinto the jointer i Jointer of th
12. he bracket on the drain hose There is a hole on the cabinet to hang the drain hose as figure 3 1 Dismount the back cover of the washing machine Figure 3 7 drain hose rack Figure 1 m 4 install the back cover as what it looks before 2 Take off the drain hose frame Put down the drain hose Take off the drain hose rack As indicated in Figure 1 Pull the drain hose into the cabinet from the left side of the bottom as figure 2 Usage of the drain hose The drainage shall be smooth with the drain hose 1 put the drain hose up to suitable position Do not putt on ground 2 Do not step on or press the drain hose Notes the highest point of drain pipe should be higher than the water level of washing tub for avoiding to siphon phenomenon during drain The highest point E S v Vv 5 s Install the water inlet hose Confirm the water tap Water tap suitable Water tap not suitable Outlet end surface It is required that the frontend shall belonger than 10mm The outlet end surface of thetap shall beflat and smooth If not please file it to avoid leakage Connection between the water inlet hose jointer and the water tap 1 Use the new water inlet hose provided with the machine to connect to the water faucet Old hose sets should not be reused 2 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component S
13. ing Soak Wash Rinse Spin ides tub liquid O He a The laundry needn tspinto Soak Wash Rinse Spin in the ub avoid wrinkles O O e Ri When the laundries need Soak Wash Rinse Spin rinsing and spinning after RR manual washing 2 O O When the laundries need only Soak Wash Rinse Spin inteni in Spinning after manua Spin spin after drain washing first drainthen spin J J O If the laundries are very dirty Soak Wash Rinse Spin or the sleeveand collar are dirty firstsoak then wash O O O O Soak wash rinse spin If you pushthe PROCEDURE SELECTION button for 6times it willresume the original mode andit will circulate like that If you selectthe QUICK WASH program you haveto set the full procedure of wash rinse andspin The procedure can notbe selected 13 4 Press the WATER LEVEL button to select suitable water level LEVEL SELECTION After switching on the power press the button WATER LEVEL to select a water level according to the load Please refer to the button Water level on page 10 5 Push the RESERVATION CALEFACTION kem button to select suitable reserve TION mE After switching on the washing machine reserved wash programwill be automatically set inactive If you desire a wash cycle to endat a reservedtime you can press the RESERVATION CALEFACTION button to seta reserved wash program Refer to The button of RESERVATION CALEFACTION
14. is desired you can press the button PROGRAM SELECTION to getthe corresponding indicator on Refer to the Button of PROGRAM SELECTION paragraph on page 10 Page 10 Example Use the Quick program for slightly soiled articles When standard programis selected the washing machine will perform full automatically controlled fuzzy program to setwater level waterflow and washduration according to thecloth nature andweight 3 Press the button of PROCEDURE SELECTION to select suitable processes iit SELECTION After the power is switched on the washing machine will automatically set anormal program comprising of processes of Wash Rinseand Spin If other program is desired press the button of Process to select one or several process of soak wash rinse and spin Refer to the paragraph Processes selecting e Even there s nowater in thetub the spinning will start after acertain period e Do not usesoak process for woolen laundries e Wash thelaundries that are prone to lose color separately fromother laundries The pulsator will not rotate unless the water is filled to selected water level Times of pushing Selected procedure the select button program Contents the lighted indicators Applicable procedure indicate the programs about to run asni f winen me rommen laundries Soak Wash Rinse Spin need washing rinsingan ash rinse spin eena g g e O O O Wash the washing Repeat using the wash
15. lter OIRA Dismantl Install 3 Please clean lint filter after wash Dismantle amp Install The filter screen of the water inlet If the cabinet is dirty wipe it with wet cloth valve is likely to be blocked by e Do not flush it directly with water foreign materials and influence the water inlet Please clean it e Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 Do not store water in the washing machine for a long period Drain the water completely after each using 3 Be sure to pull off the power plug before maintenance 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid 15 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do notrepair it by yourself Phenomena After the reservation is started it rings and the digital tube displays E0 Reason The top lid is not closed How to settle Close the top lid The draining does not work or th
16. ound inside the machine Is the machine slanting Is there metal material inside the washing machine Are the laundries slanting in spinning Level the machine properly Fasten the buttons and zipper Re order the laundries Close the top lid The water faucet leaks s the jointer screw of the water inlet hose is loose or twisted awry Common phenomena Fasten the jointer screw properly Phenomena The spinning is intermittent when it starts Explanation Balance the laundries to avoid slanting Pause during washing supplemental water filled after fabric sensor has checked fabric about 48 seconds Select spin but it doesn t work The program is setting the drain time Some time is needed before it starts spinning There may be some water flowing out of the drain hose in the first use of the machine Itis the water remained in the factory inspection of performance The Pulsator turns mildly after inlet the water but always feels immobilly If heating function is selected before reaching the selected temperature in order to let the water heating uniformity the Pulsator turns mildly After arriving the Selected temperature it can works in gear Select the heating function the temperature indicator is lighted sometimes twinkles sometimes not When the machine is in heating sate the temperature indicator twinkles Selec
17. ren without care shall not use the machine Keep the machine away from direct sunlight and heat source like the heater Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the lint filter Install the bottom plate After you open the package please lean the washing machine gently down on soft items like the towel cloth blanket etc Install the bottom plate to the bottom of the machine with the eight screws by across LE ES NV screwdriver then lift the machine up gently Install See to the figure v Te Push lint filter downward to location for lint filter Back gt o Wt w Soft items ae Bottom plate The largest allowed slope of the shank base of the machine is 2 The slanting or rough ground will T E result in unstable running or stoppage of the machine Please adjust it with following methods Adjust the adjustable foot 1 To twist the adjustable foot please first lift up the side of the foot slightly loosen the adjustable nut and twist the foot 2 Fasten the nut after adjustment How to change the direction of the drain hose 3 protrude the drain hose from the hole on the right side of the bottom and fast it onto the bottom with the rack and screws Set t
18. sing detergent Washing powder with poor quality or long time storage maybe caked Please pay attention to cleaning the detergent box intime Use the operation buttons a Description of the function of the buttons 9 7 5 3 1 WATER LEVEL button The user selects a suitable water level depending on the load If Quick wash is selected water level will indicate 2 After water level reaches 2 it will wash while water filling and wash normally upon the water level reaching 4 After washing for 1 min pressing Water level button will enable supplemental water filling which will stop automatically upon the water reaching overflow level MAOO PROCEDURE button With it you can select one or several processes of soak wash rinse and spin STANDARD m ca m CO SOAK WASH C GENTLE m CRNSE _ QUICK WASH To SPN PROGRAM button You can select from the following four programs Standard Normal wash Jeans Large thick or heavily soiled laundry Gentle Woolen textiles or underwear Quick 10 min quick wash for load below 1 kg Remarks After pressing POWER ON OFF to connect power supply if the washing machine lasts idle more than 10 min it would automatically shut off the supply 10 SURPLUS MIN START PAUSE button To indicate during sensing After the power is swit
19. t the heating function if notin the sate the lighted does not twinkle When the power plug is inserted the computer board indicator is switched on and the machine starts working It isthe special power resume function Inthe case of power failure or the power plug is loose during washing the machine can save the running program and resume the program after the power supply is recovered You do not need to set the program again Packing list Name machine Specification Quantity Storage position User s manual One Inside the document bag Warranty Card One Inside the document bag Components ofthe water inlet hose One Inside the accessory bag e Lint filter One Inside the document bag e Lint filter A e One Inside the document bag Bottom plate Between the upper cushion of One the washing machine package and the upper seal of the package carton Tapping screws D Z Eight Inside the document bag d A g Fuzzy computerized automatic washing e One a Water level Water quantity about 1 13L 2 16L 3 22L 4 27L 5 30L 6 33L 7 36L 8 39L 9 42L 10 46L Water inlet pressure 0 03MPa 0 78MPa Rated washing spinning capacity kg 5 0 kg weight of standard dry cloth 17
20. u can select your desired valuein 3s ina switching sequence 30 C 40 C 20 C After the machine starts running ifselection or cancellation of heating function isdesired you should switch off the power andreselect b Operating procedure and explanations for the buttons 9 10 7 8 5 6 Osoak SURPLUS MN Owr 3 r Q EANS Oms i Ozor 1 2 Q GENTLE RINSE 3 Ove Ooauick wash OPN E RESERVATION ALEFACTIOI WATER LEVEL SELECTION 1 Press the POWER ON OFF button to switch on the power supply POWER After switching on the washing machine heating function will be ONOFF automatically set inactive in order to select heating function the RESERVATION CALEFACTION button should be pressed for more than 2 s until the heating indicator is lighted which means the heating function is selected The initial status is 30 C and 40 Cor 20 C can be selected if you press RESERVATION CALEFACTION button again in 3s It has the special power resume function In the case of power failure or the power plug is loose during washing the machine can save the running program and resume the program after the power supply is recovered You do not need to set the program again 2 Press the button of PROGRAM to PROCEDURE select a suitable full automatic program After switching on the Standard program will be the default If other full automatic program
Download Pdf Manuals
Related Search