Haier Washer HWMP65-918 User's Manual
Contents
1. 182. 2 Place the plate on to the bottom of the machine Front 3 Use a screwdriver to tighten the screws in accessory bag securing the panel to bottom of Back the washer 4 Once all screws are tight and the panel is secure return the washer to its standing Cparpet Bottom plate position Balance washing machine Do not install this machine on an incline greater than 2 Installing machine on an angle or on rough ground will result in unstable running or stoppage of the machine Please adjust it by the following method 1 Confirm it is level 2 Lift up the side of the leg slightly and twist the adjustable leg Note The distance between the washing machine and wall at least 20 mm Installation of drainage hose Install drainage hose A First connect the drainage hose to the connection point on the lower A left side of the cabinet and fasten with drain hose hoop provided Connect drain hose guide on to the outside of drainage hose To guide the drain hose over the tub or standpipe the hose guide MUST be fitted to the drain hose Drain hose neck guide 8S Drain hose hoop L Drain hose joint i x Placement of Drainage Hose A The height of the standpipe or tub should be between 850 1200 mm A To avoid syphoning the drain hose should not extend more than 20 mm from the end of the guide Ensure drainage hose is held in place to avoid leaks or spill
3. e Redistribute the laundry There are abnormal sounds inside the machine ls the machine level e Has the laundry been placed unevenly in the machine Are there any foreign objects inside the bowl e Redistribute the load evenly Close the top lid e Level the machine e Remove the foreign object The water tap leaks e Is the water inlet hose loose e Fasten the inlet hose Common occurrences Situation Cause e The spinning is intermittent after e Redistribute the load evenly it starts Close the top lid The wash procedure pauses e The cloth sensor is detecting it will add water after about 48 senconds e Select spin program but it does The program is setting the drain time there not work will be a pause before the spin program starts e There maybe water in the e It maybe residual water after performance drain hose in when first used inspection by the factory 16 Packing list Name Quantity Storage position Automatic washing machine Bottom plate One Between the upper cushion of the washing machine package and the upper seal of the package carton User manual Inside the document bag Warranty card Lint filter HWMP55 918 i Inside the document bag Inside the document bag Tapping screws P 0 Inside Accessory bag Components of the water inlet hose Connect to the washing m
4. mante Dismanth Install i f f Ke The front cover of lint filter Remove and clean the detergent box replace after cleaning The filter at the water inlet valve may If the cabinet is dirty wipe it with a damp F maai loth become blocked by impurities in the e water supply Clean it with a plastic eDo not wash directly with water e Wipe with a neutral detergent please pristed Brush every two months check directions on detergent bottle first eDo not wipe machine with thinners petrol alcohol or other harsh solvents SSS Was DRY Yo LA 1 After washing cycle has finshed turn off the water faucet If needed you can remove the water inlet hose 2 Do not store water in the washing machine for a long period without completing a wash cycle Drain the water completely after each wash 3 Hang up the power cord and drain hose 4 Wipe up any drops of water on the surface of the machine and inside the tub Leave the lid open for about 1 hour after each wash to evaporate any residual water 14 Trouble shooting If there is a fault or the machine does not operate correctly remove the power plug before checking the machine Using diagnostic list below please check the machine requires repair If a repair is required please contact our Customer Care Team do not try to fix it yourself Problem The machine does not drain or drains slowly The display shows E1 Possible caus
5. work During wool cycle the hot cold water temperature cannot be chosen F START PAUSE button After the power is switched on press the Start Pause button to start the machine During operation push the Start Pause button to pause the machine Push the Start Pause button again to restart the machine G POWER button To turn on off the power press the power button e If the start pause button is not pushed within 5 minutes the washing machine will automatically switch off the power Button Operation and Descriptions 1 Press the button to switch power on off POWER 2 Press the Gre button to select automatic program When the power is switched on Normal cycle is automatically set To select N a different automatic cycle press the Cycle button till the corresponding indicator is on Refer to the section on the Cycle button above E g choose Quick cycle for a small load of lightly soiled laundry When the Synthetic Memory cycles are selected the Fuzzy Logic program is run The washing cycle is automatically set while the water level and wash time can be selected according to the texture and size of the load 11 Operation amp Wash Cycles 3 Press the E buttons to customise the pre set options Even there is no water in the tub a certain period is required before spinning Separate colour fast clothes before loading was
6. Automatic Washing Machine User manual This manual is for HWMP55 918 HWMP65 918 Please read this manual carefully before using Retain for future reference CONTENTS Product Overview rere eee re err errerrerr err err ere ere re ery Safety PreCauUtiOnS scr cer cee cee cee cee cee cee cee cee cee eee Installation and Adjustment 6K 0 0 aie wwe eee Sale wwe 4 Installation of drainage NOSE res cet cee cee cee cee cee cee cee nee Installation of water inlet hose Loading your laundry te eee ere ee Prrrerrrerre rr err err err Detergent usage guide ose sos es se ess sse too ose ses ose Operation amp Wash Cycles ous eeo sst cos ser oco sst eos Maintenance Trouble shooting seeeeeeeeeeerereerreeereereeeesrerensereee Packing lister cee cee cee cee cee cee cee cee cee cee ene cen cee cen cee nee Product Overview Cold water valve Hot water valve Lint filter HWMP55 918 Balance ring AE Tp LA Lint filter Inner tub Pulsator Control panel Cabinet Fixed leg Drainage Adjustable leg hose Back cover Description of symbols Contents marked with this symbol are related to the Warning sign safe use of the product and the personal safety of the user Please operate in accordance to the contents of Q this manual to avoid harm to the user or damage to the machine itself Contents marked with this symbol indicate operations or actions that should not be
7. Select suitable water level Push the Start Pause button again to recommence washing cycle If you select Quick program it is recommended to use liquid detergent instead of washing powder to ensure the most effective wash results Old or poor quality washing powder may causing caking in tub or detergent dispenser Clean the detergent box periodically to ensure washing power is evenly distributed and remove any detergent buildup Note For best wash performance use low suds High Efficiency detergent and dissolve the detergent in lt 1L warm water prior to mixing with laundry Close the lid If you open the lid during alarm will sound spin cycle the machine will stop and an audible Operation amp Wash Cycles Memory IfA nomai Long B 3 stago E 9 Min Minutes Remaining 9 E Hotcola AR Synthetic fiie K AE Wares 7 Min Warm Cold Ss HG Wool m ma Rapid Bi stage 9 WO Min 3 4 E Cold Cold POWER E Tub dry O mo CETS MERA i i Water ro START PAUSE Fuzzy Logic Indicator display E Off On Indicates the program is about to run and indicates the selected cycle and options 0 Flashing Indicates the program is running and indicates the selected cycle and options Remaining time display Displays during Fuzzy Logic detection cycle until level is determined Displays total
8. achine Connect e Inside Accessory bag Drain hose Inside Accessory bag Drain hose Guide Inside Accessory bag Drain hose Clamp Inside Accessory bag 17 Specifications Fully Automatic Washing Machine HWMP55 918 HWMP65 918 Rated voltage frequency 220 240V 50Hz 220 240V 50Hz Rated washing power 380W 390W Rated spinning power 340W 350W Net weight About 32 5kg About 36 5kg Gross weight About 37 5kg About 41 5kg Dimensions mm L520 W530 H 900 L550 W560 H955 Water level Water 1 14 L 2 18L 3 22L 1 18L 2 24L 3 30L Quantity approx 4 26L 5 30L 6 34L 4 36L 5 42L 6 48L 7 38L 8 43L 9 47L 7 54L 8 60L 9 65L 10 52L 10 70L Water inlet pressure 0 03MPa 1 0MPa when water temperature is 50 C the water inlet pressure of hot water shall not exceed 0 4MPa Note Default settings when you choose this program after power on eyr Wash Rinse Spin Water level Temp Time 97 Min HwmMP55 918 Normal Long 1 Rinse 7 Min 10 Warm Cold 107Min Hwm6s 918 Heavy Long 2 Rinses 7 Min 6 Warm Cold 76 Min Delicate Rapid 2 Rinses 5 Min 6 Warm Cold 34 Min Quick Express 1 Rinse 3 Min 3 Warm Cold 10 Min Memory _ This cycle setting remembers the last wash rinse and spin settings Synthetic Medium 1 Rinse 5 Min 6 Warm Cold Wool Express 2 Rinse 3 Min 6 Cold Cold 25 Min Tub dry 53 Min
9. be on e During the delay program press the Delay button to display the time remaining The delay time indicator shows the time remaining till the wash ends e To cancel the delay program switch the power off and back on then make a new selection e Delay start 2 24hr option e Delay time is to the end of washing washing cycle 12 Operation amp Wash Cycles 7 Press the 1 button to start the cycle Start Pause e If the top lid is opened while machine is in SPIN cycle the machine will stop and an audible alarm will sound Note The energy test program was performed using the Normal cycle default setting of Wash Long Rinse 1 Rinse Spin 7 mins Water level 10 e Please use low suds high efficiency detergent Cycle completed When the machine has completed the selected current wash cycle an audible alarm will sound and the machine will switch off automatically 13 Maintenance Remove the power plug before carrying out any cleaning or maintenance e Clean the lint filter s and detergent box after each wash The lint filter must be used during washing It must be cleaned after each use Lint filter 1 Slide upwards to remove 2 Gently push it down to install ensuring it is in place before next wash Directions for cleaning lint filter on model HWMP55 918 MENU Sa Dismantle remove Install Directions for cleaning lint filter on model HWMP65 918 ar Di
10. be washed The thickness size and type of clothes will influence the actual capacity Do not select more than Water Level 4 for clothes less than 1 0kg to avoid splashing of water It is recommended that low suds High efficiency detergent is used Detergent Usage Guide How to use Bleach whitener Always refer to the bleach whitener instructions prior to usage Fill water to desired level Dilute the bleach whitener in a container Pour it Avoid using whitener on laundry with colour or patterns as they are prone lose colour NOT be directly applied to laundry directly slowly into the washing tub The bleach whitener should Adding washing powder It is suggested to dissolve detergent before adding to the tub see as below 1 Prepare warm water lt 35 C in a container 2 Add washing powder stirring to dissolve it completely Adding washing powder Fuzzy Logic Programs Add washing powder liquid into the detergent box directly for Fuzzy logic programs and Delay program Adding washing powder Normal Wash It is recommended that washing powder liquid is dissolved with water and then directly emptied into the washing machine not applicable for Fuzzy Logic and Delay program 1 Add some water select the 1 water level 2 Add washing powder liquid Run for about 30s to fully dissolve the detergent Then push the Start Pause button to pause the wash cycle Load laundry
11. ectrical socket 3 Ensure the drain hose is mounted at the correct height 4 Select a suitable location for the washer on a hard even Surface away from direct sunlight or heat sources e g Radiators heaters cooking appliances etc 5 Any floor unevenness may result in unstable working or abnormal noise Please ensure the machine is level Clear the Pockets items such as coins sand hairpins etc So Tie any long and take out loose Straps or strings fasten buttons and close Zippers The weight of the laundry shall not exceed the rated capacity of your machine Loosen the laundry before placing it evenly in the tub Q When the machine is running buttons may cause noise To reduce the noise turn clothes inside out or place them in a laundry bag RR S a Check if the laundry is suitable for machine washing b divide the laundry into colour fast and non colour fast items c separate items that do not absorb water easily and wash by hand d for heavily soiled items please first remove loose dirt then apply detergent directly as per instructions on pack to the stain before washing e for those items that may attract lint or are furry or fluffy please turn inside out before washing f do not put laundry soiled with chemicals or solvents into the washing machine e laundry The rated washing capacity refers to the largest dry weight of a load that can
12. es e Is the drain hose blocked What to do e Remove the blockage Open and close the top lid once The machine stops running The display shows E2 e The top lid is not closed Close the top lid The machine does not spin The display shows E3 e Has the laundry been place unevenly in the machine e Is the machine level Redistribute the load evenly Close the top lid Level the machine The machine will start 10 seconds after being leveled correctly The display will show E4 e Is the water tap closed or has the water supply been interrupted e Is the water inlet valve blocked e Is the water pressure too low e Open the water tap Push the Start Pause button once e Clean the water inlet valve then push the Start Pause button once e Use after the water pressure is normal The display shows E6 e The water level sensor has failed Please contact Customer Care Will not wash The machine does not e Is there a power failure Is the power plug inserted tightly e Has the water level reached preset position e Wait for the power supply to be restored e Insert the power plug tightly e Wait for water to fill to the preset level work Will not spin e Is the power plug inserted tightly e Is the top lid closed e Is the laundry distributed unevenly in the machine Insert the power plug tightly Close the top lid
13. f power cord or other parts of this machine become damaged or faulty please contact a technician to have it repaired DO NOT attempt repairs yourself as this may cause personal harm or void warranty e Please remove items such as coins buttons sand and other solid materials from clothing before washing oT l AO Check that water faucets are open Please use low suds High after connection to machine prior to operation and that pipes are connected correctly Efficiency washing powder Installation amp Adjustment Please install and adjust the machine according to the directions contained in this manual It is very important to follow these directions for the safe operation of the machine and to ensure your machine operates correctly Install the lint filter After removing washer from outer packaging take Model HWMP55 918 out the lint filter from the document bag install it to the inner tub See the figure opposite linner tub Please ensure the lint filter is installed correctly and maintained in good condition to ensure the water outlet is EI not blocked or the flow altered If the lint filter is lost or Model HWMP65 918 damaged contact Customer Care Up j Dismantle Install if SN Down Install the bottom plate The purpose of the bottom plate is to suppress noise from the washing machine during operation Steps 1 Lay the washer on its back on a non abrasive surface
14. hing machine During Rinse cycle only SPIN times can be set all other wash functions are locked e During Wool and Tub Dry cycles these settings cannot be changed and buttons will not function as machine will only follow pre programmed settings iT Eki 4 Press the button to change the water level For the Synthetic and Memory cycles the machine will run a Fuzzy Logic program that automatically detects the type of laundry in the tub After detection it will set the water level automatically The water level can only be changed once the machine has started by pushing the Start Pause button then push the Water Level button to reset the water level Press the Start Pause button to resume the wash cycle 5 Press the 22 button to select the the wash and rinse temperature Set the wash and rinse temperatures in accordance to the requirements of each load The wash and rinse temperatures will be the same i e if Warm Cold is selected both wash and rinse cycles will be warm cold 6 Press the eta button to select the delay wash program The delay time program is automatically off and wash cycles will start as soon as Start Pause button is pushed Confirm the operation of Delay program e To set a delay time first select the Cycle and options required and push the Delay button The cycle indicator lights will go off and the Delay Hours indicator light will
15. ion or cause an electrical fault Do not block the ventilation holes with Do not wash water proof clothing carpet Ensure carpet does not obstruct as this may affect load balance the opening under the base of the during spin cycle s cabinet The ventilation holes at the bottom Back i Soft object EA Q If you are using an extension cord or a portable electrical outlet device not recommended ensure that it is positioned so that it does not come into contact with water or moisture S Safety precautions Do not attempt to move washing or place hands inside washing machine while in operation Please ensure children are supervised around Do not take apart repair or alter the machine by yourself Do not leave hot or heavy items on lid or control panel as this may cause damage to the washer or make the washer unsafe to operate Do not wash laundry with chemicals or other volatile materials such as petrol solvents or thinners as this may cause damage o to the machine This clothes washer is not intended for use by children and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Keep washer away from heat sources such as heaters stoves or direct sunlight I
16. ng Delay start can be set for 2 24hr operation NOTE The delay time is until the selected wash program finishes you will need to deduct wash time from this delay time to calculate when the wash will start D Water Level button e During the Memory and Synthetic programs the washing machine will detect the size of the laundry and automatically select the water level between levels 4 6 8 or 10 To change the water level press the Start Pause button and make your selection by pressing the Water Level button until desired level is shown 1 10 f there is water inside the tub and the machine cannot detect the laundry load it will display water level 6 If wet laundry is put in the machine it will display level 3 you can then manually adjust to the desired water level e f Quick program is selected it will display water level 3 you can then manually adjust to the desired water level f Tub Dry program is selected the water level cannot be manually overridden e During operation of the wash or rinse program you can adjust the water level by pressing the Water Level button The water level may vary due to the different moisture level of the laundry items 10 Operation amp Wash Cycles E Temp Wash Rinse button Press the Temp Wash Rinse button to select your wash temperature During Quick cycle the water temperature is preset Temp button does not
17. remaining during current in progress wash cycle e Displays remaining time when the Delay program is used hours Displays error codes see page 15 A Cycle button Program Recommended for Normal Recommended for mixed fabrics and general clothing items Heavy Items that are soiled or items that are heavy big Delicate Delicate items that are machine washable Quick Lightly soiled or small laundry loads less then 1 5kg Memory This cycle setting remembers the last wash rinse and spin settings Water level will not be remembered as it is determined by fuzzy logic function Synthetic Ideal for synthetic fabrics Wool Machine washable woollen items Tub dry Dries the inner and outer tub to avoid the growth of mildew Operation amp Wash Cycles B Wash Rinse Spin button e You may change the Wash Rinse and Spin times when Memory Heavy Normal and Synthetic cycles are selected When the Wool cycle has been selected you cannot change the Wash Rinse and Spin times e You can not change the Wash Rinse and Spin times when Tub dry and Quick cycles are selected C Delay button The display shows the time remaining in minutes before the cycle will finish e Push the Delay button and the display will show the remaining time for the cycle to finish in hours The indicator flashes to indicate that the delay function is operati
18. s 7 gt A 0 85m lt h lt 1 2m Installation of water inlet hoses NOTE Use the new inlet hoses supplied do not reuse old hoses 1 Insert a new flat washer into each end of the inlet hose En 2 Connect the water inlet hose to the water faucet You may have OX to use pliers to tighten the coupling Do not over tighten as this may cause damage to the valve or hose fittings 3 Connect the other ends to their respective cold and hot water inlet valves located on the top of the washer Nut of the water inlet hose pF Water absorption cushion to Joiner of the water inlet valve 4 Fasten each hose on the washing machine and ensure a tight connection Check the inlet hose connections securely fastened After installation open the tap to check for leaks Do not bend the hose unduly Periodically check the hose connections are firm at both ends This is to ensure the connections ore remain watertight over time YQ Removing the water inlet hoses Swing the hose gently to confirm that the hose is iA A 1 Turn off the water taps 2 Loosen each connection at faucet and washer 3 Carefully remove each hose separately as they may contain residual water Check if the laundry has any special washing instructions Before washing Preparation 1 Ensure the water inlet hoses are correctly installed and faucets are turned on 2 Insert the power plug into the el
19. undertaken by the user Performing of such actions may result in injury to the S user or damage to machine itself and void warranty Forbidden sign SAFETY WARNING Please check power socket condition to ensure it has been earthed correctly prior to installation to ensure your safety Safety Precautions A separate earthed power socket is Ensure the plug is removed and the required for the power supply Hold the taps turned off in the following cases plug NOT the electric cable when Power failure cleaning moving unplugging the washing machine Do installation and when not in use not insert or remove the power plug with wet hands After installation of the washing machine the power plug should be accessible If power cord or other parts of this CAUTION If this appliance is machine become damaged or supplied from a cord extension set faulty please contact a technician or electrical portable outlet device to have it repaired DO NOT the cord extension set or electrical attempt repairs yourself as this N portable outlet device must be may cause personal harm or Q positioned so that it is not subject void warranty to splashing or ingress of moisture R yf Do not install this appliance ina damp Do not connect to hot water higher or wet environment Do not leave wet than 50 C temperature laundry on the Control Panel or spray water directly on to this appliance as this may cause the washer to malfunct
Download Pdf Manuals
Related Search