Haier Washer HW60-B1286 User's Manual
Contents
1. Note The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning CONNECTING TO THE POWER SUPPLY Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 13A 3 The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug Connect the machine to an earthed socket outlet CONTROL PANEL A Power Switch F Display screen K intense washing button B Program knob G Washing time L end Delay Button C emo button H Times of rinse M Prewash button D Spinning Speed Setting button Spinning time N Rinse Hold button E Washing temperature button J Detergent distribution drawer QO Start Pause button OPERATIONAL FUNCTIONS A Power _ Press the Power button to switch on the washing machine Press it again to switch ott the washing machine Switch Press On Off button gently for 2 seconds to switch off the machine as all buttons are soft touch B Program By turning the Program knob clockwise or anti clockwise anyone of the 12 programs can be selected Knob As the knob is turned the adjacent indication light will illuminate C emo2. 3 It may remain foam without cleaning out after the final spinning cycle Recommendation 1 Clean the detergent drawer once a week 2 When using the prewashing program please add half of the rating dosage 3 Please follow the dosage recommendation on the powder or liquid detergent package Note If the Cotton or Synthetic function is used the washing machine defaults to the Auto weigh function Do not use liquid detergent with the auto weigh program because during the initial part of the program the drum rotates and concentrated liquid detergent will be tipped onto the laundry and may damage the fabric or attect the colours ADDING DETERGENT Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gently Refer to the instructions on the drawer Caution For prewashing program detergent should be added to both compartments 1 and 2 For other programs do not add detergent to compartment 1 Use liquid detergent according to the instructions on its package Do not use liquid detergent if the pre wash mode or Start delay is selected Do not overuse softener otherwise it will damage the artificial fibers SELECTING PROGRAM To get the best washing results an appropriate washing program should be sas selected according to the laundry type Please turn the program knob to A 0 C F select the right program En
3. This function can be used in conjunction with the following programmes Cotton Synthetic Mix After button choosing one of these you the customer can set the following washing time washing temperature rinse time spin speed spin time and choose some additional functions such as Intense Delay Prewash Rinse hold according to the requirement When the combination of wash program has been selected this bespoke selection can be stored for reuse another day by pressing the memo button for 2 seconds the display screen will show the corresponding number 1 represents the programme that has been saved under cotton 2 represents the programme that has been saved under synthetic 3 represents for the programme that has been saved under Mix This means the programme chosen by you the customer has been saved Next time when you to use one of these Cotton Synthetic Mix custom wash programs press Memo the corresponding programme having been saved will be displayed press Start pause button to start this programme Also the setting programme can be used many times until you set a new one the previous programme will be over written Refer to the Wash Program Options table for details D Spin Speed Press the Speed button to select the spin speed The maximum selectable spin speed varies with the wash program button E Washing _ Press the Temp button to select the water wash temperature 15 20 30 40 50 60 70 80
4. 90 The temperature maximum allowable heating temperature varies with programs button F Display screen G Wash time H Number of rinses Spin time J Soop Detergent distribution drawer K intense L End Delay Note in the temperature display indicates non heated washing shing _Display screen displays the following washing time program remaining time number of rinses spin time set water temperature speed child lock state door lock state wash progress bar and alarm message _ Press button to set washing time Press and hold this button to change the wash time The time will increase in steps Note this function is not applicable to the Spin Drain program _Press the Rinse button to select the times of rinsing and the maximum allowable number of rinses is 8 Press the Spin button to select spinning time The maximum allowable spinning time varies with programs See the following table for details _ Open the drawer three compartments can be seen Compartment 1 Prewash detergent Compartment 2 Detergent for programs to 11 Compartment 3 Softener conditioning agent pertume etc The recommendation on the type of detergents is suitable for the various washing temperatures please refer to the manual of detergent _Press the Intense button to increase the washing time during the main washing stage of the selected program This feature is applicable for dirty clothes The illuminated icon indicat
5. Some collection points accept products free of charge We apologize for any inconvenience caused by minor inconsistencies in these instructions which may occur as a result of product improvement and development COMPONENTS THANKS FOR PURCHASING A HAIER PRODUCT Please read these instructions carefully before using this appliance The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation use and maintenance Keep this manual in a convenient place so you can always refer to it for the sate and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings ACCESSORIES Check the accessories and literature in accordance with this list 1x Inlet hose assembly 1x Bottom Cover lx User manual Le 1x Drain hose bracket o i Lmao i yi i Q Ay Blanking plugs PREPARATION PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased d
6. THE MACHINE Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents CLEANING THE FILTER Clean the filter once a month 1 Open the bottom cover 2 Remove the filter by turning counterclockwise 3 Flush the filter clean with running water 4 Replace the filter by turning clockwise and remount the cover Caution 1 The filter must be in place or it may lead to leakage 2 Place a container under the drain pump filter to collect any excess water that may come out of the drain pump when the filter is removed WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances clean the water inlet valve and inlet valve filter regularly MANUALLY OPENING THE WASHING MACHINE DOOR To add clothing when washing after the wash program has started or after a power cut you want to remove the clothing do the following steps 1 Make sure the level of water in drum must under the lowest edge of the door window 2 The temperature of water is not over 50 3 The machine is switch off at the power supply so the drum cannot turn 4 Disconnect the drain hose and place the open end in a bucket lower the end so that the water in the washing machine drains out 5 B connect the drain hose to the drain system 6 Open the filter access door at the
7. bag or pillow V Check there are no coins hair dips in the laundry and empty all pockets V Tum off the washing machine after each wash program and switch it off at the mains to save electricity and for safety Wipe dean the lower part of the porthole M Keep the door slightly open when the washing machine is not in use to prevent formation of odours v Ensure the power cable is replaced by the manufacturer his service agent or other qualified persons if it is damaged v Ensure that the washing machine is not used by persons with reduced physical sensory or mental capabilities lack of experience and knowledge without supervision or instruction by a person responsible for their safety Mv Supervise children to ensure that they do not play with the washing machine DO NOT VA Touch or use the washing machine when barefoot or with wet or damp hands or feet Make sure that the fuses in the power circuit are rated for 13A ya Use flammable detergent or dry cleaning agents Use any flammable sprays in dose vicinity to the washing machine vi Remove or insert the plug in the presence of flammable gas vi Allow children or intirm persons to play with the appliance or packing materials yi Install the washing machine outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit In the event of a water leak allow the mach
8. the back cover 2 Remove the four bolts on the rear side and take out the synthetic stabilisers trom within the machine 3 Replace the back cover 4 Fill the holes left by the bolts with blanking plugs Note 1 When you replace the back cover the convex surface must face to outside and you have to insert the back cover In the two slots as shown in fig 5 2 Keep the transportation bolts and synthetic stabilisers in a safe place for later use ADJUSTING THE WASHING MACHINE There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimise vibrations and thus noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance The floor should be as stable and flat as possible INLET HOSE Connect the nut on the inlet hose to the connector on the water valve 2 Apply inlet hose to a water tap with cold fresh water Note Use the hose set supplied with the appliance Old hose sets should not be reused DRAIN HOSE 1 Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water Don t extend the length of the drain hose if an extended hose is required please consult a serviceman 80 100cm 2 The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off
9. very good result already in lower CARE CHART Resistant material Delicate fabric Washable at 95 C Washable at 60 C Washable at 40 C Washable at 30 C Hand wash OOOK Bi Bi MRE LOAD REFERENCE Ded sheet single Cotton Blanket Wool Blended fabric clothes I Jackets Cotton Jeans Overalls Cotton Ladies Pyjamas i Shirts Socks Blended fabrics T Shirts Cotton Underwear Blended fabrics Bleachable in cold water Do not bleach Iron at 200 C Iron at 150 C Iron at 100 C Don t iron Dry cleaning with any solvent Dry cleaning with pericloride x Don t dry clean Dry flat I Hung to dry m Dry on clothes hanger Q Tumble dry reduced heat S Don t tumble dry Tumble dry normal heat Dry deaning with aviation fuel Approximately 800g Approximately 3000g Approximately 800g Approximately 800g Approximately 800g Approximately 950g Approximately 200g Approximately 300g Approximately 50g Approximately 300g Approximately 70g CLEANING amp CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash Open the washer door to prevent formation of moisture and odours If the washing machine is left idle for a long period drain the water in the machine and replace the drain hose CLEANING THE DETERGENT DRAWER Clean the detergent distribution drawer regularly Swing out the drawer flush it clean with water and then replace it CLEANING
10. AUTOMATIC DRUM WASHING MACHINE USER MANUAL HW80 B1 486 HW80 B1 286 HW70 B 1480 HW60 B1 286 S sien BEFORE USE USING THE APPLIANCE MAINTENANCE gt COMPONENTS 03 PROGRAM SELECTION 12 gt DISPLAY 60 aes 2 PT REPARATIUN scenes 04 CONSUMPTION AND TECHNICAL DATA 14 PTROUBLESHOOTING 22 gt SAFETY INSTRUCTIONS 05 WASHING METHODS l5 2 NSTALLATI N 06 gt CLEANING amp CARE 19 gt CONTROL PANEL 08 LEGEND v Yes VA No Optional For your safety any instructions in this manual with this Warning sign must be followed strictly DISPOSAL As a responsible manufacturer we care about the environment As such we urge you to follow the correct disposal procedure for your product and packaging materials This will help conserve natural recourses and ensure that it is recycled in a manner that protects health and the environment You must dispose of this product and its packaging according to local laws and regulations Because this product contains electronic components the product and its accessories must be disposed of separately from household waste when the product reaches its end of life Contact your local authority to learn about disposal and recycling The product and packaging should be taken to your local collection point for recycling
11. L Jeans c v LI LA Cotton or synthetic VA VA VA None Optional 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives Preset spin speed 800 rpm 600 rpm 800 rpm 1000 rpm 1000 rpm 1000 rpm 1000 rpm 800 rpm 800 rpm 1000 rpm 1000 rpm 1000 rpm CONSUMPTION TABLE MAX LOAD PROGRAM HW80 86 HW70 86 HW60 86 5 Hand Wash 2 kg 2 kg Tkg 3 Wool 2 kg 2 kg Tkq Delicate 2 kg 2 kg Tkg 5 Mix 5 kg 5 kg 3kg 3 Synthetic 4 kg 3 5kg 3kg Cotton 0 kg 7kg 6kg Daily Wash 4 kg 3 5kg 3kg 3 Sport 25 4 kg 3 5kg 3kg 3 Express 15 2 kg 2kg lkg Jeans 4 kg 3 5kg 3kq Baby Care 4 kg 3 5kg 3kg Spin Drain WASHING TIME TEMPERATURE 30 C 0 38 30 C 0 35 30 C 0 38 40 C Auto 40 Auto 60 C Auto 40 C 0 4 30 C 0 25 Pt 0 15 40 C 0 58 80 C leas 0 08 SPIN DRYING PERFORMANCE HW80 86 HW70 86 HW60 86 53 EN CO The standard 60 C and 40 C cotton programmes are suitable to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumptions for washing that type of cotton laundry The actual water temperature may differ from the declared cycle temperature TECHNICAL DATA Power source Max working current A Water pressure MPa Nominal load kg Spinning speed r min Washing programs Max power W Dimensions HxDXW mm Net weight kg Po
12. OVING THE MACHINE If the machine is to be moved to a distant location replace the transportation bolts removed before installation to prevent da mage as shown below Bmove the back cover Bmove the blanking plugs Insert the synthetic stabilisers and the transportation bolts Tighten the bolts with a spanner Bplace the back cover LONG PERIODS OF DISUSE If the washing machine is left idle for a long period pull out the electrical plug and turn off the water supply Open the was her door to prevent formation of moisture and odours Let the door open while not used a ROO n DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err Door is not properly shut _ Shut the door properly and then press the Start Pause button Err Drainage error water not emptied within 6 Clean the filter and check the drain hose for blockage If error minutes still exists please contact the maintenance personnel Err3 Temperature sensor not properly connected or _ Contact the maintenance personnel damaged Err4 Heater error Appears at the end of a cyde _ Contact the maintenance personnel Err5 Water level not met in 8 minutes _ Make sure that tap is turned on and water pressure is normal If problem still exists please contact the maintenance personnel _ Install drain hose within 80 100 cm of height The height of the drain hose is below 80 cm Make sure the dr
13. ain hose is not in water The drain hose is in water Err Motor error _ Contact the maintenance personnel Er8 Water exceeds protective level _ Contact the maintenance personnel Er10 The signal of Water level sensor is wrong _ Contact the maintenance personnel EuAr The PBC and the motor cant t communicate _ Contact the maintenance personnel End End of wash cycle 1 25 The remaining time is 1 hour 25 minutes 19 30 Status information Preset time for delayed operation UNb After the last rinsing cycle finishes spinning fails completely due to unbalance of the laundry 3 Control panel lock function Press the Delay and the Start Pause buttons simultaneously for 3 seconds after starting a program It can no longer be changed by operating buttons or knobs To unlock press the Delay and Start Pause buttons again for 3 seconds 3Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the present settings will be saved and the preset operation will resume when the power is on again To cancel a program Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program Note During the spin process if too much foam is inspected in order to protect the motor the washing machine will eliminate the foam automatically the motor will stop and the drain pump will drain th
14. ash box This additional nh dM nhn MH function applies to cotton memory synthetic and Sport wash programs only Press Rinse Hold button to startup shutdown the crease resistant and soak function This feature is only selectable with the cotton synthetic Delicate Sport 25 and Jeans programs When the process runs the last rinse the washing machine does not pump the water out the clothes will remain soaking in water and the soak icon flashes the remaining wash time does not decreasing If you need to continue the process you can press Rinse Hold button or Start Pause button to cancel this function and the icon will disappear and the washing machine will continue to the wash program This feature and the End Delay function cannot be selected at the same time _ Press the Start pause button the washer will start and the indicator light remains on If this button is pressed when the washing machine is in operation the washing machine will pause and the indicator light will flash If the Start Pause button is pressed followed by the Power button the wash program is ended and the washing machine is switched off WASH PROGRAM OPTIONS PROGRAM WASH DURDTION NUMBER OF RINSE SPIN DURATION INTENSE FUNCTION MINUTES CYCLES MINUTES Hand Wash 5 90 0 9 1 4 No Wool 5 30 0 9 1 4 No Delicate 5 30 0 9 1 4 No Mix 5 50 0 9 4 7 Yes Synthetic 5 50 0 9 4 7 Yes Cotton 5 60 0 9 4 7 Ye
15. bottom of cabinet you can see a ring pull handle amp ntly pull the sprung loaded handle down and pull the door at the same time to open it 7 fu can add or remove the clothing Caution the clothing will be very wet 8 Close the filter door MAINTENANCE OR SERVICE WASH A maintenance wash is recommended to be done to clean the washing machine out by running a high temperature 90 Cotton program This is especially recommended if you do a significant number ot low temperature washes a month The high temperature kills off bacteria and unwanted tungal growth A service or maintenance wash involves putting the washing machine on the hottest wash 90 Cotton Wash with only the detergent inside and no laundry If you normally use a washing machine detergent that doesnt contain bleach then buy some detergent that does and use it for your maintenance washes This will help kill off bacteria and prevent black mould and grease Tip Look tor something like bleaching agents in the ingredients Do not put cleaning bleach like Domestos in the washing machine this will damage the machine There are certain types of bleach example oxygen bleaches like fhish that are appropriate for laundry To check if your washing machine is being badly affected carefully examine the inside of the door seal for slime Pull the lip in front of the drum and look underneath on lip of the tub as it can accumulate a slime which causes smells and rots the seal M
16. e water continuously for 90 seconds If it happens more than 3 times the motor will stop until the end of cycle without spinning TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems Do not contact the Service Center until the problem has been confirmed PROBLEM Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cyde Operation stops for a period of time Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time Spinning fails CAUSES SOLUTIONS 3 Poor connection to the power supply _ Check connection to the power supply Power failure _ Check the power supply The washer door is not properly closed Close the washer door properly Machine has not been switched on _ Make sure the machine is switched on The Start Pouse button is not pressed _ press the Start Pause button Water tap is not turned on Turn on the water tap 3 Water pressure is less than 0 03 MPa _ Check water pressure The inlet hose is kinked Check the inlet hose Water supply failure _ Ensure the water supply The program knob is not properly set _ Set the program knob properly The washer door is not properly closed _ Close the washer door prop
17. erly The inlet hose filter is blocked Unblock the inlet hose filter The height of the drain hose is below 80 cm Install drain hose within 80 100 cm of height The drain hose is in water Make sure the drain hose is not in water Drain hose is blocked Unblock the drain hose Drain hose end is higher than 100 cm above Make sure the drain hose end is lower than the floor level 100 cm above floor level The filter is blocked Unblock the filter Not all transportation bolts have been removed _ Remove all transportation bolts 3 Washing machine is located on an uneven Make sure the washing machine is on surtace or is not level an even surface and levelled 3 Machine load is over Max load Reduce amount of laundry in the drum Water or electricity failure _ Check the power supply 3 Washing machine gives an error message Check display codes Washing machine is in soaking cycle __ Press the rinse hood button or the Start pause button again to cancel it The detergent is not a low foaming type or for Check if your detergent is appropriate manual wash _ Reduce amount of detergent in the distribution 3 Excessive use of detergent drawer The washing program duration will be adjusted _ This is normal and doesn t affect the functionality Unbalance of the laundry _ Add clothes or run a spinning program again INSTALLATION Electrical connection Any electrical work t
18. es the Intense function is selected This additional function applies to cotton memory synthetic Silent heavy and Sport wash programs only This button must be pressed before starting a program _Press the End Delay button and the illuminated icon indicates that the delay function is selected The delay time increased by 30 minutes each press of Delay button The time will change continuously if you press button until you release it The delay time is the end time of wash program For example 6 00 means the atter 6 hours the washing machine will have started after a delay and completed the selected wash program in 6 hours Note 1 The delay time must be longer than the program s running time The Delay function is not available for Spin Drain program Note 2 The delay time must be longer than the program time otherwise the washing machine starts the wash program immediately M Pre Wash N Rinse Hold 0 Start Pause Button Press the Pre wash button to select or cancel the prewash program The prewash program can be selected for washing heavily soiled clothes Press the Prewash button the Pre wash icon will illuminate Press the Pre wash again the prewash function will be cancelled and the Pre wash icon will go out When selecting the prewash function add a proper amount of detergent into the prewash box otherwise do not add any detergent into the prew
19. hat is required AN to install this washing machine MUST be carried out by a qualified electrician Warning THIS APPLIANCE MUST BE EARTHED Before making any electrical connections ensure that e Ensure the power socket is suitable for the maximum power of the washing machine fuses in the power circuit must be 13 amp e The supply voltage should be the same as that indicated in the technical specifications and the appliance rating plate located where shown e The appliance should be earthed and in compliance with the applicable law e Additional earth cables should not be necessary if the plug and socket are earthed If necessary an additional earth cable should be attached to the earth terminal on the back of the washing machine and earthed e When installed the power socket must be within easy reach e The use of adapters multiple connectors or extension cables are not recommended e The appliance must be connected to a 220 240 volt 50 cycle AC supply by means of a three pin socket suitably earthed and protected by a 13 amp fuse e Should the fuse need to be replaced a 13 amp fuse approved to BS1363 A must be used e The plug contains a removable fuse cover that must be refitted when the fuse is replaced If the fuse cover is lost or damaged the plug must not be used until a replacement cover has been fitted or the plug is replaced A damaged plug should be cut off as close to the plug b
20. ii D LAN OOOO O SELECTING FUNCTIONAL Select the required options Refer to the Control panel pages 08 and 10 SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected See Opera tional functions on the Control panel pages 08 and 10 for selecting temperature and spin speed It is advisable to select the recommended value WASHING Press the Start Pause button The washing machine will operate according to the preset programs The washing machine will stop operation automatically when a washing cycle ends The End sign will appear on the display Open the washer door and take out the laundry AFTER WASHING Turn off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odours Let the door open while not used TIPS FOR SAVING ENERGY Collect clothes for one full wash load Avoid overloading the washing machine Prewash only heavily soiled clothes Un RR N m than 60 C Only use higher temperature than 60 C for heavily soiled laundry 6 Follow the dosage recommendation on the detergent package to avoid using too much detergent Reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes Choose a proper washing temperature Modern detergents can wash with
21. ine to dry naturally i Place the washing machine directly on a carpet or dose to a wall or furniture DO NOT i Touch the washing machine door during the washing process it can get hot vi Place objects or sources of heat or damp on top of the appliance Hot wash foam rubber or sponge like materials Open the soap detergent distribution drawer during the wash cycle vi Force the washer door open during the wash cycle The door is fitted with a self locking device The door will unlock and can be opened shortly after the wash program has ended yi Open the washer door if the water level is visibly over the porthole vi Cover the washing machine with plastic cover so that condensation inside the machine cannot escape INSTALLATION ADJUSTING THE BOTTOM COVER Before removing the transportation bolts please fix the bottom cover to the bottom of the washing machine Lay down the machine fig 1 screw off the feet and adjust the bottom cover with the four holes corresponding the screw holes of the feet Then screw the feet back on through the cover and fix it thus securely to the bottom of the machine fig 2 It keeps out the dampness and reduces the noise DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti vibration components inside of the washing machine during the transportation process Remove
22. ody as possible the fuse should be removed and the plug disposed of safely Plug replacement UK amp Ireland only Should you need to replace the plug the wires in the power cable are coloured in the following way Blue Neutral N Brown Live L Green amp Yellow Earth E As the colours of the wires in the power cable may not correspond with the coloured markings identifying the terminals in your plug and proceed as follows The green amp yellow wire must be connected to the terminal in the plug that is marked with the letter E or by the earth symbol The blue wire must be connected to the terminal that is marked with the letter N The brown wire must be connected to the terminal that is marked with the letter L If the power lead is damaged it must be replaced by a qualified electrician Connect green yellow lead to E or Earth Connect brown lead to L Live J r JE VE Connect blue ead tas to N Neutral
23. rments without hems underwear finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them in a washing machine lose zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Unfold large pieces of fabric such as bed sheets bedspreads etc Turn shirts inside out LOADING THE MACHINE Open the washer door put in the laundry piece by piece Close the door tightly When first using the washing machine let it run unloaded for one program to prevent the laundry from being fainted by oil or dirty water from the washing machine Before washing you should run the machine without laundry but with detergent with 60 C programm Do not overload the washing machine SELECTING DETERGENT L 1 The washing efficiency and the performance is determined by the quality of detergent used Special non foaming detergent produces good washing results Use specific detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products Note Do not add more detergent than needed otherwise it may cause the situations as following and wash ing machine malfunction impacting washing machine s life 1 Due to the increasing foam the rinse time will be longer than normal 2 The foam may overflow from the detergent drawer because of the increasing pressure of the foam
24. s Daily wash 5 40 0 9 4 7 Yes Sport 25 40 0 9 14 Yes Express 15 5 20 9 1 4 No Jeans 5 40 0 9 4 7 Yes Baby Care 5 50 0 9 4 7 No Spin Drain 4 7 No AUTO WEIGH FUNCTION Auto weigh is a feature that is available for the Cotton Synthetic and Mix wash programs When the AUTO feature is selected the washing machine will rotate the drum at the beginning of the wash cycle before the water is added to determine the approximate weight of the dry laundry The computer in the washing machine then will adjust the quantity of water required to wash the laundry It is not recommended that the AUTO feature is used with liquid soap if the liquid is placed in the drum with the dry laundry The liquid soap will be tipped on the dry laundry during the drum rotation weighing phase and may damage the laundry The auto weigh feature is not recommended with very absorbent laundry like duvets or blankets If the auto weigh function is not required press the Wash or Rinse or Spin buttons to cancel the auto weigh function PROGRAM SELECTION QUICK START GUIDE 1 Open door and put laundry in drum checking that there are no coin clips paper tissues or sharp objects in the clothing 2 If using liquid detergent place the detergent in the manufactures recommended container in the drum Note Do not use the auto weigh tunction with liquid detergent it may spoil the cloths 3 0pen soap drawer and fill with soap powder and fabric conditioner as required Do not u
25. se more than the manufactures recommended amount 4 Close the door 5 Turn on water and electrical power if not already on 6 Press the Power button to switch on the washing machine 7 Select the wash program by turning program knob or press Memo button if custom wash has been previously saved 8 If selecting Cotton Synthetic or Mix wash programs the washing machine default to the AUTO weigh program If auto weigh is not required e g using liquid detergent press the Wash or Rinse or Spin buttons to cancel the auto weigh function 9 Change temperature spin speed spin duration any delayed start etc as required see BUTTON OPERATION FUNCTIONS section of this manual for details 10 Press Start Pause button to start the wash program PROGRAM SELECTION PROGRAM MODES Temperature Program Maximum 1 Hand Wash to 40 C 2 Wool to 40 C 3 Delicate t0 40 C 4 Mix 1o 40 C 5 Synthetic to 60 C 6 otton to 90 C Daily Wash to 60 C 8 39pot25 to 40 C 9 Express 15 to 40 C 10 Jeans to 60 C 11 Baby Core to 90 C 12 Spin Drain v Ys p No Recommended Preset 2 3 Loundry 30 C lV i Cotton fabrics xc vA L VA Woolen fabrics 30 C DT O VA Cotton fabrics 40 C v C Cotton or synthetic o Chemical fiber ih iv L fabrics 60 C Iv Cotton fabrics c v C VA Cotton fabrics 30 C lv VA Sports wear v D W Cotton or synthetic AU v
26. ue to technical improvements Control panel Drain hose Power Water inlet valve Work top Door handle Power cord Washer door Back cover screws Detergent distribution drawer Back cover Filter cover Transportation bolts Nator SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO Make sure that the transport bolts are removed before use Make sure that all packing materials have been removed Use a separate earthed socket for the power supply Make sure that the plug is accessible Hold the plug and not the electric cable whenplugging in unplugging the power supply IN ESTIS UST SI M Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging V Make sure that the power cable is not caught or trapped under or in the machine to avoid damage to the power cable LV Check that hose joins and connections are secure and there are no water leaks If joints are loose or there is a leak turn off the water supply and tighten or remake the connections to stop the leak Do not use the washing machine until the hoses are properly secured and free of any water leaks V Check the water inlet or drain hoses are not folded trapped or kinked DURING DAILY USE OF THE APPLIANCE DO V Pull up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a net
27. wer consumption of the off mode W Power consumption of the left on mode W HW80 B1286 B1486 220 240V S0Hz 10 0 03 lt P lt 0 1200 1400 12 2000 850 X 650 X 595 4 0 39 0 39 HW70 B1486 220 240V 50Hz 10 0 03 lt P lt 1400 12 2000 850 X 600 X 595 0 0 39 0 39 HW60 B1286 220 240V 50Hz 10 0 03 lt P lt 6 1200 12 2000 850 X 520 X 595 65 0 4 0 40 ASHING METHODS This washing machine is for domestic use only If the machine is use for commercial purpose the guarantee will not be valid anymore Do not use it for purposes other than that for which it was designed Follow the instructions given on the label of each garment and wash only machine washable garments POWER SUPPLY Connect the washing machine to the power supply 220V to 240V 50Hz WATER CONNECTION Turn on the tap The water must be clean and clear Note Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap PREPARING THE LAUNDRY 3 Sort out clothes according to fabric cotton synthetics wool or silk and to how dirty they are 3 Separate white clothes from coloured ones Wash them first by hand to check if they fade or run Empty pockets keys coins etc and remove the harder decorative objects e g brooches Attention Small parts like buttons etc may lead to repair work which user has to pay by themselves and can cause damage in the machine Ga
Download Pdf Manuals
Related Search