Haier FCD-JTSA60-III User's Manual
Contents
1. A Adjust temperature of water nly cold water but pointer light Heating time limit and setting e when heat temperature not obtain D Defective heater Contact with service department when 1 are excluded Only cold water No power to heater Check power socket and pointer not Contact with service department Uncontrollable thermostat a when Dis excluded Setting water temperature not 9 p Keep heating Heating pointer obtain always light Uncontrollable thermostat Contact with service department when 1 is excluded Adjust the flux of outlet water or use with constant water pressure Unconstant flow and Unconstant water pressure temperature of water Insufficient hot 1 Temperature set too low Adjust setting water temperature water 2 Excessive water pressure Adjust the flux of outlet water iti Packing List Electric Safety User s Expansion Expansion Name Drain hose water heater valve manual hook bolt 62. necessary The hose shall be installed as inclined downward This product should work with the safety valve whose rated pressure is 0 75MPa The water may drip from the discharge pipe of the pressure relief device and that this pipe must be left open to the atmosphere Check safety valve once a month as follow move the small handle of safety valve if there s water flowing out safety valve is normal if there s no water flow please contact local after sales service station The pressure relief device is to be operated regularly to remove lime deposits and to verify that it is not blocked 4 Cleaning and Maintenance Be sure to switch off the power supply before cleaning Use humid cloth with neutral detergent to wipe the shell gently Do not use petrol and other solvent Finally wipe it with dry cloth and keep the shell dry To guarantee the high efficiency operating of the water heater please clean the electric heating pipe and inner tank every three years Do not damage the protection coating outside the electric heating element and inside the inner tank The Magnesium anode rod shall also be replaced periodically according to the local water quality Please contact the local maintenance department for maintenance service FAQ No water supply or water D ppy Check No water pressure too low 2 Hot water access close Check and clear C Hot water access close Check and open Temperature not set to desired oniveoid
3. 0040502744 Haier y E Before Usage Dear users Thanks for choosing Haier water heater product Haier products have good quality and excellent performance To facilitate you to use the product please read the manual and operate accordingly Please retain it for future reference The international star service of Haier Group will always accompany you No matter what kind of problems you meet in usage please contact with the local after sales service agent We are at your service all the time Thanks again for choosing Haier Product The water heater you purchased may not full comply with the figure in the manual due to the improvement of product We apologize for the inconvenience occurred therefrom Features 1 Safety High quality heat proof stainless steel electric heating element overtemperature protection overpressure protection of tank safe and reliable The 3rd generation PTO 10 technology safer for usage 2 Durability The shell adopts dusting anticorrosion treatment handsome and durable enamel tank with reliable quality and long operation life 3 Convenience Adjustable heating temperature Adjustable water temperature Adjusting range water inlet temperature 75 C 4 Multiple usage Enclosed structure capable of supplying water to multiple places like toilet kitchen etc Suitable for family enterprises service trades like beauty care on hot water supply not drinkable 5 Nice molding space saving Ve
4. ater can be led to the sewer The drain hose connecting to the safety valve shall be kept downward sloping in installation and in a frost free environment Connect to drain hose Figure 3 Select suitable position on the wall to fix the shower nozzle bearer Connect the shower nozzle hose to the pipeline Fasten the mixing valve Check if there s water leakage at each joint Be sure to check and confirm that the tank is filled with water there s no leakage at each joint and the power supply complies with the stipulation before switching on the power Safety precaution Do not confuse the water inlet and outlet pipe The wall bearing the water heater shall be strong enough to endure a weight twice as much as that of water heater filled with water If any part is damaged please contact the local maintenance agent and have it replaced with our spare part sl Usage After installation as the tank is empty in the first usage be sure to open the faucet water inlet valve and mixing valve When the tank is filled with water and the shower nozzle or other water outlet keeps water outputting please close the mixing valve check if there s water leakage at each joint and plug the power plug Turn the knob as per the needed water temperature The mark of knob increases from water inlet temperature to 75 C You can set heating temperature steplessly The heating indicator will light on under heating mode Generally the kno
5. b should be set to the highest scale The water heater can regulate the temperature automatically The power will be switched off automatically when the set temperature is reached and will be switched on automatically when the temperature drops to certain level As it continues heating you can use hot water as well When the tap water inlet pressure arrives or exceeds 0 75MPa the drain hose of safety valve will discharge large amount of water It is due to extra high water pressure Please contact the local after service for disposal Heating adjustment can be made flexibly all year round adapting to climate changes In long term out of use or maintenance you can close tap water pipe valve and set the mixing valve to the highest water temperature rate after opening the safety valve handle Move up safety valve handle to drain the tank To avoid injury before next use it is suggested to first open hot water valve before switching on the water heater exhausting gas possibly retained in the pipeline In this case no smoke or fire is permitted near the open valve Carefully check and confirm all parts are in good condition Installation Be sure to have it installed by installation staff of the after service department or the appointed staff It adopts wall mounting installation Make four holes with diameter of 12mm and depth 65mm with churn drill on the wall as per the installation dimension drawing Insert the bolts into t
6. ccordance with receptacle and earth it reliably The the rated current of the water heater receptacle shall comply with the If necessary please have it checked by stipulation of national standard experienced electrician Set the receptacle of the water S heater at dry position away from water spraying Do not insert and pull the power plug with wet hands O Check if the ammeter and the diameter Q Be sure to use independent The product is only available for alternating current After installation be sure to fill the heater completely with water before switching on the power in the first usage Children must take bath under the supervision of adult In opening and closing the water valve do not point the shower head to human body Otherwise it may hurt by the spraying hot water In case the power cord of the water heater is damaged be sure to have it replaced by after service technicians with special cord offered by the manufacturer In winter of cold area if the heater is idle for a long period please pull the O handle of safety valve to discharge the water Otherwise it may freeze inside the water heater and cause damages The product adopts the patent PTO I 0 technology of our company As long as adopting civil power supply even if the earthing wire is electrified by mistake the PTO 0 technology still can block the dangerous electricity and ensure your personal safety But if you find perceptible curren
7. he holes Then lift the water heater set the wall mounting rack on the bolt Set the gasket and fasten the nut Install the accessories including safety valve etc as indicated in Figure 2 Remember to seal with rubber tape to avoid water leakage To facilitate the installation and dismantling it is suggested to add G 1 2 flexible nut at the suitable position of the water inlet and outlet pipe separately Confirm the position needing water supply Connect the water inlet outlet pipe and tap water pipe to the position respectively The hot water pipe shall not be too long to reduce the heat losses Please reserve some space in installation for the future maintenance Figure 2 For reference in installation only Cold water Hot water outlet outlet valve valve Mixing valve Connection and use of safety valve The safety valve should be connected to the cold water inlet pipe Please check carefully if the direction is correct after installation The correct direction of installation is that the arrowhead on the safety valve should point to the water heater Please connect the drain hose to the safety valve Connect one end of the hose to the safety valve vent and the other end to the sewage drain The hose can be cut short or extended as
8. rtical type wall mounting design saving space The water heater you purchased is the improved model of the series product Please operate according to the user s manual i Parameters Rated voltage Rated Rated Waterproof Dimension Toniou Frequency power pressure grade Weight Volume j p 220V 50Hz 1500W 0 75MPa IPX4 See to Figure 1 no less than 0 05MPa 220V 50Hz 1800W 0 75MPa IPX4 See to Figure 1 no less than 0 05MPa 230V 50Hz 1650W 0 75MPa IPX4 See to Figure 1 no less than 0 05MPa 230V 60Hz 1650W 0 75MPa IPX4 See to Figure 1 no less than 0 05MPa All the rated power mentioned above are available for this model More details please refer to the nameplate 1 Haler Little Sea ox Haier Household Electric Water Heater FCD JTSA50 III FCD JTSA60 III FCD JTSA70 III FCD JTSA80 III SSE I EE ee 2 Please read this manual before usage Retain it for future reference Dimension Figure 1 Front view Cutaway view Bottom view Le a1 J d1 A Hot water outlet B Cold water inlet C Heating element b1 D Enamel tank E Wall mounting bracket ae Sl AES ome oc weight Remarks The permitted error limit of above parameters is 10 Electric Circuit Diagram L Brown wire MT BT N Blue wire MT High temperature limiter L BT Thermostat HL Heating indicator EH Heating element E Yellow green wire Safety Precautions of the wires are in a
9. t please pull off the power plug and contact local after service department for maintenance Do not disassemble by yourself Description of the Symbols S Never do that O Be sure to act as per instructions ial Setting Environment S Do not set at outdoor places Please mount it to firm and reliable wall S Do not set it at place where is too cold and may freeze Do not use as floorstanding appliance Do not install to places without sewer In case connecting water heater with water drain hose connect the drain hose to the inlet of the sewer to avoid polluting by splashing O The original pipeline of the water heater is an organic part of PTO 0 Do not remove it by yourself Otherwise we will not take responsibility for the injure and loss caused by the safety trouble occurred therefrom Description of the Symbols S Never do that Q Be sure to act as per instructions E Attentions in Installation Please fasten the drain hose to the drain thread of safety valve by twisting see to Figure 3 Connect the other end of drain hose to the sewer to avoid polluting the room by splashing When the power is switched on and the water heater starts operating there may be some water discharged from the pressure relief hole of safety valve It is due to the water expansion under heating and is normal phenomenon The pressure relief pipe shall communicate with the air directly Do not block it The discharged w
Download Pdf Manuals
Related Search