Haier HW-05LMA13 User's Manual
Contents
1. Avoid opening doors and windows unless necessary a long time Air inlet outdoor side 2 Airflow Direction Use curtain or blind Direct sunlight may reduce cooling effect always use window curtain air conditioner It is advisable to clean air filter every two weeks for Don t be exposed to cold air for Keep heat source away from Switch off the power supply if the unit is not going to be used for a long period of time Set temp alittle bit higher before going to bed Proper temperature e After unit stops don t restart it until 3 min have elapsed A OK Enjoy a 3 min nap ey The air directional louvers let you control the direction of the airflow The airflow can be directed left to right Don t hang clothes in the vicinity of air inlet This will decrease cooling effect and cause abnormal operation Temperature should be set properly when there are infant child the aged or disabled in the room e Before operating mode selection switch check that if the air inlet or outlet have been blocked Ox CORR KKK SSL SOR m Ba SB Spee aba aha aw L NI LDN E Y L 4 AIR CONDITIONER INSTALLATION omyrorrererenct 5S TROUBLESHOOTING Before calling for service SELECTION OF THE INSTALLATION POSITION Check the following points before calling for repairs or service 1 The air conditioner is better installed i2. DB WB Note e Do not try to operate your air conditioner in the Cool mode when outside temperature is below 18 C The inside evaporator coil will freeze up and the air conditioner will not Cooling W B Wet Bulb Temperature D B Dry Bulb Temperature 2 AIR CONDITIONER OPERATION PART INDENTIFICATION operate properly 3 CARE AND MAINTENANCE Always turn off the air conditioner and the main power supply before clean the unit Machine body Front panel Air outlet indoor side Air inlet indoor side Air filter inside Operation panel Power plug DL i I 1 Air filter cleaning When dirt accumulates on air filter air the power circulation will be blocked which causes poor cooling It is advisable to clean air filter every two weeks for longer operation 1 Turn off the air conditioner 2 Grasp the filter handle and pull the filter out The filter will slide out easily 3 Gently flap the dirt off the air filter Carefully wash air filter in warm water below 40 C To obtain better cleaning effect soap water or neutral detergent may be used 5 Flush air filter carefully with clean water after removing dirt Let it dry completely A Common Before cleaning turn off A 1 Air filter cleaning Machine body longer operation You will find how to clean the filter on page 2 2 Notes
3. AN CAUTION In cooling mode after you turn thermostat switch counter clockwise do not turn it back until at least 3 minutes have elapsed Otherwise the fuse may blow due to overload Do not exceed the selection range ROOM AIR CONDITIONER OPERATION MANUAL Operation panel Haier HW 05LMA13 5 6 4 7 3 8 2 9 1 10 Please read this operation manual before using the air conditioner i j MIN MAX Please keep it attentively oai 0010563803 COOL FAN ONLY CONTENTS a Tr Safety precautions 1 D Air conditioner operation 2 Care and Maintenance 4 BOWER Air conditioner installation 5 Troubleshooting 7 EE Wait 3 Minutes Before Restarting 1 SAFETY PRECAUTION A e Do not install remove and reinstall the unit yourself Improper installation may cause leakage electric shock or fire Please engage an authorized dealer or specialist for the installation work 2 Mode selection switch The room air conditioner must be earthed n Temp setting POWER Do not touch or operate with wet hands The Power switch turns the air conditioner on or off e Do not turn on the unit by inserting the power plug Do not switch off the unit by pulling out NORMAL FAN 1 Therm ostat switch Press the SPEED switch to either HI or LOW Set the thermostat control to the FAN ONLY setting NORMAL COOL Press the SPEED switch to either HI or LOW Set the thermostat control to the des
4. e leaking of the coolness 4 After installation of the conditioner insert the power plug into the outlet and perform test run Cautions Power cord Be sure to use the exclusive power cord Change installation place If air con need to be changed to another A N place please contact the dealer who sold you the unit e Always use at the rated voltage and with specfic air conditioning circuit
5. g Install air con at a place strong enough to support the unit Is there any direct Use curtain or blind Leave enough space around air inlet and outlet for better circulation sunlight in the room Avoid places where flammable gas leaks Problems may occur if unit is installed in the following places Place where oil exists in the air including engine oil or seaside with Are doors or windows salt breeze blows and hot spring area with sulphurous gas in the air 7 left open anui doars and Windows The cooling effect is not good THE ENCLOSED ACCESSORIES OF THE CONDITIONER so Are there any obstacles Remove the obstacles blocking air inlet and outlet Clean it Is air filter clogged 2 ALS pp Is there too much heat source in the room Remove the heat source PREPARATIONS BEFORE INSTALLATION If problems can not be solved please pull out power plug and contact Make the wall hole or window hole see Fig 1 your dealer lron frame MODEL A B Width of the wall Pa Fig 1 Prepare unit for installation Take out the conditioner and accessories from the package INSTALLATION PROCEDURES 1 Fix the prefabricated iron frame to stable position by expansible screws 2 Put the whole machine with all the accessories installed on the iron frame 3 Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and th
6. ired temperature setting If the room is not satisfactory after a reasonable amount of time adjust the thermostat control to the appropriate setting to meet your needs MAX COOL Press the SPEED switch to HI Set the thermostat control to MAX COOL mark QUIETER OPERATION Press the SPEED switch to LOW Set the thermostat control as needed the power plug e Do not insert sticks fingers or other objects into the unit e f the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person e After installation the power plug should be easily reached e The wiring method should be in line with the local wiring standard This air conditioner contains R410a refrigerant and requires certified technicians to use the proper equipment tools and safety standards that are approved for this refrigerant Use only equipment certified for R410a refrigerant In addition under federal law all refrigerant must be properly removed from the air conditioner prior to its disposal This switch controls the preset indoor temperature to make the air conditioner start or stop automatically so as to reduce power consumption and operate the system both comfortably and economi cally The compressor stops running when the set temperature is reached but the fan continues to operate to keep an even indoor temperature OPERATION CONDITIONS Applicable ambient temperature range Indoor D B WB
7. n shadow or in a place with short period of sunshine In case the air conditioner is installed at the point exposed directly to the sunshine it should Phenomenon Cause or check points Solution be protected from the direct sunlight as possible in order to avoid the long time of direct sunlight otherwise its performance will be lowered As illustrated in Fig 1 2 For the convenience of operation it is Switch on the machine but it If the machine is started after stop it will need about 3 minutes recommended that air conditioner be installed at Bees Hob WOTEIMMECIAEIY to re start so as to prevent the fuse from break least at the height of 760 1300 mm above the floor and no obstacles before it for a free airflow 3 The shutters at both sides and the top of l l l air conditioner should be protruded outdoors free Switch on the machine but it from being blocked by wall window ect 7 goes MCP wore 4 The back of air conditioner should be kept over 500mm from the obstacles for example wall etc As illustrated in Fig 2 5 To have an efficient drainage the back part of the air conditioner should be inclined downward by 5 10mm As illustrated in Fig 3 Is plug firmly inserted Readjust power supply Is there power failure Does fuse get burned Replace fuse fig 2 Is thermostat switch Readjust the thermostat NOTES wrongly adjusted For longer and trouble free operation of the unit pay special attention to the followin
Download Pdf Manuals
Related Search