Haier FCD-HTHMG50-III(E), User's Manual
Contents
1. City water inletpressure shall notbe less than0 05 Mpa QO Electric water heater shall be installed indoors with ambient temperature above 0C The pipes shallbe collectively laid Hot water outletshall not betoo far fromuse points In case farerthan 8 m hot water pipe shall have athermal insulation to minimize heat loss The mounting wall shall be firm and reliable to support twice the weight of water heater full of water Non load bearing walls or air brick walls must have corresponding protective measures like additional support wall throughscrews or back boards O Electric water heater shall be located in a place easy for use maintenance and witha floor drainer In case the tank or pipes leak nearby or lower facilities shall not be damaged The installation location shall avoid being above toilet bowl bathtub washbasin or doorframe where will causea suppressed orunsafe feeling tousers Power socket for water heater shall be in a dry place free of water splash to avoid nonnormal work ofthe water heater splash proof boxis preferred ODo not confuse inlet and outlet water pipes Safety valve shall be installed at designated position with no random modification The safety valve pressure relief vent shall keep opento the air Do notblock it OTo ensure safety water heater shall use aseparate socket not multi purpose socket and be reliably grounded Socket quality shall comply with local standard Check with a neo electroscope th2. In addition inregional power consumption regulations night power price rate islower than in day so Night Power mode willbe easier andmore economic Note In selecting Night Power function water heater clock shall be adjusted to local time Inaccurate clock will cause night period partly charged as day use Only for regions with Peakand Valley Electricity Rates Example With machine powered on press Mode button to select Night Power mode When PC clock displays 00 00 machine automatically starts heating It enters warm status after reaching setting value and has thermostat control during 0 00 6 00 see Fig 11 8 Intelligent Heating Function Intelligent heating function means that the system can analyze process and memorize user s water use habits in one week and accordingly heat water in advance automatically With machine powered on consecutively press Mode button until it enters Intelligent operation mode with intelligent indication lighted on System automatically starts heating in the first memorized heating time since then Heating power and highest temperature can be manuallyset In non heating period system remains standby with clock and intelligent indications lighted on After it reaches the heating temperature the machine will start to heat aotomatically If you d like to quit Intelligent Heating mode and enter another mode you can press any button on control panel to activate the interface buttons on remote controller in
3. Features Safe High quality imported heat resistant stainless steel heating element corrosion resistant and more reliable Fuzzy control with over temperature protection tank liner over pressure protection andcurrent leakage protection Safe Care patented design together with the function of monitoring and displaying of live ground wire has become a real safeguard for family safety Durable Specially treated shell Elegant and durable Tankliner produced with 3 layer liner enameling technology More reliable quality Energy Saving One piece PU foaming technology thermal insulative and power saving Two delayed water use times manually set easy and energy saving Three power levels Upper and lower heating elements Save energy in both winter and summer Night power feature and Medium temperature warming feature free selection as you desire Easy touse Water heating temperature adjustable between 35 75 C in an incrementof 1 C Outlet water temperature adjustable between inlettemperature and 75C Power Failure Memory Patented PC board design Machine automatically memorizes setting information before power failure and directly goes to previous working status upon power resumption Multi purpose Closed structure suitable to connect several outlets for water use in locations like washroom and kitchen outlet water isnot suitable to drink Horizontal installation space saving Options of localcontrol or r
4. heating element may be damaged Do ensure power socket complies with local standard andis reliably grounded Ungrounded useis forbidden O This electric water heater is provided with a safety valve which shall not be randomly relocated or blocked Hot water above 50 C may burn your skin Do mix hot water and cold water before showering or washing At an ambienttemperature below 0C possible ice formation within pipes may break the pipes and causethe machine inoperable Protection shall be made by emptying water in the tank Incase the water heater will notbe used for more than 1 month please empty the water andunplug the power plug O lf the electric water heater is heavily wetted by water it should be checked by our authorized technicians beforenext use Hot water inside the water heateris not drinkable Due to long time use sediments will form inside the tank and water quality may also deteriorate due to pipe aging After washing rice and vegetables with water from the tank please flush again with clean water O Please do notplace flammable matters like gasoline nearby the water heater otherwise accidents like fire may occur Features 1 High Technology Full PC controlled Display indicates the actual water temperature temperature setting clock and working state Upon faults power supply is automatically cut off and the display indicates fault code The intelligent heating feature reflects amore humanized design
5. Make sure power plug closely fits with power socket O For first use after installation the tank must be full of water before connecting the power Otherwise heating element overheat may cause troubles Children taking shower must be attended by adults O In winter in cold regions for long term out of use please liftthe safety valve handle to empty the water avoiding ice formation damaging the water heater KAS O Power socket for water heater shall be located in adry place free of water spray Do not insert or pull the power plug with wet hands for accidents like electric shock or injury may happen QO Please do not point the showerhead towards human body when turning on oroff the faucet avoiding to be scalded by a small stream of hot water O Damaged power cord must be replaced by after service technicians with special cable factory provided Other persons shall not dismantle or repair In addition do not place flammable matters nearby the water heater Temperature value indicated on the display is for water around the detection point Outlet water temperature is generally higher Before use please first turn on cold water and then adjust water temperature as youneed During use the displayed valueis still watertemperature at detection point instead of outlettemperature Please donot directly turnon hot water The product adopts Haier Safe Care patented technology In normal installation even in s
6. Silver Sea ox Haier Household Electric Water Heater User s Manual FCD JTHMG5O III E FCD JTHMG60 III E FCD JTHMG80 III E FCD JTHMG100 III E s Haier Group Qingdao Economic and Technological Development District Haier Water Heater Co Ltd Add Haier Garden Qianwangang Road Economic DevelopmentZone Qingdao P R China Website http www haier com i Rev 01 Please read this manual before usage Specific Number 0040501638 Retain it forfuture regerence Pre safe Expert This mark is the designation for Pre Safe Expert of Haier Water Heater Company which indicates use of the company s patented technology inside the f product It ensures you a safe bath while monitoring a e whether your house ground wire is live or not all the time If this mark is lighted on it indicates your house ground wire has come live poor grounding and live In this case please immediately stop use and unplug from the power supply and remember not to touch any electric appliance shell in your house At the same time immediately contact after sales service and your property management company for professional repair until the mark goes off Pre Safe Expert will become the electric safeguard for your family Care P PTOIO Mark of Haier Safe Water Heaters Contents Cleaning and Maintenance Statement This water heater shall only be repaired and maintained by qualified servicemen Improper maintenance may caus
7. active andthen press Mode button to shiftmodes Notes 1 Inany mode after powering on Intelligent Heating function can memorize your water use habits If you bathein a fixed period everyday severaltimes a week 4 times or more than 4times system willanalyze and memorize your this habitand automatically start heating inadvance 2 Only inIntelligent mode can Intelligent function be executed 2150W 2150W aoe emir 7570 eo 10 0 1 0 Fig 12 Fig 13 10 Operation Instructions 2 Temperature Setting With the machine powered on with no any digits flashing on the display press A or V button to enter temperature setting status with the temperature digits rapidly flashing Temperature can be changed between 35 75 C with an increment 1 C In real time heating mode you can directly press or V button to adjusttemperature setting value In medium warm status machine defaulted highest temperature is 40 C and can t be adjusted If actual water temperature is lower than setting value and the machine is in medium warm mode you need to change operation mode to real time heating mode and then the machinecan heat waterto the settemperature 3 Clock Calibration Clock goes in24 hour and 60 minsystem in asecond flashing way Example calibrate theclock to 11 29 After poweringon in real time heating and nightpower modes youcan press Setbutton to enter clock calibr
8. ation 1 2 3 4 5 6 7 89 10 11 12 13 850W 1300W 2150W A a a z J od Set A V HAE ha H T id psan Power On Off HE HR L pfn A 1817 16 1514 1 Set Button 10 Intelligent Indication 2 Temperature and Clock Time Increase Button 11 Mode Button 3 Temperature and Clock Time Decrease Button 12 Power Level Selection Button 4 Real time Heating Indication 13 On Off Button 5 Medium Warm Indication 14 Warm Keeping Indication 6 Night Power Indication 15 Time 2 Indication 7 Heating Power Indication Area 16 Clock Time Display 8 Heating Indication 17 Temp Setting ActualTemp Display 9 Delay Indication 18 Time 1 Indication 2S Signaling Indication 1 IndicationArea 1 a 2 Mode selection Button is Real time Heating Indication 3 Temperatureand Clock Time Increase Button a Medium Warm Indication 4 Set Button a 5 Temperature and Clock Time 8 ee Night Power Indication Decrease Button conti Ta 6 On Off Butt V Intelligent Indication j pe 1 7 5 7 Confirmation Button 6 A C oeny Indication 8 Power Level Selection Button Operation Instructions For the firstuse after installation due to there sno water withinthe tank firstthe city water inlet valve and mixing valve mustbe opened Close the mixing valve when water flows out continuously fr
9. ation status with hour digits flashing Press A or V button to set 11 Press Set button again and minute digits flash Press A or V button to set 29 You can press Set button to confirm current setting or wait 6 s after which the system will automatically confirms and quits setting status as shown inFig 7 machineis in real time heat warmmode 2150W 6 i 2 2 00 ice Fig 6 Fig 7 4 Power Level Selection With the machine powered on press Power button todirectly go to power level selection status You can selecta power level850 W 1300 W or2150 W If 850 Wis selected 850 W digits are lightedand only the upper heating elementworks If 1300 W is selected 1300 W digits are lighted and only the lower heating elementworks If 2150 W is selected 2150 W digits are lighted and both the upper and lower heating elements work In Delay mode machine defaulted heating power is 2150 W and can tbe adjusted Fig 8 shows a heating power level 2150W the present clock time 12 10 and thereal time heating mode La 5 Real time Heat Warm Setting With machine poweredon as describedin Item 10 press Mode buttonto enter Real time Heat Warm mode withreal time heat indicationlighted on According to settings machine will automatically starts to heat orkeep warm The machine has a thermostat function by which the machine goes into warm keeping status whenit reaches thetemperature setting value In warm keep
10. ay Relay Relay L Brown wire N Blue wire MT High temperature limiter EH Heating element RT ook RT Sensor E Yellow green wire EN amp 13 Before Usage Dear users Thanks for choosing Haier water heater product Haier products have good quality and excellent performance To facilitate youto use the product please read the manual and operate accordingly Please retain it for future reference The international star service of Haier Group will always accompany you No matter what kind ofproblems you meetin usage please contact with the local after sales service agent Weare at yourservice all the time Thanks again for choosing Haier Product The water heater you purchased may not full comply with the manual due to the improvement of product We apologize for the inconvenience occurred therefrom Special Reminding Toensure proper and safe use ofthe water heater we hereby sincerely declare thatusers shall contact our designated professional service providers for installation and service For inappropriate installation Haier would notundertake any liability O Do disconnect the power supply beforeany maintenance andrepair on the water heater Unprofessional persons shallnot adjust orrepair the water heater Make sure the machine is fullof water before powering it on otherwise
11. e line and neutral are not wrongly connected Only after confirming the tank is full of water no water leakage at various connections and power supply meets requirements powercan be turnedon to startheating 6 Installation Installation must be made by installers of or designated by our company after service department The water heatershall be wall mounted O Before installation make sure water heater rear wires are fit firmly Determine an installation location Make four holes 12mm 65 mm deep in the wall with an impact drill as shown in Fig 2 Insert and fixexpansion hooks and expansion bolts in corresponding wall holes Lift the waterheater Insertwall rack ontothe hooks and bolts Fit flat washers rear wires and nuts in turn onto the bolts see Fig 3 Tighten the nuts and check themfirm Install accessories such as safety valve drain hose as shown in Fig 4 Usesealing compound toprevent water leakage L1 A Capacity 50L 6OL 80L 100L L1 200mm 300mm 282mm 370mm L2 320mm 320mm 320mm 320mm Fig 2 Fig 3 O To facilitate installation and removal it is suggested a G 1 2 movable nutis fitted at appropriate locations oninlet and outlet pipes respectively Find water supply location Connect inlet pipe outlet pipe and city water pipe respectively to the use point Fillthe tank full of water and check if water circuit shows any leakage Fo
12. e severe injury or damage Before opening orrepairing water heater please dopull out the power plug Note Before asking for service please refer to troubleshooting section to resolve easy problems O External Cleaning Disconnect power supply before cleaning Gently wipe with wet cloth dipped witha little of mild detergent Do not use gasoline or other solvents Finally dry with dry cloth Keep water heater dry Do not use cleansers containing grinding agent e g toothpaste acids chemical solvents e g alcohol orpolishers to clean O Internal Cleaning To ensure high working efficiency heating elements and tank liner of water heater shall be cleaned oncein three years Take care notto damage protection layer on heating elements and tank liner inner surface According to different local water qualities and use habits magnesium anode rod shall be periodically replaced If maintenance is needed please contact localservice station FAQ Problems Possible Causes to be Confirmed Corrective Measures If water supply is stopped or water pressure is too low Check No outlet water If use point is blocked or if hot water i Check and clean valve is open Before USage Control panel illustration 6 8 Special reminding ceee 2 Remote controller panelillustration 8 Features 0 0 cece cece Epe igi cence 2 3 Operation instructions 8 12 Views apdparisee e c rrereesreirserissre 3 Operation diagram e
13. emote control Your water heater is an improved product of this series Please use it as instructed in this manual Views and parts Front View Cutaway View Side View Fr NI G E D S Y A B A Hotwater outlet B Cold water inlet C Heating element D Enamel tank E Waterinlet tube F Water outlettube G Magnesium anode rod H Wall mounting bracket Operation Instructions D In non heating intelligent mode machine stays in standby status You can activate interface by pressing any button onthe control panel buttons on remote controller are inactive Operation Diagram As V Set highest heat temperature m Clock hour setting Real time _Press Set button Heat Warm Clock minute setting Medium Warm Clock hour setting Power Mode i Press Set button Sh Function Night Power button Clock minute setting Press Set button Time 1 hour setting Press or Y Calibrate Time 1 hour digits Time ee L Time 1 minute setting PSSA Calibrate Time 1 minute digits On Off _ button m Time 2hour setting Press or V Calibrate Time 2 hour digits L Time 2 Press Set button l Time 2 minute setting Press or VYCalibrate Time 2 minute digits Time 1 Time 2 Press Set button Repeat steps for Time 1 and Time 2 Intelligent Power button Select heating power 850W 1300W 2150W Power off Attentions in Operation 1 Toavoid causing machinetroubles do notconnect
14. evere case that groundwire is live due to wrong connection the product Safe Care technology can filter and efficiently ensureyour safety However whenever your feel asensory current please pull out the power plug andnotify local after servicemen in time Do not dismantle by yourself Description of the Symbols OQ Never do that Q Be sure to act as per instructions Setting Environment Do not locate in freezing places If ice A forms tank and pipes will break causing Do not installit outdoors scalding and leakage O Do not installit as stand alone O It shall be hung on firmand solid wall Sho Ao O If a drain hose is connected it shall be O Do not installit in places unable to drain connected to sewage drain avoiding water spilling the room The tubes and pipes fitted on the product are inseparable parts of the Safe Care technology and shall not be removed by yourself Otherwise Haier shall not be liable for any damages orinjuries caused dueto resulted potential risks Description of the Symbols OQ Never do that Q Be sure to act as per instructions Parameters Rated voltage 230V 50Hz Power 850 W 1300 W 2150 W Rated pressure 0 75 Mpa Waterproof grade IPX 4 A Dimensions see to Fig 1 Weight see to Fig 1 Volume see to Fig 1 Tap water pressure not less than0 05 MPa Operation Instructions Water heater automatically sets an ene
15. g status these buttons canbe used toincrease or decreasetime Set button Pressit to setclock time andpress or V button to adjustthe value Press Confirm button after adjusting In Real time Heat Warm mode press Set button to adjust clock hour and minute together with Confirm button In Time 1 mode press Set button to setTime 1 hour and minute In Time 2 mode press Set button toset Time 2 hour and minute In Time 1 Time 2 mode press Set button to set Time 1 hour and minute and Time 2 hour and minute In addition in Medium Warm mode and Intelligent mode Set button isinactive Notes 1 Remote controller buttons except Setbutton are usedin the same way as buttons with same name oncontrol panel After adjustment is made with Set button press Confirm button to confirm 2 Remote controller has a memory function Upon re starting after powering off original settings keep unchanged 3 Asan optimum remotecontroller shall be used in shortdistance pointing tothe machine vertically Water immersion shall be avoided If battery isused up to prevent battery liquid pollution please open battery cover in indicated direction remove used batteries and replace with new batteries installed as original To avoid explosion used batteries shall not be keptin hot placesor put infire but shallbe treated inaccordance with related local regulations Electric Circuit Diagram MT L De Leakage Coil N JE ar a1 Rel
16. ing status machine automatically starts heating when actual water temperature is 5C for setting value lower than 55 C or 10 C for setting value equal to or above 55 C lower than the setting value until reaching setting temperature again It repeats in this way Example Fig 9 shows real time heat warm status with heating power 1300W and temperature setting 75 C 2150W 1300W Ee _ 7 C m Fig 8 Fig 9 6 Medium Warm Setting With machine powered on as described in Item 10 press Mode button until it enters Medium Warm operation mode with Medium Warmindication on the display 9 Dimensions Fig 1 Front View Bottom View al Pe l a OR oS E ma Cl l Drain Net Model Volume Weight a1 b1 c1 d1 FCD JTHMG50 III E 50L 22kg 671mm 442mm 100mm 410mm FCD JTHMG60 II E 60L 25kg 765mm 442mm 100mm 410mm FCD JTHMG80 IIl E 80L 29kg 876mm 479mm 100mm 450mm FCD JTHMG100 III E 100L 34kg 1052mm 479mm 100mm 450mm Remarks the permitted errorlimit of above parameters is 10 Attentions in installation During installation adequate space must be reserved for future maintenance and repair Ifthe water heateris installed withindecoration boards theright board shallbe removable to facilitate removing the plasticcover during maintenance
17. om the showerhead or other outlets the tank is full Check connections are free ofwater leakage andinsert the power plug 1 Powering On This producthas a powerfailure memory function i e it remembers temperature setting power level clock and current working status Upon connecting power allindications on the display are displayed for 2 s before the system goes into standby status with only clock display and all buttons except On Off button inactive or previous working status before power failure with corresponding indicators lighted on For example machine as shown in Fig 6 is instandby status withonly On Off button active 8
18. ore reaching delayed use time machine will calculate heating time again and determines if re heating is needed or not Likewise if water heater hasn t reached set temperature at delayed use time due to too low supply voltage machine also automatically extends forhalf an hourand stops 10 Operation Mode Selection After powering on by consecutively pressing Mode button system will shift between Real time Heat Warm with Real time indication Medium Warm with Medium Warm indication Night Power with Night Power indication Time 1 with Delay and indication Time 2 with Delay and indication Time 1 Time 2 with Delay and O indication and Intelligent with Intelligent indication modes User can select any modeas current operation mode Only after being selected as current operation mode corresponding settings canbe executed Example clock at7 00 heating powerof 2150 W temperature setting of 75 C temperature setting and actual temperature flash alternatively delayed useTime 1 being setat 10 00 If you wantto use water at 10 00 aftersettings are made you must press Mode button to adjust current mode as Time 1 mode Machine will automatically heats water to set temperature at 10 00 Otherwise e g in Night Power modeas shown inFig 13 itdoesn t execute Time 1 function You need to select Delay and symbol with Mode button and then Time 1 function canbe executed 11 Powering Off After taking shower youcan lightly
19. power before tank is fullof water 2 Adjust a suitable temperature before use for water temperature above 50 C may burn your skin 3 This product is closed water heater which can supply hot waterthrough pipe connection to several points like bathroom bathtub washbasin showerhead andkitchen 4 Heating adjustment canbe made flexibly all year round adapting to climate changes In long term out of use or maintenance you canclose city water pipe valve open mixing valve and moveup safety valve handle to drainthe tank Toavoid injury before nextuse it is suggested to first open hot water valve before switching on the water heater exhausting gas possibly retained in the pipeline In this case no smoke or fire is permitted near theopen valve carefullycheck and confirmall parts arein good condition 5 Provided hot water quantity can meetuse demand temperature setting shall be possibly low It can minimize heat dissipation high temperature corrosion and sedimentation ensuring a longerservice life 6 Regularly ask servicemen to make safety inspection remove sediment on heating elements and check consumption of anode bar Too much consumed anode bar shall be replaced 12 Operation Instructions 9 Delay Time Setting Delay function means that system automatically calculates the time needed to reach temperature setting value with a defaulted 2150 W power then determines the time to start heating and automatically heats to the set tempe
20. press On Off button to power off the machine Hints A With machine powered on you can press Set button to set On Off time for various modes and adjusttime with or V button In Real time Heat mode youcan press Set button to adjustclock hour and minute values In Delay mode you can press Set button to set delayeduse time In Medium Warm and Intelligent mode Set button isinactive B The machine has multiple safety means like current leakage protection over temperature protection sensor short circuit and open circuit protection which can realize full disconnection and display fault code Allfault protections are unrecoverable protection which needslocal after sales service C This water heaterhas power failure memory function You needn t re set heating power level heating temperature clock and operation mode Machine will directly go to previous working status after powering onagain 11 Safety Precautions O Check if power meter and wire size are consistent with water heater rated current If necessary ask experienced qualified electricians to check O The water heater shall use 230 V 50 Hz power supply from a separate socket no multi purpose socket and be reliably grounded Power plug pins shall be cleaned in time to avoid any contamination causing accidents like fire O Do not use damaged wire socketor appliances with loose plug otherwise accidents like electric shock short circuit and fire may occur
21. r any leakage re connection shall bemade Safety valve Hot Pa water 5i Al outlet t GOL Cold water inlet 2 ib ixing valve Showerhead Connect to drain hose Fig 4 Fig 5 Note Make sure the wall rackis reliably hungon the hooks before releasing yourhands Otherwise the waterheater may falland cause humaninjury or propertyloss Connection and Useof Safety Valve The safety valve should be connected to the cold water inlet pipe Please check carefully if the direction is correctafter installation The correct direction of installation is that the arrowhead on the safety valve shouldbe pointed tothe water heater Please connect the drain hose tothe safety valve Connect one end of the hose to the safety valve ventand the other end to the sewage drain The hose canbe cut shortor extended as necessary Thehose shall beinstalled as inclined downward The water may drip from the discharge pipe ofthe pressure relied device and that this pipe must be installed in a continuously downward direction and in a frost free environment Check safety valve once a month as follow move the small handle of safety valve ifthere s water flowing out safety valveis normal ifthere s no water flow please contact localafter sales service station The pressure relief device is to be operated regularly to remove lime deposits and to verify that itis not blocked Control Panel Illustr
22. rature before the preset delayed time to use hot water Two Delay Times Time 1 Time 2 means machine as needed can heat water intwo delayed usetimes This machine can be manually set two delayed water use times Setting will take PC clock time asreference Defaulted Time 1 use time is 17 00 and Time 2 use timeis 06 00 In Delay mode system default heating power 2150 W can t be adjusted Example as shownin Fig 12 set delayed use Time 1 at 10 30 With machine powered on consecutively press Mode button until it enters Time 1 operation status with delay indication and symbol lighted Press Set button to enter Time 1 hour setting status with Time 1 hour digits flashing Press A or V button to get 10 00 While hour digits are flashing you can press Set button to confirm and enter Time 1 minute setting Adjust the valueto 10 30 with A or V button Then you may press Set button to confirm current settings or wait 6 s after which machine automatically confirms and quits Time 2 time setting is similar to Time 1 i e press Mode buttonto enter Time 2 operation mode andset Time 2 time with Set button Note If large quantity hot water is used after delay mode is started and water heaters starts heating resultingin water heaterstill hasn t reached temperature setting atdelayed use time machine will automatically extend heating for half an hour and stops If actual temperature has reached setting value before delayed use time and it decreases by 5 C bef
23. rgy saving temperature between 35 C 40 C according to the difference between water temperature and ambient temperature normally this medium temperature can ensure small demand butnot shower For shower you need to quit Medium Warm mode and press Mode buttonto enter Real time Heating Keeping mode Then the water can be heated to the setting temperature ina short time When water temperature decreases to 34 C machine automatically restarts heating Heating power levelcan be manually set with Power button Example Fig 10 shows Medium Warm mode Press Power button to set power level 2150 W with corresponding indication lighted The actual temperature then is 52 C When it decreases to 34 C machine willautomatically re heats to40 C and keeps warm It cycles in this way In this mode the machine defaulted highest heating temperature 40 C can t be adjusted 2150W aw E o Z aG Cm5 eoe oo 00 Fig 10 Fig 11 7 Night Power Setting With machine powered on as described in Item 10 consecutively press Mode button until it enters Night Power operation mode with Night Power indication onthe display If you would use hot water in early morning you may adjust operation mode to Night Power mode Machine will heat warmin default period 0 00 on and 6 00 off Heating power level and highesttemperature can be manually set Inthis mode you can press Set button to calibrate clocktime
24. seese errer 12 Safety precautions 4 Attentions in operation 12 Setting environment eee eere 5 Use of remote controller 13 Parame tSr Pn Sansone pee 5 Electric Circuit Diagram Dimensions ee eii terie risterirpiiriaiis 6 Electric Circuit Diagram 13 Installation Attentions in Installation 6 PE ORCS Installation ceee enie esses 7 Cleaning and maintenance 14 FAQ 14 winsiation Packing list eters eissrserser restais 14 Correct Disposal ofthis product This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contactthe Say retailer where the product was purchased They can take this product for environmental safe recycling See to the physical product forthe appearance color or pattern Outlet water is cold If water temperature is properly adjusted Re adjust If thermostat is out of control Contact service station Heating time is too short Continue heating Outlet water flow and temperature is not steady If city water pressure is steady Check Unable to start machine If components are damaged Contact
25. service station Error display of E1 Circuit fault Contact service station Error display of E2 If tank is full of water or if components are damaged Fill water full or contact service station Error display of E3 If sensor is damaged Contact service station Packing List Expansion Expansion Remote Name Water Heater Safety Valve bolt hook User manual Battery controller Drain hose set pes pes pes copy pes pes ply Quantity 1 1 2 2 1 2 1 1 14 Use of Remote Controller 1 Dbutton Power on off the machine In off status clock time is displayed and can be adjusted by pressing Set button and or V button 2 Mode button With machined powered on you can lightly press Mode button to shift between Real time Heat Warm Medium Warm Night Power Time 1 Time 2 Time 1 Time 2 and Intelligent operation modes In Medium Warm mode default highest temperature is 40 C and can t be adjusted In Time 1 and Time 2 modes default heating power is 2150W and can t beadjusted 3 Ppwer button With machine powered on press this button to shift heating power level between 850 W 1300 Wand 2150 W 4 orV button Same as Adjust button on control panel If not in clock or delay time adjusting status you can use or V button to increase or decrease temperature setting value between 35 C 75 C with an increment1 C If inclock or delaytime adjustin
Download Pdf Manuals
Related Search