Graflex 4 x 5 Anniversary Speed Graphic Parts list
Contents
1. 3 Panel door spring also panel door a To replace either of the panel door springs 845 it will be necessary to remove the door from the focusing frame Proceed by removing the retaining strip 547 from each Side of the ground glass then lift the leather covering at the hinge and remove four fl x 1 4 flat head hinge screws 150Bl 4 b Drive out the hinge pin to remove broken spring Position the new spring so that the straight ends extend inward without tension Grasp one straight end and pull 1 3 1 4 to place tension on the spring If the tension is sufficient to lift the door form off wr each terminal so that it will lay flat against the hinge then cut off excess of 3 16 Ce neassemble the door check side binding and the catch and if necessary adjust the Catch arch before reassembling the ground glass LL TO PUT TENSION ON SPRING BENO OFFSET ANO CUT OFF EXCESS Cont on page 4D VERSARY SPEED GRAPHIC Section 3 x 5 ANNI 5 2672 104 B6 40 22192 o 22196 SEE NOTE N 0 22194 met 2 3 191 B1 6 8 Crer SVAN TA uns M 20608 Sw 7 22575 15851 S MA TR SA 7 150 B0 4 E i 4 X 5 ANNIVERSARY SPEED GRAPHIC Cat No 9112 GRAPHIC BACK COMPLETE Obsolete replaced by Graflok Back Cat No 9299 Includes 16026 and 30039 Order the following parts for replacement only 16026 FOCUSING FRAME ASSEMBLED includes the fourteen parts listed below 150 B02. 31914 P3 Back 3 40 Order by part number and comolete name State quantity 193 395 Prices are subject to change without notice See Price List 15 30 3D Section 3 4 X 5 ANNIVERSARY SPEED GRAPHIC 4 4D Panel wing shields a To replace a panel wing shield 2672 remove the corresponding retaining strip and pry up the metal lip of the door slightly b Clean the metal opening apply cement 3 16 wide to both sides of one straight edge of the shield insert this cemented edge in the lip and peen the lip which clamps the new shield c Replace the retaining strip Peepsight nemove the peepsight screw 104B6 4 and clean the cap 22192 peepsight 22196 tw balls 22194 two springs 22193 and the back bushing with cleaning solvent Stretch the springs slightly lubricate the bearing faces of the peepsight with a wax base lubri cant and reassemble NOTE Cap 722192 should be ordered to accommodate the peepsight bushing surface of the back The cap has been made with and without the bearing shoulder The cap and back of figure a is currently supplied the cap of figure b will be supplied only on request 39 24 Back lugs and screws If the threads of the back lugs positioned in the camera body beneath the leather should be stripped by over turning or cross threading the back screw 110B2 3 it will be necessary to retap the lug with a 3 48 tap and use a 73 48 x 3 16 binding head screw uraflok
3. 20 25062 Gl Curtain Assembly 5 50 20600 Spacer Washer curtain roller Ol 24669 Bearing roller 35 35 section 3 4 x 5 ANNIVERSARY SPEED GRAPHIC Ak Reassemole the back with the focusing panel removed set the curtain slit at A and set the tension at 1 Release the curtain and note if it rebounds at the lower edge of the opening this fault may be corrected by dropping the upper roller gear one tooth off the plate gear Tension setting plate 724664 ae The tension dog spring 15 may De replaced without removal of the plate De If the entire plate is to be removed use the special tension lock nut wrench and pliers to remove the tension snail lock nut 24496 The tension snail 26354 may now be unscrewed from the tension roller shaft it may be necessary to wind the tension to 6 before the tension snail can be unscrewed at this point the four fl x 1 4 oval head screws 152Bl 4 are removed and the plate lifted from the camera body 38 22 Ce Lubricate the case and plate bearing points of the tension roller shaft with graphite grease and lubricate the internal tension spring with a few drops of light oil inserted through the left end see below paragraph 3C d neassemble the tension setting plate over the threaded end of the shaft and lock the tension setting clamp to the shaft Check side play of the roller and if more than 1 64 use spacer washer 30600 at the case bearing end of the shaft Wind t
4. 3 Screw retaining strip 3 16 0 FH L95 150 BO 4 Screw Catch to frame 1 4 0 FH P22 150 Bl 4 Screw panel to frame 1 4 1 FH Ll7 151 Bl 6 Screw spring to frame 3 8 1 RH L5 547 Strip shield retaining 343 Catch panel catch 2670 Screen ground glass 2684 Frame wood not leather covered 2693 Panel door assembled not leather covered 845 Spring panel door 2672 Shield panel wing 16016 Covering frame and panel assembly 22574 Spring assembly bottom of focusing panel 22975 Spring assembly top of focusing panel 30039 BACK FRAME ASSEMBLY Cat No 9107 SWINGING PEEPSIGHT includes first five items below 104 B6 4 Screw peepsight 1 4 46 32 OH P16 22192 Cap peepsight specify type see page 4 22193 Spring peepsight 22194 Ball peepsight 22196 Peepsight 21993 Back frame 110 B2 3 Screw back to body 3 16 42 56 Bind H L 12 15851 Washer spring screw 20608 Screw panel spring to back 1 4 44 40 RH P22 Cate No 9299 GRAFLOK BACK COMPLETE 4 x 5 with Ektalite Refer to Section 6 to order parts except for the following items Section 3 List Price See below 9 60 1 00 2 70 1 90 OL Pacemaker Part as listed Order this Anniversary Part 30921 P6 figure 8 2 110 B2 3 Screw Upper Mounting 3 16 42 56 Bind H 01 30921 P7 figure 8 1 110 B2 3 screw Lower Mounting 3 16 2 56 Bind E Ol 31710 G3 31710 G5 Back Assembly less panel amp hood 31914 P1 figure 3 28
5. front bellows frame to the lensboard frame Replacement d With the seam down assemble the screws which secure the front bellows frame to the lensboard frame Tack the sides of the bellows first to the inside frame then support the wood frame by inserting something of suitable thickness and strength over the curtain roller to act as a levered support while tacking the top and bottom edges Plug any holes with a mixture of lampblack whiting and glue or some other suitable material e Heplace the idler frame securely against the inside frame straighten the curtain and reassemble the back Folding Peepsight 25036 This peepsight is used with the front wirefinder 25026 which has a slide bushing 2 1 4 long To remove excess play from the peepsight remove the hinge pin reform each of the right angle tabs to form 90 degrees and from the center section of the base plate upward about 1 32 inch above the outside section Reassemble Idler Lubrication Remove the idlers and frame clean in solvent dry and lubricate the bearings with graphite grease Bed Catch 22528 If the bed catch 22528 should fail to open the bed when the top release button is de pressed the bed can possibly be eased open by inserting a piece of very stiff L shaped wire Insert the hook through the crack and twist the wire hook down against the catch while depressing the button in many cases this will open the bed If the catch plung er
6. with inserts Order pin 4918 Strip Lensboard retainer Ball Standard lock Includes seven items below Nut Front standard screw Spring Shift lock Washer Front standard spring Washer Front standard flat Lever lock assembly Standard assembly 26355 P2 Nut Rising Front Lock order replacement substitute Replacement Parts Parts as listed 25044 26355 P2 193 355 25026 WIRE FINDER Use with folding peepsight 25036 25095 WIRE FINDER Use with swinging peepsight 22196 25044 HANDLE ASSEMBLY Non adjustable order replacement PARIS FOR ATTACHING HANDLE ASSEMBLY 100 3 8 Screw Handle due 1 2 43 43 FH P19 102 3 8 Screw Handle catch 1 2 43 48 RH P19 24672 Catch Handle 24674 Spring Handle catch 25096 Plate Handle reinforcement tapped for 3 48 thread 104B6R3 Screw Handle bracket Use with 33779 Gl only 30374 Pl Bracket Handle Use with 33779 Gl only 30375 P1 Nut Handle bracket Use with 33779 Gl only Order as Replacement 33779 G1 Handle assembly 30444 P1 Nut Order by part number and complete name Prices are subject to change without notice Rising front lock order for replacement See paragraph 5 section 3 List Price 16 00 3 50 40 04 OL 1 90 3 60 See below 4 20 4 20 See below only 03 1 85 25 State guantity 3C n TOC CIO AM porta Sastisn 3 4 x 5 ANNIVERSARY SPEED GRAFHIC Tu e
7. 4X 5 ANNIVERSARY SPEED GRAPHIC eU mab ystig 7 3 5 d j i a Y i E i Mb H 2 f i i f dmn tn wr mm ies men front tjv sontes treo nimmer mM EC AB tau mess Bellows 2 1 2 in min to 13 in max Lensboard 4 in square Model C Cat No 2903 Lens limit 3 1 4 in max dia of rear element 1 7 16 in forward from lensboard to closed bed GRAFLEX INC Rochester 8 New York Section 3 CONTENTS OF SECTION 3 DESCRIPTION Miscellaneous Parts Bellows Folding Peepsight Parts List Bed Assembly Replacements and Adjustments Parts List Bed Inspection Tripod Socket Replacement Front Standard Open Finder Handle Parts List Graphic Back Focusing Frame Parts List Graflok Back Focal Plane Shutter Curtain Setting Plate Parts List Tension Setting Plate Curtain and Roller Assembly Optical Viewfinder Refer to Section 102 4 x 5 ANNIVERSARY SPEED GRAPHIC Section 3 Miscellaneous Parts Special precautions for i 1 Bellows e Peepsight folding 3 Idler lubrication 4 Bed catch Bellows 16034 Removal a Remove the back set the curtain at O remove the side screws of the idler frame and the idlers b To free the rear of the bellows from the camera body pry out the 20 small nails 6459 and remove the bellows and front standard from the front of the camera c Working inside the bellows remove 8 screws 29796 which secure the
8. E ap gsi lt 24663 4 x 5 ANNIVERSARY SPEED GRAPHIC section 3 List Price 24664 TENSION SETTING PLATE ASSEMBLY 2 40 15 Spring tension dog 08 104 Screw tension indicator gear I5 24496 Nut tension snail lock 20 24660 Plate tension order tension setting plate assembly 24664 24661 Gear tension indicator 450 24662 Screw tension dog 08 24663 Dog tension 30 26354 Snail tension plate setting 40 152 Bl 4 Screw plate to body 1 4 1 OH L5 03 24780 CURTAIN SETTING PLATE ASSEMBLY 9 80 355 Bushing shutter release order 2013 and 24665 ss 866 Washer release 05 867 Screw escapement 05 868 Spring escapement 15 2013 Nut escapement lever order 855 and 246675 12 3388 Escapement assembly 40 3397 Gear master 1 75 22010 Button shutter lock JO 22011 Stud Screw latch lock 05 22012 Latch shutter lock order 22010 10 22013 Washer escapement spring wasner 03 22014 Washer lock 03 22015 Lever escapement order 855 2013 and 24665 10 24324 Gear curtain slit indicator 50 24665 Screw release lever order 355 and 2013 O5 24666 Lever shutter release order 355 2013 and 24665 25 24682 Winding key 50 24779 Plate setting order curtain setting plate assembly 24780 29933 Pin winding key 01 152 Bl 4 Screw plate to body 1 4 1 OH L5 03 CURTAIN AND ROLLER ASSEMBLY 10 00 2697 Roller assembly gear 1475 2698 Roller assembly tension 2
9. back a Refer to Section 6 for disassembly and reassembly of the Graflok back b Description of mounting screws shown in figure 4 1 and 4 2 in Section 6 are not ac curate descriptions of screws used on the Anniversary Graflok back See Parts List of this section 4 x 5 ANNIVERSARY SPEED GRAPHIC Section 3 Focal Plane Shutter Special precautions for 1 Curtain setting plate 2 Tension setting plate 3 Curtain and roller replacement Special tools Tension setting clamp 28452 Tension lock nut wrench 28442 All metal parts of the shutter plates may be immersed in cleaning solvent dry before reas sembly and lubricating as recommended below Remove excess lubricant and never allow any lubrication to come in contact with shutter curtain l Curtain setting plate 24780 a Remove the back NOTE Set the curtain at O full open aperture and mark the position of the top curtain strut on one side of the camera body b From the curtain setting plate remove the five 1 x 1 4 oval head screws 152B1 4 Note any spacer washers 20600 that may be placed at either end of the roller Ce If it is ever necessary to remove the release lever 22015 file off the peened end of the release lever screw 24665 Reassemble peen nut and check for binding of bush ing or too tight screw de Check brake spring of the escapement 3383 in respect to its latch of the master gear stop pin Hold the shutter release
10. er 05 24246 Screw Yoke tension 3 16 3 48 Headless P22 03 24247 Guide Right bed yoke 20 24248 Block Right bed 65 24249 Block Left bed 65 24250 Pad Yoke tension 03 24251 Focusing pinion assembly Order 2 knobs 26356 2 35 25016 Guide Right Obsolete order only as replacement 60 25017 Guide Left 60 25018 Bed and hinge 5 75 25037 Spring Bed brace plunger 05 25038 Pinion Obsolete order only as replacement with 2 knobs 26556 2 95 29043 Yoke assembly 12 00 25046 Screw Bed block 03 25051 Covering not illustrated 1 20 25063 Washer Yoke lock spacer as required order replacement 03 26356 Knob Focusing se 22518 Stop Left infinity 80 22524 Stop hight infinity 80 100B4 3 Screw Yoke guide to case 1 2 4 40 FH L5 05 150B2 5 Screw Bed hinge 5 16 2 FH L12 03 24483 Screw Focus scale 05 25050 Washer Yoke guide screw e 03 152B2 4 Screw Side arm plate l 4 2 OH Ll7 01 25004 Plate Right side for bed arm brace 32 25005 Plate Left side for bed arm brace 35 Substitute Replacement Parts Parts as listed Order as replacement 25063 30473 Pll Washer Yoke lock as required 01 3B Section 3 4 x 5 ANbIVsnsaRY SPEED GRAPHIC De 4B Lock Replacement and adjustment See paragraph 2c Focusing Scale For information pertaining to focusing scales refer to Section 101 Bed Inspection Check List ae Note focusing pinion action for Check s
11. ft 60 25067 Moulding lower right 60 25068 Moulding lower left 60 29796 Screw bellows to front standard 2 FH Parker Kalon 01 30084 Pin tack shutter speed plate to body Ol Substitute Replacement Parts Parts as listed Order as replacements 22184 30640 P2 Nameplate LO Order by part number and complete name State quantity Prices are subject to change without notice 193 355 JA 4 x 9 ANNIVERSARY SPEED GRAPHIC section 3 Bed Assembly Special precautions for l e 1 Focusing pinion tension 2 Bed block and guide replacement and adjustment Focusing pinion replacement Yoke replacement Lock replacement and adjustment 3 4 2 6 Focusing scale 7 Bed inspection check list 8 Bottom tripod socket repair Focusing Pinion Tension If the tension adjustment screw 24246 located on the right side of the pinion is tightened the tension on the pinion should increase however if the tension does not increase the tension pads 24250 will need to be added The tension should be just enough to hold the yoke when the camera is tilted forward without the yoke lock lever be ing set This does not apply to beds with lock screw part 22131 Bed Block and Guide Replacement and Adjustment Disassembly a Remove the front standard from the yoke and if necessary remove the focusing scale and the side bed brace plates 25004 and 25005 Remove the yoke guide screws the yoke guide and the
12. he spring several turns and then draw the curtain out by hand Several times to remove curtain slack Slow ly release the tension do not allow the tension setting clamp to spin free Lift the tension plate set the indicator gear so that I appears in the indicator hole turn the one tooth of the pinion clockwise from the vertical about 30 degrees and now engage the counter gear and the one tooth pinion If it is not possible to wind the tension to 2 the pinion and gear are not properly engaged repeat and vary the 30 degree suggestion slightly e With the tension setting clamp wind the tension to hold the tension lift tne plate and reset the counter to 1 Check for correct mesh of pinion and indicator gear then assemble two screws iemove the tension setting clamp and rethread the tension snail to the shaft Screw tbe snail down until it binds on the plate then back of a partial turn until the dog and snail catches engage Insert spacer 005 to 010 between the catches assemble the tension nut and tighten Check the snail for binding on the plate if necessary loosen the locknut and back off snail a full turn tighten lock nut again and check Test run several times at high and low tension then set tension at I and the curtain at O invert the camera and release the shutter the curtain should roll slowly and evenly to the roller and latch with release lever held back if not it will De necessary to add more tensio
13. ing of the side brace plate Slide standard from case to bed and note any unevenness at the hinge if the bed is low shim beneath bed block with thin fiberboard or if the bed is high draw down by tightening bed block and guide screws Check focusing scale and rangefinder ees adjust rangefinder infinity with the case yoke eccentric screw Focusing Pinion Replacement See paragraph 2 above for disassembly reassembly and adjustment of bed Lubricate the focusing pinion shaft bearing surfaces with wax base lubricant Yoke Heplacement See paragraphs 2b c and d for assembly and adjustment Cont on page 43 13 Section 3 NS kw e ner 4 AT lee br Dl em 2B 29017 4 x 5 ANNIVERSARY SPEED GRAPHIC gt 7 29016 22131 d 24246 M ama sv on 3 uu a ada Sect E 3 Ss E i n dos sina E 4 X 5 ANNIVERSARY SPEED GRAPHIC Section 3 List Price 33 50 100 B2 4 Screw Yoke guide 1 4 42 56 FH L5 For use with 24247 25017 ONLY Ol 28344 BED ASSEMBLED COMPLETE Includes the twenty two current items below 20041 Spring Focus pinion shaft 03 22117 Plunger Sed brace spring 10 22130 Lever Yoke lock e9 22131 Screw Lock Obsolete order as replacement only A 22132 Stop Right yoke 05 22133 Stop Left yoke 05 22172 Bushing Yoke guide screw 01 24244 Sleeve Yoke lock lev
14. late 25096 which is positioned inside the case Substitute replacement parts a Handle assembly 1 Handle assembly 25044 is replaced by handle 33779 Gl and requires the use of two new handle brackets 30374 Pl two handle bracket nuts 30375 Pl and two screws 104B6R8 2 To position the handle brackets place the template Fig 1 on the left side of the camera align the top bottom and front of the template with the camera and drill six 0 144 holes as indicated Position handle bracket nuts from inside of camera case and clip off the ends protruding from outside of camera box until approximately 1 32 of the end protrudes Mount handle bracket and secure with screw 3 The nandle is assembled as shown in Fig 2 Cont on page 4C 10 section 3 4 x 5 ANNIVERSARY SPEED GRAPHIC a 29026 Or 25095 SEE NOTE PAGE 4 KAT SD UT f 24815 SPEED GRAPHIC I NW YN P o aaa 20605 i atom papa ittm L 24674 AT a Mel Wer A VICAR LE 20 25012 25023 4918 20605 24471 24915 25022 25048 25047 22104 22108 22176 22185 22186 22501 25021 FRONT COMPLETE STANDARD COMPLETE 4 X 5 ANNIVERSARY SPEED GRAPHIC Slide Lock Lensboard Screw retaining strip 3 16 2 OH Parker Kalon Includes 25023 25047 and 26355 P2 LENSBOARD FRAME COMPLETE Includes six items below Pin Slide lock centering Screw lensboard slide lock Frame
15. lever back and rotate the winding key until the Stop pin snaps beneath the flat spring and against the escapement it should not be pos Sible to reverse the winding key and force the stop pin back under the catch end of the flat spring This spring should latch about 1 64 below the top of the pin If it has been necessary to remove the escapement screws 867 apply a touch of glyptol cement to the threads before assembly e Lubricate the mastergear stop pins with wax base lubricant and lubricate the curtain roller bearings and pinion with graphite grease f Set the curtain setting plate so that O appears squarely in the indicating hole when the top gear stop pin is stopped against the escapement ge Wind the curtain so that its top strut lines up with the index mark on the side of the body Hold the winding key against the stop and reposition the plate check the side play of the roller and if more than 1 64 use spacer washer 20600 at the case bearing end of the shaft Reassemble two screws test run check the top strut and index if sat isfactory wind the curtain and release note the position of each curtain strut in re lation to the inside frame If necessary adjust by raising or lowering the pinion gear one tooth at a time La 1 Cont on page 4E lE 4 x 5 ANNIVERSARY SPEED GRAPHIC section 3 f o M EEA AN EA NDA 20600 94665 i L a 152 B1 4 LAO H
16. n one turn at a time until the shutter operates inverted Tnis additional tension may oe added by removing the plate mounting serews and rotating the plate counter clockwise without disengaging the pinion and indicator gear Check operation as instructed in paragraph 1 g Reassemble the four screws when tension is sat isfacto ry 3 4 x 5 ANNIVERSARY SPEED GRAPHIC Section 3 Curtain and roller replacement ae lf the curtain and rollers are not being replaced as amit remove all old cement from the rollers and rough the curtain and be sure that the ends of the curtain are Square which will facilitate in keeping the curtain ends as nearly parallel as possible to the longitudinal axis of the rollers when the parts are cemented together ixamine the curtain for pinholes tears or weak points b For information of assembly and lubrication of the curtain and tension setting plates see corresponding paragraphs l and 2 abovee c Examine the tension roller spring by unscrewing the left bushing then unscrew the right bushing Lubricate spring very lightly with recommended light oil or replace tension roller if the spring is badly worn de After the new curtain or roller has been replaced and adjusted it is additionally cemented to the roller The top gear roller is set at 0 and released a line is drawn across the center of the roller which will mark a guide on the inside surface of the curtain Cement is applied 1 2 wide on this guide li
17. n 8 me NK rua 144 inch dia drill 6 holes Neo o heces dec 2 Figure 1 Template Handle mounting Figure 2 Handle Assembly 4 X 5 ANNIVERSARY SPEED GRAPHIC Section 3 GRAPHIC BACK Special precautions for 1 Foeusing panel springs 2 Ground glass replacement also panel catch 3 Panel door spring also panel door 4 Panel door shields 5 Peepsight 6 Back lugs and screws 7 Graflok back l Focusing panel springs NOTE The bottom and top focusing panel springs 22574 and 22575 are not interchange able to determine position the ear with the elongated slot on the right and lastly the straight edge will be to the center Ihe springs are secured to the focusing panel at each end by a 1 x 3 8 round head screw f 15181 6 in turn the panel and springs are secured to the back by a 4 40 x 1 4 round head screw 20608 inserted through the center hole of the spring through a washer part 15351 and into the back moulding bushing 2 Ground glass replacement also panel catch a Cpen the panel door and on each side remove the metal side shield retaining strip 547 which is secured by four FO x 3 8 flat head screws 150B0 3 b At this point check catch panel wing shield and door spring for replacement c Position the ground glass screen 2670 with the grain surface toward the lens Clineh the panel wings beneath the retaining strips and tighten the screws uniformly to avoid cracking the glass
18. ne The lower tension roller is marked with a guide line after the smallest aperture has been wound on the top roller cement is applied 1 2 wide on this guide line Reassemble the back and check TENSION LOCK NUT WREN CH TENSION NUT 24496 SNAIL 26334 006 24663 INSERT APPROXIMATE 010 SPACER BEFORE TISMTENING TENSION NUT Che f 55
19. sticks or is rusted replace the catch and or lubricate the spring and plunger with light oil wipe away excess oil At this time adjust the hooking portion of the catch to eliminate future jamming lA Section 3 4 x 5 ANNIVERSARY SPEED GRAPHIC NIS AP DN i E i e b 25036 152 B1 3 One ea 4 x 5 ANNIVERSARY SPEED GRAPHIC Section 3 Miscellaneous Camera Body Parts List Price 150 Bl 4 Screw bed stop to body 1 4 1 FH Ll7 Ol 150 B2 4 Screw side tripod bushing to body 1 4 2 FH Ll2 03 150 B3 6 Screw idler block to body 3 3 2 FH 818 03 151 BO 3 Screw roller shield to body 3 16 0 RH L5 03 151 B2 4 Screw bed catch to body 1 4 2 RH Ll7 03 152 Bl 3 Screw folding peepsight to body 3 16 1 OH P19 03 2071 Tripod bushing side use screw 150 B2 4 1 6459 Nail bellows to rear frame O1 15696 Foot camera 03 16001 Shield bottom tension roller 40 16034 Bellows use rear frame nail 6459 and front frame screw 29796 6 95 16044 Shield top gear roller 40 17471 Idler curtain es 21999 Idler block assembly use screw 150 B3 6 20 22184 GRAFLEX name plate front moulding See Substitute Parts List 22528 Bed catch assembly use screw 151 B2 4 25 25036 Peepsightfinder folding use with wire finder 25026 1 15 25054 Stop bed use screw 150 Bl 4 15 25060 Plate shutter speed use pin 30084 elo 25065 Moulding top right 60 25066 Moulding top le
20. th a wax base lubricant Lock lever and lateral shift lock spring replacement and adjustment The lateral shift lock sprins 22176 is secured to the bottom of the standard by a 23108 Note the screwslot do not move unless the lock tension is to be changed The lock lever 22501 is secured by the hexnut on the bottom and threaded through the standard When reassembling lay the two lock balls 22104 in their sockets first assemble the spring washer 22185 over the lock lever screw then assemble the flat washer 422186 over the screw and thread through the standard Replace the shift spring locknut test the locking action on the bed To tighten the lock loosen the loeknut on the bottom side and turn the screw in a counterclockwise direction to loosen the lock turn the screw in a clockwise direction and then tighten the locknut Wirefinder The wirefinder and peepsight combination must be used as the table below indicates Peepsight Wirefinder Folding sight 25036 25026 bushing 2 1 4 long Swing sight 22196 425095 bushing 2 l 2 long Lubricate the sliding parts by wiping with a wax base lubricant Handle Early models of this camera use wood screws to secure the handle plates To use the re taining plates 25096 and machine screws 100 3 8 and 102 3 8 that are listed drill through the center of the wood screw hole with a 099 diameter 39 drill and assemble the machine screws into the retaining p
21. traightness clean and bind or grate lubricate b Note side play and alignment as See paragraph ed the case yoke engages the bed section Co Lock lever See paragraph ec de Focusing pinion tension see paragraph l Bottom Tripod Socket Repair a If the bottom tripod socket has broken free remove the bed from the camera body It will be necessary to remove the side arm brace plates three 2 x 5 16 flat head screws part 150 B2 5 from the inside and four 4 40 x 1 2 flat head screws part 100 B4 4 from the bottom De Level the broken hinge emboss file or peen smooth c Position a side tripod nut 2071 see Section 3A page 3 Cut a plate about 4 diameter and drill three 1 8 holes to correspond to the three holes in the nut 3 flange Lay the plate over the nut and assemble to the camera body with three 2 x 1 4 round head screws 151B2 4 de HReassemble the bed and check with paragraph 7 4 X 5 ANNIVERSARY SPEED GRAPHIC Section 3 Front Complete and Handle Special precaution 2 Je 1 4 28 x 3 8 hexnut 4 l Lensboard frame and slide locks 2 Lock lever and lateral shift lock spring replacement and adjustment 3 Wirefinder 4 Handle 5 Substitute replacement parts Lensboard frame and slide locks Ihe lensboard frame 25022 is secured to the bellows from the inside by eight 2 flat head Parker Kalon screws 29796 The slide lock 20605 should be lubricated by wiping the back wi
22. yoke the bed block may now be removed press the side brace ear outward slightly for clearance if necessary Clean yoke guides and yoke in solvent dry and lubricate with wax base lubricant Reassembly b Ilf the bed blocks have been removed position the focusing pinion with the yoke lock post to the right of the bed position the shaft spring 20041 and the bed brace plunger spring 25037 and plunger 22117 beneath each of the blocks and against the outside edge Reassemble the bed block screws and tighten Reassemble the yoke guides with the yoke replace the screws press both of the guides to the center with egually steady pressure and tighten the guide screws Ce Agjust the yoke lock lever by sliding the yoke case section back out of the guides after the bed has been dropped If the post type lock see focus pinion part 24251 is used assemble sleeve 24244 tensions pads 24250 and the tension screw 24246 For either the post type or the square head screw type 22131 as semble the lock lever 22130 the lever should not lock when forward but must lock when turned about 60 degrees to the right restart double lead thread or use Spacer washer 425063 to obtain satisfactory locking action Adjustment d If the side brace plate has been removed check the bottom of the bed and case with a straight edge Check guide surface of the yoke by laying a straight edge on top surface of each side adjust by slight reposition
Download Pdf Manuals
Related Search