Graco 3A0416C User's Manual
Contents
1. bb Tee Fitting CC Stop Valve dd Lube Point ee Lubricator ff ON OFF Switch 7 Ensure the stop valve cc of the pressure manometer is open 8 Attach lubricator and adapter B to the pressure manometer aa cc and turn the switch to ON ff FIG 1 9 Run the manometer for about 20 seconds Observe the gauge and repeat this proce dure until the pressure registered on the gauge stays constant 10 To determine the counter pressure wait approximately 5 minutes until the system has relaxed Do one more discharge by turning the unit OFF then ON again until it dispenses for no more than 5 seconds 11 Wait approximately 5 more minutes to make sure the system does not lose pres sure and remains constant 3A0416C Installation and Setup 12 To disconnect lubricator from manometer follow pressure relief procedure page 6 NOTE In this application you will be dis connecting adapter B from manometer instead of lubrication point NOTICE Do NOT disconnect lubricator from adapter B Screwing anything into lubricator a sec ond time will damage self sealing threads 13 If the counter pressure is 5 bar 72 5 psi or higher flush the lubrication point with a grease gun If the counter pressure does not decrease you may need a different lubricant or size lubricator canister Contact Graco Cus tomer service for assistance Priming Pre filling Fittings and Grease Lines A2. 124110 124111 124112 Description CAP top CAP full 60 120 cc CAP full 250 cc Qty 400 Gram Lubricant Cartridges Part No 124176 124177 124178 124179 124180 124181 124182 124183 Description CARTRIDGE lubricant Lith ium EP 2 CARTRIDGE lubricant Con struction CARTRIDGE lubricant Bear in C RTRIDGE lubricant Milling CARTRIDGE lubricant Food Grade H1 CARTRIDGE lubricant Syn thetic Industrial CARTRIDGE lubricant Ultra Spindle CARTRIDGE lubricant Lith ium EP 1 Qty 1 1 4 3A0416C Refill Kits Part No 24E582 24E583 24E584 24E585 24E586 24E587 24E588 24E589 24E590 24E591 24E592 24E593 Description KIT refill 60 cc multi EP 2 KIT refill 60 cc construction KIT refill 60 cc bearing KIT refill 60 cc mill KIT refill 60 cc food KIT refill 60 cc synthetic KIT refill 60 cc ultra KIT refill 60 cc multi EP 1 KIT refill 120 cc multi EP 2 KIT refill 120 cc construction KIT refill 120 cc bearing KIT refill 120 cc mill Technical Data Cable Construction Conductor cross section dimensions Power Supply Total current consumption Maximum output load Temperature range Maximum output pressure Storage Conditions Temperature Air born Noise Emission Qty LL IL L IL I Il ll ll Technical Data Part No 24E594 24E595 24E596 24E597 24E598 24E599 24E600 24E601 24E602
3. 24E603 24E604 24E605 Description KIT refill 120 cc food KIT refill 120 cc synthetic KIT refill 120 cc ultra KIT refill 120 cc multi EP 1 KIT refill 250 cc multi EP 2 KIT refill 250 cc construction KIT refill 250 cc bearing KIT refill 250 cc mill KIT refill 250 cc food KIT refill 250 cc synthetic KIT refill 250 cc ultra KIT refill 250 cc multi EP 1 Cable is drag chain qualified approved for the smallest bending radius 60 mm 4 x 0 25 mm 15 25 VDC max 30 VDC 5 residual ripple for the duration of the actual lubricant dis charge 0 2 A current at discharge can be up to 1 2 A Pin 2 and 4 cannot exceed 400mA each 10 C to 50 C 14 F to 122 F 5 bar 75 psi Dry dust free 20 C 5 C 68 F 9 F 70 dB A T Loctite is a registered trademark of the Loctite Corporation f Emission sound pressure level of the lubrication system measured at distance of 1 m height 1 6 m 3A0416C 23 Qty L IL JL ee L Ll ll lh Technical Data Weights and Measurements Diameter D Length L Weight empty Bre s ane vi vs wr su ono ver 1 4 npt Lubrication Canister 24 3A0416C Notes 3A0416C Notes 25 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the o
4. breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s la suite de ou en rapport directement ou indirectement avec les proc dures concern es Graco Information For the latest information about Graco products visit www graco com TO PLACE AN ORDER contact your Graco distributor or call to identify the nearest distributor Phone 612 623 6928 or Toll Free 1 800 533 9655 Fax 612 378 3590 All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Original instructions This manual contains English MM 3A0416 Patent information www graco com Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 Copyright 2010 Graco Inc is registered to ISO 9001 WWW graco com December 2014
5. 3A0416C Installation and Setup Grease Lubrication with Tube FIG 5 A Clip 124086 B Support adapter 124105 C Bracket 124087 D Tube connector User supplied E Nylon tube User supplied F Tube connections User supplied Must be at least 5 16 inch diameter tube 15 Installation and Setup From top lubrication of a Chain with Oil Clip 124086 Support adapter 124105 Bracket 124087 Tube connector User supplied Nylon tube User supplied Tube connections User supplied Oil throttle 124102 L Bracket 124098 Bulkhead mounting plate 124099 Oil brush 1 x 1 5 124090 The non return valve oil throttle G should always be placed at the lowest point of the application Must be at least 5 16 inch diameter tube AS T Q TI II O O gt FIG 6 16 3A0416C Lubrication of Elevated Chain with Oil sl 9 FiG 7 Clip 124086 Support adapter 124105 Bracket 124087 Tube connector User supplied Nylon tube User supplied Tube connections User supplied Oil throttle 124102 The non return valve oil throttle G should always be placed at the low
6. AND EXPLOSION HAZARD When flammable fluids are present in the work area such as gasoline and windshield wiper fluid be aware that flammable fumes can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Eliminate all ignition sources such as cigarettes and portable electric lamps Keep work area free of debris including rags and spilled or open containers of sol vent and gasoline Do not plug or unplug power cords or turn lights on or off when flammable fumes are present Ground all equipment in the work area Use only grounded hoses If there is static sparking or you feel a shock stop operation immediately Do not use equipment until you identify and correct the problem Keep a working fire extinguisher in the work area TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin inhaled or swallowed e Head MSDSs to know the specific hazards of the fluids you are using e Store hazardous fluid in approved containers and dispose of it according to applica ble guidelines 2 3A0416C 3A0416C PRESSURIZED EQUIPMENT HAZARD Fluid from the equipment leaks or ruptured components can splash in the eyes or on skin and cause serious injury Follow the Pressure Relief Procedure before cleaning checking or servicing equipment e Tighten all fluid connections before operating the equipment Check hoses
7. G31p l T7 Z lt i X92e q SIGeD 3A0416C Component Identification PLC Connection Three Output Signals r 1 sjndino Jeuruu9 21d i yeoaiq 9 qeo Aydwa yun 51 uoljounjjew uauM uBiH ZO zo yndjno L w a a a a w L Avo Bunyi 9sS 3 0 19S Lg e 0 pon sjndu Jeuruia Old jeuBis uogounjjeui y Buoys Jo Auessaoau Ajuo yeuondo LL8 608 L08 aqq uee6 bl 2es0G PUE os 9JuM lqeO jeuBis uaeJ6 ou y82Jq qe5 S08 jeuBis pos ou AUI dt 908 98S OZL qa1 pei el lt yoelq lqe2 Klians J9wMod L G al 3A0416C Installation and Setup Installation and Setup Determining Correct Mounting Method NOTE Direct mounting should be used for lubrica tion points that are easily accessible Remote mounting is recommended if you answer YES to any of the questions below Is the ambient temperature at the lubrica tion point higher than 50 C 122 F Is it necessary to remove protective screens walls or other types of protection in order to reach the lubrication point Is the lubrication point exposed to high vibrations Is it difficult to access the lubrication point during operation of the machine Is the lubrication point exposed to any of the following e water jets for high pressure cleanin
8. the lubrica B LED Green tion canister it will lead to a wrong C 4 way code switch signal and over or under lubrication D Plug connection E Circuit board 12 3A0416C Installation and Setup TABLE 1 Dip Switch Settings Discharge Amounts in CC Impulse e Amount of discharge in cc per impulse e White square indicates position of dip switch ubrication Canister Size Dip Switch Position NOTE e As soon as power is supplied the controller will discharge the set amount once Power must be applied at least until the discharge has taken place approximately 2 minutes e norder to get another discharge cycle the power must be interrupted for at least 15 sec onds and then supplied again 3A0416C 13 Installation and Setup Selecting Mounting Location Installation Guidelines An e e Before installing the lubricator the lubrica tion points and any extensions must be adequately pre lubricated with the same lubricant contained in the lubricator A 400 gram lubricant cartridge for grease guns is available from Graco See Parts page 22 for a complete list of available lubricant car tridges e Install one lubricator per lubrication point e When oil is used for lubrication a non return valve oil throttle must be installed This will prevent oil leakage from the lubricator An oil throttle part number 124102 is available from Graco See Parts page 22 e An oil fill
9. tubes and couplings daily Replace worn or damaged parts immediately EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury Do not operate the unit when fatigued or under the influence of drugs or alcohol Do not exceed the maximum working pressure or temperature rating of the lowest rated system component See Technical Data in all equipment manuals Use fluids and solvents that are compatible with equipment wetted parts See Technical Data in all equipment manuals Read fluid and solvent manufacturer s warnings For complete information about your material request MSDS from distributor or retailer Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use Check equipment daily Repair or replace worn or damaged parts immediately with genuine manufacturer s replacement parts only Do not alter or modify equipment Do not puncture open or take lubricator apart Use equipment only for its intended purpose Call your distributor for information Route hoses and cables away from traffic areas sharp edges moving parts and hot surfaces Do not kink or over bend hoses or use hoses to pull equipment Keep children and animals away from work area Comply with all applicable safety regulations Models PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating servicing or when in the operating area of the equipment to help protect you from se
10. Instructions GG g GRACO XC Impulse Lubricators aii Uses an external power impulse to control the discharge of grease or oil lubrication to all lubrication points of sliding and roller bearings drive and transport chains sliding guideways open gears and seals For professional use only Not approved for use in European explosive atmospheres 75 psi 0 5 MPa 5 bar Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this manual Save these instructions See page 4 for model information C PROVEN QUALITY LEADING TECHNOLOGY Warnings The following warnings are for the setup use grounding maintenance and repair of this equip ment The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure specific risks When these symbols appear in the body of this manual refer back to these Warnings Product specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable ELECTRIC SHOCK HAZARD This equipment must be grounded Improper grounding setup or usage of the system can cause electric shock e Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment e Connect only to grounded power source All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations FIRE
11. canister with Lubricator does not discharge Dip switch setting was done a full lubrication canister the correct amount incorrect Set TIME dip switches 1 and 2 to correct setting 3A0416C 21 Parts Parts Miscellaneous Accessories Part No 123951 124279 124086 124087 124089 124090 124091 124092 124093 124100 124101 124102 124109 124113 124114 124115 124116 124119 Description MOTOR EM XC HARNESS cable power EM XP XC CLIP BRACKET plastic BRUSH pig hair 1 4 fnpt 3 4 BRUSH oil 1 x 1 5 BRUSH oil 1 x 2 4 BRUSH oil 1 x 4 BRUSH link chain CLAMP beam 1 BRACKET dual unit VALVE check oil throttle KIT accessory purge APPLICATOR chain felt BRUSH nylon 1 8 mnpt x 5 8 BRUSH nylon 1 8 mnpt x 2 KIT SA heavy green PADDLE open gear lube Mounting Brackets Part No 124094 124095 124096 124097 124098 124099 Description BRACKET mounting small BRACKET mounting medium BRACKET mounting large BRACKET mounting flat BRACKET mounting L BRACKET mounting bulk head Fitting Adapter Part No 124105 ADAPTER 1 4 fnpt x 1 4 mnpt 124106 ADAPTER 1 4 fnpt x 1 8 mnpt Description Pressure Relief Valve Part No 124107 124108 22 Description VALVE relief 1 8 m 5 Ib VALVE relief 1 8 m 1 Ib Qty ee L LLL ll L Ll Qty 1 1 i 1 Qty 1 1 Qty 1 1 Replacement Cap Part No
12. cation Canister 1 If a different size lubrication canister or dis charge period is going to be used change dip switches to reflect the new canister size and or impulse change See Table 1 page 13 2 Place drive unit on top of new lubrication canister until the teeth of both pieces are locked 3 Screw the cover of the drive unit onto the lubrication canister hand tighten only 4 Remove plug A from bottom of lubrication canister 5 Install lubricator unit into adapter B 6 Screw lubricator into the lubrication point hand tighten only DO NOT screw it in a second time NOTICE Never screw in the lubricator a second time or the self sealing threads will be damaged 7 For oil filled lubricators make sure the lubricator is installed vertically outlet point ing down 8 Plug cable back into lubricator FiG 10 20 FIG 10 9 The control will wait for a pulse to start dis charging Lubrication Canister Disposal a CE Dispose of hazardous fluid in approved con tainers and according to applicable guide lines Read the MSDS to know the specific hazards of the fluids you are using Storage When lubricators are not immediately installed they must be stored in a dry dust free sunlight protected room indoors 3A0416C Troubleshooting Troubleshooting AN QD Connect cable according to pin Wrong cable connection assig
13. ck the piston inside the canister The VOL switches 3 and 4 of the 4 way code switch match the correct size of the lubrication canister The TIME switches 1 and 2 of the 4 way code switch in the drive unit match the desired discharge impulse All components are properly assembled and screwed together hand tight 3A0416C To begin the discharge Plug power cable into lubricator FIG 8 Fic 8 During Operation e Carry out regular performance checks Check for possible leakages and the status of the lubricator e Regularly monitor the fill level of the trans parent lubrication canister 3A0416C Changing the Lubrication Canister Changing the Lubrication Canister When the red and green LED light up at the same time the lubrication canister is empty and should be replaced The drive unit and circuit board must always be protected from moisture to prevent dam aging these components Always change the lubrication canister in a dry place Removing Lubrication Canister 1 Unplug cable from lubricator FIG 9 FIG 9 2 To disconnect adapter from lubrication point follow pressure relief procedure provided on page 6 3 Unscrew and com pletely remove adapter B from the lubricator Adapter will be reused 4 Unscrew cover from drive unit 5 Remove drive unit from the lubrication control 19 Changing the Lubrication Canister Installing New Lubri
14. e made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract
15. ed lubricator must be installed ver tically outlet down e For horizontal mounting a bracket clip must be used to hold the lubricator in place A horizontal clip bracket part number 124086 is available from Graco See Parts page 22 e For vertical installations always use a sup port adapter part number 124105 is avail able from Graco See Parts page 22 e he grease nozzle of the lubricator has a npt 1 4 inch male thread If your application has a different thread you may need to use an adapter See Parts page 22 for a com plete list of available adapters e Do not overtighten the plastic thread of the lubricator e For all metal to metal connections i e extensions reducers etc make sure to use LOCTITE 243 semi tight screw lock ing Loctite is a registered trademark of the Loctite Corpo ration Direct Mounting Installation Refer to FiG 4 for examples of correct and incorrect direct mounting installations Correct er e N N N v N N N N Y 1 V S wa am Incorrect iv X 3A0416C Remote Mounting Installations Refer to FIG 5 FIG 7 for examples of correct remote mounting installations e Remote installations require a grease line Graco recommends using a 5 16 inch flexi ble hose e Select a position for the lubricator that is easy to access and protected from high pressure water jets falling materials corrosive chemicals and extreme tempera tures
16. est point of the application Must be at least 5 16 inch diameter tube OD Til TI O O gt 3A0416C Installation and Setup 17 Operation Installing Lubricator to Lubrication Point 1 Clean the lubrication point to remove any potential contaminants 2 Verify the thread of the lubricator corre sponds to the thread of the screw point 3 Install reducers extensions grease line etc if necessary 4 Verify Dip Switches are correctly set See Table 1 page 13 5 Prime the grease line and all accessories with the same grease that is contained in the lubricator See Parts page 22 fora complete list of available grease car tridges 6 Remove the plug A Operation Before operation verify e The lubricator does not have any visible damage e The lubricator canister is filled with the requested grease or oil e For oil filled lubrication canisters an oil throttle must be attached Install lubricator unit into adapter B Screw lubricator to lubrication point hand tight only NOTICE o ensure optimal lubrication Seal threads of all connecting parts with a suitable standard sealant Mount oil filled lubricators properly with the outlet pointing down Never screw in the lubricator a second time or the self sealing threads will be dam aged For remote mounting installations make sure bracket does not squeeze the lubrica tion canister as this could blo
17. g machines corrosive chemicals e extreme temperature e falling materials Preparing Lubricator for Installation The lubricator has a self protection mecha nism which shuts off the drive unit at counter pressures higher than 5 bar 72 5 psi Most bearings require 0 5 2 bar 7 2 to 29 psi pressure without tubes extensions angles etc Use the following procedure to check the counter pressure of the application prior to installation NO TE Be sure to use a lubricant cartridge that contains the same grease used in the application The best measurement results are achieved during operation Checking the Counter Pressure 1 Clean the lubrication point to remove any potential contaminants Install reducers extensions grease line etc if necessary Prime the grease line and all accessories with the same grease that is contained in the lubricator See Parts page 22 for a complete list of available grease car tridges Remove the plug A Install lubricator unit into adapter B Screw a pressure manometer into the lubri cation point dd FiG 1 page 11 3A0416C A pressure manometer is a simple device that measures pressure output To build a pressure manometer you need a pressure gage aa tee fitting bb and stop valve cc FIG 1 shows a correctly assembled pressure manometer connected to the lubricator and a lubrication point FiG 1 aa Pressure Gauge
18. ll accessories and grease lines must be primed pre filled Without this priming pre fill ing the lubricator would first have to fill the accessories with lubricant Example A tube that is one meter long requires about 28 cm of lubricant It would take the lubricator with a 12 month setting and an EM 120 grease canister about 3 months to fill this 1 meter tube FiG 2 illustrates one way to pre fill using a grease gun to dispense the grease 11 Installation and Setup Circuit Board Settings Function Display Red and green LED s Light Emitting Diodes are on the circuit board and visible through the transparent cover The following signals about operating conditions malfunctions are displayed by these LED s for the user Steady f System functions OK functions OK Lo EN for less than 30 seconds with Lubricator is Fal LS NN motor running Steady signal for more than 30 sec Malfunction error onds Green and Red Steady signal Lubricator unit is empty Change canister Setting Dip Switches 1 Unscrew and remove the cover of the drive unit 2 Use a small screwdriver or your finger to move dip switches to the desired position Refer to Table 1 e Dip switches land 2 marked TIME are used to set the discharge amount per impulse e Dip switches 3 and 4 marked VOL are used to set the lubrication canister size diis If the 4 way code switch does not corre A LED Red spond to the actual size of
19. lubrication unit could destroy electronics PLC Connection One Output Signal 5 G e G XA G ee 3 1 s ndjno eutuuay 9Td j yea1q ajqeo I uonounjjeui m uauM L YBIH ZO a indino co Adwe yun 21 uouM uBIH LO yndjno LO i G X G G ee pue elg sjnduJ Jeuruua 9d Aifidns uamod Ui I a Feel ueeb 771 Hl lt 99S0S Bjep uo l r jeubis VUA lqe 608 aqq pe 7 BA c lt pasn jou ae Z 8 pue Lg y elq ood Lg 1ndui o poeuip pog 1ndino j28uuoo L o al 3A0416C Component Identification PLC Connection Two Output Signals r L rw x Gm m 1 B sjndjno jeujwa 9 Td yeaig a qeo I I uonounjJeui uauM uBIH O O Aydwe pun 31 vo i uouM L uBiH ZO co e uonounj JEULIOU c s E CD uBIH LO LO L 4 A eee al pus 9 eta 98S0S pue ejep uo jeubis uea16 ou LLS 5 jeuondo Z1g LLa M zig S08 jeuBis pes ou 998 0ZL tog pesn jou SJE ZLA PUE 8 Lg ndul o Apjooeurp pog ndino peauuos Aep uo XLI 08 zog r LJ id sind euru Jd A adns 4amod f ul l 4 ere u iB E a ul H L lt I yym lqeO
20. nment page 6 Check pin assignment Break in cable Check voltage at plug Attach new cable Lubricator does not function Check power supply Make sure there is sufficient power avail able for the number of lubrica tors used Relay defect in machine Change relays Setting of VOL switch different than attached lubrication canis Lubricator signals system func tor tions OK green LED although Replace lubrication canister with lubrication canister is empty Partly filled lubrication canister a full lubrication canister was replaced by an almost empty lubrication canister Clogged tube and or connection Clean tube and connecting Lubricator signals system mal parts arts then shut off and restart functions red LED APA Counter pressure too high No power supply lubricator Replace lubrication canister with a full lubrication canister Set TIME dip switches 1 and 2 to correct setting Lubricator discharges too fast Wrong position of TIME switch Setting of VOL switch different than attached lubrication canis ter Replace with full lubrication can Almost empty lubrication canis Ster ter was replaced with a partially filled canister Lubricator signals end of dis charge red and green LED although the unit is not empty Heset peg was not pushed down Move drive unit a few teeth so during assembly reset peg is pushed down Replace lubrication
21. riginal purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will b
22. rious injury including eye injury hearing loss inhalation of toxic fumes and burns This equipment includes but is not limited to e Protective eyewear and hearing protection e Respirators protective clothing and gloves as recommended by the fluid and sol vent manufacturer CALIFORNIA PROPOSITION 65 This product contains a chemical known to the State of California to cause cancer birth defects or other reproductive harm Wash hands after handling Models Panno Output Application Output Application Part No Output Application 24E086 Ultra Spindle 4 3A0416C Component Identification Component Identification D F A B C A Plug D LED function display B Lubrication Canister E TCover NOTE Canister cannot be refilled F t Cable with plug C T Drive Unit Includes gear motor and t Reusable parts circuit board 3A0416C 5 Component Identification Pin Assignment Pressure Relief Procedure Pin Cable Assignment Color current 1 Cover lubrication point A and lubricator B with a heavy rag to absorb any fluid that black may leak out while loosening the adapter 4 Black LED red digital 2 Carefully unscrew support adapter D from the lubrication point A Lubrication Point Lubrication Canister Drive Unit Support Adapter OOU gt 6 3A0416C Component Identification iagrams D iring W TT O Incorrect connection of the
Download Pdf Manuals
Related Search