Genie 1500 User's Manual
Contents
1. YE 3 NES SCREW DRIVE GARAGE DOOR OPENER MODELS POWERLIFT 900 GPOWER 900 PowerMax 1200 1500 TriloG 1200 1500 OPERATION amp MAINTENANCE MANUAL Includes INTELLICODE 2 Remote Control Safe T Beam System must be installed to close door For use only with residential sectional or one piece overhead garage doors Homelink and Car2U compatible For Answers and Assistance 1 800 354 3643 Or visit www geniecompany com WARNING To reduce the risk of injury to persons or damage to property Use this opener only with a one piece or sectional door SAVE THIS MANUAL FOR FUTURE REFERENCE INSTALLER LEAVE THIS MANUAL WITH HOMEOWNER Genie Genie logo Intellicode Safe T Beam are registered trademarks of and SilentMax is a registered trademark of GMI Holdings Inc dba The Genie Company Homelink is a registered trademark of Johnson Controls Technology Company Car2U is a registered trademark of Lear Corporation The Genie Company 2011 PN 38082501312 09 2011 THIS PAGE LEFT BLANK TABLE OF CONTENTS Section ciis bete nai URER Page Safety Information ees 2 Important Safety Instructions 2 Safety Features Opener Features 3 Transmitter Compliance Statement 3 1 Getting Started Overview of Powerhead Controls 4 Programming Overview eene 4 Poster Rev2. BLUE PROGRAM 2 3 FLASHES BLUE 3 TIMES A Then the Current Speed setting for OPENING travel will display SEE CHART BELOW NOTE Depending on the criteria mentioned above you may not have the option to increase speed LOCKS IN OPENING SETTING Press either until you reach the Ta desired setting Press amp Release OFF FLASHES BLUE 3 TIMES Then the Current Speed setting for CLOSING travel will display SEE CHART BELOW NOTE Depending on the criteria mentioned above you may not have the option to increase speed LOCKS IN CLOSING SETTING FLASH BLUE you reach the UN desired setting Press amp Release Both LEDs FLASH s BLUE to confirm setting FORCE SETTINGS DONE LED indicator colors O Orr OQ Blue Purple Q Red Powerhead LEDs Speed Level LONGLED ROUND LED High REDO no Medium PuRPLE ff runi tow ew AO sc FLASH BLUE REFERENCE CIRCUIT WIRING DIAGRAM FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM Opener circuit wiring diagram This wiring diagram is for reference only A WARNING Opening Cover May Cause Electric Shock Disconnect power from opener prior to removing cover POWER CORD CHAIN MOTOR SCREW DRIVE MOTOR BLACK S y RED i nS u 999 STB BWC IWC or AWC CONNECTOR PRINTED CIRCUIT BOARD CHOKE STRIPED WHITE Purchased Separately INTELLIGENT WALL CONSOLE 060090020 WALL CONSOLE A WARN
3. CHART BELOW desired setting I 4 3 LOCKS IN SETTING Press amp Then the Current s Release DOWN FORCE BLUE SE SETTING will display FLASHING a Press either until you VN reach the WE desired setting BLUE LOCKS IN SETTING O e BLUE OFF OFF USE CHART BELOW O BLUE Press amp Both LEDs TURN Release BLUE then OFF confirms Force BLUE Settings are reset Force Level 1 Off Force Level 2 Force Level 3 Force Level 4 Force Level 5 Force Level 6 Force Level 7 Force Level 8 E O ai I 6 Ooj6 e Oje o o o h Force Level 9 9 2011 E 2011 The Genie Company 10 ADJUSTMENT GUIDE sPeEp serriNGS Speed settings are pre programmed at the factory for the maximum speed Speed settings should not need adjustment with this unit However travel speed for the opener can be adjusted to a slower speed in both the open and close directions To mimimize wear on heavier sectional doors NOTE One piece doors are automatically set to the slowest speed during Limits programming and cannot be adjusted There are 3 speed settings available for sectional doors Please note that speed may be affected by door weight and balance along with condition of door components and tracks SPEED ADJUSTMENT Press amp Hold for turn Blue BLUE ACTION LEDINDICATION RESULT 1 PROGRAM about 10 seconds O or until both LEDs BLUE Then release BLUE
4. and on the STBs provide a self diagnostic code if an operational problem exists Safe T Reverse Contact Reversing System Automatically stops and reverses a closing door within two seconds of contact with an object Automatic ForceGuard Control Automatically sets the force required to fully open and close the door for maximum safety Watch Dog Monitoring System Monitors the Safe T Beam system to ensure proper function ality and will automatically stop and reverse a closing door if a problem is detected sie Manual Emergency Release Manually releases door from door opener Used during a power failure or other emergency to allow manual opening and closing O gt Q O O E SmartSet Electronic Programming Easily adjust the programming to reduce opening speed to a desired rate vary limits and force and program new remotes Automatic Lighting System Two bulb lighting system supplies up to 200 Watts of light for safer evening exits and entries Turns ON when door is activated and automatically turns OFF 4 minutes later Integrated Motion Detection Not available on all models Select units have motion detection built into the powerhead Lights automatically turn ON when motion is detected for much safer movement through the garage Lights will turn OFF after 4 minutes of no motion 3 2011 The Genie Company OPENER FEATURES Yr INTELLICODE 2 Access Security System A new generation superio
5. let go Door should remain stationary or move very slowly f door moves quickly CONTACT A TRAINED DOOR SYSTEM TECHNICIAN Close the door Verify shuttle release lever is in the ENGAGED up position pull release handle toward opener and let go OPENER DISENGAGED Operate door using a remote or wall console Door will re attach itself to carriage assembly LUBRICATE DOOR HARDWARE Lubricate door rollers bearings and hinges Use silicone lubricant or lightweight oil 2011 The Genie Company 8 Lubricate the drive screw e Wipe off old grease using a lint free cloth Apply a light coating of silicon based grease For best results use Genie9 GLU R CORRECTIVE MAINTENANCE CHANGE LIGHT BULBS 4 amp WARNING Use extreme caution when working from a ladder or step stool When replacing light cover make sure wires are not pinched or near moving parts 1 Disconnect power to door opener Open powerhead light cover Remove light bulb s Replace light bulb s Do NOT use light bulbs with greater than 100 Watt rating Close powerhead light cover 2 Reconnect power to door opener Test light operation RESET OPEN CLOSE TRAVEL LIMIT Performing all ten 10 Limits Force setting steps page 5 erases previous Limits Force settings NOTE The opener will not close the door automatically unless the Safe T Beam System is installed and Limits are programmed DIS
6. los Estados Unidos y del Canad antes de usar los mismos Les metteurs sont conformes la r glementation am ricaine et canadienne compter de leur date de fabrication Aucune garantie n est stipul e indiquant qu ils sont conformes toutes les prescriptions juridiques d autres autorit s Si les metteurs sont utilis s dans d autres pays il incombe l importateur d en d terminer leur conformit aux lois et r gles locales pouvant diff rer de celles des Etats Unis et du Canada avant toute utilisation desdits metteurs Sendeger te entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der Herstellung Wir Ubernehmen keine Gew hrleistung f r die Einhaltung aller gesetzlichen Bestimmungen in anderen L ndern Sollen Sendeger te in anderen L ndern eingesetzt werden so muss der Importeur vor dem Gebrauch sicherstellen dass die Sendeger te auch solchen lokalen Bestimmungen entsprechen welche von den Bestimmungen der USA und Kanadas abweichen AULT bie EL BB ARE DS ESURU DL RECEIPT 725 8 SES o P e BUS ZIEL EE TRI Hte E Ate X PIU ASR ZH DR o MRR ESSE HABA FH E DA ae fe FH LZ BI T XE RE EIE 9 SERRE ACER 9 ZZ PE 3 75 ENR A hFVAS YI lk BUEHRUOXAUJAG88077 4 ORREL E Y LALR F2LAR3vVAE IRYAUJAJGREROQAT DOE OA ECES S 2 WE CS EGA PIAS YIS AVAGRAKO AFT WADE CARE SNIGE HO FIC TENEO VEU C 3150 E A 7 X 7 TCEMHSEYO 8 AG vg S 285 A E OER ICES SCC ze RERS UA Tni EHAS nut zu pcr AAAA AE ER
7. not occur in a particular installation If this equipment does cause harful interference to radio or television reception which may be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiver antenna Increase the separation between the opener and receiver Connect the opener into an outlet on a circuit different from that to which the receiver is connected Consult your local dealer PROGRAMMING INTELLICODE 2 REMOTES to Intellicode 1 previous model Openers The default setting of Intellicode 2 must be changed The LED color displayed on the remote indicates the IntelliCode mode Red IntelliCode 1 Green IntelliCode 2 LED INDICATION RESULT Da a button NOT prorammed to a new Intellicode 2 opener Press amp hold that button for until both the RED amp GREEN LEDs are ON Release Press the same remote button 3 times 3 Find the Learn Code Button and Learn Code Indicator LED on your door opener If your Door Opener has a black antenna wire and the serial number does not start with 10 or higher the Learn Code Button and Indicator LED are located near the antenna The light lens may need to be opened If you use an external receiver it may need to be opened to access the Learn Code Button and Indicator LED If Door Opener does not have an Antenna you h
8. opener has a Motion Detector sensor it will keep powerhead lights ON as long as motion is detected Sure Lock Button When Sure Lock is ON the powerhead cannot be activated by the wall console or a remote Press and hold for 5 seconds or until Indicator Light flashes to activate Sure Lock M Press and release to turn Sure Lock OFF Open Close Button Open and closes door from inside garage Sure Lock Button LOCK disables controls after door is completely closed UNLOCK allows controls to work normally Indicator Light Red indicator light is always ON When Sure Lock is ON the indicator light flashes Independent Light Control Button Controls door opener lights from inside garage Tip If the Wall Console is energized LED ON but the door does not respond to the OPEN CLOSE button verify FROM STBs FROM STBs FROM WALL CONSOLE FROM WALL CONSOLE the Console is SCZACTTICH wired to the OHIO BWC terminals J NOT NOT USED USED on the powerhead sp ac me NC MW 9 2011 3 MAINTENANCE amp TROUBLESHOOTING If you have any questions please do not hesitate to contact customer service at 1 800 35 GENIE or visit www geniecompany com IMPORTANT SAFETY INSTRUCTIONS 44 WARNING To reduce the risk of sever
9. or springs are broken CONTACT A TRAINED DOOR SYSTEM TECHNICIAN Basic monthly maintenance tasks e Contact reverse Safe T Beam System Check Door balance Lubricate Door Hardware CONTACT REVERSE TEST See page 5 4 amp WARNING Use wall console supplied with opener Other approved wall consoles may be available Unapproved or incompatible wall consoles can cause the opener to operate unexpectedly 9 2011 Safe T Beam STB SYSTEM CHECK Check that both the RED and GREEN LEDs are ON steady This indicates the system is working properly If both LEDs are not ON steady check the appropriate items below STB Red LED flashes Check for obstruction Check alignment Verify wire routing from STBs to STB connection in powerhead Check for signal interference from another Safe T Beam unit For multiple door installations No STB Red or Green LED displayed Check wiring and wire connections If the system appears to be working properly perform the check as follows 1 Start the door closing 2 Pass on object through the beam the door should stop and reverse to the fully open position DOOR BALANCE SPRING TENSION Perform the check as follows With the door closed pull release handle DOWN and let go to release door carriage assembly from drive system Raise and lower the door manually it should move freely and smoothly Raise door manually about 3 to 4 feet and
10. D Round LED Lona LED Possible Problem Normal operation None required OFF OFF Check power supply No response from unit Contact a trained door system technician ON RED ON RED m e STEADY STEADY Limits NOT set properly Reprogram Limits see page 5 ON RED ON RED Unplug unit wait 5 seconds plug in Contact a trained door system FLASHING FLASHING Component failure technician ON BLUE FLASHING Remote NOT programmed Program remote see page 6 Program remote using IntelliCode9 ON PURPLE IntelliCode9 1 remote NOT 2 remote see page 6 then program FLASHING Orr programmed IntelliCode9 1 remote using instructions on page 6 Safe T Beam physical ON RED BEE obstruction Remove obstruction recheck unit FLASHING Safe T Beam signal Check alignment of Safe T Beam pair interference and nearest other Safe T Beam pair Door contact in up or down i ON RED travel Remove obstruction OFF FLASHING Door component failure Check door spring track rollers hinges detected and fixtures ON RED DO NOT unplug unit STEADY Wait until LED clears before operating POWERLIFT 900 GPOWER 900 POWERMAX 1200 7 1500 TRILOG 1200 7 1500 LIMITED WARRANTY GMI Holdings Inc d b a The Genie Company Seller warrants to the original purchaser of the below identified garage door opener POWERLIFT 900 GPOWER 900 PowerMax 1200 1500 or TriloG 1200 1500 Product subject to all of the terms and conditio
11. ENGAGING AND ENGAGING CARRIAGE OPENER N DISENGAGED TO DISENGAGE PULL TO ENGAGE PULL DOWN ON THE RELEASE DOWN AND TOWARD HANDLE AND LET GO THE OPENER THEN LET GO REMOTE BATTERY REPLACEMENT Replace remote battery with a CR 2032 coin cell battery 1 Open the remote case using a washer or coin that fits into the slot at the top of the remote 2 Replace battery 3 Align components and snap case closed 9 2011 The Genie Company 9 2011 ADJUSTMENT GUIDE rorce SETTINGS CAUTION Door closing force is FACTORY set and requires no adjustment for normal operation Never adjust the force settings to compensate for damage including an unbalanced door binding door track or broken spring Perform monthly CONTACT REVERSE TEST See page 7 Force settings are pre programmed at the factory and learned during the Open Close Limit settings steps For normal use these settings should not need adjustment with this unit However conditions possibly requiring adjustment are 1 Doors with very stiff weather seals 2 Doors that start down STOP andreverse before closing 3 Doors that start up but STOP before they completely open FORCE ADJUSTMENT 1 Press amp hold US 2 0 2 RED BLUE s OFF OFF FLASHES 3 TIMES both up and down buttons 2 seconds or until round Then the Current UP FORCE LED turns Red SETTING will display SEE CHART 2 Press either until you reach x USE
12. ENIECOMPANY COM Checkto make sure chain belt is not broken or OFF its pulley Check FORCE ADJUSTMENT See page 10 Check all remotes Replace remote battery with good one See page 9 Program remote to powerhead See page 6 Relocate remote inside car and or point remote at garage door Replace battery See page 9 Reposition door opener antenna Remote LED does not come ON with button push replace battery See page 9 Eliminate possible competing signals satellite radio FiOS TV Ifa NEW installation check Door Arm position Refer to Installation poster or download poster from WWW GENIECOMPANY COM Checkif Limits are properly set See page 5 amp 9 Check if Safe T Beam Red LED is flashing See page 8 Check Safe T Beam system for beam obstruction or misalignment of lenses See page 8 Check garage door for binding f an operational problem exists and opener will not close The opener can be forced to close as follows Press and hold the wall console button until door is completely closed Check for interference from adjacent Safe T Beam units Contact The Genie Company at 1 800 35 GENIE Check Safe T Beam wire connections at powerhead See page 8 STB Instruction Poster or website Check Limits are properly set See page 5 amp 9 Check CONTACT REVERSE See page 5 Check garage door for binding Check closing FORCE adjustment See page 10 Check Limits
13. ES STOO OL SPARA Heo LC 7 El CHE HEH DE HAC s AR ejot HAS AAU die EHAEO 71 EFEIE AHAN ABE SS SUAE AS ol Ol HA SAAE RFA E cl SATTES IAA Aa EAA major RL E yho LC 9 2011 1 OVERVIEW OF POWERHEAD CONTROLS This section describes the simple programming functions Use this page to familiarize yourself with the buttons and LED indicators used to program the opener NOTE These A and buttons are for programming use only Do NOT use these buttons to operate the opener There are three programming buttons and two lights LEDs on the powerhead Each of the buttons are used to enter and complete the setup programming The LEDs indicate status or a function change by illuminating ON OFF or ON flashing in one of three different colors BLUE RED or PURPLE CloseTravel OpenTravel ROUND LED Butt Facing Indicator PROGRAM utton Garage Door I LONG LED SET _ Indicator Located on bottom of Powerhead PROGRAM Enters into and selects programming menus SET ie a Multi function move door during programming x amp advance through menus Both LEDs can be Red Blue Purple or off depending on the programming step you are performing INFRARED PROTECTION FUNCTION he Safe T Beam has no effect on the door during an opening cycle If the Safe T Beam detects an obstruction when trying to close the door it will not allow the door to move When the garage door is closing if Safe T Beam is interrupted
14. ING MOTION DETECTOR OPTICAL SENSOR C RED BLACK RED GREEN i YELLOW L SOME MODELS DO NOT COME WITH THIS FEATURE ELECTRICAL SHOCK 11 2011 The Genie Company 9 2011 TROUBLESHOOTING GUIDE OPERATION PROBLEM Opener does NOT run from wall console Opener runs but door does NOT move Opener works from wall console but NOT from remote Remote has less than 25 feet operating range or no operation Door starts down then STOPS and goes back up OR Safe T Beam System malfunction Door starts down then STOPS before it is closed OR Door will only open Door starts up but STOPS before it is completely open Door will only run closed Door opener starts for no reason Noisy operation Door opener runs slow 9 2011 FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM WHAT TO DO Check power source Plug a lamp into outlet used for powerhead If lamp works power source is OK f not check fuse or circuit breaker If power is OK Check connections at powerhead terminals and at wall console Limits must be set with door arm connected to door Check if wall console Sure Lock is ON Turn Sure Lock OFF amp check operation Check for reversed broken or cut wires Staples can cut insulation and short wires Repair or replace Make sure carriage is engaged to chain or belt bullet See page 9 Refer to Installation poster or download poster from WWW G
15. are Opoperly set See page 5 Be sure door opener and springs are in good repair properly lubricated and balanced Check opening FORCE adjustment See page 10 A WARNING If you suspect a problem with the garage door hardware or springs contact The Genie Company at 1 800 35 GENIE Check Limits are properly set See pages 5 amp 9 e Check Sure Lock Sure Lock should be OFF for normal operation See page 7 Check door balance condition and door spring Check opening FORCE adjustment See page 10 A WARNING If you suspect a problem with the garage door hardware or springs contact The Genie Company at 1 800 35 GENIE Button stuck on wall console or remote Was a remote lost or stolen Erase all remotes from powerhead memory and program new remotes See page 7 Besure all door fasteners are tight Be sure garage door is in good repair properly lubricated and balanced Be sure opener is in good repair Check operating condition of door See page 8 Door may need professional repair adjustment sthis opener installed on a one piece door Normal speed for one piece door islowest speed setting If carriage travel is less than 6 feet opener configures programming for a one piece door Contact The Genie Company at 1 800 35 GENIE concerning door speed 2011 The Genie Company TR OUB LE S H OOTI N G GUI D E POWERHEAD LEDs FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM Powerhead LE
16. ave an External Receiver The External Receiver cover must be removed to access the Learn Code Button and Indicator LED Press the Red Indicator LED BLINKS L ean Code Button Button Press the same Red Indicator LED OFF remote button twice Press the same remote button again zi DOOR MOVES REMOTE BUTTON IS PROGRAMMED TO OPENER Follow the TOP 2 steps above to shift back to Intellicode 2 9 2011 2011 The Genie Company 6 OPTIONAL PROGRAMMING IntelliCode 1 or 2 wireless keypad ACTION LED INDICATION RESULT 1 Enter your PIN on the wireless keypad ROGRAM O O BLUE OFF OFF PURPLE FLASHING Both LEDs OFF confirms communication is established with operator Press amp Hold for 2 seconds or until round LED turns blue then OFF Then Long LED flashes purple 4 Press amp release 2 times O OFF F F nw Door moves Genie Intellicode 2 Wireless Keypad comes with a complete set of instructions 5 Press amp release LOST OR STOLEN REMOTE CLEARING MEMORY 1 PROGRAM Round LED BLUE then OFF Long LED FLASHING Press amp hold O O 2 seconds BLUE OFF OFF PURPLE Release FLASHING 2 Press amp hold BOTH open O and close BOTH BLUE FLASHING o OFF OFF REMOTE CLEARED FOR REPROGRAMMING To verify memory is cleared try to operate the garage door using one of your remote devices The opener should not respond WO buttons together EJ Releas
17. by person or obstacle the garage door will stop its downward travel and reverse automatically to its fully opened position If the Safe T Beam System fails loses power or is installed improperly press and hold the wall console open close button until the door reaches its fully closed position If you release the open close button on the wall console during the closing movement the door will reverse automatically to its fully opened position 9 2011 Begin here ONLY AFTER completing assembly and installation of the opener Review the Assembly amp Installation Poster to ensure all steps have been performed There are no assembly or installation steps included in this manual Contact your Genie Professional Dealer for an installation poster if needed or call 1 800 35 GENIE You may also visit www geniecompany com to download a pdf file Before you begin Programming check to make sure there are no objects in the garage door opening Programming Overview There are four Powerhead program menus Remote Program Default menu Limits Program Force Program Speed Program ADJUSTMENT OF FORCE amp SPEED SETTINGS IS ON PAGE 10 IN THE MAINTENANCE amp TROUBLESHOOTING SECTION Force settings are set at the factory and do not normally require operator programming but can require minor adjustment under certain conditions See Troubleshooting Speed settings are set at the factory and are self ad
18. e NOTE Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad All remotes and wireless keypads must be reprogrammed Your door opener will no longer recognize any signal received from a missing remote 7 2011 The Genie Company WALL CONSOLE OVERVIEW This opener has a Serial Number sticker in which the serial numbers begin with 10 or higher THE GENIE COMPANY Residential Door Operator 120V 60HZ 5A N 10XXXX LUAM XXXXXXX QU aN R 800 35GENIE OR WWW GENIECOMPANY COM Wall consoles from other manufacturers may not work with openers of these serial number groups Genie Series wall buttons and Series Il wall consoles will not work with openers of this serial number group Use only the Series IIl wall console provided with this unit Wall console has three buttons and one indicator light Indicator Light Indicator light will display Red when wall console is properly wired and Sure Lock is OFF When SureLock is ON indicator light flashes Open Close Button Use this button to open or close garage door When Sure Lock is ON the Open Close button will CLOSE door only Note Constant button pressure in the CLOSE mode will override error responses in the powerhead and close door Independent Light Control Button Use this button to turn powerhead lights ON Powerhead lighting will remain ON until this button is pressed again or a door action has been completed Note If
19. e Setting eene 10 CHANGING Speed Setting asesinos 10 Troubleshooting Guide 11 12 Warranty uoo iEn 12 REFERENCE Wiring Diagram 13 OPENER MUST BE INSTALLED WITH THE INCLUDED WALL CONSOLE Safe T Beam SAFETY REVERSE SYSTEM MUST BE INSTALLED TO CLOSE DOOR 9 2011 SAFETY INFORMATION OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large heavy objects that move with the help of springs under high tension and electric motors Since moving objects springs under tension and electric motors can cause injuries your safety and the safety of others depend on you reading the information in this manual If you have questions or do not understand the information presented call your nearest trained door system technician or visit our website The following Safety Alert symbol and signal words are used throughout this manual to call attention to and identify different levels of hazard and special instructions This is the safety alert symbol This symbol alerts you to A potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and the word DANGER WARNING or CAUTION DANGER indicates an imminently hazardous situation which if NOT avoided will result in death or serious injury WARNING indicates a potentially hazardous
20. e injury or death READ AND FOLLOW ALL INSTRUCTIONS 2 Never let children operate or play with the door controls Keep the remote away from children Always keep the moving door in sight and away from people and objects until the door is completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR NEVER GO UNDER A STOPPED PARTIALLY OPEN DOOR lest opener monthly The door MUST reverse on contact with a 1 1 2 high object or a 2 x 4 board laid flat at the center of the doorway on the floor After adjusting either the force or the limit of travel retest the door opener Failure to adjust the opener properly may cause severe injury or death When possible use the og release only when the door is closed Use caution when using this lea with the door open Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of severe injury or death KEEP DOORS PROPERLY BALANCED See your garage door Owner s Manual An improperly balanced door increases the risk of severe injury or death Have a trained door system technician make repairs to cables spring assemblies and other hardware s SAVE THESE INSTRUCTIONS WARNING Garage door hardware springs cables brackets pulleys etc are under extreme pressure and tension DO NOT attempt to repair or adjust door springs or any hardware and DO NOT OPERATE garage door automatically or manually if door is improperly balanced
21. ges so the above limitation or exclusion may not apply to you Claims under this warranty must be made promptly after discovery and within the applicable warranty period To obtain warranty service you must contact Genie customer service and provide proof of the date and location of Genie customer service and provide proof of the date and location of purchase and identification as the original purchaser Call Genie Customer Service toll free at 1 800 354 3643 to speak with a trained representative Purchaser must allow seller a reasonable opportunity to inspect Product claimed to be defective prior to removal or alteration of its condition Upon determination by Seller that the Product or any part thereof is defective during the applicable warranty period which may require purchaser to return the Product to Seller at purchaser s expense Seller will supply the purchaser with replacement parts or at its option a replacement Product shipping and handling of any replacement part s or replacement Product also at purchaser s expense Seller may use new or reconditioned parts or a new or reconditioned Product of the same or similar design There are no established informal dispute resolution procedures of the type described in the Magnuson Moss Warranty Act PURCHASER REMOTE CONTROL MODEL INSTALLATION ADDRESS DEALER NAME DATE PURCHASED SERIAL NUMBER DEALER ADDRESS OPENER MODEL P900 228 13 2011 The Genie Company 9 2011
22. iew Infrared Protection Function 4 2 Programming Limits and Force eene 5 Contact Reverse Test sene 5 Programming Intellicode 2 Remote to Powerhead eene 6 Optional Programming Powerhead to HomeLink Car2U Intellicode 1 Remotes or Wireless Keypads see 6 Programming New Remotes to Previously Installed Genie Intellicode 1 Garage Door Openers sss 6 FCC and IC Certification sss 6 Lost or Stolen Remote 7 Wall Console Overview 7 3 Maintenance amp Troubleshooting Important Safety Instructions 8 Monthly Routine seen 8 Safe T Beam System Check 8 Door Balance Spring Tension 8 Contact Reverse Test Reference 8 Corrective Maintenance sess 9 Changing Light Bulbs carsscsccasssssscostsnnssussetessnstesosesttesentsstantss 9 Remote Battery Replacement sss 9 Belt Tensioning Adjustment ee 9 Travel Limit RES GU even aperto iam TOR cra dor ar 9 Engage amp DISENGAGE Carriage 9 Adjustment Guide 10 Changing Forc
23. in commercial or industrial building applications This warranty does not apply to any unauthorized or improper installation alteration or repair of the Product or to any Product or component which has been damaged or deteriorated due to misuse abuse neglect accident failure to provide necessary maintenance normal wear and tear or acts of God or any other cause beyond the reasonable control of Seller and does not cover batteries missing or damaged parts from clearance or open box sales or repairs or maintenance to door components ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN TIME TO THE APPLICABLE WARRANTY PERIOD REFLECTED ABOVE NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to youIN NO EVENT SHALL GMI HOLDINGS INC OR ITS PARENT OR AFFILIATES BE RESPONSIBLE FOR OR LIABLE TO ANYONE FOR SPECIAL INDIRECT COLLATERAL PUNITIVE INCIDENTAL OR CONSEQUENTIAL DAMAGES even if Seller has been advised of the possibility of such damages Such excluded damages include but are not limited to loss of use cost of any substitute product or other similar indirect financial loss Some states do not allow the exclusion or limitation of incidental or consequential dama
24. justing when needed Speed Settings do not normally require manually initiated changes 2011 The Genie Company 4 2 PROGRAMMING LIMITS FORCE CONTROL 1 ON WALL CONSOLE Press amp Door fully closes Release Open Close button 4 amp WARNING Make sure doorway is in view and clear of obstacles and people to avoid injury or damage to property DO NOT operate this unit from wall console before LIMITS and FORCE are set Severe damage to the opener can occur The bullet MUST be engaged to carriage BEFORE setting limits See Installation Poster if provided or call Customer Service at 800 35 GENIE or visit www geniecompany com NOTE If bullet has NOT been engaged to Press amp Release the carriage do so now See page 9 Open Close button Door fully opens Please note that there is a 30 second timeout between each programming step If you see two flashing RED LEDs you have initiated a timeout In the event of a timeout you must restart at beginning 4 amp WARNING TRAVEL LIMITS A moving door can cause serious injury or death DOWN LIMIT Keep people clear of opening while door is moving ACTION LED INDICATION RESULT 1 Do NOT allow children to play with opener including wall console remote or wireless keypad During programming door opener could begin to run so stay away from moving door and its parts Long LED turns Blue then flashes Press amp hold V 2 second
25. ns hereof that the Product and all components thereof will be free from defects in materials and workmanship for the following period s of time measured from the date of purchase MOTOR GEARBOX Seller warrants the motor gearbox for the LIFETIME of the product BELT Seller warrants the belt for a period of FIFTEEN 15 YEARS CHAIN Seller warrants the chain for a period of FIVE 5 YEARS CORE UNIT PARTS Seller warrants all other parts and components of the Core Unit for a period of FIVE 5 YEARS ACCESSORIES Seller warrants all accessories for a period of ONE 1 YEAR Lifetime shall mean for as long as the original purchaser owns the home in which the product is originally installed The Core Unit consists of the powerhead wired wall control Safe T Beam system J Arm and rail Seller s obligation under this warranty is specifically limited to repairing or replacing at its option the Product or any part thereof which is determined by Seller to be defective during the applicable warranty period Any labor charges are excluded and will be the responsibility of the purchaser This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty is made to the original purchaser of the Product only and is not transferable or assignable This warranty applies only to Product installed in a residential or other non commercial application It does not cover any Product installed
26. oting page 13 Once the Contact Revese Test is complete continue with programming Remotes 5 2011 The Genie Company 9 2011 PROGRAMMING REMOTES to New Intellicode 2 Openers All type remotes program in the same way Bring remote s to powerhead location For Car2U and HomeLink park car outside the garage with the ignition key in the ACCESSORY position Each button must be programmed individually following steps below ACTION LED INDICATION RESULT 1 Press amp Hold for lo 2 seconds or until LJ m s round LED turns blue x PURPLE Choose a button on your Both LEDs Off remote device Press amp O release it twice OFF OFF PURPLE OFF STEADY Press amp Release that same DOOR MOVES button again REMOTE BUTTON IS PROGRAMMED NOTE For additional openers repeat the steps above using a different remote button for each FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will
27. r encryption system that enhances the security of the door opener by continuously changing the access code each time the remote is used The door opener responds to each new code only once An access code copied from a working system and tried again will not control the door opener Wall Console Series III Operates door opener from inside garage The Wall Console has an Indicator Light with Open Close Sure Lock and Independent Light Control buttons IN HomeLink COMPATIBLE www homelink com HomeLink and Car2U compatible Refer to the programming instructions on page 6 TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture No warranty is made that they comply with all legal requirements of any other jurisdiction If transmitters are to be used in another country the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canad en la fecha de fabricaci n Ninguna garant a se da que cumplan con todas las reglamentaciones legales de ninguna otra jurisdicci n Si los transmisores se van a utilizar en otro pa s el importador debe determinar si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de
28. s or until lo RE en LEDs react Release BLUE FLASHING The Force and Limit settings MUST be COMPLETED Press amp hold before performing Contact Reverse Test until door is fully DOOR FULLY OPEN 1 Test closed Then release ACTION INDICATION RESULT Both BLUE then LEDs Off confirms limit set 1 O Press amp BOTH FLASH BLUE orr OFF Release the a DOOR OPENS Open Close During the initial setting button of the limits the LEDs will RED turn to RED NOT OFF RED Ea re Long LED turns Blue Then Long LED OFF Placea2 x4 a A oes amp hold N Round LED OFF Round LED Flashing board laid flat 2 seconds or until O under center of LEDs react Release w p PARING door opening Press amp h ol d ee Aa Ws until door is fully DOOR FULLY CLOSED open Then release DOOR CLOSES Press amp Both BLUE then LEDs Off confirms limit set Press amp e When door contacts board Release O r O Release the Laat it must stop and reverse direction Open Close Te within 2 seconds to the full OFF y BOTH FLASH BLUE wa i i a eu button A open position 2adiusiment ifnesdad f the door stops before it contacts the board SET FORCE NEXT or it does not reverse it may be due to an improperly set down limit Repeat TRAVEL LIMITS program and Test again Repeat as needed until door passes test For further help refer to Maintenance amp Troublesho
29. situation which if NOT avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if NOT avoided may result in injury or property damage The word NOTE is used to indicate important steps to be followed or important considerations IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Record Effect Prevention Keep people clear of opening AAWARNING mail door is moving Could result in Do NOT allow children to Benen play with Door Opener Serious Injury Do NOT operate a door that jams or has a broken spring A Turn OFF power before WARNING removing opener cover When replacing cover make sure wires are NOT pinched or near moving parts Opener must be fully grounded Could result in Death or Serious Injury Do NOT try to remove install repair or adjust springs or anything to which door springs A WARNING are fastened such as wood blocks steel brackets cables or other like items Installations repairs and adjustments must be done by a trained door systems technician using proper tools and instruction Could result in Death or Serious Injury 2011 The Genie Company 2 SAFETY FEATURES Safe T Beam STB Non Contact Reversing System Puts an invisible beam across the door opening The door stops and reverses to the full open position if anything passes through the beam LED indicator lights on the powerhead
Download Pdf Manuals
Related Search