GE ZGU3650 User's Manual
Contents
1. Min From Front of Countertop Measure carefully when cutting countertop Make sure sides of opening are parallel and rear and front cuts are exactly perpendicular to sides e The Monogram gas updraft cooktop is designed to fit in a 36 or larger base cabinet e The countertop cutout for cooktop must be 34 1 2 wide 18 1 8 deep Allow at least 4 5 8 clearance between back of cutout and wall Allow at least 8 13 16 clearance from right and left side of cutout to adjacent wall Allow at least 2 1 4 clearance between front of cutout and front edge of countertop Installation Preparation Gas Updraft Cooktop e 1 2 NPT x 3 4 I D or 1 2 LD flare union adaptor for connection to regulator e 5 foot AGA certified flexible metal appliance connec tor 3 4 or 1 2 I D to match gas e Gas resistant pipe supply line joint sealant If required by local codes use solid pipe with fittings Note Purchase new flexible line DO NOT USE OLD PREVIOUSLY USED FLEXIBLE LINE e Cooktop requires 3 free space below countertop e If installing cooktop above a cabinet with drawers it may be necessary to use a shorter length drawer to allow clearance for gas connection e In some cases two 3 8 I D 45 elbows and a pipe nipple may be added between regula tor and cooktop to move regulator further back in order to avoid interference with drawer Power supply locations2. ae Burner Cap ds Burner Head S Burner Bowl Installation Gas Updraft Cooktop Regulator Solid Piping or Flexible Connector Shut Off D Valve FA Pipe Stub IMPORTANT Disconnect the cooktop and the individual shut off valve from the gas supply piping system during any pressure testing of that system at test pressures greater than 1 2 psig Isolate the cooktop from the gas supply piping system by closing the individual manual shut off valve to the cooktop during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig Medium Head And Cap Medium Head Small Head And Cap 2 And Cap Medium Head E o Large Head And Cap And Cap Front Check for proper ignition Push in one control knob and turn 90 to HIGH position The igniter will spark and the burner will light the igniter will cease sparking when the burner is lit First test may require some time while air is flushed out of the gas line Turn knob to OFF Repeat the procedure for each burner 7 36 Monogram General Electric Company Louisville RY 40225 NOTE While performing installations described in this book safety glasses or goggles should be worn To obtain specific information concerning any Monogram product or service call GE Answer Center consumer information service at 800 626 2000 any time day or night For Monogram local
3. Gas supply These cooktops are designed to operate on natural gas at 4 of water column pressure or on LP gas at 10 of water column pressure These cooktops are shipped from the factory set for natural gas If you decide to use this cooktop with LP gas conversion adjustments must be made by a service technician or other qualified person JXLP56 conversion kit is required for LP operation e The pressure regulator must be connected in series with the manifold of the cooktop and must remain in series with the supply line regardless of type of gas being used For proper operation the maximum inlet pressure to the regulator must be no more than 10 water column pressure for natural gas and 14 water column pressure for LP gas e When checking the regulator the inlet pressure must be at least 1 greater than the regulator output setting If the regulator is set for 4 of water column pressure the inlet pressure must be at least 5 If the regulator is set for 10 of water column pressure the inlet pressure must be at least 11 For ease of installation and if local codes permit the gas supply line into the cooktop should be 1 2 or 3 4 ID flexible metal appliance connector three to five feet long Note Purchase new flexible line DO NOT USE OLD PREVIOUSLY USED FLEXIBLE LINE e Make gas connection through rear wall or on cabinet floor at rear as illustrated Installation Preparation Gas Updraft Co
4. current Design Information Models Available s smnsssssosssrrrerrrrrrrerrrrrrrrrrrrrrrr rna 3 Advance Planning gt siss scsscisjwsssnsisernsorssnisrnrsnreen 3 Dimensions and Clearances eeeeeeeeeea 3 Installation Preparation Tools and Materials Required 4 Cut the Opening ssrtssssn sssrinin 4 Power Supply Locations s ssssesssesssrssrrssserenernnnn 5 Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owners Manual for warranty information For Monogram local service in your area 1 800 444 1845 For Monogram service in Canada 1 888 880 3030 For Monogram Parts and Accessories call 1 800 626 2002 Natural Gas Installation Code CAN CGA B149 1 or the current Propane Installation Code CAN CGA B149 2 and with local codes where applicable e This cooktop has been design certified by the American Gas Association according to ANSI Z21 1 latest edition and Canadian Gas Association according to CAN CGA 1 1 latest edition e Your cooktop must be electrically grounded in accordance with local codes or in the absence of local codes in accordance with the National Electrical Code ANSI NFPA 70 latest edition In Canada electrical grounding must be in accordance with the current CSA C22 1 Canadian Electrical Code Part I and or local codes Installation Install COOKtOp
5. GE Monogram Installation Instructions 36 Gas Cooktops Models ZGU3650 Contents Before you begin Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES NOTE TO INSTALLER Be sure to leave these instructions with the Consumer NOTE TO CONSUMER Keep these instructions with your Owners Manual for future reference This appliance must be properly grounded See Power Supply page 5 Cet appareil doit tre correctement mis la terre Voir lt lt Alimentation lectrique gt gt a la page 5 If you have a question concerning the installa tion of this product call the GE Answer Center Consumer Information Service at 800 626 2000 24 hours a day 7 days a week If you received a damaged cooktop you should immediately contact your dealer or builder FOR YOUR SAFETY If you smell gas 1 Open windows 2 Don t touch electrical switches 3 Extinguish any open flame 4 Immediately call your gas supplier FOR YOUR SAFETY Do not store or use combustible materials gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance e Installation of this cooktop must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 latest edition In Canada installation must conform with the
6. okto p e Remove packaging from the cooktop e To insure a good fit position the cooktop over the cutout opening and carefully lovver into place Check edges all the way around to be sure all cutout edges are concealed and there are no gaps e Carefully lift and remove the cooktop 1 16 e Cut a 3 16 gasket strip in half Peel off the backing and apply to the underside of the glass cooktop edge on each side at least 3 8 from the back and as close to the edge as possible without protruding e Apply the other gasket strip to the underside of the glass at the front of the cooktop e Remove remaining adhesive backing e Position the cooktop over the opening making sure that the power cord is dropped into the cabinet e Lower the cooktop into the cutout pressing gently and evenly to seat Installation Gas Updraft Cooktop a Countertop vr vv Note If the cooktop is installed in a 36 base cabinet the mounting brackets cannot be used because of interference with the cabinet sides In this case the cooktop can be secured to the cabinet with angle brackets not supplied Remove one screw at the bottom of the cooktop body on both sides and secure the bracket with those screws Then secure the brackets to the cabinet sides e Insert hold down bracket into highest slots on the right and left sides of the cooktop Cooktop has three slots the highest available will depend on
7. oktop Right of Cutout 5 8 Forward of Back of Cutout Electrical supply This cooktop features pilotless electric ignition for energy savings and reliability It operates on a 120 volt 60 Hz power supply A separate circuit protected by a 15 amp time delay fuse or circuit breaker is required e A properly grounded 3 prong receptacle should be located within reach of cooktop s four foot power cord IMPORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has correct polarity Where a standard two prong wall receptacle is encountered it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three prong wall receptacle Do Not Under Any Circumstances Cut Or Remove The Third ground Prong From The Power Cord Do not use an extension cord Note If the cooktop is installed into a 36 St E base cabinet the pressure regulator MUST BE installed to the bottom of the cooktop before the cooktop is placed into the cabinet Install Co
8. service in your area call 1 800 444 1845 NOTE Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are Pub No 49 80000 1 subject to change without notice Part No 183D5580P074 2000 GE Appliances N D 505 5 00 Printed in Mexico
9. sssssoscosovenseosnnossonensussteserereensnnnren 6 Install Pressure Regulator ssssosssosssssnnnsnnen T Connect Electrical ssssssssseossseseresesseserennnrrr 7 Assemble Burners Check Ignition 7 Dimensions and clearances Advance planning ZGU3650 36 gas updraft cooktops For those who prefer gas heat for cooking the Monogram built in gas updraft cooktop offers the cooking method of choice These cooktops are only 3 deep and can be installed over cabinet drawers Design Information Gas Updraft Cooktop These models are shipped for natural gas operation They can be converted to liquid propane Order JXLP56 conversion kit 4 5 8 Min to Vertical Combustible Surface je 7 3 7 8 Min to Vertical Combustible Surface When Installed 8 13 16 Min 34 1 2 to Wall 21 M n When Installed Both Sides 2 Min to Front of Countertop When Installed e Refer to Installation Preparation for information on appropriate placement and necessary clearances when planning installa tion cooktop when possible e Avoid placing cabinetry directly above e If cabinetry is used above cooking surface Use cabinets no more than 13 deep Maintain 30 minimum clearance between cooktop and unprotected cabinets directl
10. the thickness of the countertop e Secure the brackets to the underside of the countertop with screws provided Step Install Pressure Regulator Step Connect electrical Step Assemble burners check ignition Make sure slot in burner head is positioned over electrode e Install the supplied pressure regulator and nipple in the gas line as close to the cooktop inlet as possible Allowances for ventilation ducting may be necessary Make sure the regulator is installed in the right direction e Install a manual shut off valve in the gas line in an easily accessible location Note Instead of using solid piping to connect to pressure regulator an approved flexible metal appliance connector may be used between the pipe stub and the shut off valve and the pressure regulator if local codes permit Appropriate flare nuts and adapters are required at each end of the flexible connector e Turn on the gas Check for leaks using a liquid leak detector at all joints in the system the pressure test nipple is adjacent to the gas inlet pipe on the rear right hand side of the cooktop bottom Ne NU Do not use a flame to check for gas leaks DA IL NE FAUT PAS UTILISER DE FLAMME POUR VERIFIER S IL YA DES FUITES e Plug power cord into properly grounded receptacle e Assemble burner as shown Check to be sure that burner heads are securely seated and caps are positioned as shown 7 Grate
11. y above cooktop If clearance is less than 30 protect cabinet bottoms with flame retardant millboard at least 1 4 thick or gysum board at least 3 16 thick covered with 28 gauge sheet steel or 02 thick copper Clearance between cooktop and protected cabinetry must not be less than 24 An exhaust hood that projects at least 5 beyond front of cabinets can reduce risk of burns caused by reaching over heated surface units Working areas adjacent to the cooktop should have 18 minimum clearance between countertop and cabinet bottom e Use the Monogram gas updraft cooktop with any 36 or wider exhaust hood if desired no special ventilation is required e Installation must conform with local codes In the absence of local codes the gas cook top must comply with the National Fuel Gas Code ANSI Z223 1 latest edition Tools and Materials Required Cut the Opening e Self adhesive gasket supplied e Two clamping brackets and screws supplied e Gas pressure regulator supplied e Large flat blade screwdriver e Saw 8 13 16 Min to Side Wall 4 5 8 Min Cutout to Vertical Combustible Surface Caution Wallcoverings countertops and cabinets should withstand 200 F heat generated by the cooktop e Carpenter s square e Pipe wrench e Manual gas line shut off valve 03 4 NPT x 3 4 I D or 1 2 NPT x 1 2 LD flare union adaptor for connection to supply line 2 1 4
Download Pdf Manuals
Related Search