GE EDW3000G02 User's Manual
Contents
1. KEYPAD AT ANYTIME TO EXIT Service Mode Test Matrix Keypad Description Time in Seconds Activates Water Valve 50 Activates Heating Element 600 Activates Main Pump 75 Activates Detergent Module 60 Activates Drain Pump 75 Activates the following in order Status LEDs Wash LEDs Start Reset and Option LEDs 3 seconds each cycle 2 Opens Active Vent 1 Closes Active Vent START RESET Used to EXIT Service Mode NOTE After 15 minutes of inactivity the service mode will automatically turn off NOTE Component will be activated for indicated time Component may be deactivated by pressing the same keypad that was pressed to activate the component TO ENTER F 1 TEST CYCLE 1 Power up unit 2 Close detergent cup and latch door 3 Press KEYPAD 9 and KEYPAD 8 simultaneously for one second The control will then step through the test automatically TO EXIT F 1 TEST CYCLE 1 Press START RESET to skip each step until the end 2 The control will then exit the test cycle pump out any remaining water and return to normal operation F 1 TEST CYCLE MATRIX ACTION LED DISPLAY DESCRIPTION 1 Start SENSING and WASHING flash for 10 seconds 2 Model Number Display Combination of KEY 1 LOCK and DELAY START 1 2 or 3 Use KEY 1 MS3 and DELAY START LEDs to display model number in binary for 5 seconds 3 Illuminate Display All LED s Energize2. all LEDs for 5 seconds 4 Trip Detergent amp Fill DRYING SANITIZED Trip the detergent cup Energize he water valve for 50 seconds 5 Fill amp Circulate RINSING Energize the water valve and main pump for 10 seconds Close the active vent 6 Circulate amp Heat RINSING SANITIZED Energize the main pump and heater for 60 seconds 7 Calibration SENSING All relays and LEDs will be off while the processor calibrates he turbidity sensor 8 Circulate amp Drain RINSING DRYING Energize the main pump and auxiliary pump to evacuate water rom the unit for 10 seconds 9 Circulate RINSING DRYING SANITIZED Energize the main pump to circulate water in the unit for 50 seconds 10 Trip Rinse Agent amp Self diagnostics WASHING Trip the rinse agent Read Turbidity Sensor Read tub temperature sensor Read EEPROM If diagnostics or turbidity errors occur energize the beeper and flash LEDs see below 11 Fill WASHING SANITIZED Energize the water valve for 50 seconds 12 Fill amp Circulate WASHING DRYING Energize the water valve and main pump for 3 seconds 13 Circulate amp Heat WASHING DRYING SANITIZED Energize the main pump and heater for 60 minutes 14 Auxiliary Pump All LED s Energize all LEDs and the auxiliary pump to evacuate water for 5 seconds Open the active vent 15 Auxiliary Pump WASHING RINSING Energ
3. GE Consumer amp Industrial GE Appliances General Electric Company Louisville Kentucky 40225 Service Bulletin DISHWASHERS DD 04 04 SHORT DOOR ELECTRONIC DISHWASHERS SENSOR MODELS EDW3000G02 GSD5400G02 GSD5500G02 GD5800G02 GSD5900G02 AND LATER NON SENSOR MODELS GSD4800J01 AND LATER SEPTEMBER 2004 NEW ELECTRONIC CONTROL The short door electronic dishwashers feature a new elec tronic control that replaces the sequence switch and control on previous models with a synchronous detergent trip motor and a control with relays on the main circuit board There are two different controls one for sensor models and the other for non sensor models The control for use on sensor models is a WD21X10197 This looks similar to the control used on the Triton XL and stainless steel line of dishwashers However the controls are not interchangeable The keypad is now a separate part but functions and looks the same as the keypad on the previous integrated control There are two keypads used WD21X10198 and WD21X10199 WD21X10198 and WD21X10199 WD21X10197 The control used on the non sensor models is a WD21X10195 This control looks similar to the WD21X10100 used on the previous non sensor models _ Biononnoniely Kita b WD21X10195 The look of the escutcheon and insert is unchanged Shown below is a table of features in the new controls Characteristic Sensor Control Non Sensor Contro
4. ace the following as required 1 Jumper resistor correct and properly plugged in 2 Control Listed below are control error codes visible only during the F1 test and only on sensor models Flashing Light Explanation Possible Cause Sensing light and continuous beep Control is receiving an unexpected signal from the turbidity sensor Check and repair or replace the following as required 1 Turbidity sensor connections 2 Turbidity sensor 3 Control Heated dry light Control is reading the tub temperature sensor as open or short circuit thermistor is in the turbidity sensor Check and repair or replace the following as required 1 Turbidity sensor connections 2 Turbidity sensor 3 Control Lock light EEPROM error Check and repair or replace the following as required 1 Control 165D6290G028 MODELS WITH A TURBIDITY SENSOR A asm ey T wae 3 H NOTE INDICATES KEYPAD USED ONLY ON SOME MODELS THIS DISHWASHER IS PROGRAMMED WITH A SERVICE MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING THE DISHWASHER EACH COMPONENT MAY BE CYCLED TO DETECT IF IT IS FUNCTIONING CORRECTLY COMPO NENTS ARE CYCLED BY PRESSING KEYPADS TO THE LEFT OF THE START RESET KEYPAD USE THE MATRIX BELOW TO DETERMINE HOW TO CYCLE EACH COMPONENT TO ENTER SERVICE MODE PRESS KEYPAD 9 AND KEYPAD 3 SIMULTANEOUSLY FOR 3 SECONDS TO EXIT SERVICE MODE PRESS THE START RESET
5. below are the control error codes the customer could see or hear and possible fixes Sensor Models Flashing Light Explanation Possible Cause No light with continuous beeping sound Key pad not plugged in or model typing resistor on keypad circuit board not detected Check and repair or replace the following as required 1 Keypad plugged in 2 Keypad 3 Control Normal light with beeping sound Normal light flashes and control beeps when the detergent trip motor cannot find its home position Check and repair or replace the following as required 1 Connections to detergent trip motor 2 Operation of trip motor sensing switch 3 Operation of trip motor 4 Cam and detergent trip mechanism for free operation 5 Control Note No lights flash when cycle is cancelled and the dishwasher is resetting Non sensor models Flashing Light Explanation Possible Cause Start Reset Cycle cancelled dishwasher resetting Normal operation Normal light with beeping sound Normal light flashes when the detergent trip motor cannot find its home position Check and repair or replace the following as required 1 Connections to detergent trip motor 2 Operation of motor sensing switch 3 Operation of trip motor 4 Cam and detergent trip mechanism for free operation 5 Control Clean light with beeping sound Model typing plug not detected Check and repair or repl
6. ize the auxiliary pump to SANITIZED evacuate water from the unit for 70 seconds 16 Exit NOTE DELAY START 1 2 amp 3 represent the eftmost middle and rightmost DELAY START LEDs respectively In STEP 10 of the F1 Test Cycle If the control senses a turbidity sensor error the control will flash the SENSING LED If the control senses a tub temperature sensor error then the control will flash the HEATED DRY LED If the control senses an EEPROM error then the control will flash the LOCK LED f any of these diagnostic errors are detected the cycle will not advance to STEP 11 until a key is pressed 165D6290G029 MODELS WITHOUT A TURBIDITY SENSOR THIS DISHWASHER IS PROGRAMMED WITH A SERVICE MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING THE DISHWASHER EACH COMPONENT MAY BE CYCLED TO DETECT IF IT IS FUNCTIONING CORRECTLY COMPONENTS ARE CYCLED BY PRESSING KEYPADS TO THE LEFT OF THE START RESET KEYPAD USE THE MATRIX BELOW TO DETERMINE HOW TO CYCLE EACH COMPONENT CLEAN SENSOR SELECTIONS OPTIONS CLEAN NOTE INDICATES KEYPAD USED ONLY ON SOME MODELS WHILE THIS KEYPAD MAY i NOT BE VISIBLE THE INDICATED SPACE SHOULD ALWAYS BE USED AS A KEYPAD TO ENTER SERVICE MODE TO EXIT SERVICE MODE PRESS KEYPAD 9 AND KEYPAD 1 SIMULTANEOUSLY FOR PRESS THE START RESET KEYPAD AT ANYTIME TO EXIT 5 SECONDS Service Mode Test Matrix NOTE After 5 minutes of Description Time in Seconds Eh a AANA will automatically turn off Activate
7. l Detergent Trip Synchronous motor Synchronous motor 120 volt switching Relays Relays Model Selector Keypad Resistor jumper plug F1 Test cycle Normal amp Pots Normal amp Pots Service mode Pads 9 amp 3 Pads 9 amp 1 Trip detergent cup if Feature not available Feature not available inadvertently closed manually open cup manually open cup Please note a service mode feature is now included in the control This functions much like the Service Mode on Triton XL dishwashers Pertinent sections of the respective mini manuals are attached to this Bulletin for reference Also note that previous short door electronic models had a feature that allowed customers to open the detergent cup by pressing the start pad three times with the door unlatched This feature is not available on the new controls The Owner s Manual mentions the availability of this feature on page 14 or 13 respectively Be aware this is incorrect The Owner s Manuals have been corrected Early production sensor models do not flash the washing light or any other light on reset The Owner s Manual says the washing light should flash on reset The programming in the control will be modified to include this feature beginning with September 2004 production A reset on non sensor models will cause the Start Reset light to flash for 90 seconds GE CONFIDENTIAL AND PROPRIETARY INFORMATION NOT FOR PUBLIC DISCLOSURE ND 9210404 Listed
8. s Main Pump Activates Auxiliary Pump NOTE When a component 5 is activated in the SERVICE Activates Drain Solenoid MODE the output will Activates Detergent Module continue to remain active ON until the Maximum time has expired or another 6 Activates Heating Element keypad is pressed START RESET Used to EXIT Service Mode Activates Water Valve N D 921 04
Download Pdf Manuals
Related Search