GE 24962 User's Manual
Contents
1. press and release SHIFT then LEFT Vol RIGHT press and release SHIFT then RIGHT Vol OK press and release SHIFT then OK Mute EXIT press and release SHIFT then EXIT Prev Ch The red indicator blinks for each key press Direct Code Entry 1 Enter the 4 digit code 1 2 2 from the code tables Press and hold the SETUP button until eta the red indicator stays on then release setup the SETUP button Press and release the desired mode button TV DVD etc The red indicator blinks then stays lit on separate sheet Note after a valid code 4 5 6 entry the red indicator turns off For an invalid 4 code the red indicator 7 8 9 flashes With your device on press ON OFF If the device turns off no further programming is required 9 Note If some buttons do not operate your equipment try one of the other codes for your brand Write your codes down here for easy reference later SAT CBL Code Search If your device does not respond after you have tried all the codes for your brand or if your brand is not listed try searching for your code by following these steps 1 Manually turn on the device TV DVD etc to be controlled 2 Press and hold the SETUP button until the red indicator stays on then release the SETUP button 3 Press and quickly release the desired mode button TV DVD etc The red indicator bl2. from your original remote may not be controlled by this remote Use the Original remote if available to control such functions Sometimes buttons other than described in these instructions may actually perform the function For example the CHAN and VOL buttons might be used to navigate through menu choices We recommend you experiment with the remote to identify if such situations pertain to your equipment The 24962 is easy to use easy to program and it gives you total control at the touch of your fingertips Battery Installation 1 On the back of the remote push down on the tab and lift the cover off 2 Match the batteries to the and marks inside the battery case then insert 2 AAA Alkaline batteries 3 Press the battery cover back into place Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds This will save your batteries should your remote get stuck in a place where the buttons remain depressed e g between the sofa cushions Code Saver You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed However do not press any buttons until batteries are installed in the remote If buttons are pressed without batteries in the remote all codes will be lost ema Code Setup 3 The SETUP button is used to setup the remote You can either setup the remote using the code for your brand of product from the c
3. 24962 Universal Remote Instruction Manual e e O 6 6 e 0 00 2000006 0 0 Po099000 Table of Contents SAN e RIDER E REZ MAR PI Re AE RIN CR r A aaa 3 Battery Installation mc eee 3 Battery SEVEN crize cate se xuyan da leet dena eke 3 Code Savel iyi lle d nak nO ayak aia GULER Ay 3 Code Setup i eee eee eee en eee 3 Button FUNCIONS ss lt ssccscscccure cola ne eu a 4 SIME zii tuica lege atoli late ti a DOI i ie aa 6 Direct Code Entry nea aa ss ache cle aaa i mea sa e ba 7 Cod Sea G N ella niya nasik a co il oa Dl ora a 8 Code ldentification E EEEEEEE 9 Using Your Remote eee eee eee 10 Controlling Devices with Separate Power On and Off eee eee 10 Controlling Combo Devices 10 DVR DVD Punch Through 10 Volume Mute Control and Punch Through 11 Setting All Volume Mute Control to any one Mode eee eee 11 Setting any Mode for its own Volume Mute Contro 12 Troubleshooting eee eee eee eee 13 Congratulations on your purchase of the 24962 Universal Remote Control The 24962 is one of the most easy to use remote controls available today With the 24962 juggling multiple remote controls is a thing of the past Your 24962 controls up to three devices including the most popular brands of TV DVD Satellite Cable etc Note Some functions
4. D PLAY STOP REW FF PAUSE oper ate your DVD or DVR even when the remote is set to operate the TV record stop pause Also operates DVD DVR Scan El e lt e o 0 9 e 6 E Button Functions cont Red Indicator ON OFF Turns Lights when any device On or Off button is pressed INPUT For some TVs press repeatedly to select from available viewing sources antenna cable box DVD etc CHANNEL Up Down Changes the channels VOLUME UP DOWN Changes the volume level of the product normally the TV V EU PREV CH Returns to the previously selected channel EXIT Exit On Screen Menus and or Return to previous On Screen selection 6 93 NUMBERS Enter numbers for direct channel selection Some products require ENTER to be pressed after channel selection oh oR 1 2 6s 8 00 6 vEt record stop pause ENTER For some TV models used after direct channel number entry to immediately change to the selected channel 80 Note The REC button must be pressed TWICE to record from your DVR For some brands of DVRs you might need to press the REC button once then press it again for three seconds SHIFT Function Press SHIFT Setup prior to the shifted key func tion e g for MENU press and release SHIFT Setup then MENU Info UP press and release SHIFT then UP Chan DOWN press and release SHIFT then DOWN Chan LEFT
5. follow the six steps below 1 Press and hold the SETUP button until the red indicator stays on Release the SETUP button Qe 2 Press and release the desired mode button TV DVD etc The red indicator blinks then stays lit 3 Press and release the SETUP button The red indicator blinks once and remains lit 4 To find the first digit for 1 2 the code stored under __ TO te the mode key pressed Peran YERE a ik in step 2 press each 4 5 6 numeric key from 0 9 in rs turn The number that a ea az causes the indicator 8 9 light to blink is the first digit in your code 0 5 To find the second digit repeat step 4 Ea setup 6 Repeat step 4 again to find the third and fourth digits This time the red indicator turns off and stays off Using Your Remote Controlling Devices with Separate Power On and Off Buttons Some GE RCA and ProScan models require you to press the device button for more than one second to turn the device on and the POWER button to turn the device off Controlling Combo Devices Some Combo devices e g TV DVR TV DVD DVD DVR etc will require you to set up two different Mode buttons to control both parts of the Combo device For example if you have a TV DVD Combo you might need to set up one code under the TV button to control the TV part AND a separate code under any other Mode button to control the DVD part DVR DVD Punch Through T
6. his remote allows the 6 DVD VCR transport buttons i e PLAY PAUSE STOP FF REWIND and REC to Punch through from any Mode programmed with TV SAT or Cable codes to the last DVD or VCR programmed Mode you used i e the transport keys control your DVD or VCR player even when you are in TV SAT or Cable mode If you use a SAT DVR Cable DVR etc you may want to disable this Punch through feature to allow the transport keys to control your DVR device The following steps will disable the punch through feature 1 Press and hold SETUP until the red indicator stays on then release the SETUP button 2 Press and hold PAUSE until the red indicator turns off then release the PAUSE button The PAUSE button needs to be held held for about 3 seconds before the red indicator turns off The punch through feature can be enabled again by repeating the above steps 10 Using Your Remote cont Volume Mute Control and Punch Through This remote lets you select which device Mode controls your Volume Mute buttons The remote is initially set for all device Modes to use their own Volume Mute control if present If the programmed code has no Volume Mute operation of its own then those buttons will punch through control to the TV Mode device without needing to change to TV Mode Setting ALL Volume Mute Control to any one Mode This routine can set all Modes to punch through to any one chosen Mode for Volume Mute button control w
7. inks off once 4 Press the CHAN button __ repeatedly up to 300 times chana gt until the device to be controlled i changes channel The red indicator blinks off with each button press If you accidentally overshoot the code required press the CHAN button to backtrack through the library until the device changes channel Pressing CHAN changes direction to forward again 5 Press and release ENTER to install the code Most users will store DVD codes under the DVD button and Satellite or Cable codes under SAT CBL If for ex ample you want to store a DVR code under SAT CBL first follow the procedure for Direct Code Entry page 8 and press SAT CBL in step 2 of Direct Code Entry then enter ANY DVR code in step 3 of Direct Code Entry Then follow the steps above for Code Search Note If the device does not have a CHAN button use PLAY DVD DVR VCR only or POWER instead Code Search starts from the currently stored 4 digit number under that mode Sometimes the first code that works with your device may only allow limited functionality e g the MENU button might not work There may be a code that performs more functions Continue the code search process until the best code is found 8 Code Identification The Code Identification Feature allows you to identify the 4 digit library code stored under your device key For example if you want to find out what 4 digit code is stored under your TV device key
8. ithout the needing to change to that Mode 1 Press and hold the SETUP button until ema the red indicator turns on then release setup the button m 2 Press and hold the MUTE button until the red indicator blinks off then release the button 3 Press and release the desired Mode button TV DVD etc for Volume Mute control the red indicator blinks then stays on 4 Press and release the MUTE button and the red indicator turns off The red indicator will blink rapidly for three seconds if the Mode you have selected has no Volume Mute control e All other Modes will now punch through to your chosen Mode for Volume Mute control 11 Using Your Remote cont Setting any Mode to use its own Volume Mute Control This routine can set any Mode to use only its own Volume Mute control Note If your chosen Mode has no Volume Mute functions of its own then the Volume Mute buttons will do nothing 1 Press and hold the SETUP button until the red indicator turns on then release the button setup 2 Press and hold the MUTE button until ink the red indicator blinks off then release the button 3 Press and release the desired Mode button TV DVD etc the red indicator blinks then stays on 4 Press and release the VOL button the red indicator blinks then stays on 5 Press and release the MUTE button and amp the red indicator turns off Your chosen Mode will now use its own Volume Mu
9. ncidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 10 E Memorial Road Oklahoma City OK 73114 2205 24962 Universal Remote Instruction Manual Jasco Products Company 10 E Memorial Road Oklahoma City OK 73114 2205 Made in China 24962 03 10
10. ode tables on separate sheet or you can search through the library of codes until you find a code that works for your product Please refer to Code Search page 8 for more information on using the code search feature to learn how to search through the library of codes for your products NOTE You can store any kind of code under any mode except TV l e you can store a DVR code under the SAT CBL button or a cable code under the DVD button etc However you can only store TV codes under the TV button Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling E g PREV CH may be called RECALL or ENTER may be called DISPLAY These differences depend on the brand and model of your product Also this remote can only operate features that exist on your product E g your product must have PREV CH ability for the PREV CH button to operate this feature TV DVD SAT CBL Selects product to be operated SETUP For setup SHIFT Accesses shifted functions MUTE Turns off the TV sound while the picture remains OK Selects menu items for the device you are controlling INFO button brings up DVD Display or Control Menu for Chapter Track Title number Time remaining elapsed indication system information etc MENU Selects the on screen menu D000 DOT Used to select digital chan nels e g 2 3 okoko RECOR
11. te control Troubleshooting Remote does not operate your product e Press the mode button of the product you want to control Program the remote with a new code e Install new batteries You might have to reprogram your remote after installing new batteries e Remote may not be compatible with your product Remote does not operate some features of your product e Sometimes a particular code might operate some features but not all Try programing remote with a new code e Remote may not be able to operate all features of your product or button names might be different than your product Red Indicator blinks after you program a product code Remote did not accept the code e Try to program the code again or try a different code Lost Your Codes Enclosed with this remote is a sticker on which you should write the codes for each device you programmed Apply the sticker to the back of the remote or somewhere convenient for future reference Also on the sticker is our website address which should you lose your codes or programming instructions you can find available on our website www jascoproducts com 13 90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to consequential or i
Download Pdf Manuals
Related Search