Garmin RF Remote User's Manual
Contents
1. 2007 Garmin Ltd or its subsidiaries All rights reserved Except as expressly provided herein no part of this manual may be reproduced copied transmitted disseminated downloaded or stored in any storage medium for any purpose without the express prior written consent of Garmin Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited Information in this document is subject to change without notice Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements Visit the Garmin Web site www garmin com for current updates and supplemental information concerning the use and operation of this and other Garmin products Garmin is a trademark of Garmin Ltd or its subsidiaries registered in the USA and other countries GPSMAP is a trademark of Garmin Ltd or its subsidiaries This trademark may not be used without the express permission of Garmin Refer to your chartplotter owner s manual or product information sheet to view the warranty warn2. until New Wireless Remote Found appears on the chartplotter ti Message New Wireless Remote Found 2 Select Connect on your chartplotter To select a chartplotter press and release the Pairing Button that is paired with the chartplotter you want to control Specifications e Size 135 mm H x 50 mm W x 25 7 mm D 5 3 x 2 x 1 e Weight 71 g 2 7 oz without battery 101 g 3 6 oz with batteries e Case waterproof to IEC 529 IPX 7 2 46 GHz 10 m 32 ft this value may vary slightly depending on the installation of the chartplotter e Frequency e Max Range e Battery Life 100 days when used 15 minutes per day 3 years shelf life e Operating Temperature Range 15 C to 70 C 5 F to 158 F 40 C to 85 C 40 F to 185 F e Storage Temperature Range
3. a different circuit from the GPS unit e Consult the dealer or an experienced radio TV technician for help This product does not contain any user serviceable parts Repairs should only be made by an authorized Garmin service center Unauthorized repairs or modifications could result in permanent damage to the equipment and void your warranty and your authority to operate this device under Part 15 regulations Garmin International Inc 1200 East 151st Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire S040 9RB UK Garmin Corporation No 68 Jangshu 2nd Road Shijr Taipei County Taiwan www garmin com July 2007 Part Number 190 00856 10 Rev A Printed in Taiwan RF Remote owner s manual For Use with GPSMAP 4000 5000 Series Chartplotters GARMIN Introduction The 4000 5000 Series RF Remote is for use with the following Garmin chartplotters e GPSMAP 4008 GPSMAP 5008 e GPSMAP 4012 GPSMAP 5012 e GPSMAP 4208 GPSMAP 5208 e GPSMAP 4212 GPSMAP 5212 The remote is used to control the 4000 5000 screens It can be used up to 10 meters 32 feet from the chartplotter and does not need to be pointed directly at your chartplotter The remote operates on two AAA batteries not included To replace the batteries use a small Phillips screwdriver to open the access cover on the rear panel Use alkaline batteries for best results Ensure your chartplotter has the c
4. ings cautions and the software license agreement Visit the Garmin Web site www garmin com for current updates and supplemental information concerning the use and operation of this and other Garmin products FCC Compliance This product has been tested and found to comply with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE These limits are designed to provide more reasonable protection against harmful interference in a residential installation and are more stringent than outdoor requirements Operation of this device is subject to the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment generates uses and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet that is on
5. urrent software available at www garmin com Pairing 7 buttons Description of Buttons Pairing buttons press and hold to pair a remote with a chartplotter Press and release to select a paired chartplotter panget Rocker press up down left and right to move the map pointer and enter data Rocker SELECT press to confirm messages and select Up Down items MENU press to view additional options on SELECT most screens MARK MARK SELECT LOCK press to lock all remote functions HOME HOME MENU MENU Press again to unlock The remote beeps when it is locked and a button is pressed MOB Man OverBoard MOB Man Overboard press to mark your current location as a Man Overboard point LOCK HOME press at any time to return to the Home screen MARK press to mark your current location as a waypoint Up Down ress to highlight menu items Range press up and down to increase and decrease the map zoom scale Getting Started Use one of the three pairing buttons to pair your remote with a specific chartplotter If you have more than one chartplotter this allows you to separately control up to three chartplotters To allow wireless connections on your chartplotter 1 From the Home screen select Configure gt Communications gt Wireless Devices 2 Set Allow New Connections to Yes To pair the remote with a chartplotter 1 Press and hold one of the Pairing Buttons
Download Pdf Manuals
Related Search