Fusion MS-AB206 User's Manual
Contents
1. 1 x MS AB206 Active Subwoofer 1 x Power GND Remote ON wiring loom 1 x 6M RCA Cable 4 x Stainless Steel Mounting Screws 1 x Control Panel Cover 2 x Control Panel Cover Screws Manual Warranty Card SPECIFICATIONS Peak Power Speaker Output Rated Power Speaker Frequency Response Subwoofer Frequency Response Low Pass Filter variable Low Pass Filter off Enclosure Type Woofer Size Fuse DIMENSIONS 350 Watts Total 210 watts Subwoofer 140 watt Speaker Output 26 Watts RMS x 2 at 4 Ohms per channel 43 Watts RMS x 2 at 2 Ohms per channel Connect two 4 ohm speakers in parallel per channel to achieve this output 20Hz 20kHz 25Hz 200Hz 25Hz 200Hz Fixed for use with FUSION MS BX3020 Passive Radiator 6 Down Firing 6 Passive radiator 15 amp Length 500mm 19 11 16 Width 250mm 9 27 32 Height 163mm 6 13 32 CONTROL DESCRIPTIONS Sub Level This allows the Subwoofer level to be adjusted to the desired balance with the speakers Low Pass Filter LPF The MS AB206 has both a fixed and variable low pass filter When pairing the MS AB206 with the FUSION MS BX3020 speakers switch Low Pass filter to off When connecting other FUSION speakers switch the Low Pass filter to on and adjust the frequency 25Hz 200Hz Auto On For use when a remote on wire is unavailable Use this switch to utilize the Auto On feature of the MS AB206 When an Audio S2. ASSURANCE True Marine products are designed and engineered at FUSION s industrial design headquarters in Auckland New Zealand specifically for the marine environment This True Marine product has been engineered to produce outstanding bass designed for dry area installation Any product that bears the True Marine seal of assurance has been designed for simplicity of use combining the most advanced marine technologies to produce and an unrivalled entertainment experience All True Marine products are supported by FUSION s 3 Year Limited Consumer Warranty NOTES PUBLISHED BY FUSION ELECTRONICS LIMITED Copyright 2013 by FUSION Electronics Limited All rights reserved Specifications and design are subject to change without notice V1 0 YOU CAN HELP PROTECT THE ENVIRONMENT Please remember to respect the local regulations Hand in the non working electrical equipment to an appropriate waste disposal centre FUSION Electronics New Zealand 09 369 2900 FUSION Electronics Australia 1300 736 012 FUSION Electronics Europe 31 76 5723 632 FUSION Electronics USA 623 580 9000 FUSION Electronics Pacific 64 9 369 2900 WWVWV FUSIONELECTRONICS COM ruston
3. Dr 2 USER INSTALLATION MANUAL rUuSsiOn MS AB206 ACTIVE SUBWOOFER WITH 2 CHANNEL CLASS D SPEAKER AMPLIFIER a VVWW FUSIONELECTRONICS COM FOR THOSE WHO ENJOY THE FINER THINGS IN LIFE Introducing high end audio for the marine cabin environment designed for exceptional sound in any vessel This now represents the highest quality purpose built marine audio equipment from FUSION With unrivalled bass reproduction the MS AB206 creates the perfect atmosphere for entertaining or relaxing Engineered at FUSION s industrial design headquarters in Auckland New Zealand Specifically tuned to produce the best acoustic result when installed in a saloon or cabin environment When paired with the MS BX3020 cabin speakers the sound is remarkable and like nothing you ve heard before FAMILY FRIENDS FUSION It s what boating is all about REGISTER OGE PRODUCT ONLINE For your own peace of mind register your product purchase online at www fusionelectronics com We ll keep you up to date with any news related to your product or new accessories to help you get the most from your product All FUSION True Marine Products are backed by a 3 Year Limited Consumer Warranty and by registering your product you can be assured that if the unexpected occurs we ll have your details and be ready to help RECORD YOUR PRODUCT DETAILS HERE SERIAL NUMBER DATE OF PURCHASE AFFIX RECEIPT HERE CONTENTS OF THE BOX
4. cable red to the positive of the vessel s 12V power system A fuse or circuit breaker must be used in the positive cable close to its connection to the vessel s 12V system Use either the supplied inline fuse or a panel mounted fuse circuit breaker of the same rating If the supplied cables are not long enough extend them with cable of the same gauge For very long cable runs consult a qualified marine electronics installer Connect the Remote ON wire blue to the remote turn on wire or power antenna wire of the head unit If neither of these is available then select the Auto On feature of the MS AB206 Connect the RCA cables to the source unit s full frequency range Pre Out terminals ensure RCA cables are run avoiding power and ground cables also avoid other electric motors etc that could introduce unwanted noise Connect the marine cabin speakers to the speaker outputs Make sure to observe polarity Check all connections Finally connect the plug end of the power negative remote harness to the MS AB206 WHEN CONNECTED TO MS BX3020 SPEAKERS SET LPF TO OFF POSTION SUB AUTO LEVEL LPF LPF ON POWER JOOJ L MIN MAX 25Hz 200Hz T ON ON OFF AL OFF lt RCA Input lt hH Positive 12V Cable Red 480mm 18 29 32 THIS IS TRUE MARINE FUSION S STAMP OF QUALITY AND
5. ignal is present the unit will switch itself on and with no signal it will power off after a period of 90 seconds INSTALLATION Make sure the Marine Active Subwoofer is firmly secured Check before drilling or cutting holes DO NOT work near fuel tanks fuel lines hydraulic lines or electrical wiring DO NOT mount the Marine Active Subwoofer in such a way as to pinch or damage the wires Make sure everything is firmly connected before attaching the 12V wire Make sure the 12V wire is fused as close as possible to the battery ALWAYS use a fuse with the recommended rating FUSION MS AB206 is specifically designed for optimal performance when placed in a two plane wall plus floor or a three plane two walls plus floor situation Placement in a wall or a storage locker behind a protective grille is also possible 50mm 1 31 32 WALL WALL LE ses Left and Right Channel Remote ON wire Blue Positive and Negative Speaker terminals Negative 12V Cable Black Be sure to use the supplied wiring loom Run the positive and negative cables together Connect to the vessel s 12V power system at a point such as a distribution panel where the positive and negative terminals or bus bars are positioned near to each other Connect the negative cable black to the negative of the vessel s 12V power system ensure this is the first cable to be connected Connect the positive
Download Pdf Manuals
Related Search