Fusion EMPEROR L702B User's Manual
Contents
1. Battery Type Number of Cells in series Battery Capacity Memory Number 2911 LiPo 3S 2200mAh gt CHG 2 1A 4 20V C Line selection DCHG 10 0A 3 0V C arrow STORE MODE START gt O NiMH CHG 3 3A DCHG 5 0A 9 01 E Or D To edit the battery parameters make sure the selection arrow is on the top line and press the Enter button to highlight the memory number Using the Inc or Dec buttons the selected memory 0 19 can be changed By default each memory is populated with a sample configuration but these can be adjusted to suit your requirements Pressing the Enter button again selects the Battery Type for the selected memory The battery type can be changed using the Inc and Dec buttons The available battery types are NiCd Nickel Cadnium 1 2V cell NiMH Nickel Metal Hydride 1 2V cell LiPo Lithium Polymer 3 7V cell Lilo Lithium lon 3 6V cell LiFe Lithium Ferrite 3 3V Cell Pb Lead Acid 2V cell Pressing the Enter button again highlights the number of cells in series which can be adjusted using the Inc and Dec buttons If you are unsure of the number of cells in your battery pack then this can be calculated by dividing the total battery voltage by the individual cell voltage Pressing the Enter button again selects the battery capacity setting then back to the line se2. Cut off when x of capacity is reached Do not detect peaks for x mins PEAK DELAY TRI CURRENT Trickle Charge Rate SAFETY TIMER 120min Cut off if maximum time is reached CHG CHARGE This line shows the charge current and the delta peak cut off voltage These values can be edited by pressing the Enter button to highlight the parameter then the Inc and Dec buttons to edit the value When charging NiCd and NiMH batteries most chargers detect when the pack is fully charged by using a method called delta peak This monitors the voltage of the pack which increases as the pack becomes charged When the pack is fully charged the pack starts to get warm and the voltage then starts to drop The delta peak cut off voltage is the voltage drop per cell that is detected before the charger will stop the charge The default delta peak voltage setting for NiMH packs is 5mV cell and for NiCd is 8mV cell To start the charge function press the Enter button for 2 seconds with this line selected The screen will then move to the charge type screen see page 12 n b The selected charge currents will not be used if Automatic charge type is selected DCHG DISCHARGE The discharge line shows the discharge current and the discharge cut off voltage per cell The default cut off voltage for NiCd NiMH cells is 0 8V cell Pressing the Enter butt
3. Thank you for purchasing this Fusion Emperor L702B Pro charger We are sure you will be pleased with its performance and features In order to ensure that you obtain the maximum benefit from its operation please read the instructions carefully OPERATING INSTRUCTIONS Please keep for Future Reference CONTENTS Sp cifications e eden 2 Gerieral Operatioli iuuenes eerte tio otiosi rh pna s tue tesa Fo Fo cu ku rana kde dd re n enda Euh 3 Output Battery Connections ee eeeeeseeeeeeeeeseeeseneeeeeeeeeeseuaaaeeeeseseneneaaeeeeeenenenes 3 Turning On amp Setting the Input Power eesseeseeeeeeneenenneeen nennen 4 MAE DISHIAY Sranane ina raa aa ER PETS 4 Msi d greci isernia eiaeia tan a eai a NE REEE A A E S 5 Battery Memory Sereen Em 6 Lithium Functions and Parameters sesessessssseessersrrserrerersrensrersrerereseresereseesrensrensrenee 7 NiCd NiMH Functions and ParameterS ccccccsssccssccessscessecesssccssecessteessecessteesseeesaees 9 CMAN EIB enei a e I0 2020 E AAE E A aaa e EEGA 11 Charging a Eithi miPack ii eret eitis ehe etr ena ri e rt rane re ee 11 Charging a NiCd NiMH Pack cccecceceecceseeseeseeeceeceeceeeeeeeseeaecaesaecaeseeeeeseaeeaeeateaeeas 12 Other Sarees ec 13 User Settings SCreeni cuiii hse easscedenaedeceasuziidesaacdenvvancedes unt ENEDES renr DENNA 13 Data View EUIS ESEE n SiE 13
4. The safety timer can be used to terminate a charge if it is not completed within the selected time period CHARGE RATE MAXIMUM CHARGE RATE The charge rate allows you to set the maximum charge rate for the pack being charged The default is 2C but some newer packs can allow up to 5C 5 x capacity so increasing this value allows the user to select a higher charge current in the charge parameters TCS CAPACITY TCS Terminal Capacity Selection allows the user to select a capacity at which the charger will beep or stop charging Lithium batteries are charged using a constant current then constant voltage CC CV so when the cells reach their maximum voltage the charge current is slowly reduced until the charge is complete Because the charge current is being reduced the last 10 30 of the charge takes proportionally longer than the first part Therefore the TCS capacity can be set to warn the user when the selected capacity is reached which can be useful if the user does not require a full charge in the battery so it can be used sooner TCS END ACT TCS END ACTION When the selected TCS capacity is reached the charger can be set to continue the charge and warn the user that the TCS capacity has been reached or the charger can stop the charge NICD NIMH FUNCTIONS AND PARAMETERS Charge NiMH 6S 3000mAh 1 3 0A 8mv C 3 0A 0 8V C Discharge CD T TEMPER Cut off Temperature Cycle
5. E EA E A A 13 Balancer ViW T caves 14 Sy Eur E 14 Factory Setting E Shute 14 digo au CC c 15 Safety Preca tiOns sre HEROS HERO ERREUR RE Een Ede up eed 15 Lithium lon Polymer Battery Safety Warnings essere 16 SPECIFICATIONS MODE TYPE SPEC Power Supply DC Input 11 28V DC Battery Types NiCd NiMH LiPo Lilon LiFe Pb Operating Modes NiCd NiMH Charge Discharge Cycle LiPo Lilon LiFe Pb Charge Discharge Store Operation function Charge NiCd NiMH Automatic charge Normal charge Linear charge RE FLEX charge Charge LiPo Lilon LiFe Pb CC CV charge Discharge Automatic discharge NiCd NiMH Normal discharge NiCd NiMH Linear discharge Store Mode 60 Capacity Number of Cells NiCd NiMH 1 18 Cell LiPo Lilon LiFe 1 7 Cell Pb 1 12 Cell Charge Current NiCd NiMH 0 1A 20 0A max 300W LiPo Lilon LiFe 0 1A 20 0A max 300W Discharge Current NiCd NiMH LiPo Lilon LiFe Pb 0 1A 10 0A max 50W Discharge Voltage NiCd NiMH 0 1 1 1V cell LiPo Lilon LiFe 2 5 3 7V cell Trickle Current NiCd NiMH Off 500mA Auto Mode Charge Current 20 Cycle Mode Cycle time 1 10 Cycles NiCd NiMH only Cycle delay 1 30 min Cycle
6. appears to be brand new Before commencing charging ALWAYS double check the settings on the charger to ensure it is set correctly for the battery pack to be charged Using the wrong settings is likely to result in damage to the battery pack being charged and could result in the battery catching fire 17 wouw LosicRC com Logic RC Limited 14 Hartham Lane Hertford SG14 1QN United Kingdom rev 11 2009
7. below 3 volts per cell will invalidate all warranty claims NEVER charge Lithium Polymer battery packs at greater than 4 2V per cell Lithium lon at 4 1V volts per cell or LiFe at greater than 3 7V per cell as this will cause irreversible damage to the cells and will invalidate all warranty claims NEVER charge Lithium battery packs above their maximum charge rate This can damage the pack and can be dangerous Generally Lithium Polymer packs should not be charged above 2C 2 x Capacity However some newer packs do allow charging at up to 5C but charging at these higher rates will reduce the life of the pack e g Pack of 2500mAh capacity 2C 5000mAh 5A max charge current DO NOT use discharge rates in excess of those specified with the battery pack as this will result in a significant drop in voltage under load and will dramatically reduce the number of charge discharge cycles the battery pack will give If disposing of Lithium battery packs ensure that the pack is fully discharged by using a light bulb electric motor or similar to completely discharge the pack DO NOT allow any Lithium battery pack to short circuit as this is likely to result in a minor explosion and consequent fire BEFORE charging any Lithium battery packs they should be closely inspected for any damage such as punctures in the sleeving or if the battery has swollen or expanded in size If any such damage is detected DO NOT charge even if the battery otherwise
8. stop the charge After selecting charge for a NiCd or NiMH pack you are given the option to select four different charge types These are Automatic This is a fully automatic charge that will ignore the selected charge parameters The charger will monitor the battery by stopping the charge for a few seconds every minute and then automatically adjust the charge current to make sure the best charge current is delivered to your pack Normal The charger will charge the pack at the selected charge current but will stop charging for five seconds every minute This allows for better peak detection Linear The selected current is maintained throughout the charge Re Flex Reflex sometimes know as Burp or reverse pulse charging is where the charger applies a reverse charge of 4 times the charge current for 4 1000 of every second Reflex charging is believed to help remove oxidizing gas bubbles from the cell plates in the battery allowing it to charge more efficiently Reflex charging is not always recommended for NiMH cells so please check with your battery manufacturer first 12 In this example a Normal charge is selected and then the Enter button is pressed for 2 seconds to start the charge As shown in the flow chart pressing the Mode or Esc buttons at any stage moves through the different screens giving detailed information about the charge Pressing the Es
9. 4 20V C 10 0A 3 0V C 3300mAh 5mV C 0 8V C 1X 10m 3 3A 5 0A C2D Pressing the Channel button at any time selects the other channel charger MENU STRUCTURE The menu system in the Emperor L702B is summarized in the flow chart below To move around the screens press the buttons as shown on the flow chart Where a line selection arrow is shown on the left of a line the Inc and Dec buttons can be used to move the selection arrow up or down Pressing the Enter button highlights each value on a line so that it can be changed Pressing the Esc button whilst a value is highlighted exits the editing and moves back to the line selection again Power Press and hold On the Mode button N whilst connecting the power Power hijklmnopgr yz 01234567 INPUT POWER SETTING Memory Screen User Settings Data View Cycle View Balancer View Press the Inc or Dec button to change the Press the Inc or Dec button cell number to view the charge discharge statistics for previous cycles gt OJNiMH 6S CHG 3 34 5 0A CaD BATTERY MEMORY SCREEN The battery memory screen is the main functional screen for this charger It is used to store specific battery charge discharge and safety parameters as well as being used to initiate charging discharging cycling store mode functions
10. adequately supervised by a responsible person to ensure that they can use it safely Young children should be supervised to ensure that they do not play with the charger DO NOT attempt to charge non rechargeable batteries 15 Lead Acid batteries must be placed in a well ventilated area when charging DO NOT attempt to charge whilst the input 12 volt battery is being charged as the voltage supplied to the charger may be too high LITHIUM ON POLYMER BATTERY SAFETY WARNINGS Ensure that the charger and battery are placed on a non flammable surface whilst charging NEVER charge a Lithium ION Polymer Fe battery inside a vehicle whatever the circumstances ALWAYS ensure that the charger is correctly set for the battery being charged checking both voltage and capacity Be particularly careful if using a series parallel battery pack or if using packs of different specifications with the same charger NEVER charge at a rate higher than that recommended by the cell manufacturer this can be very dangerous DO NOT leave Lithium ION Polymer Fe batteries unattended whilst they are charging Monitoring the batteries during charging is very important ALWAYS monitor the temperature of the battery being charged every few minutes If the battery becomes hot to the touch disconnect it from the charger immediately and allow to cool DO NOT recommence charging until the battery and charger have been checked for compatibility and th
11. c button for 2 seconds at any stage will stop the charge OTHER SCREENS As shown in the flowchart below the other screens are accessed using the Mode and Esc buttons Memory Screen User Settings Data View Cycle View Balancer View CAPACITY VOLTAGE 35 11 845V fMs 3 944V Omat 0 000V y 3 95V Ld OmAh I H3 94v Ca USER SETTINGS SCREEN This screen is used to set the temerature mode and gt TEMP MODE BUTTON SOUND charger sounds for each charger channel We PINISH SOUND recommend selecting a different melody for each channel charger so you can easily identify which channel has completed it s operation DCHG CYCLE DATA VIEW SCREEN The data view screen shows both the input and output gt INPUT VOLT 13 200V OUTPUT VOLT 11 123V voltages together with the current and peak a ee E E temperature readings for each channel PEAK TEMP CYCLE VIEW The cycle view screen shows the charge and discharge IE CAPACITY VOLTAGE data for the most recent pack to be charged or Es Pn B discharged 6S 3300mAh 3 3 3A 5mV C 13 5 0A 0 8V C CYCLE CsD 1X 10 If the cycle function has been used NiCd NiMH only then pressing the Inc button shows the charge and discharge statistics for the previous 10 cycles BALANCER VIEW When a Lithium pack is connected to the charger the balancer screen shows the balance statistics for the pack and allows the user to read off the individual
12. cell voltages Press the Inc or Dec Number of cells and button to select a total pack voltage specific cell to view 3S 11 845V Voltage difference between the highest and lowest cells Highest and lowest __ voltage cells SYSTEM MENU The system menu is accessed by holding down the Mode button and connecting the power In this menu you can adjust the LCD parameters and set the user name that appears on the welcome screen Press and hold the Mode button whilst connecting the power 2LCD CONTRAST 10 LCD BACKLIT ON Power lt www LogicRC com gt FUSION On ABCDEFGHIJKLMNOPQ o gt RSTUVWXYZ abcdefg hijklmnopqrstuvwx Emperor L702BP v1 yz 0123456789 www LogicRC com To edit the username press the Dec button to move down the line selection arrow to the username line When on this line selection changes to character selection so using the Inc and Dec buttons select the character to be changed and then press the Enter button to highlight the character Using the Inc and Dec buttons to select the new character and press the Enter button when finished Continue this to change each character When you have finished press the Esc key to exit this menu FACTORY SETTINGS To reset the charger to the original factory settings press and hold the Esc button when connecting the power 14 ERROR MESSAGES T
13. direction C gt D D gt C Peak sensitivity NiCd 5 25mV cell NiMH 0 3 15mV cell Temperature Sensor Centigrade 10 60 C Fahrenheit 50 150 F Max charge capacity NiCd NiMH 10 150 safety timer LiPo Lilon LiFe 10 120 Start peak delay timer NiCd NiMH 1 20 min Memory Memory number 20 Memories per channel Safety timer NiCd NiMH LiPo Lilon LiFe Pb 20 300mins amp Off Charge rate limit LiPo Lilon LiFe 1 5C TCS Capacity LiPo Lilon LiFe 10 100 TCS END action LiPo Lilon LiFe Continue Stop GENERAL OPERATION OUTPUT BATTERY CONNECTIONS The Emperor L702B Pro has two sets of outputs on the front of the charger channel 1 is on the left and channel 2 on the right Each channel has two 4mm banana sockets a 7 cell balance port and a temperature sensor input You will need an appropriate charge lead to suit the specific connector on your battery Connect this charge lead to the 4mm output sockets on the charger channel you want to use with the positive lead connected to the red socket and the negative lead to the black socket Only connect the battery to the charge lead AFTER the charge lead has been connected to the charger as the connectors on the charge lead could touch together and cause the battery to short circuit When charging a Lithium pack make sure that the balance lead is connected to the charger The charger has a JST EH type balance por
14. e Rate setting If you want to increase the charge current above 2C you must first increase the maximum charge rate before you can increase the charge current Normally the maximum cell voltage should be left at the default value LiPo 4 2V Lilo 4 1V amp LiFe 3 7V but in very cold weather a Lithium Polymer pack can be overcharged at 4 2V so reducing the maximum charge voltage to 4 1V can increase the life of your pack Press the Enter button for 2 seconds on this line to start the charge DCHG DISCHARGE This shows the discharge current and the cut off voltage per cell Pressing the Enter button for 2 seconds with this line selected will start the discharge STORE MODE START It is recommended that Lithium batteries are not left in a fully charged or discharged state for long periods of time especially when stored in a cold environment Therefore store mode will charge or discharge your pack to around a 60 charged state to help extend the life of your packs CUT TEMPER CUT OFF TEMPERATURE When used with the optional temperature sensor a safety cut off temperature can be set so that charging or discharging is terminated automatically if the temperature sensor detects the battery temperature rising above the selected value MAX CAPACITY MAXIMUM CAPACITY The maximum capacity setting is used to terminate a charge if the charger exceeds the selected percentage of the battery capacity SAFETY TIMER
15. e charger settings have been confirmed as being correct In the unlikely event of the Lithium ION Polymer Fe battery catching fire DO NOT use water to attempt to put the fire out instead use sand or a fire extinguisher designed for electrical fires When used correctly Lithium ION Polymer Fe battery packs are as safe as any other type of rechargeable battery pack However they do require different charge regimes to the longer established Nickel Cadmium and Nickel Metal Hydride technologies and have the potential of catching fire if severely mistreated If Lithium Polymer battery packs are short circuited or severely over charged elemental Lithium may be deposited internally and if the battery pouch is damaged this can escape from inside the battery If this occurs a fire may be caused as elemental Lithium is highly reactive when exposed to water or moisture producing flammable hydrogen gas and corrosive fumes Elemental Lithium is not produced 16 unless the battery pack is severely mistreated so in normal usage there is no likelihood of explosion or fire Lithium lon Polymer battery packs must NEVER be discharged below 3 volts per cell Li Fe 2 0V as this will result in damage to the cells If the voltage is allowed to drop below 3 volts per cell the battery voltage may seem to recover following a charge but the battery may not then give its full nominal capacity and a reduction in performance is likely allowing the voltage to drop
16. from the power source and allow you to adjust the percentage of this power available to each output on the charger This allows the Emperor L702B Pro to deliver the highest available power to each of the charger outputs channels without overloading the power source Each line is selected by pressing the Inc and Dec buttons to move the selection arrow up and down b Power On ESON Emperor L702B Pro v1 www LogicRC com lt INPUT POWER SETTING gt VOLTAGE 12 0V CURRENT 20 0A 1OUTPUT RATE 50 20UTPUT RATE 50 To edit a value press the Enter button to highlight the selected value To increase or decrease the highlighted value press the Inc or Dec buttons Once the desired value has been selected press the Enter button again to store this value Once the correct parameters have been entered press the Esc button to continue to the main screens THE DISPLAY The display is broken up into 2 halves The top half of the display shows the first channel Ch1 and the bottom shows the second Ch2 The selected channel is shown in normal text and the other in reversed out text Ch1 Selected 211 LiPo 3S CHG DCHG 2200mAh 2 1A 4 20V C 10 0A 3 0V C STORE MODE START 3 3A 5mV C DCHG 5 0A 0O 8V C CYCLE CaD 1X 10 gt OJNiMH 6S CHG DCHG CYCLE CH2 Selected gt 11 LiPo 38S CHG DCHG STORE MODE START 2200mAh 2 1A
17. he Emperor L702B Pro has a number of error and warning messages that are designed to advise the user of any problems When applicable pressing the Esc button clears the message SAFETY PRECAUTIONS DO NOT attempt to charge incompatible types of rechargeable batteries This charger is designed to only charge and discharge Nickel Cadmium Nickel Metal Hydride Lithium lon Lithium Polymer LiFePO4 and Lead Acid batteries Make sure you place the charger on a firm level surface for charging DO NOT attempt to charge batteries at excessive fast charge currents Check with your battery manufacturer for the maximum charge rate applicable to your battery DO NOT use automotive type battery chargers to power the charger DO NOT leave the charger unattended while charging Disconnect the battery and remove input power from charger immediately if the charger becomes hot Allow the charger or battery to cool down before reconnecting DO NOT allow water moisture or foreign objects into the charger DO NOT place the battery or charger on or near a flammable object while in use Keep away from carpets cluttered workbenches etc DO NOT cover the air intake holes on the charger as this could cause the charger to overheat Connect the charge lead to the charger BEFORE connecting to the battery DO NOT disassemble the charger This unit is not intended for use by young children or infirm persons unless they have been
18. is selected then press and hold the Enter button for 2 seconds to start the charge As shown in the flow chart above pressing the Mode or Esc buttons at any stage whilst charging moves through the different screens giving detailed information about the charge Pressing the Esc button for 2 seconds at any stage will stop the charge 11 CHARGING A NICD NIMH PACK In the flow chart below we have shown an example of how to charge a 6 cell 7 2V 3000mAh NiMH pack at 4 5 amps using a Normal charge type Press the Inc or Dec buttons to wo change the charge type 1 NiMH 6S 3000mAh CHG 4 5A 5mV C Press and hold the Enter button for 2 seconds to start the charge Press and hold the Enter button for 2 seconds to start NiMH CHARGE 1 NiMH 6S 3000mAh CHG 4 5A 5mV C DCHG 10 0A BATTERY CHECK 3 3A 5 0A 0 8V C CYCLE C2D 1x 10 CYCLE CaD 1X 10 C AUTOMATIC 0 01 12 C AUTOMATIC 0 04 02 C AUTOMATIC 0 05 18 CAPACITY 15mAh Modi INPUT VOLT 14 222V fy BAT TEMP 29 n VOLTAGE 2 PEAK VOLT 8 922V PEAK TEMP 22 1 C CURRENT 7 VOLT gt O NiMH 6S e em 3 3A DCHG 5 0A 0 DCHG 5 0A 0 8V C G 5 0A 0 8V C CYCLE CoD CYCLE CoD 1X 10m CYCLE CoD 1X 10m ESC mue Press and hold the ESC button for 2 seconds to
19. lection arrow It is very important that the correct battery parameters are entered as incorrect values could cause the charger to seriously damage your battery which could result in a fire Pressing the Dec button whilst nothing is highlighted moves the line selection arrow down LITHIUM FUNCTIONS AND PARAMETERS When a Lithium type battery is selected the following functions and parameters are available The 2 and 3 pages shown below are accessed by moving the line selection down arrow off the bottom of the page Charge 11 LiPo 3S 2200mAh CHG a 2 1A 4 20V C Store Mode DCHG 10 0A 3 0V C Discharge STORE MODE 3CUT TEMPER MAX CAPACITY 120 SAFETY TIMER START Cut off Temperature Cut off when x of capacity is reached Cut off if maximum time is reached Max Charge Rate TCS Terminal Capacity Selection What should happen when the TCS capacity is reached TCS END ACT CHG CHARGE This line shows the charge current and the maximum cell voltage which can be edited by press the Enter button to highlight the parameter then the Inc and Dec buttons to edit the value The default charge current for a Lithium battery is set to 1C 1 x capacity however this can be adjusted from 0 1 to 20 Amps N B For safety the charge current is limited to the capacity x charge rate see Maximum Charg
20. on for 2 seconds with this line selected will move to the discharge type selection screen n b The selected discharge current will not be used if Automatic discharge type is selected The cycle mode allows the user to both charge and discharge a battery a number of times in order to bring it back to peak performance Dependant on the final charge state required you have the options to discharge then charge D gt C or charge then discharge C gt D the pack In addition the number of cycles and the delay between charging or discharging can be set n b When cycling a battery the charger will use Automatic charge and discharge currents To start the Cycling you pack hold the Enter button down for 2 seconds MAX CAPACITY MAXIMUM CAPACITY The maximum capacity setting is used to terminate a charge if the charger exceeds the selected percentage of the battery capacity When charging a NiCd or NiMH type pack using delta peak cut off the charger is looking for the pack voltage to peak and then drop off However some packs can give false peaks soon after the charge is commenced Therefore the start peak delay function overrides the peak detection for a selected number of minutes to stop any false peaks being detected The default setting is 3 minutes TRI CURRENT TRICKLE CHARGE CURRENT With NiCd and NiMH type batteries it is recommended that the pack is trickle charged after the main charge has completed so tha
21. t but also comes with balance adaptor boards for JST XH and Flight Power Thunder Power To use an adaptor board connect the supplied balance adaptor board lead to the charger and then connect the board that works with your battery balance connector Optional adaptor boards for Polyquest amp 4 2mm plug car packs are also available If the main battery power leads ONLY are connected to the output banana sockets without connecting the balancing connector to the balancing port on the charger the charger will charge or discharge the connected Lithium pack without balancing it We always recommend balancing a Lithium pack because some cells may retain more capacity than others so over time the pack can become unbalanced If an unbalanced pack is then used some of the cells will exceed their maximum voltage when charged and others their minimum voltage when discharged which causes damage to the cells When a Lithium cell is overcharged it can cause damage and in extreme cases can cause a fire TURNING ON amp SETTING THE INPUT POWER The input power leads on the Emperor are supplied with 4mm gold banana type connectors with optional crocodile clips that should be connected directly to a suitable 11 28V DC power source ensuring that the black connector is connected to the negative and the red to the positive When the charger is initially connected to a power source it will ask you to confirm the maximum input power available
22. t the battery is kept fully charged and is ready to be used Therefore we suggest setting the trickle charge current to around 1096 of the pack capacity SAFETY TIMER The safety timer is used to terminate a charge if it is not completed within the selected time 10 CHARGING With the selection arrow on the CHG line select the correct charge rate and maximum cell peak voltage for the battery being charged then press and hold the CHARGING A LITHIUM PACK In the flow chart below we have shown an example of how to charge a 2S 7 4V 2200mAh LiPo pack at 2 2A Press and hold the Enter button for 2 seconds to start charging el 11 LiPo 2S 2200mAh 3CHG 2 2A 4 20V C DCHG 2 2A 3 0V C LiPo CHARGE t BATTERY dunk CHECK Press the Inc or 3 3A Dec button to 5 0A 0 8V C Ree change the cell CeD number a DES v C TCS 15 0 00 12 C TCS 15 0 01 25 C TCS 15 0 02 59 28 7 687V IS 3 845V CAPACITY 10mAh INPUT VOLT 14 222V fode BAT TEMP 22 1 C fica A VOLTAGE 7 612V PEAK VOLT 7 612V PEAK TEMP 22 1 C AVG VOLT 2 6S gt i 6S s s 5mv C 3 3A H A 5 0A 0 8V C 5 0A 0 et 5 0A 0 8V C CaD 1X 10 H B CaD 1X 10 e ae Press and hold the ESC button for 2 seconds to stop the charge With the line selection arrow on the CHG line check the correct charge current and cell voltage
Download Pdf Manuals
Related Search