Furuno GP1650 User's Manual
Contents
1. 2 Changing Mark Attributes You can select the shapes line types and colors of Marks and Lines on the TRACK display 1 Press the HIDE SHOW key to show the soft key MARK EDIT 2 Press the soft key MARK EDIT to show the MARK LINE window MARK SHAPE MARK LINE MARK COLOR YELLOW MARK LINE window 3 Press the soft key MARK SHAPE to change mark shape the soft key MARK LINE to change mark line or the soft key MARK COLOR to change mark color Mark shape Press the soft key MARK SHAPE to dis play the MARK SHAPE window Press A or W to select mark shape desired MARK SHAPE A O O Oo O O O v MARK SHAPE window Mark line Press the soft key MARK LINE to display the MARK LINE window Press A or to select mark line desired MARK LINE MARK LINE window Mark color Press the soft key MARK COLOR to dis play the MARK COLOR window Press A or to select mark color desired MARK COLOR A RED YELLOW GREEN LIGHT BLUE PURPLE BLUE WHITE MARK COLOR window 4 Press the soft key ENTER or the ENTER key 5 Press the soft key RETURN to finish Marks lines entered hereafter are inscribed in the shape color and line type selected here 3 Changing Mark Size Mark size can be selected from STD stan dard and SMALL 1 Press the MENU key to display the main menu 2 Press the soft key CHART SETUP OP TIONS 3 Press the soft key CHART DETAIL to o2. is useful for estimating the kind of fish school and seabed composition ga A scope 68 3 display 100 Normal _ alisan sounder DNN 159 display A scope display plus normal sounder display 200k New Wide Plotter ES Display This display provides the plotter display on the left part of the screen and the normal sounder display on the right part It is useful for searching fish schools at cruising speed The width of the sounder display can be se lected between standard approx 20 mm and wide approx 40 mm 1 Press the MENU key and the soft key SOUNDER SETUP OPTIONS The sounder setup menu appears See Fig ure 1 9 2 Press W to select E S WINDOW window 3 Press the soft key EDIT to show the E S WINDOW window E S WINDOW A STD Oo WIDE v 13 Press A or VW to select STD or WIDE STD The width of the sounder display is approx 20 mm Default setting WIDE The width is approx 40 mm Press the ENTER key or the soft key ENTER Sounder Plotter Display Display y ACE Plotter Sounder display Dual frequency display example
3. 12 30 1999 LF URUN OPERATOR S MANUAL ADDENDUM Model GP1650 1850 Series Subject New FISHING MODE and Feature Enhancements This Furuno GP1650 1850 Series Plotter has a newly developed software revision that includes many exciting new features This addendum is a supplement to your Operator s Manual It describes these new features and explains how to utilize them fi FURUNO ELECTRIC CO LTD NISHINOMIYA JAPAN TABLE OF CONTENTS A Explanation of New Features 00cccsssecesceeveserees 2 B Operator s Manual Information ccceeeee eesse 3 GC Soltware Revision CGC ie sa ecclesia a EE En 3 D New Fishing Modes and Mark Function 2eeeeee 5 E New Memory Card Storage Function eessseeessseeeseen 8 F Navionics Nav Chart Cartography OFFSET Capability 11 G RTCM DGPS Data Output 1650 1850 D DF ONLY 12 H New Wide Screen E S Mode 1650 1850 F DF ONLY 13 A Explanation of New Features 1 New Fishing Plotter Mode This feature allows you to place your GP1650 1850 in either a Pleasure Mode or a Fishing Mode In the Pleasure Mode the GP1650 1850 operates the same as previous software revisions In the new Fishing Mode you can place Marks and Line Points Up To 5000 in internal memory The mode also allows you to change Track Colors Start Stop Own Ship Tracking and Edit Mark Entries easily from a newly added So
4. OPTIONS The display setup1 menu appears DISPLAY RNG amp BRG MODE RHUMB LINE SETUP1 RANGE SPEED UNIT nm kt DEPTH UNIT ft TEMP UNIT F EDIT LAT LON DISPLAY DD MM MMM TIME DISPLAY 24 HOUR WAYPOINTS SW AUTO2 COURSE VECTOR LINE BEARING MAGNETIC MAG VARIATION AUTO 01 3 E TD DISPLAY LORAN C POSITION DISPLAY LAT LON SET GO TO METHOD 1 POINT gt OPERATION MODE PLEASURE Display setup1 menu 2 Press W to select OPERATION MODE 3 Press the soft key EDIT to show the OP ERATION MODE window OPERATION MODE A PLEASURE O FISHING v OPERATION MODE window 4 Press A or W to select PLEASURE or FISHING 5 Press the soft key ENTER or the ENTER key to finish In the FISHING mode pressing the HIDE SHOW key changes the function of soft keys as follows 34 12 345 N CSE 245 8 135 12 345 E SPD 16 3kt 34 12 345 N CSE 245 8 135 12 345 E SPD 16 3kt Press the HIDE SHOW key Changing displays by Scrolling MARKS 1 Entering Marks Select the Fishing Mode to enable entry of marks on the PLOTTER display Select the location desired with the cursor or turn off the cursor to enter the mark at own ship po sition Pressing the HIDE SHOW key changes the function of soft keys Press the soft key MARK ENTRY to enter a new mark The mark is entered in the shape and color selected from the MARK SHAPE and MARK COLOR selection windows
5. The loaded data OVERWRITES previously stored waypoints and routes BE CAREFUL NOT TO DESTROY VALUABLE DATA Mark line The loaded data is added to internal data When the mark line memory becomes full no marks may be entered Configuration The loaded data replaces current configura tion settings Press the ENTER key to re start If the memory card is ejected while loading or data could not be loaded press the ENTER key to restart with default set tings Note that track memory capacity is not saved or loaded 10 CUSTOMIZING YOUR UNIT This section describes the various options which allow you to set up your unit to suit your needs 1 CHART SETUP OPTIONS menu The chart offset options menu provides three menus chart offset track control and chart detail 1 Press the MENU key to open the main menu 2 Press the soft key CHART SETUP OP TIONS CHART OFFSET TRACK CONTROL CHART DETAIL 11 1 Chart setup options menu 11 CHART OFFSET NEW FOR NAVIONICS In some instances position may be off by a few minutes For example the position of the ship is shown to be at sea while it is in fact moored at a pier You can compensate for this error by offsetting chart position as fol lows 1 Press the MENU key followed by the soft keys CHART SETUP OPTIONS and CHART OFFSET 34 12 345 N FROM 16 41 nm 135 12 345 E OS 276 9 mama Plotter display chart offset select
6. ed 2 Use the cursor pad to place the cursor where to offset chart position 3 Press the soft key SET OFFSET 4 Press the soft key RETURN to finish To cancel chart offset press the soft key RE SET OFFSET at step 3 in the above proce dure TRACK CONTROL menu This menu mainly controls track color and track plotting interval For further details see Track Chapter SETUP NMEA DGPS PORT 2 menu description This menu should be set according to the specifications of the equipment connected to connectors PORT 1 NMEA and PORT 2 DGPS at the rear of the display unit The menu can be displayed by pressing the MENU key followed by the soft keys CON FIGURATION and SETUP NMEA PORT 2 For detailed information see the installation manual FORMAT WITH NEW RTCM OUTPUT Selects data format of connected equipment NMEA0183 version 1 5 version 2 0 RTVM104 EXTRN RTCM104 INTRN or RTCM104 OUTPUT RTCM104 INTRN is for D versions only The default setting for non D versions is RTCM104 EXTRN The procedure for setting LAT LON FORMAT is similar to those for PORT 1 Note that you cannot setup data sentences when you select RTCM104 INTRN as the format A level converter IF 1432 maybe required when using NMEA0183 format from this port LAT LON FORMAT GGA only Selects the seconds of latitude and longitude positions in hundredths thousandths or ten thousandths of a degree UPLOAD DOWNLOAD DATA
7. ftkey Menu In Pleasure Mode this new Softkey Menu is not displayed 2 New Memory Card Storage Capability It is now possible to store Marks Lines Waypoints Routes Tracks and Configuration Information Menu Settings of the GP1650 1850 Series onto a memory card The entire memory contents of a GP1650 1850 can be stored into a single memory card for storage or cloning your GP1650 1850 This provision allows Unlimited Data Storage for the GP1650 1850 Series Uploading Downloading Waypoint information via the RS232 PC Interface has remained unchanged The part number for the RAM Storage Card is 000 140 483 It is available from any authorized Furuno Dealer 3 RTCM DGPS Data Output It is now possible to send RTCM 104 Differential Correction Data to other Differential Ready GPS Products on your vessel This feature requires a D or DF version 4 Navionics Cartography OFFSET Capability This new software allows operators to OFFSET Navionics Charts Previous software versions did not have this capability 5 Wide Screen Echo Sounder Mode When operating in the Split Screen mode Plotter and Sounder display this function allows the user to select between the wide 50 or narrow 25 sounder screen This feature requires a F or DF version B Operator s Manual The Operator s Manual included with your GP1650 1850 is not updated at this time We will offer revised Operator s Manuals late in the fi
8. menu This menu allows you to upload waypoint and route data to a PC or download the same data from a PC via the DGPS connector at the back of display unit The menu can be displayed by pressing the MENU key fol lowed by the soft keys CONFIGURATION and UPLOAD DOWNLOAD DATA For de tailed information see the installation manual See previous pages for Memory Card info 12 DWNLOAD UPLOAD DOWNLOAD WPT RTE TO PC UPLOAD WPT RTE FROM PC SAVE DATA TO MEMORY CARD LOAD DATA FROM MEMORY CARD upload download menu DISPLAY UNIT Connect with PC here Display unit rear view Set communication software on the PC as follows Baud Rate 4800 bps Character Length 8 bit Stop bit 1 bit Parity None X Control XON XOFF The following data can be downloaded up loaded between a personal computer and this equipment e Waypoint data In alphanumeric order e Route data In order of route number e End of sentence Note 1 There are two kinds of data for route data route data and route comment data Note 2 DGPS position fix is not available when uploading or downloading data A scope display This display shows echoes at each transmis sion with amplitudes and tone proportional to their intensities on the right 1 3 of the screen It
9. menu CONFIG Figure 12 3 Test menu SETUP NMEA PORT 1 5 Press the soft key MEMORY I O TEST to start the test Test results and program SETUP NMEA DGPS PORT 2 nos are shown as below UPLOAD DOWNLOAD DATA TEST SYSTEM MENU INTERNAL No LOOK HERE BATTERY OK l GPS ormo e No Doesn t Matter 5 DRAM OK Figure 12 1 Configuration menu BEACON RECEIVER OK PORT1 OK No Doesn t Matter RETURN MENU NOTE Special connections are required to check PORT1 SELF TEST and PORT2 otherwise appears DEMONSTRATION MODE Figure 12 4 Memory I O test results MEMORY CLEAR 6 The test runs continuously To return to the self test menu press the soft key RETURN Note BEACON RECEIVER results only ap pear on GP 1650 1850 D and DF Ver 3 Press the soft key SYSTEM MENU to PORT2 OK No open the system menu Figure 12 2 System menu Changing Operation Mode Operation mode can be changed between PLEASURE and FISHING FISHING mode provides mark line entries on the PLOTTER display Up to 5000 Marks can be entered together with track points Apportioning between track and mark memory can be changed by menu Pressing the HIDE SHOW key changes the function of soft keys Holding tracks changing track color select ing mark colors and the type of marks lines can be performed by the soft keys directly 1 Press the MENU key and the soft key DISPLAY
10. outes e Track e Configration menu settings 1 Formatting Memory Cards Before you can use a memory card it must be formatted Note that formatting always erases all saved data on the card Is Insert the memory card you want to for mat into the slot Press the MENU key followed by the soft keys CONFIGRATION and UPLOAD DOWNLOAD DATA gt TRACK OFF MARK LINE OFF WAYPOINT ROUTE OFF CONFIGURATION OFF SAVE DATA display Press the soft key SAVE DATA TO MEMORY CARD and the soft key FOR MAT You are asked if you are ready to format the memory card Press the ENTER key to format or press the CLEAR key to escape Now FOR MATTING MEMORY CARD appears Do not remove the card while it is being for matting When the formatting is com pleted FORMAT COMPLETED appears Press the ENTER key to finish Now you can record data to the memory card 2 Saving Data to Memory Card The memory card can save four items of data track mark line waypoint route and configu ration Saving data 1 Insert a formatted memory card into the slot Press the MENU key followed by the soft keys CONFIGURATION and UPLOAD DOWNLOAD DATA Press the soft key labeled SAVE DATA TO MEMORY CARD The SAVE DATA display appears 4 Press Aor to select item to save 5 Press the soft key EDIT to open the TRACK MARK LINE WAYPOINTS ROUTES or CONFIGRATION window 6 Press A to
11. pen the CHART DETAIL menu gt LAT LON GRID GREEN TEXT INFO ON WAYPOINT LARGE EDIT WAYPOINT NAME ON INDEX ON or DNE LANDMASS BRT YELLOW BACKGROUND BLUE NAV AIDS ON SECTOR INFO OFF OTHER SYMBOLS WHITE MARK SIZE STD ai CHART DETAIL menu 4 Press W to select MARK SIZE Press the soft key EDIT 6 Press Aor W to select STD standard or SMALL 7 Press the ENTER key 4 Erasing Marks Erasing individual marks lines 1 Operate the cursor pad to place the cur sor on the mark you want to erase 2 Press the CLEAR key The mark se lected is erased Note To erase a line place the cursor on the edge of the line The line segment will be erased Erasing whole marks lines You can erase all marks and lines Be abso lutely sure you want to erase all marks and lines erased marks and lines cannot be re stored 1 Press the MENU key followed by the soft keys CHART SETUP OPTIONS and TRACK CONTROL 2 Press the soft key ERASE MARK You are asked if you are sure to erase all marks and lines 3 Press the ENTER key to erase or press the CLEAR key to escape 5 Displaying Track and Mark Points Number of track and mark points used ap pears in the TRACK STATUS window on the TRACK CONTROL display For further de tails see TRACK CONTROL WINDOW SAVING AND LOADING DATA TO FROM MEMORY CARDS The following data can be saved to memory card e Mark line e Waypoints r
12. rst quarter of 2000 Please call your authorized Furuno Dealer for further information This software revision does not effect the Installation Manual included with your GP1650 1850 C Software Revision Check For Confirmation Only The Software Revision of your GP1650 1850 can be found by using the Self Test procedure on page 4 The Memory I O test will display the software revision number in the upper left corner of the display The last two digits of the number indicate which software version is currently installed If your revision number is lower than the ones listed below a simple software upgrade for any GP1650 1850 is all that is necessary to take advantage of the new features available Call your local Furuno Dealership for more information GP1650 GP1650D Software Version 145 1801 013 and higher GP1650F GP1650DF Software Version 145 1802 011 and higher GP1850D Software Version 145 1826 006 and higher GP1850DF Software Version 145 1827 006 and higher Diagnostic Tests 4 Press the soft key SELF TEST to open the test menu Memory I O port test This test conducts a general check of the dis play unit and the antenna unit The unit dis MEMORYeI O TEST plays the results for each device or ENBOR component checked as OK or NG No Good Keveoaro test 1 Press the MENU key to open the main TestratrerN menu REMOTE CONTROLLER TEST 2 Press the soft key CONFIGURATION to show the configuration
13. select ON 7 Press the soft key ENTER or the ENTER key Repeat from steps 4 to 7 to save other data if desired Press the soft key SAVE DATA The fol lowing message appears and saving starts Do not remove the memory card while data is being saved NOW SAVING DATA TO MEMORY CARD DO NOT TURN OFF THE POWER UNTIL SAVING COMPLETED SAVE DATA message When saving is completed COM PLETE SAVING DATA appears 10 Press the ENTER key Error message Memory card not inserted Press the ENTER key to return to the SAVE DATA display MEMORY CARD NOT INSERTED INSERT CARD PRESS ENTER key TO CONTINUE NOT INSERTED message Unformatted memory card Press the ENTER key to return to the SAVE DATA display And format it refering to the previous page MEMORY CARD NOT FORMATTED PRESS ENTER key TO CONTINUE NOT FORMATTED message Wrong card inserted Appears when a chart card is inserted Press the ENTER key to return to the SAVE DATA display Replace it with a formatted memory card WRONG CARD INSERTED INSERT MEMORY CARD PRESS ENTER key TO CONTINUE WRONG CARD message Data overwrite Data type to be recorded exists on memory card Two or more of same data type can not be recorded Press the ENTER key to overwrite same data type on the card or press the CLEAR key to escape OVERWRITE FOLLOWING DATA OK A TRACK YES ENTER key NO CLEAR ke
14. y OVERWARITE message 3 Loading Data from Memory Card Data track marks waypoints configuration can be loaded from a memory card and dis played on the screen This feature is useful for observing past data and setting up the equipment for a specific purpose with con figuration 1 Press the MENU key followed by the soft keys CONFIGURATION and UPLOAD DOWNLOAD DATA 2 Press the soft key LOAD DATA FROM MEMORY CARD to show the LOAD DATA display gt TRACK OFF MARK LINE OFF WAYPOINT ROUTE OFF CONFIGURATION OFF LOAD DATA display 3 Press A or W to select item to load 4 Press the soft key EDIT to show the ON OFF selection window 5 Press A to select ON Press the soft key ENTER or the ENTER key If the memory card does not contain the item selected the buzzer sounds and ON can not be selected 6 After you select all items desired press the soft key LOAD DATA to load data The following message appears NOW LOADING DATA FROM MEMORY CARD DO NOT TURN OFF THE POWER UNTIL LOADING COMPLETE LOAD DATA message After loading is completed the following message appears COMPLETE LOADING DATA PRESS ENTER KEY TO CONTINUE COMPLETE message 7 Press the ENTER key Note on loading data Track Since loaded track data is added to internal track oldest track will be erased when the track memory capacity is exceeded Waypoint route
Download Pdf Manuals
Related Search