Fujitsu B2620 User's Manual
Contents
1. Menu Field Default Menu Field Default BIOS Version 1 31 L1 Cache 32 KB BIOS Date 08 26 2002 L2 Cache 512 KB BIOS Area EOOOh FFFFh Total Memory 256 MB CPU Type Pentium R Ill processor M Memory Slot 256 MB SDRAM CPU Speed 850 MHz 32 EXIT MENU LEAVING THE SETUP UTILITY The Exit Menu is used to leave the setup utility Follow the instructions for Navigating Through The Setup Utility to make any changes PhoenixBIOS Setup Utility Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit System Setup and save your changes to CMOS Select Item Change Values Setup Defaults Select Menu Select Sub Menu Save and Exit Figure 21 Exit Menu The following table shows the names of the menu fields for the Exit menu the default settings and a description of the field s function and any special information needed to help understand the field s use Table 21 Fields Options and Defaults for the Exit Menu Optional mee Menu Field Keyboard Shorteut Description Exit Saving Press the F10 key Exit Saving Changes and Exit will store all the entries on every menu of the setup Changes utility to the BIOS memory and then exit the setup utility A confirmation message Save Configuration changes and exit now Yes No willbe displayed Exit Dis Selecting Exit Discarding Changes and Exit wil2. Menu Field Options Default Description Serial Port e Disabled Enabled Configures the serial port using either no configuration e Enabled Disabled a user defined configuration Enabled or by e Auto allowing the BIOS or OS to choose the configuration Auto 1 0 Address e 3F8 3FF 3F8 3FF Allows user to set the serial port base 1 O address when e 2F8 2FF serial port is Enabled e 3E8 3EF e 2E8 2EF Interrupt e IRQ3 IRQ 4 Allows user to set the serial port interrupt when serial port e IRQ4 is Enabled e IRQ5 Infrared Port e Disabled Enabled Configures the infrared port using either no configuration e Enabled Disabled a user defined configuration Enabled or by e Auto allowing the BIOS or OS to choose the configuration Auto Mode e IrDA FIR When the infrared port is enabled this option is available e FIR allowing the user to set the mode for the infrared port 1 O Address e 3F8 3FF 2E8 2EF Allows user to set the infrared port I O address when the e 2F8 2FF infrared port is Enabled e 3E8 3EF e 2E8 2EF Interrupt e IRQ3 IRQ 3 Allows user to set the infrared port interrupt when the e IRQ 4 infrared port is Enabled IRQ5 1 O address e 100 107 118 11F Allows user to set the infrared port 1 O address when the e 108 10F infrared port is Enabled e 110 117 e 118 11F DMA Channel e DMA 1 DMA 3 Allows user to set the infrared port DMA Channel when e DMA 3 the
3. System Date Sets and displays the current date Date is in a month day year numeric format with 2 digits each for month and day and 4 digits for year MM DD YYYY for example 03 20 1998 You may change each segment of the date separately Move between the segments with the Tab key and or Shift Tab keys Floppy Disk A e Disabled Disabled Enables or disables floppy disk A 1 44 1 2 MB 3 5 Primary Master e Selects Primary TOSHIBA Displays the type of device on this ATA ATAPI inter Master MK4018GAP PM face if there is one Pressing the Enter key selects the submenu Primary Master submenu allowing additional device configuration options for this interface Language e English US English US The default setting differs between the US European e Japanese JP and the Japanese model Selects the display language for the BIOS po B Series Notebook BIOS Primary Master Submenu of the Main Menu The Primary Master submenu identifies what ATA ATAPI devices are installed Table 2 Fields Type Maximum Capacity Note Actual hard drive label shown may vary Depending on the drive type information such as cylinders heads and sectors may or may not be displayed PhoenixBIOS Setup Utility Primary Master TOSHIBA MK4018GAP PM Item Specific Help 40008MB Multi Sector Transfers 16 Sectors LBA Mode Control PIO Transfer Mode DMA Transfer Mode Select Ite
4. Resume Time gt Advanced Features Select Item Select Menu Security Power Customi zed 4 Minutes 15 Minutes 00 00 00 Change Values Select Sub Menu Boot Info Exit Item Specific Help Select Power Management Mode Choosing modes changes system power management settings Maximum Power Savings conserves the greatest amount of system power while Maximum Performance conserves power but allows greatest system performance To alter these setting choose Customize To turn off power management choose Disabled Setup Defaults Save and Exit Figure 16 Power Menu 26 Table 16 Fields Options and Defaults for the Power Menu for APM operating systems only Menu field Options Default Description Power e Disabled Customized Sets the power savings parameters to a factory installed Savings e Customized combination of parameters a custom set of parameters set by e Maximum you or no power saving features Power Savings e Maximum Performance Hard Disk Off Off Sets the length of time that the hard drive can be inactive Timeout e 30 seconds to before your notebook automatically turns off the power to the 20 Minutes hard drive controller and drive motor If you choose a factory installed combination of parameters this field will display the setting If you choose to customize the parameters you will be able to set this yourself The options available vary f
5. Utility to make any changes The following tables show the names of the menu fields for the Boot menu and its submenu all of the options for each field the default settings and a description of the field s function and any special information needed to help understand the field s use PhoenixBIOS Setup Utility Quick Boot Boot Time Diagnostic Screen Preboot Execution Environment gt Boot Device Priority Select Item Select Menu Disabled Disabled Change Values Select gt Sub Menu Item Specific Help Disabled All diagnostic tests will be done Enabled Some diagnostic tests may be skipped while booting to speed up Auto Diagnostic tests will be automatically skipped or done according to the order of the ACPI OS Setup Defaults Save and Exit Figure 18 Boot Menu Table 18 Fields Options and Defaults for the Boot Menu Menu Field Options Default Description QuickBoot e Disabled Enabled Turns on and off booting with a truncated set of Power On e Enabled Self Test Fewer tests mean faster turn on e Auto Boot time e Disabled Disabled Turns on and off display of test results instead of Fujitsu Diagnostic Screen e Enabled logo screen during Power On Self Test Preboot Execution e Disabled Disabled Turns on and off the preboot execution environment Environment e Enabled feature Note that if your system has a wireless LAN installed this field may
6. for legacy ISA devices and to enable or disable built in PCI device modules PhoenixBIOS Setup Utility Advanced PCI Configurations Item Specific Help gt IRQ Reservation Reserve specific IRQs for use by legacy ISA devices Select Item Change Values Setup Defaults Select Menu Select Sub Menu Save and Exit Figure 8 PCI Configurations Submenu Table 8 Fields Options and Defaults for the PCI Configurations Submenu of the Advanced Menu Menu Field Options Default Description IRQ Reservation Reserve specific IRQs for use by legacy ISA devices 17 po B Series Notebook BIOS IRQ Reservation Submenu of the PCI Configurations Submenu The IRQ Reservation submenu of the PCI Configura tions submenu allows the user to mark various IRQs as wy CAUTION reserved for use by legacy ISA devices When an IRQ is Only IRQ s 9 10 amp 11 can be reserved without conflict reserved the BIOS does not use it for embedded PCI or ISA devices PhoenixBI0S Setup Utility Advanced IRQ Reservation Item Specific Help lavailablell Reserve the specified Available IRQ for use by legacy Available ISA devices Available Available Available Available Available Help Select Item Change Values Setup Defaults Exit Select Menu Select gt Sub Menu Save and Exit Figure 9 IRQ Reservation Submenu Table 9 Fields Options and Defaults for the IRQ Reserva
7. 2 To select a field within a menu or a submenu use the cursor keys 4 y 3 To select the different values for each field press the Spacebar or to change to the next higher selec tion and F5 or to go to the next lower selection 4 To activate a submenu press the Enter key 5 To return to a menu from a submenu press the Esc key 6 To go to the Exit menu from any other menu press the Esc key Points Selecting a field causes a help message about the field to be displayed on the right hand side of the screen e Pressing the Enter key with the highlight on a selec tion that is not a submenu or auto selection will cause a list of all options for that item to be displayed Pressing the Enter key again will select the high lighted choice 7 Pressing the F9 key resets all items in the BIOS to the default values 8 Pressing the F10 key saves the current configura tion and exits the BIOS Setup Utility You will be asked to verify this selection before it is executed 9 Pressing the F1 key gives you a general help screen Entering the Setup Utility After a Configuration Change or System Failure If there has been a change in the system configuration that does not match the parameter settings stored in your BIOS memory or there is a failure in the system the system beeps and or displays an error message after the Power On Self Test POST If the failure is not too severe i
8. Advanced When selected opens the Advanced Features submenu which Features allows setting additional power saving parameters Factory Installed Values for Power Saving Profiles Hard Disk Video Standby Auto Suspend Timeout Timeout Timeout Timeout Customized Off Off 4 Minutes 15 Minutes Maximum Power Savings 30 Seconds 2 Minutes 1 Minute 5 Minutes Maximum Performance Off Off Off 15 Minutes Disabled Off Off Off Off Sample Customized Profile To get even better 2 Minutes 1 Minute 1 Minute 5 Minutes battery life keep the display and volume settings as low as possible and use the sample custom ized profile 28 Advanced Features Submenu of the Power Menu The Advanced Features submenu is for setting some non time related power saving parameters PhoenixBIOS Setup Utility Advanced Features Item Specific Help Suspend Resume Switch lEnabledll Configures the Lid Closure Suspend on Suspend Resume switch Lid Open Resume off Resume on LAN Off Serial Mouse Activity Disabled Performance Control Fixed Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 17 Advanced Features Submenu Table 17 Fields Options and Defaults for the Advanced Features Submenu of the Power Menu Menu Field Options Default Description Suspend Resume e Disabled Enabled Sets the function of the Suspend Resume button when your no
9. infrared port is Enabled Parallel Port e Disabled Enabled Configures the parallel port using either no configuration e Enabled Disabled a user defined configuration Enabled or by e Auto allowing the BIOS or OS to choose the configuration Auto 11 po B Series Notebook BIOS Table 4 Fields Options and Defaults for the Serial Parallel Port Configurations Submenu of Advanced Menu Menu Field Options Default Description Mode e Output Only Bi directional When the parallel port is enabled this option is available e Bi directional allowing the user to set the mode for the parallel port Bi e ECP directional allows two way transfer of information between your notebook and a connected parallel device Output Only Half Duplex allows information to be trans ferred in only one direction from your notebook to the printer or similar device ECP Mode allows communication with the ECP class of parallel 1 O devices I O address e 378 37F 378 37F Allows user to set the parallel port base I O address when e 278 27F the parallel port is Enabled e 3BC 3BF Interrupt e IRQ5 IRQ 7 Allows user to set the parallel port interrupt when the par e IRQ7 allel port is Enabled 12 Advanced Menu Keyboard Mouse Features Submenu of the Advanced Menu Keyboard Mouse Features submenu is for setting parameters of the integrated and external mouse and keyboard PhoenixBIOS Se
10. needed system parameters Follow the instructions for to help understand the field s use Navigating Through The Setup Utility to make any changes a point The following tables show the names of the menu fields System Time and System Date can also be set from your for the Main menu and its submenus all of the options operating system without using the setup utility Use for each field the default settings and a description of the calendar and time icon on your Windows Control panel Figure 1 Main Menu PhoenixBIOS Setup Utility Advanced Security Power Boot Info Exit Item Specific Help System Time NX1 57 01 System Date 10 25 2002 F 5 Adjust calendar clock Floppy Disk A Disabled lt Tab gt lt Shift Tab gt or gt Primary Master TOSHIBA MK4018GAP PM Ent orebecloctarricldl Language English US Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Table 1 Fields Options and Defaults for the Main Menu Menu Field Options Default Description System Time Sets and displays the current time Time is in a 24 hour format of hours minutes seconds with 2 digits for each HH MM SS Example 16 45 57 You may change each segment of the time separately Move between the segments with the Tab key and or Shift Tab keys Table 1 Fields Options and Defaults for the Main Menu Menu Field Options Default Description
11. not be present Boot Device e Selects the Boot This menu allows setting up the source for the operating Priority Device Priority system submenu 30 Boot Device Priority Submenu of the Boot Menu The Boot Device Priority submenu is for setting the order of checking of sources for the operating system PhoenixBIOS Setup Utility Boot Device Priority Item Specific Help The top device has the Floppy Disk Drive highest priority Hard Disk Drive lt Enter gt expands or collapses devices with a or lt Ctrl Enter gt expands all lt T gt or lt J gt selects a device lt gt lt Space gt or lt gt moves the device up or down lt Shift 1 gt enables or disables a device Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 19 Boot Device Priority Submenu Table 19 Fields Options and Defaults for the Boot Device Priority Submenu of the Boot Menu Menu Field Options Description Floppy Disk The boot selections determine the order in which the BIOS Drive searches for the operating system during a startup sequence To change the order highlight one source by using the up or down cursor keys and then press the or key to change the order number for that source Be sure to save your changed order when you exit the BIOS setup utility Hard Disk e TOSHIBA MK4018GAP PM Drive e Bootable Add in Cards Exit
12. 1 e Ultra DMA 2 Exiting from Main Menu When you have finished setting the parameters on this menu you can either exit from the setup utility or move to another menu If you wish to exit from the setup utility press the Esc key or use the cursor keys to go to the Exit menu If you wish to move to another menu use the cursor keys po B Series Notebook BIOS ADVANCED MENU SETTING DEVICE FEATURE CONTROLS The Advanced Menu allows you to e Configure CPU features e Configure USB features Follow the instructions for Navigating Through The Setup Utility to make any changes Enable or disable support for Plug amp Play operating systems Set the I O addresses for the serial and parallel ports Set the communication mode for the parallel port and The following tables show the names of the menu fields infrared port for the Advanced Menu and its submenus all of the Select between the display panel and an external options for each field the default settings and a descrip CRT display tion of the field s function and any special information Enable or disable compensation for your display needed to help understand the field s use e Configure PCI devices in your system PhoenixBIOS Setup Utility Advanced Security Power Boot Info Exit Item Specific Help Plug Play 0 S iNo Protected Device Configurations No No gt Serial Parallel Port Configurations The BIOS configures gt Keyboard Mouse
13. Features also non boot devices gt Video Features Select if you are using gt Internal Device Configurations a non Plug amp Play OS or gt PCI Configurations a non ACPI OS gt CPU Features p gt USB Features Yes The BIOS configures pEvent Logging only boot devices Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 3 Advanced Menu Advanced Menu Table 3 Fields Options and Defaults for the Advanced Menu Configuration Menu Field Options Default Description Plug amp Play O S e No No Select Yes if you are using a Plug amp Play capable operating system Select e Yes No if you need the BIOS to configure non boot devices Protected e No No No allows Plug amp Play operating system to change device system settings Device e Yes Yes prevents a Plug amp Play operating system from changing system set tings ACPI operating system ignores this setting Serial Parallel Port Configurations When selected opens the Serial Parallel Port Configurations submenu which allows the user to modify settings for serial infrared and parallel ports Keyboard Mouse Features When selected opens the Keyboard Mouse Features submenu which allows setting external and internal keyboard and mouse parameters Video Features When selected opens the Video Features submenu which allows setting of the display parameters including routing of video s
14. avigating Through The Setup Utility to make any changes Points e If you set a password write it down and keep it ina safe place If you forget the password you will have to contact your support representative to regain access to your secured functions and data e If you make an error when re entering the password a Warning will be displayed on the screen To try Entering a password incorrectly three times in a row will cause the keyboard and mouse to be locked out and the warning System Disabled to be displayed If this happens restart the computer by turning off and on the power with the power switch and use the correct password on reboot If the Password on Resume is Enabled and the Pass word on Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or Save to Disk modes Power Management Security will work only if Password on Boot is enabled again press the Enter key and then retype the pass word Press the Esc key to abort the password setting process Boot sector protection must be set to Normal to install or upgrade an operating system The following tables show the names of the menu fields for the Security menu and submenus all of the options for each field the default settings and a description of the field s function and any special information needed to help understand the field s use The default condition is no passwords required and no wr
15. d disk cannot be read on any systems other than the original system on which it was locked or on systems that have the identical password setting 24 Owner Information Submenu of the Security Menu The Owner Information submenu is for setting owner information PhoenixBI0S Setup Utility Advanced Security Power Boot Info Exit Item Specific Help Owner Information Is Clear Set Owner Information Enter Foreground Color Gray Background Color Black Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 15 Owner Information Submenu Table 15 Fields Options and Defaults for the Owner Information Submenu of the Security Menu Menu Field Options Default Description Owner Information Clear Display only Is Set Owner Enter Field to write owner Information information i e name Foreground Color e Black e Brown e Light Cyan Gray e Blue e White e Light Red e Green e Gray e Light Magenta e Cyan e Light Blue e Light Yellow e Red e Light e Bright White e Magenta Green Background Color e Black e Brown e Light Cyan Black e Blue e White e Light Red e Green e Gray e Light Magenta e Cyan e Light Blue e Light Yellow e Red e Light e Bright White e Magenta Green 25 po B Series Notebook BIOS POWER MENU SETTING POWER MANAGEMENT FEATURES The Power menu allows you to set and change the power management parameters Follo
16. ignals to different displays Internal Device Configurations When selected opens the Internal Device Configurations submenu which allows enabling or disabling the Floppy Disk IDE and LAN Controllers PCI Configurations When selected opens additional menus to configure PCI devices CPU Features Configures Processor Serial Number features of Pentium R III processor LifeBooks with the Intel SpeedStep software pre installed will provide the user the ability to set the processor performance CPU Features When selected opens the CPU Features submenu which allows setting of Intel SpeedStep features USB Features When selected opens the USB Features submenu which allows enabling or disabling USB Event Logging When selected opens the event logging submenu po B Series Notebook BIOS Serial Parallel Port Configurations Submenu of the Advanced Menu The Serial Parallel Port Configurations submenu provides the ability to set the I O addresses and interrupt levels for the serial infrared and parallel ports of your notebook Y CAUTION 1 O addresses DMA channels and Interrupt levels can be entered in various ways including via the BIOS setup utility the control software for the I O device or the hardware If any two ports or devices serial or parallel have the same I O address assigned your notebook will not function normally Please keep a record of original sett
17. ing from Boot Menu When you have finished setting the boot parameters with the Boot menu you can either exit from the setup utility or move to another menu If you wish to exit from the setup utility press the Esc key to go to the Exit menu If you wish to move to another menu use the cursor keys 31 pos B Series Notebook BIOS INFO MENU DISPLAYS BASIC SYSTEM INFORMATION The Info menu is a display only screen that provides the configuration information for your notebook The following table shows the names of the menu fields for the Info menu and the information displayed in those fields These fields are for information purposes only and are not editable except for the Asset Number as in the Point below Points e The asset number is an optional user entered field and can be entered through the use of third party DMI Compliant software such as LANdesk Client Manager e The information displayed on this screen is variable according to the unit you purchased PhoenixBI0S Setup Utility BIOS Version alo cl BIOS Date 08 26 2002 BIOS Area E000h FFFFh CPU Type CPU Speed 850 MHz L1 Cache 32 KB L2 Cache 512 KB Total Memory 256 MB Memory Slot 256 MB SDRAM Select Item Select Menu Item Specific Help Pentium R 111 processor M Change Values Select gt Sub Menu Figure 20 Info Menu Table 20 Fields Options and Defaults for the Info Menu Setup Defaults Save and Exit
18. ings before making any changes in the event that a restoration is required See your hardware and software documentation as well as the setup utility to determine settings limitations etc points e To prevent IRQ and address conflicts avoid changing the default settings If you must change the settings you can call 1 800 8FUJITSU for technical assistance e The BIOS will warn you of a resource conflict by plac ing a yellow asterisk next to each device that is in conflict e All I O addresses in Table 4 are in hexadecimal PhoenixBIOS Setup Utility Advanced Serial Parallel Port Configurations Item Specific Help Serial Port I O Address Interrupt Infrared Port Mode I O Address Interrupt I O Address DMA Channel Parallel Port Mode I O Address Interrupt IRQ 2E8 IRQ 118 DMA 378 IRQ Select Item Select Menu 4 3 3 7 Enabled 3F8 3FF Enabled FIR 2EF 11F Enabled Bi directional 37F Change Values Select Sub Menu Disabled The port is disabled Enabled The port is enabled with user configuration Auto The port is configured depending on Plug amp Play 0S setting Setup Defaults Save and Exit Figure 4 Serial Parallel Port Configurations Submenu 10 Advanced Menu Table 4 Fields Options and Defaults for the Serial Parallel Port Configurations Submenu of Advanced Menu
19. ite protection PhoenixBIOS Setup Ut Security Supervisor Password Is Clear User Password Is Clear Set Supervisor Password ETS Set User Password Enter Minimum User Password Length 0 Password on Boot Disabled Boot from Removable Media A11 Floppy Disk Access A11 Hard Disk Security Owner Information Hard Disk Boot Sector Normal Security Panel on Resume Enabled Select Item Change ility Item Specific Help Press lt Enter gt key to set Supervisor password to enable any password features Then password entry is required to enter BIOS Setup Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 13 Security Menu 22 Table 13 Fields Options and Defaults for the Security Menu Menu Field Options Default Description Supervisor Clear A display only field Set is displayed when the system supervisor pass Password is word is set and Clear when it is not User Password is Clear A display only field Set is displayed when the general user password is set and Clear when it is not Set Supervisor Enter Sets changes or cancels Supervisor Password Supervisor Password may Password be up to seven characters long and must include only letters or numbers no symbols Passwords are NOT case sensitive To cancel a password press Enter instead of entering characters in the Enter New Password field and in
20. l exit the setup utility with out writ carding ing to the BIOS memory When the BIOS recognizes this selection it will load the Changes operating system and begin operation Load Setup Press the F9 key Selecting Load Setup Defaults will load the factory preset default values for all Defaults menu fields then display the message Load default configuration now Yes No When confirmed the setup utility will return to the Exit Menu To return to another menu follow the directions in the Navigating Through The Setup Utility section 33 po B Series Notebook BIOS Table 21 Fields Options and Defaults for the Exit Menu Optional Field Descripti Menu Fie Keyboard Shortcut escription Discard Selecting Discard Changes loads the previous values in BIOS memory for all menu Changes fields The message Load previous now Yes No will be displayed When confirmed the setup utility will return to the Exit menu To go to another menu follow the directions in the Navigating Through The Setup Utility section Save Selecting Save Changes will cause the new settings in all menus to be written to Changes the BIOS memory The message Save configuration changes now Yes No will be displayed When confirmed the setup utility will return to the Exit menu To return to another menu follow the directions in the Navigating Through The Setup Utility section 34
21. m Select Menu Enabled FAST PIO 4 Ultra DMA 2 Select ATA ATAPI drive installed here Auto The BIOS auto types the drive on boot time Except Auto You enter parameters of the drive None The drive is disabled Change Values Setup Defaults Select gt Sub Menu Save and Exit Figure 2 Primary Master Submenu Options and Defaults for the Primary Master Submenu of the Main Menu Menu Field Options Default Description Type e Auto Auto Selects the ATA ATAPI device type Select Auto to have the e None type automatically identified by the BIOS at POST If None is e Hard Disk selected all of the following Set up items do not appear If Hard Disk is selected you must specify the number of Cylin ders Heads and Sectors for the drive Cylinders e A number This item appears only when the type is identified as Hard between 0 Disk When Hard Disk is selected you can change the value and 65 535 This field is changed by incrementing pressing the Space bar or by typing in the number Heads e A number This item appears only when the type is identified as Hard between 1 Disk When Hard Disk is selected you can change the value and 16 This field is changed by incrementing pressing the Space bar or by typing in the number Table 2 Fields Options and Defaults for the Primary Master Submenu of the Main Menu Menu Field Options Default Descri
22. meters to the hard drive before Suspend Mode to turning your notebook to the pseudo off condition Save to Disk mode Auto Save e Off Off When setto After 1 Hour your notebook will auto to Disk e After 1 Hour matically save all system memory and the operating parameters to the hard drive and go to pseudo off if the notebook is left in Suspend mode for more than an hour Resume On e Off Off Sets whether or not to Resume from a suspension state when a Modem e On message is received by telephone line This feature will not Ring operate if the Save to Disk mode is enabled This feature applies to internal and external modems 27 po B Series Notebook BIOS Table 16 Fields Options and Defaults for the Power Menu for APM operating systems only Menu field Options Default Description Resume On e Off Off Sets whether or not to resume from a suspension state at a des Time e On ignated time This feature is available from either the Suspend or Save to Disk modes Resume 00 00 00 Sets the designated time on a 24 hour clock when the note Time book is to automatically resume operation from the Suspend state The format of the clock setting is hours minutes seconds Each segment of the time is set separately either by increment ing or by typing in the numbers You move between the seg ments with the Tab key or the Shift Tab keys This only applies when Resume on Time is set to On
23. n All is selected floppy disk access is not restricted Hard Disk Configures hard disk security features Security Owner a Sets Owner information Information Hard Disk Boot e Normal Normal Sets protection mode for hard disk drive Sector e Write Protected Security Panel e Disabled Enabled Allows you to enable or disable the Security Panel feature upon Resume on Resume e Enabled from Suspend Exiting from the Security Menu When you have finished setting the parameters on the Security Menu you can either exit from setup utility or move to another menu If you wish to exit from setup utility press the Esc key to go to the Exit Menu If you wish to move to another menu use the cursor keys 23 po B Series Notebook BIOS Hard Disk Security Submenu of the Security Menu The Hard Disk Security submenu is for configuring hard disk security features PhoenixBIOS Setup Utility Security Hard Disk Security Item Specific Help Primary Master Disabled Select Item Select Menu Change Values Setup Defaults Select gt Sub Menu Save and Exit Figure 14 Hard Disk Security Submenu Table 14 Fields Options and Defaults for the Hard Disk Security Submenu of the Security Menu Menu Field Options Default Description Primary Master e Disabled Disabled Disabled No password protection e Enabled Enabled Hard drive is locked with the password Data in the locke
24. nables or disables compensation which controls spacing e Enabled on the display When enabled displays with less than pixel resolution 800 x 600 will still cover the entire screen 15 poe B Series Notebook BIOS Internal Device Configurations Submenu of the Advanced Menu The Internal Device Configurations submenu allows the user to configure other internal devices PhoenixBIOS Setup Utility Internal Device Configurations Item Specific Help Floppy Disk Controller PERA Disabled IDE Controller Enabled Floppy disk drive is LAN Controller Auto disabled Enabled Floppy disk drive is enabled Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 7 Internal Device Configurations Submenu Table 7 Fields Options and Defaults for Internal Device Configurations Submenu of Advanced Menu Menu Field Options Default Description Floppy Disk e Disabled Disabled Enables or disables the Floppy Disk Drive Controller e Enabled IDE Controller e Disabled Enabled Enables or disables selected IDE devices e Enabled LAN Controller e Enabled Auto Enables or disables LAN controller e Disabled NOTE This field may not be present if you have a wireless e Auto LAN installed 16 Advanced Menu PCI Configurations Submenu of the Advanced Menu The PCI Configurations submenu allows the user to reserve specific interrupts IRQs
25. nel Disabled Quick Point Enabled External PS 2 Mouse Enabled Configuration 4 Touch Panel Disabled Quick Point Exclusive Enabled External PS 2 Mouse Enabled 13 po B Series Notebook BIOS Table 5 Fields Options and Defaults for the Keyboard Mouse Features Submenu of the Advanced Menu Menu Field Options Default Description Initialization on e Fast Fast When Fast is selected the initialization of external PS Resume e Normal 2 devices is optimized to speed up on resume When Normal is selected initialization is not optimized Note that this feature is designed for Windows XP systems only When external PS 2 devices don t function after resume set to Normal 14 Advanced Menu Video Features Submenu of the Advanced Menu The Video Features Submenu is for setting the display parameters PhoenixBIOS Setup Utility Advanced Video Features Item Specific Help Display liInternal Flat Panell Select display terminal Compensation Disabled Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 6 Video Features Submenu Table 6 Fields Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Options Default Description Display e Internal Internal Selects where the video signal will be routed Flat Panel Flat Panel e External e Simultaneous Compensation e Disabled Disabled E
26. oy FUJITSU Fujitsu LifeBook B Series BIOS Guide LifeBook B Series Model B2620 Document Date 10 30 02 Document Part Number FPC58 0792 01 FUJITSU PC CORPORATION po B Series Notebook BIOS B Series BIOS BIOS SETUP UTILITY The BIOS Setup Utility is a program that sets up the operating environment for your notebook Your BIOS is set at the factory for normal operating conditions therefore there is no need to set or change the BIOS environment to operate your notebook The BIOS Setup Utility configures Device control feature parameters such as changing T O addresses and boot devices e System Data Security feature parameters such as passwords Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following 1 Turn on or restart your notebook 2 Press the F2 key once the Fujitsu logo appears on the screen This will open the main menu of the BIOS Setup Utility with the current settings displayed 3 Press the RIGHT ARROW or LEFT ARROW key to scroll through the other setup menus to review or alter the current settings Navigating Through The Setup Utility The BIOS setup utility consists of seven menus Main Advanced Security Power Boot Info and Exit This document explains each menu including all submenus and setup items The following procedures allow you to navigate the setup utility menus 1 To select a menu use the cursor keys gt
27. ption Sectors A number This item appears only when the type is identified as Hard between 0 Disk When Hard Disk is selected you can change the value and 63 This field is changed by incrementing pressing the Space bar or by typing in the number Maximum e Display only Displays the maximum capacity of the drive calculated from Capacity the parameters of the hard disk when Hard Disk is selected Multi Sector e Disabled 16 Sectors This option cannot be changed when Auto is selected Specify Transfers e 2 Sectors the number of sectors per block for multiple sector transfer e 4 Sectors e 8 Sectors e 16 Sectors e 32 Sectors e 64 Sectors e 128 Sectors LBA Mode e Disabled Enabled Enables or disables logical Block Addressing in place of Cylin Control e Enabled der Head Sector addressing This option cannot be changed when Auto is selected PIO Transfer e Standard Fast PIO 4 Selects the method for moving data to from the drive Auto Mode e Fast PIO 1 type the drive to select the optimum transfer mode This e Fast PIO 2 option cannot be changed when Auto is selected Multi word e Fast PIO 3 DMA is automatically set to mode 1 for Fast PIO 1 Fast PIO e Fast PIO 4 2 Fast PIO 3 and set to mode 2 for Fast PIO 4 DMA DMA Transfer e Disabled Ultra DMA 2 Selects the method for moving data to from the drive Mode e Multiword This option cannot be changed when Auto is selected DMA 1 e Multiword DMA 2 e Ultra DMA O e Ultra DMA
28. r the CPU Features Submenu of the Advanced Menu Menu Field Options Default Description Intel R e Auto Auto When Auto is selected the CPU speed is determined by SpeedStep R e Max Perf the power source used When Max Perf is selected CPU Technology e Batt Opt speed is maximized When Batt Opt is selected CPU e Disabled speed is optimized for battery operation When Disabled is selected CPU speed is fixed to battery optimized speed 19 po B Series Notebook BIOS USB Features Submenu of the Advanced Menu The USB Features submenu configures the USB capabilities of the system PhoenixBIOS Setup Utility Advanced USB Features Item Specific Help USB Floppy Disk Disabled Legacy Floppy Emulation is disabled Enabled Legacy Floppy Emulation is enabled and USB floppy is available without USB aware OS Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 11 USB Features Submenu Table 11 Fields Options and Defaults for the USB Features Submenu of the Advanced Menu Menu Field Options Default Description USB Features e Disabled Enabled When enabled Legacy Floppy Emulation is enabled e Enabled 20 Advanced Menu Event Logging Submenu of the Advanced Menu The Event Logging submenu is for setting up the logs for DMI event logging Advanced PhoenixBIOS Setup Utility Nin aca ea Event Log Capaci
29. rom Off which has no inactivity shutoff to 20 minutes Display e Off Off Sets the length of time without any user input device activity Timeout e 2to20 before the display is turned off If you choose a factory Minutes combination of parameters this field will display the setting If you choose to customize the parameters you will be able to set this yourself Off has no inactivity shutoff Standby e Off 4 Minutes Sets the length of time without any user input device activity Timeout e 1to16 before the CPU is set to half speed and the display and the hard Minutes drive are turned off If you choose a factory combination of parameters this field will display the setting If you choose to customize the parameters you will be able to set it yourself Auto Sus e Off 15 Minutes Sets the length of time without any 1 O activity before your pend e 5to60 notebook goes into Suspend mode If you choose a factory Timeout minutes combination of parameters this field will display that setting If you choose to customize the parameters you will be able to set this yourself Off has no inactivity suspension Suspend e Suspend Suspend Sets the form of suspension state If you choose Suspend you Mode e Save to Disk will suspend operation with power to system memory and everything else powered down or in a very low power state If To use Save to you choose Save to Disk your notebook will save all of system Disk automaticaly memory and the operating para
30. t will give you the opportunity to modify the settings of the setup utility as described in the following steps 1 When you turn on or restart the computer there is a beep and or the following message appears on the screen Error message please run SETUP program Press lt F1 gt key to continue lt F2 gt to run SETUP 2 Ifan error message is displayed on the screen and you want to continue with the boot process and start the operating system anyway press the F1 key Y Points e If your notebook emits a series of beeps that sounds like a code and the display is blank refer to the Trou bleshooting Section of your system User s Guide The Troubleshooting Section includes a list of error mes sages and their meanings e If your data security settings require it you may be asked for a password before the operating system will be loaded B Series BIOS 3 If an error message is displayed on the screen and you want to enter the setup utility press the F2 key 4 When the setup utility starts with a fault present the system displays the following message Warning Error message Continue 5 Press any key to enter the setup utility The system will then display the Main Menu with current parameters values po B Series Notebook BIOS MAIN MENU SETTING STANDARD SYSTEM PARAMETERS The Main Menu allows you to set or view the current the field s function and any special information
31. te Switch e Enabled book is in an active state The resume function can not be disabled as it works regardless of any other settings Lid Closure e Off On Enables and disables having closure of the Display panel put your Suspend e On notebook in Suspend mode Lid Open e Off Off Enables and disables having opening the Display panel acting as an Resume e On automatic resume Resume On LAN Off Off When this feature is set to On the system will wake when the inter e On nal LAN device receives a Magic Packet while in Suspend Mode This is not present if a wireless LAN is installed Serial Mouse e Disabled Disabled Enables and disables having activity on the serial port cause the sys Activity e Enabled tem to reactivate from inactivity timeouts Performance e Auto Fixed Enables and disables the ACPI Performance Control Control e Fixed Exiting from Power Menu When you have finished setting the boot parameters with the setup utility press the Esc key to go to the Exit the Power menu you can either exit from the setup menu If you wish to move to another menu use the utility or move to another menu If you wish to exit from cursor keys 29 po B Series Notebook BIOS BOOT MENU SELECTING THE OPERATING SYSTEM SOURCE The Boot Menu is used to select the order in which the BIOS searches sources for the operating system Follow the instructions for Navigating Through The Setup
32. the Re enter New Password field When a Supervisor Pass word is set it must be used to access the BIOS setup utility Set User Enter This field can only be accessed if the Supervisor Password is set Sets Password changes or cancels the User Password A User Password may be up to seven characters long and must include only letters or numbers no symbols Passwords are NOT case sensitive To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re enter New Password field When a User Password is set it must be used to access the setup utility Minimum User 0 Password Length Password on e Disabled Disabled When set to Disabled no password is required When set to First Boot Boot e First Boot password entry is required only before first boot When Every Boot is e Every Boot selected password is required every time the system is booted Boot from e All All When Supervisor Only is selected only the Supervisor can boot from Removable e Supervisor removable media Only the user who enters the Supervisor Password Media only before OS boot is treated as the Supervisor When All is selected boot ing from removable media is not restricted Floppy Disk e All All When Supervisor Only is selected only the Supervisor can access the Access e Supervisor floppy disk Only the user who enters the Supervisor Password before only OS boot is treated as a Supervisor Whe
33. tion Submenu of the PCI Configurations Submenu Menu r E Field Options Default Description IRQ 3 e Available Available Reserves IRQ 3 If Reserved is selected the BIOS reserves IRQ 3 for use by e Reserved legacy ISA devices and does not use it for embedded PCI or ISA devices IRQ 3 is removed from the IRQ bitmap in the PCI IRQ routing table IRQ 4 e Available Available Reserves IRQ 4 e Reserved IRQ 5 e Available Available Reserves IRQ 5 e Reserved IRQ 7 e Available Available Reserves IRQ 7 e Reserved IRQ 9 e Available Available Reserves IRQ 9 e Reserved IRQ 10 e Available Available Reserves IRQ 10 e Reserved IRQ 11 e Available Available Reserves IRQ 11 e Reserved IRQ 15 e Available Available Reserves IRQ 15 e Reserved 18 Advanced Menu CPU Features Submenu of the Advanced Menu The CPU Features submenu configures certain features of the CPU in the system PhoenixBIOS Setup Utility Advanced CPU Features Item Specific Help Intel R SpeedStep R Technology Auto CPU speed is changed based upon power source change Max Perf CPU speed is maximized Batt Opt CPU speed is optimized for battery operation Disabled CPU speed is fixed to the battery optimized speed Select Item Change Values Setup Defaults Select Menu Select gt Sub Menu Save and Exit Figure 10 CPU Features Submenu Table 10 Fields Options and Defaults fo
34. tup Utility Advanced Keyboard Mouse Features Item Specific Help lad Select power on state Hot Plug Enabled A Quick Point Manual Setting Disabled Pointing Device Configuration 1 Touch Panel Enabled Quick Point Enabled Disabled Fast External PS 2 Mouse Initialization on Resume Select Item Select Menu Change Values Select gt Sub Menu Setup Defaults Save and Exit Figure 5 Keyboard Mouse Features Submenu Table 5 Fields Options and Defaults for the Keyboard Mouse Features Submenu of the Advanced Menu Menu Field Options Default Description Numlock e Auto Auto Sets the NumLock function state when the computer e On completes booting e Off Hot Plug e Disabled Enabled Enables and disables the ability to plug a mouse or e Enabled keyboard into the PS 2 port and have it immediately recognized and active Quick Point e Disabled Disabled Enables and disables the ability to use Hot key to Manual Setting e Enabled enable or disable the Quick Point Touch Panel Quick Point External PS 2 Mouse Pointing Device e Configuration 1 e Configuration 2 e Configuration 3 e Configuration 4 Configuration 1 Selects pointing device configurations Configuration 1 Touch Panel Enabled Quick Point Enabled External PS 2 Mouse Disabled Configuration 2 Touch Panel Enabled Quick Point Disabled External PS 2 Mouse Enabled Configuration 3 Touch Pa
35. ty Event Log Validity View Event Log Event Logging System Boot Event Clear All Event Logs Mark Events as Read Space Available Valid Enter Press lt Enter gt key to view the contents of the event log Enabled Disabled INO Enter Select Item Select Menu Change Values Select gt Sub Menu Setup Defaults Save and Exit Figure 12 Event Logging Submenu Table 12 Fields Options and Defaults for the Event Logging Submenu of the Advanced Menu Menu Field Options Default Description Event Log Space Display only Capacity Available Event Log Validity Valid Display only View Event Log e Enter Enter Allows you to view content of event log Event Logging e Disabled Enabled Turns event logging on and off for all DMI events e Enabled System Boot Event e Disabled Disabled Turns event logging on and off for DMI system boot events e Enabled Clear All Event Logs e No No When set to Yes all event logs will be cleared at next boot e Yes Mark Events as Read e Enter Enter Allows you to select all events currently in the event log as read 21 po B Series Notebook BIOS SECURITY MENU SETTING THE SECURITY FEATURES The Security menu allows you to set up the data security features of your notebook to fit your operating needs and wy CAUTIONS to view the current data security configuration Follow the instructions for N
36. w the instructions for Navigating Through the Setup Utility to make any changes Points e In operating systems using ACPI Auto suspend Timeout Hard Disk Timeout and Video Timeout features are available exclusively through the operating system e When resuming from a Save to Disk suspension there will be a delay while the contents of system memory and operating parameters are loaded from the hard drive Y CAUTIONS e In Save to Disk mode there is no indication on the Status Indicator to let you know you are suspended rather than shut off from the power switch You may want to make a habit of always trying the Suspend Resume button before using the power switch e Resume on Modem ring when enabled will draw power from the bridge battery alone when your system is running off battery power This may poten tially drain your bridge battery Disabling Wake on Modem ring will prevent this from happening The following tables show the names of the menu fields for the Power menu and its submenus all of the options for each field the default settings and a description of the field s function and any special information needed to help understand the field s use PhoenixBIOS Setup Utility Main Advanced Power Savings Hard Disk Timeout off Display Timeout Off Standby Timeout Auto Suspend Timeout Suspend Mode Suspend Auto Save To Disk Off Resume On Modem Ring Off Resume On Time Off
Download Pdf Manuals
Related Search