Friedrich A 6 6 2 3 - 0 6 0 User's Manual
Contents
1. by young children without supervision 2 The plug should be accessible after installation of the appliance 3 The unit shall be installed in accordance with local and national codes lt 4 If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard 5 Please wait three minutes before restarting when the power is broken 6 Due to momentary high current demand when your air conditioner is started use a TIME DELAY fuse or a HACR type circuit breaker This symbol refers to a hazard or unsafe prac AU tice which can result in severe personal injury or death This symbol refers to a hazard or unsafe prac tice which can result in personal injury or prod uct or property damage em Table of Contents IDITOdU COD AA T EE EE 2 UNI IderitifiCalion ci 3 Control Panel Unit Operation 4 Remote Control Operation en i 5 Milli E M M 6 Hose and window Kit eere 7 Water Drainage Methods eene 8 M lntenance SEMI em 9 E AA 9 JPOUDIGSHOOU a 10 larga P 11 Introduction Portable Air Conditioner This Portable Air Conditioner is designed to provide a quick and easy cooling solution for areas that either do not have air conditionin2. kit has been designed to fit most stan dard vertical and horizontal window applications However it may be necessary for you to modify some aspects of the installation procedures for certain types of windows 1 Open window 2 Place window panel with extensions into window frame and adjust to width of window Window adapter kit may be installed vertically as well as horizontally This installaton may also be for crank style windows 3 Tighten the four screws on the window panel to secure the window panel extensions Close window 5 The window adapter kit should now fit securely within the window frame and you can now attach the air ex change tubes If you are having trouble attaching the air exchange tubes you may attach the tubes prior to install ing the window adapter kit Attaching the air exchange tubes to the air conditioner Note While it is possible to operate the unit in COOL MODE with only the exhaust hose connected for optimum cooling performance it is recommended to operate the unit with both the intake and exhaust hoses connected This will provide the best cooling performance without drawing outside air into the space In HEAT MODE the unit will operate down to an outdoor temperature of 14 F It is recommended that only one hose be used for optimal performance The intake opening on the window kit should be covered with the cover that is supplied with the unit There may be a slight negative pressure creat
3. HSA IEUIEURETAE FRIEDRICH Installation amp Operation Manual ZoneAire Portable Air Conditioner Models PO9B P128 Portable Air Conditioner with Heat E FRIEDRICH Friedrich Ale Condititalag Ce 10001 Recni Place Sahte 500 gt San Astonia Texas 78216 800 541 6645 DAA SERE ppm DAA ppm 40 100 lt 500 100 lt 100 GERREN 1 E RE 2 LIA TURN PO9B P12B Ee Ep H T AE Friedrich seque nmm RX11090006 Name SA BH mma a ur 11 09 15 Ninha A6623 060 Dade 11 10 07 Version 1 0 PEE EW lg BRAS E ts Y d FRIEDRICH Installation amp Operation Manual ZoneAire Portable Air Conditioner Models PO9B P12B Portable Air Conditioner with Heat Model PH14B Heat Pump Foreword Thank you for purchasing the new Friedrich ZoneAiree Por table Air Conditioner We are confident that you will find this unit a quiet and efficient example of Friedrich reliability This Installation and Operation Manual has been designed to insure maximum satisfaction in the performance of your unit For years of trouble free service please follow these installa tion instructions closely Notice 1 This appliance is not intended for use
4. ay be set by pressing the TEMP A or TEMP Y button 3 Is initiated only when the room temperature is below 77 F 4 Press FAN SPEED button to choose between high medium or low speeds Fan Operation To set the time to stop the machine with the unit running 1 Press MODE button to choose the fan mode LED will press TIMER button the LED window will show G orr con shine yellow tinually press the TIMER button set the preferred time to stop 2 Air will be circulated throughout the room without cooling the machine The setting range is 1 24 hours 3 Press FAN SPEED button to choose between high medium NOTE During timer mode if the TIMER button is pressed and low speeds again it will cancel the timer operation NOTE The set temperature must be lower than room i i temperature for the fan to operate Warning Light Condensed water may accumulate in the unit If the internal Time Set Function tank becomes full the Warning Light will come on and the unit To set the time to start the machine with the unit off but power will not operate until the unit has been drained supplied press TIMER button the LED window will show G on continually press the TIMER button set the preferred start time The setting range is 1 24 hours Remote Control Identification and Function Time Temperature Set Control Used for adjusting the timer and te
5. blinds furniture etc The filter is dirty or obstructed Clean the filter See Maintenance Service or remove Unit Does Not Cool Heat obstruction Room Sufficiently There is excessive heat or moisture Be sure to use exhaust vents while cooking or bathing cooking showers etc in the room and if possible try not to use heat producing appliances The exhaust hose is bent during the hottest part of the day LE In case of major malfunction disconnect power immediately and call for service FRIEDRICH 1883 Friedrich Air Conditioning Company 10001 Reunion Place Suite 500 San Antonio TX 78216 PORTABLE AIR CONDITIONERS LIMITED WARRANTY FIRST YEAR ANY PART If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from date of original purchase FRIEDRICH will repair the product at no charge provided the product is transported to a Friedrich Authorized Service Center for repair ALL transportation charges are the sole responsibility of the owner This remedy is expressly agreed to be the exclusive remedy within twelve months from the date of the original purchase SECOND THROUGH FIFTH YEAR SEALED REFRIGERANT SYSTEM If the Sealed Refrigeration System defined for this purpose as the compressor condenser coil evaporator coil reversing valve check valve capillary filter d
6. e for system air transfer Window panel extensions Extends window panel to fit windows of various dimensions Tube adapters Connect Air exchange tubes to window panel Screws 12 screws are included for assembling the window adapter kit Some screws may be partially assembled onto window panel Air exchange tubes Exchanges air between the unit and outdoors Tube Covers Covers the intake air outlet during heating mode WN Drain Hose Empty condensation from unit continuously Drain Key Quick connector for Built In Drain Minimum window extension 26 Maximum hose extension 60 Drain Hose amp Drain Key PH14B model only Instructions for assembling the window adapter kit Back of 1 Insert tube adapters through the back of the window panel window panel 2 Secure each tube adapter with four screws through the front of the window panel 3 Insert window panel extensions into window panel Lightly tighten the screws in the window panel to hold the extensions in place Tube Adapters Window Panel Window Panel Extension scre Extension a Window SS Installing the window adapter kit Important Do not over stretch the exhaust tube or Note The window adapter kit must be install d and con Ke any unnecessary bends In it nected for the air conditioner to work properly in Cool mode The window adapter kit is not required when using the unit in Dehumidify or Fan modes Your window adapter
7. ed in the space while the unit is operated in the single hose configuration Cool Mode 1 Attach the ends of both tubes to the window adapter kit 2 Attach the other end of both tubes to the air conditioner Heat Mode 1 Attach one tube to the window adapter kit 2 Attach the other end of tube to the exhaust air outlet of air conditioner 3 Place the included cover on the intake air outlet of air conditioner To attach air exchange tubes push tube onto tube adapter and twist until the tab is in place in the hole on the tube To remove air exchange tubes twist the end until the tab is clear of the hole in the tube and pulls off Do not attach the tubes if using the unit in dehumidify mode Maintain a clear distance from walls furniture etc of at least 10 inches around the unit to allow proper air circulation and prevent damage to the unit gt Condensation Handling Cooling Mode Your ZoneAires Portable Air Conditioner is designed to evapo rate the condensation removed from the interior space through the exhaust hose Under certain conditions it is possible that the unit will not evaporate 100 of the removed moisture The unit is designed with a built in reservoir to accumulate excess condensate and help dispose of it Heating Mode In heating mode it is possible to still collect condensate in the unit Because the evaporatio
8. g or areas that the current system cannot maintain at a comfortable level This unit is also great as a back up system in case the primary cooling system should fail Other means of conditioning should be employed when the indoor temperature is either below 17 C 63 F or above 35 C 95 F Attention Before you use your PORTABLE AIR CONDITIONER please read this instruction manual carefully so that you get the best performance from the unit This instruction manual is used for guidance and does not form part of a contract We reserve the right to make technical changes without prior notice E ac oT ES 3823 9 o 23 o o 2 2 cU Q 235 7 90 S E e5555 e L 3 7m OwX0 3 0 40 0 LY bz3o 2z 555 c O coo r szo205235 8 42t orlrloaxaxacx u m o NO 4 NON oo Unit Identification and Function Control Panel Operation Cool High r3 Dehumidify Mead Water Full Heat ET Fan Only a 000 ON OFF Mode Fan Speed ZoneAire Room Temp Set Temp Timer On Off Timer Adjust Temp Timer Cooling Heating and Dehumidifying Operation The operating range for cooling operation is 61 F 89 F the operating range for heating is 61 F 80 F the operating range for dehumidifying is 68 F 88 F Power source The AC socket must be firm and reliable Don t connect the portable air co
9. ilter clean 4 Rinse the filter and dry it thoroughly in a shaded place 5 Install the air filter back to its original place Cleaning the air conditioner Clean the surface of the unit with a damp cloth then dry with a clean towel or cloth A Do not use chemical solvent like benzene or alcohol to clean the surface of the unit If you do so the surface may be scratched damaged or even cause the case to become damaged Prior to operating seasons 1 Check to ensure that the air inlets and outlets of the unit are not blocked 2 Make sure that air filter is properly in place before operat ing the machine If the machine is operated with air filter removed dust and foreign objects will result in faulty per formance of the air conditioner Preparation for storage 1 Turn off the air conditioner disconnect the power 2 Perform proper maintenance to the air filter and other parts 3 Pull out the drain plug to drain out all of the water from the base Operating the unit in fan only mode for 12 hours will help ensure there is no moisture within the unit Drain valve 4 Cover the unit to prevent dust or debris from entering the unit nn Safety Precautions Install in an accessible location Only operate the unit in an upright position Do not place in direct sunlight to avoid discoloration of the plastic Do not use the unit on or in water to avoid electrical shock Do not use nea
10. mp PH14B model only The condensate produced in heating mode can also be drained through the supplied drain hose utilizing the internal built in drain pump Follow the steps below for proper operation of the pump NOTE The built in drain pump operation is only activated in heating mode Installation STEP 1 Connect the supplied drain hose to the drain key STEP 2 Connect the drain key and hose to the drain outlet located on the rear panel STEP 3 Lead the other end of drain hose to a suitable location for drainage like a drain or sink or the outlet located on the window panel kit Use caution when using the drainage outlet on window panel kit to avoid creating a slipping hazard Dismantle STEP 1 Press the release button on the unit rear panel STEP 2 Pull out the drain key and hose STEP 3 Store the drain hose for next time usage uM l Maintenance Service AR Electrical Shock Hazard Disconnect all power before servicing or cleaning Failure to follow these instructions can result in death electrical shock or fire Cleaning the air filter If the air filter is clogged with dust the air flow will be reduced Clean the filter once every two weeks Open and clean the air filter 1 Pull the filter out as shown in the drawing 2 Take out the air filter from the filter cover 3 Wash the air filter by immersing it gently into warm about 40 C or 104 F water with a mild detergent or vacuum the f
11. mperature The default display on control panel is room temperature When the 7 or the button is pressed in cool mode the set temperature is displayed and may be adjusted After 15 seconds the display will revert back to room temperature Timer setting is available from 1 24 hours by pressing the button on Fan Speed Control OW d 7 Mode Control SO O Se C Y a Y S amp HIGH 56 MED LOW i geN J Press this button to change the operation we mode in the order of Farenheit Celsius Control x F C Cool Dry Fan Heat Press this button to change back Mad and forth from Farenheit to Timer control Celsius temperature readings Y d rriepricn In running mode Auto switch off In standby mode Auto switch on Press the 7 or the 2 button to adjust the time setting for 1 hour interval H H ADD Drawing of the following Cover Drain Hose and Drain Window installation dd y p Window adapter kit Window Pane extensions An installation parts kit is packed with your unit in a separate carton Before you discard the packaging that your unit came Window panel in please locate the carton that contains these parts and ensure that all parts are present Window panel Attaches to window opening to allow air exchang
12. n process does not work as efficiently in colder temperatures it may be necessary to drain the water from the unit as described ALL MODELS in the Draining Water or Permanent Drainage section or using the supplied Built In Drain Pump and hose Internal Water Level 1 Under any mode if the water level is in the low area the unit will function normally 2 If the water level is in the normal area the unit will con tinue to function normally while internally evaporating the condensate 3 If the unit cannot evaporate all of the condensate internally the tank may become full If the tank becomes full the unit will turn off and the Water Full light will illuminate Draining Water The water can be drained from the unit by removing the drain plug and letting the water drain by gravity 1 When the WATER FULL lamp is on unplug the unit and move the unit to a suitable location for draining the condensation 2 Using the gravity drain method ensure that the drain plug is located above a suitable area for draining the condensate and remove the plug Re install the plug once all water has drained 3 Return the unit to the original location and restore power and duct connections 4 The WATER FULL indicator should be off and the unit will return to normal operating mode Permanent Drainage For permanent and continuous drainage a 1 2 hose may be attached to the unit and led down a drain ZA Valve Built in Drain Pu
13. nditioner to a multiple socket outlet which is also being used for other electrical appliances Insert the AC power plug securely into the AC socket before using the unit when it beeps after two seconds press ON OFF button the unit begins to run LCDI power cord information All Friedrich portable air conditioners are shipped from the factory with a Leakage Current Detection Interrupter LCDI equipped power cord The LCDI device meets the UL and NEC requirements for cord connected air conditioners effec tive August 2004 To test your power supply cord 1 Plug power supply cord into a grounded 3 prong outlet 2 Press RESET See drawing below 3 Press TEST listen for click Reset button trips and pops out 4 Press and release RESET listen for click Reset button latches and remains on The power supply cord is ready for operation NOTE LCDI device is not intended to be used as a switch Once plugged in the unit will operate normally without the need to reset the LCDI device If the device fails to trip when tested or if the power supply cord is damaged it must be replaced with a new supply cord from the manufacturer We recommend you contact our Tech nical Assistance Line at 800 541 6645 ext 261 To expedite service please have your model and serial number available WARNING NEVER CUT OR REMOVE THE GROUNDING PRONG FROM PLUG NEVER USE EXTENSION CORDS TO OPERATE AN AIR CONDITIONER Reset Button M
14. ode control Portable Air Conditioner The mode control has three setting Cool Dehumidify and Fan The settings are adjusted with the Mode Control button A light will indicate which setting is currently being used Mode control Portable Air Conditioner with Heat The mode control has four settings Cool Dehumidify Heat and Fan The settings are adjusted with the Mode Control button A light will indicate which setting is currently being used Peu operation Press MODE button to choose the cooling mode LED will shine green During the cooling operation always place the air exhaust hose through an open window 2 Desired room temperature may be set by pressing the TEMP A or TEMP Y button 3 Press FAN SPEED button to choose between high medium and low speeds NOTE In order to improve the cooling efficiency 8 If your room is directly exposed to the sun draw the curtains b Do not place near other heat source Dehumidifying Operation 1 Keep the windows and the doors closed to aid in effectively dehumidifying the room 2 Press MODE button to choose the dehumidifying mode LED will shine orange the fan speed cannot be adjusted When used as dehumidifier only it is not necessary to install the exhaust hose MN operation Press MODE button to choose the heating mode LED will shine red During the heating operation always place the air exhaust hose througn an open window 2 Desired room temperature m
15. r gas appliances flammable liquids or fires Power Sources Hm Make sure your electrical receptacle has the same configuration as your air conditioner s plug If different consult a Licensed Electrician Do not use plug adapters Do not use an extension cord Do not remove ground prong Always plug into a grounded 3 prong outlet Failure to follow these instructions can result in death fire or electrical shock Other Warnings Do always keep the unit 3 feet away from TV sets or radios to avoid the risk of electromagnetic interference Do always keep the air outlets free from obstructions Troubleshooting Before seeking repair or service please check the following first COMPLAINT CAUSE SOLUTION The unit is turned off The LCDI power cord is unplugged Plug into a properly grounded 3 prong receptacle The LCDI power cord has tripped Reset Press and release RESET listen for click Reset button button has popped out latches and remains in to resume operation Unit does not operate The circuit breaker has tripped or the Reset the circuit breaker or replace the fuse as supply circuit fuse has blown applicable If the problem continues contact a licensed electrician There has been a local power failure The unit will resume normal operation once power has been restored The intake exhaust hoses are blocked Ensure that the return and or discharge air paths are not blocked by curtains
16. restraints strikes material shortages beyond the control of FRIEDRICH or acts of God OBTAINING WARRANTY PERFORMANCE Service will be provided by the FRIEDRICH Authorized Dealer or Service Organization in your area They are listed in the Yellow Pages If assistance is required in obtaining warranty performance write to Room Air Conditioner Service Manager Friedrich Air Conditioning Co P O Box 1540 San Antonio TX 78295 1540 LIMITATIONS THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES Anything in the warranty notwithstanding ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND OR MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY NOTE Some states do not allow limitations on how long an implied warranty lasts or do not allow the limitation or exclusion of consequential or incidental damages so the foregoing exclusions and limitations may not apply to you OTHER This warranty gives you specific legal rights and you may also have other rights which vary from state to state PROOF OF PURCHASE Owner must provide proof of purchase in order to receive any warranty related services All service calls for explaining the operation of this product will be the sole responsibility of the consumer All warranty service must be provided by an Authorized FRIEDRICH Se
17. rier and all interconnecting tubing supplied by FRIEDRICH in your Room Air Conditioner fails because of a defect in workmanship or material within sixty months from date of purchase FRIEDRICH will pay a labor allowance and parts necessary to repair the Sealed Refrigeration System PROVIDED FRIEDRICH will not pay the cost of diagnosis of the problem removal freight charges and transportation of the air conditioner to and from the Service Agency and the reinstallation charges associated with repair of the Sealed Refrigeration System All such cost will be the Sole responsibility of the owner This remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase APPLICABILITY AND LIMITATIONS This warranty is applicable only to units retained within the Fifty States of the U S A District of Columbia and Canada This warranty is not applicable to 1 Air filters or fuses 2 Products on which the model and serial numbers have been removed 3 Products which have defects or damage which results from improper installation wiring electrical current characteristics or maintenance or caused by accident misuse or abuse fire flood alterations and or misapplication of the product and or units installed in a corrosive atmosphere default or delay in performance caused by war government restrictions or
18. rvice Agency unless authorized by FRIEDRICH prior to repairs being made 11 M FRiEpRich Friedrich Air Conditioning Co 10001 Reunion Place Suite 500 San Antonio Texas 78216 800 541 6645 www friedrich com
Download Pdf Manuals
Related Search