Fisher-Price OCEAN WONDERSTM AQUARIUM CRADLE SWING 79667 User's Manual
Contents
1. Swing Cradle Seat moves front to back Seat moves side to side Model Number 79667 Please read these instructions before use of this swing Keep this instruction sheet for future reference as it contains important information Adult assembly is required Tool needed for assembly Phillips screwdriver not included Requires four D LR20 alkaline batteries for operation not included Maximum Weight Limit 24 Ibs 10 9 kg IMPORTANT If your child weighs less than 24 Ibs but is really active and appears to be able to climb out of the swing immediately discontinue its use Product features and decorations may be e e Fisher Price different than shown in photos above Warnings and Caution A WARNING e To prevent serious injury or death from falls and being strangled in the restraint system Always use restraint system Never rely on the tray to restrain child Never use with an active child who may be able to climb out of the seat e Never leave child unattended A CAUTION This product contains small parts in its unassembled state Adult assembly is required Consumer Information Occasionally a consumer may experience a problem with one of our products If this should happen please call us toll free rather than return this product to the store Usually we can solve the problem over the telephone or send you replacement parts Please call Fisher Price Consumer Relations toll f2. Music and Sounds Off To select a comfortable listening setting turn the volume dial Oe e o o4 Hint The waterglobe mobile music or sounds will turn off after approximately seven minutes To restart waterglobe mobile music or sounds press the reset button for another seven minutes of use Problems and Solutions Problem Motor is not running no swinging Motor is running but swinging stops after a few minutes No difference noticed in swinging motion after power dial is adjusted Swinging motion too high even at the lowest setting Waterglobe lights mobile music sounds do not work and swing is off Music sounds do not work and power dial is set to Waterglobe lights does not work and power dial is set to Mobile does not work and power dial is set to Care Probable Cause Power is not on Batteries incorrectly installed Dead batteries Need to start swinging motion Swing motion setting is inappropriate for child s weight Weak batteries Swing did not have sufficient time to adjust to different setting Weak batteries Normal operation Power dial is not on correct setting Dead batteries Waterglobe lights mobile music sounds turn off automatically after seven minutes Music sounds switch is in OFF O position Music sounds turn off automatically after seven minutes Mobile waterglobework switch is in OFF O position or mobile only position Waterglobe l
3. attery Compartment Door Battery Compartment e Using a coin press the tab on the battery compartment door and remove it e Insert four D LR20 alkaline batteries as indicated inside the battery compartment Hint We recommend using alkaline batteries for longer battery life e Replace the battery compartment door Hint If the swinging motion becomes noticeably slower or sounds and lights become faint or stop remove the batteries and replace them with four new D LR20 alkaline batteries Dispose of exhausted batteries properly Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your product To avoid battery leakage Do not mix old and new batteries or batteries of different types alkaline standard carbon zinc or rechargeable nickel cadmium Insert batteries as indicated inside the battery compartment e Remove batteries during long periods of non use Always remove exhausted batteries from the product Dispose of batteries safely Do not dispose of batteries in a fire The batteries may explode or leak e Never short circuit the battery terminals e Use only batteries of the same or equivalent type as recommended Do not charge non rechargeable batteries Remove rechargeable batteries from the product before charging If removeable rechargeable batteries are used they are only to be charged under adult supervision er Swi
4. be lights switch to desired setting Press the reset button to restart mobile waterglobe lights for another seven minutes e Remove the tray from the seat e Unbuckle the restraint system e Remove the pad elastic loops from the pegs and unfasten the pad fasteners from the seat e Remove the pad from the restraint system e Remove the toys from the mobile e Machine wash the pad and toys in cold water with a mild detergent Do not use bleach Tumble dry on low heat and remove promptly To clean the seat restraint system tray mobile storage pouch and motorized frame use a mild cleaning agent and damp cloth Rinse with clean water to remove residue e Replace the pad onto the seat Replace the toys on the mobile Periodically check the swing for loose fasteners or broken parts and tighten as needed Fisher Price Inc a subsidiary of Mattel Inc East Aurora NY 14052 U S A 2003 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Printed in China 79667 pr 0921
5. e assembly upright Insert the two elastic loops on the pad Pull the legs out so that the buttons snap into the holes in through the holes in the seat bottom the motorized frame If the buttons do not snap into the holes you probably have not assembled the storage pouch e While holding the elastic loops in place turn the seat face down correctly Please refer back to assembly steps 3 and 4 s 7 e Hook the elastic loop on the left side onto the peg on the e When standing behind the product all four feet should be right side flat upon the floor And check for an L marking on the left 3 Wes ieee redira h foot and an R marking on the right foot ee elastic loop on the right side onto the peg on the If the feet are not flat upon the floor or the left and right feet have been reversed remove both lower legs from the upper Hint The elastic loops should cross over each other when legs Replace them onto the opposite upper leg 5 attached correctly to the pegs Assembly Insert the tray tabs into the slots in each side of the seat e Fold the top of the pad down Insert the waist belts through the slots in the pad Make sure the waist belts are not twisted Seat Tube Arm Hole 1 2 Seat Tube Button e While pressing the button on the seat tube slide the seat tube arm onto the seat tube Make sure the button on the seat tube snaps into the hole in the seat tube arm e Turn the seat up
6. he dealer or an experienced radio TV technician for help Note Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment Parts Motorized Frame Note Please remove tape that was added for packaging purposes Storage Pouch Pad with Headrest Seat Tube Arm 2 Upper Legs Seat with Restraint System gt 2 Feet 2 Lower Legs 8 x 2 Screw 2 S ae A M5 x 30 mm Bolt 2 H M5 Lock Nut 2 ALL SHOWN ACTUAL SIZE Assembly IMPORTANT Before each use or assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts Button Button 8 x 2 Screw 2 Hole Up Hole Up 4 SHOWN ACTUAL SIZE y Storage Pouch Pockets Lower Leg Foot e Position a lower leg so that it stands on a flat surface as shown Fit a foot onto the end of the lower leg W e Insert a 8 x 2 screw through the bottom of the foot and into the lower leg Tighten the screw with a Phillips screwdriver Do not over tighten e Repeat this procedure to assemble the other foot to the other lower leg 3 e Position the storage pouch with the pockets toward you and the button holes are up e Position the legs so that the feet are away from yo
7. ights mobile turn off automatically after seven minutes Mobile waterglobe lights switch is in OFF O position or waterglobe only position Mobile waterglobe lights turn off automatically after seven minutes Solution Turn the power dial to one of six settings Remove the batteries and replace in correct orientation as indicated inside the battery compartment Replace all four batteries with four fresh D alkaline batteries To start swinging motion give the seat a light push Adjust the power dial to a higher speed setting and give the seat a light push Replace all four batteries with four fresh D alkaline batteries Allow the swing time to adjust to new setting Replace all four batteries with four fresh D alkaline batteries To slow swinging place one end of a blanket underneath your child and let the other end of the blanket drape down while swinging Position the power dial to the position Replace all four batteries with four fresh D alkaline batteries Press the reset button to restart waterglobe lights mobile music sounds for another seven minutes Slide music sounds switch to desired setting dar Press the reset button to restart music sounds for another seven minutes W Slide mobile waterglobe lights switch to desired setting F Press the reset button 2 to restart waterglobe lights mobile for another seven minutes 9 oO Slide mobile waterglo
8. ng Waterglobe and Mobile Use IMPORTANT Before each use or assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts To Unfold Button Button Leg fezonao t 3 4 nf ocean Ope nn qn nnn eng ree I Firmly pull the legs outward Make sure the buttons snap into the notches in the motorized frame e Check to be sure the legs are locked into position by pushing the legs inward The legs should not move A WARNING e To prevent serious injury or death from falls and being strangled in the restraint system Always use restraint system Never rely on the tray to restrain child Never use with an active child who may be able to climb out of the seat e Never leave child unattended Restraint Belts Waist Belt e Place your child in the seat e Pull the crotch belt up between your child s legs and fasten both waist belts to the crotch belt Make sure you hear a click on both sides Anchored End Buckle Free End To Tighten To Loosen is To tighten the waist belts Feed the anchored end of the waist belt up through the buckle to form a loop Pull the free end of the waist belt To loosen the waist belts Feed the free end of the waist belt up thro
9. r replaced item to you This warranty is void if the owner repairs or modifies the product This warranty excludes any other liability other than that express ly stated above including but not limited to any incidental or consequential damages SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO STATE FCC Note United States Only Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Consult t
10. ree at 1 800 432 5437 8 AM 6 PM EST Monday through Friday Hearing impaired consumers using TTY TDD equipment please call 1 800 382 7470 Or write to Fisher Price Consumer Relations 636 Girard Avenue East Aurora New York 14052 For countries outside the United States CANADA Questions 1 800 567 7724 Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario L5R 3W2 GREAT BRITAIN Mattel UK Ltd Vanwall Business Park Maidenhead SL6 4UB Helpline 01628 500302 AUSTRALIA Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 NEW ZEALAND 16 18 William Pickering Drive Albany 1331 Auckland ASIA Mattel East Asia Ltd Room 1106 South Tower World Finance Centre Harbour City Tsimshatsui HK China One 1 Year Limited Warranty Fisher Price Inc 636 Girard Avenue East Aurora New York 14052 warrants that the Ocean Wonders Aquarium Cradle Swing is free from all defects in material and workmanship when used under normal conditions for a period of one 1 year from the date of purchase Should the product fail to perform properly we will repair or replace it at our option free of charge Purchaser is responsible for shipping the product to Fisher Price Consumer Relations at the address indicated above and for all associated freight and insurance cost Fisher Price Inc will bear the cost of shipping the repaired o
11. right Fit the pad edges around the rim of the seat e Hook the two fastener straps on each side of the pad onto the rim on each side of the seat Assembly AA M5 x 30 mm Bolt _ Rounded Side M5 Lock Nut W BOTH SHOWN ACTUAL SIZE d 13 M5 x 30 mm Screw e Fit an M5 lock nut into the recess in the seat tube Make sure the rounded side of the lock nut faces out e Insert an M5 x 30 mm screw into the opposite side of the seat tube Tighten the screw with a Phillips screwdriver Do not over tighten Rounded Side a e Fit an M5 lock nut M5 Lock Nut into the recess inthe BOTH SHOWN ACTUAL SIZE motorized frame tube v g Make sure the rounded side of the lock nut faces out Insert an M5 x 30 mm screw into the smaller hole in the motorized frame tube Tighten the screw with a Phillips screwdriver Do not over tighten Motorized Frame Tube Hole Seat Tube Button f m Tort TN Fit the string below the knot of a toy e Press the button on the seat tube and slide the seat tube into the motorized frame tube Make sure the button on the seat tube snaps into the larger hole in the motorized frame tube through the slot in a clip on the mobile Pull down on the toy to be sure it is secure on the mobile e Repeat this procedure to assemble the other three toys to 7 the mobile Battery Installation 1 5V x4 D LR20 SHOWN ACTUAL SIZE B
12. u Red Dot Up Slide the storage pouch onto the upper legs Upper Leg Straight End Rivet Butt he Through Button Button Hole Hole Hole Lower Leg e Position an upper leg so that the red dot is up e While pressing the button on the straight end of an upper leg insert the upper leg Lee eel leg HELE sure the Dut Fit the rivets on the upper legs through the button holes in ton on the upper leg snaps into the hole in the lower leg 7 top ends of the storage pouch e Repeat this procedure to assemble the other upper leg to the other lower leg Assembly Motorized Frame Seat e Locate the R and L on the underside of each elbow foot The L J R indicates the right leg The L indicates the left leg e While pressing the upper button on the right leg fit it into the tube in the motorized frame Make sure the upper button PI h h on the right leg snaps into the hole in the tube oes t 7 pad onto the seat with the ruffle toward the top e Repeat this procedure to assemble the left leg to the ae Fold the bottom of the pad up Insert the crotch belt through motorized frame the slot in the pad Make sure the crotch belt is not twisted e Position the seat upright e When the legs are assembled correctly to the tubes in the motorized frame you should not see the red dots Storage Pouch Pockets e Fold the top of the pad down Stand th
13. ugh the buckle to form a loop Q Enlarge the loop by pulling on the end of the loop toward the buckle Pull the anchored end of the waist belt to shorten the free end of the waist belt O Note Check to be sure the restraint is securely attached by pulling it away from your child Swing Waterglobe and Mobile Use Adjust Swing Motions Seat Tube Button Swing You can adjust the motion of the swing side to side or front to back e Press the seat tube button to unlock the seat tube e Rotate the seat tube to the desired position Adjust Seat to Recline or Upright Front Edge of Seat You can adjust the seat to two different positions Recline or Upright e From behind the seat press both seat position buttons e Push the seatback up until the buttons snap into the upright position e Push the seatback down until the buttons snap into the recline position 10 Using the Tray Fit the tabs on the tray into the slots in the sides of the seat To remove the tray pull one edge of the tray out and lift Storage Button Button a on ay r Set wees Sand prosz e Press the buttons on the back of the motorized frame while pushing the legs inward Lean the swing frame against a wall for storage IMPORTANT Remove the batteries for long term storage Hint The legs may be disassembled for long term storage Press the button on each lower leg and remove them from the
14. upper legs Swing Waterglobe and Mobile Use Swing Turn the power dial to the ON position The swing begins swinging Ries e Select any of six speed settings re Be sure to turn swinging OFF O when not in use Hints As with most battery powered swings a heavier child will reduce the amount of swinging motion on all settings In most cases the low setting works best for a smaller child while the high set ting works best for a larger child If the low setting provides too much swinging motion for your child try placing one end of a blanket underneath your child and let the other end of the blanket drape down while swinging Waterglobe Mobile Music and Sounds Turn the power dial to to turn power ON for waterglobe mobile music and sounds Hint The swing does not work on this power dial setting If you like to use the waterglobe mobile music or sounds and swing at the same time turn the power dial to any of the six speed settings 11 Swing Waterglobe Mobile ON Power Dial Waterglobe Mobile ON Reset Button Osmi dee o o o 4 of ox Music Sounds Switch Mobile Waterglobe Volume Switch Dial Control Panel To select waterglobe mobile slide switch to Mobile Lights Waterglobe Mobile and Lights Waterglobe O Mobile and Lights Off Waterglobe To select sounds or music slide switch to Music ree Naves a Rain Babbling brook O
Download Pdf Manuals
Related Search