Fisher & Paykel CG602 User's Manual
Contents
1. Fisher amp Paykel Installation Instructions NZ amp AU CG602 SERIES 99 99869 CG913 SERIES 599257 A 01 2005 NZ amp AU Safety amp Warnings A WARNING Cut Hazard Beware of sharp edges when handling stainless steel appliances Failure to use caution could result in injury or cuts A WARNINGS Particular attention shall be given to the relevant requirements regarding ventilation This product should not be sealed into the bench with silicone or glue Doing so will make future servicing difficult Fisher amp Paykel will not be liable for costs associated with releasing such a product nor for repairing damage that may be incurred in doing this When this product is installed it shall not be used as a space heater especially if installed in boats or caravans No combustible material or products should be placed on this product at any time Do not spray aerosols in the vicinity of this product while it is in operation A CAUTION This product must be installed according to these installation instructions and must comply with local building regulations local gas authority codes and electrical regulations Failure to install the product correctly could invalidate any warranty or liability claims IMPORTANT Read these instructions carefully before installi2. PO Box 798 Cleveland OLD 4163 Toll Free 1300 650 590 Tel 07 3826 9100 Fax 07 3826 9298 Email customer careafp com au
3. for dimensions sion and d rds he They have Testing Lab These products meet the Standa reguirements when installed to dimensions in these Instructions been tested by an Independent Clamping Down the Cooktop This cooktop is supplied with fastening clamps that will cope with a bench thickness of 20 50 mm For benchtops thicker than 50 mm recess the underside to a thickness of 20 50 mm recessed to 50mm ee CG602 CG902 series CG913 series Gas Supply Con nection This cooktop is supplied set up for Natural Gas but is suitable for installation with either atural Gas or LPG Refer to relevant table for pressures and appropriate orifice sizes Gas connecti the elbow su on to the product MUST use pplied The regulator will not seal if installed without it Ensure the blue wash er supplied is located between the elbow supplied and product inlet as below Failure to use this washer will cause the product to leak Tighten the floating nut to firm finger tight plus an additional 1 4 turn 909 Blue washer Elbow 1 2 BSP male Gas Inlet 1 2 BSP internal thread After installation make sure all connections are gas tight A duplicate data plate enclosed inside the accessories pack should be placed on an accessible surface ad Flexible Hoses Flexible hose assemb 1869 Class B or Class Flexible hoses should jac
4. ance below benchtop to 45 mm 45 mm 81 mm F amp P DishDrawer or F amp P oven f Ensure there is an earthed power outlet within 900 mm of the rear right hand corner of the product When used with af exible hose the connector on the wall should be between 800 mm to 850 mm above the floor and in the region outside the width of the appliance to a distance of 250 mm This should be accessible with the appliance installed g When protecting a wall with non combustible material it must be at least 150 mm high Installation Instructions Standards Reguirements Australian and New Zealand Gas Installation Standards AS5601 NZS 5261 reguire a cooktop to be installed so that the surface temperature of any nearby combustible surface will not exceed 65 C above ambient Typically this is achieved by A Having the wa Dimen OR B by protecting the wall to at least 150 mm high Dimension g along it s length with non combustible surface materials such as 5 mm thick ceramic tiles alone are adeguate Tempered glass or sheetmetal min 0 4 mm thick is acceptable when used in front of a fire resistant material Fisher amp Paykel Splashback not available in Australia This is stainless steel with a 10 mm air gap to the wall When used with a 10 mm gap behind the product to the front of the splashback Only with SB90 series and SB1216 splashbacks the cooktop spaced away from see Clearances
5. bbles will indicate a leak Tighten the fitting and recheck for leaks Ensure the washer supplied is located between elbow and product gas inlet urn burn on each gas valve and er ight each Check for a clear blue flame without yellow tipping If burners show any abnormalities check that they are located and assembled properly Check correct orifices are installed CG913TM only O 1 uk WN The operation of the appliance including the ignition system must be tested before installation is complete If after following the instructions given satisfactory performance cannot be obtained contact the local gas authority or your local Approved Service Agent for advice and assistance Conversion to Different Gas Type Burners can be used with NG or LPG provided that the orifices appropriate for the gas supply are installed To change the orifices you will need a 7 mm box spanner and a 10 mm ring spanner for CG913TM Turn off ml main electrical supply AW WARNING Tr Shock Hazard Disconnect product from main power supply before continuing Ensure all gas valves are turned off Remove all trivets and burner heads Pull off knobs Unscrew the orifices and replace them with the correct ones size numbers are stamped on the side eg 70 0 70 mm see figure 1 Remove the 2 screws holding each burner 3 on the wok burner Lift hob tray from the product A X WARNING Cu
6. chtop Dimensions manifold F J centre line D Product CG602 series CG902 series CG913 series A Width 578 914 914 B Depth 511 533 546 C Height 40 40 76 Pan support to Benchtop 43 52 Wok 43 52 Wok 22 Cutout CG602 series CG902 series CG913 series D Width 560 558 562 870 846 872 870 860 882 E Depth 490 485 495 494 478 501 494 486 524 F Radius R10 R10 R10 G 30 30 30 H 40 50 35 J Clearance to nearest 60 60 81 combustible service Note All measurements given in millimetres mm Cutout dimensions are given as an ideal measurement e g for new cutouts followed by an otherwise acceptable range in brackets e g for existing cutouts or replacement products Clearances a 600 mm minimum from top of trivet to rangehood 750 mm minimum from top of trivet to overhead exhaust fan Fisher amp Paykel splashbacks are 750 mm high b 600 mm minimum from top of trivet to downward facing combustable surface 450 mm minimum if protected by tiles or fire resistant materials CG602 SERIES CG902 SERIES CG913 SERIES Clearance from side edge of 130 mm 120 mm 80 mm product to any combustible surface d Clearance from rear edge of 100 mm 90 mm 90 mm product to any combustible surface Clearance from rear edge of 10 mm 10 mm 10 mm product to any non combustible surface e Clearance below benchtop to any 60 mm 60 mm 81 mm combustible surface Clear
7. ent to the cooktop ies should be AS NZS D certified not be exposed to temperatures exceed ing their certified value They should not touch hot surfaces on the cooktop or neighbou Flexible hoses should ring products not be subject to abrasion kinking or permanent deformation 1 2 3 47 ST 6 Installation Instructions Natural Gas For Natural Gas usage the gas supply is connected to the regulator which is supplied loose with a built in test point 1kPa 4 WG and the inlet connection of 1 2 B S P male thread Do not over tighten The test point pressure should be preset to 1 0 kPa with the wok and semi rapid burners operating at maximum LP Gas For LPG usage the gas supply for the appliance must be regulated to a pressure of 2 75kPa 11 WG See Conversion to a different gas type Gas Supply Connection Check The connection point shall be accessible with the appliance installed To enable the gas supply to be readily shut off the gas supply must be connected with an isolating valve close to the product After installation and maki chec ng all connections thoroughly for possible leaks all control knobs on the unit to off ion Turn posi Open the valve on the gas supply suitable leak detection fluid solution e g Rocol check each gas connection one at a time by brushing the solution over the connection Using a he presence of bu
8. ng or using this product Please make this information available to the person responsible for installing the product as it could reduce your installation costs These products are registered in New Zealand at www ess govt nz and in Australia with AGA at www gas asn au Before You Start Prior to installation ensure that the local distribution conditions nature of gas and pressure and the adjustment of the product are compatible For adjustment conditions for this product see Gas Rate Summary This gas hob must be connected to a 220V 240V 50Hz power supply only and must be earthed via the power cord Ensure a suitable disconnection switch s incorporated in the permanent wiring mounted and positioned to comply with the local wiring rules and regulations A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules unless the ocal wiring rules allow for alternative means Ensure that there is a power outlet within reach of the cooktop cable 900 mm from he rear right of the product This must be accessible after installation The mains cable should not touch any metal parts ake the bench top of a heat resistan material Seal exposed bare edges of the cutout with an oil based paint or moisture proof polyurethane to prevent possible damage from moisture creeping between the cooktop trim and the ben
9. re progressive venturi adjustment on the wok burner ig 3 Lifting Off move the venturi closer to the orifice Fig 4 Yellow Tipping move the venturi way from the orifice g 5 Good Flame figure 6 TI O The label supplied with the orifices should be placed over the existing gas type label located on the underside of the product to indicate the gas change Installation Instructions Gas Rate Summary Natural Gas LPG Orifice size MJ hal kPa Orifice size MJ ha2 75 kPa CG602 Auxiliary Burner RH front 3 6 MJ h 3 9 MJ h Semi Rapid Burner LH amp RH rear 8 5 MJ h 8 4 MJ h Wok Burner LF front 15 MJ h 15 MJ h Rapid Burner LH front 12 MJ h 13 MJ h CG902 Auxiliary Burner RH front 3 7 MJ h 4 1 MJ h Semi Rapid Burner LH amp RH rear E 7 9 MJ h 7 9 MJ h Fish Burner Centre 10 MJ h 10 MJ h Wok Burner LH fi 15 MJ h 15 MJ h GC913T Simmer Burner RH front Semi Rapid Burner LH rear Rapid Burner LH front amp RH rear Wok Burner Cen CG913TM Simmer Burner RH front Semi Rapid Burner LH rear Rapid Burner LH front amp RH rear Wok Burner Centre Customer Care Current Information New Zealand Current Installation Instructions Product PO Box 58732 Greenmount Auckland dimensions and specifications are available Toll Free 0800 FP CARE 0800 37 2273 on the Fisher amp Paykel web site Fax 09 273 0656 Email customer careafp co nz www fisherpaykel com Australia
10. t Hazard Beware of sharp edges Replace the wok orifice with the correct one using a 10 mm spanner Reset the venturi see fig 2 Loosen the venturi screw move the venturi toward the orifice approx 2 mm 10 To refit the CG913 series hob tray repeat steps 6 and 7 in reverse 11 Check insulation resistance and earth continuity continued Installation Instructions 12 Turn on main electrical supply and light the Minimum Setting or Turn Down burners N This has been set at the factory for NG but 13 Important Reset the minimum setting may need adjusting for local conditions see Minimum Setting or Turndown 14 check all burners have good flame see E When converting to LPG the minimum fig 3 4 5 setting MUST be reset for each burner To adjust the minimum setting you will need a 2 5 x 45 mm screwdriver 1 Ignite the burner and set the knob to its minimum position Venturi 2 Remove the knob figure 2 3 Rotate the turn down screw slowly until a minimum regular flame is achieved The flame will diminish when the screw is turned clockwise and increase when turned anti clockwise see fig 6 Replace the knob 5 When the setting is right check regulation figure 3 figure 4 by quickly rotating the knob from the maximum to the minimum delivery position The flame must not go out figure 5 ote CG913TM models may requi
Download Pdf Manuals
Related Search