Extron electronic LPVM-1 User's Manual
Contents
1. Type VESA Mount Holes Locking Screws 10 32 Phillips Bottom Edge e Four screws or bolts to attach the LPVM 1 to the wall these must be appropriate for the type of wall Installation Instructions To VESA mount a touch panel or monitor using the LPVM 1 follow these instructions Disassembling the LPVM 1 1 Use a Phillips screwdriver to loosen the two locking screws until the two plates of the LPVM 1 can separate 2 Swing the bottom tabs of plate 1 away from the bottom edge of plate 2 w 4 Select a suitable mounting site and decide whether the LPVM 1 will be mounted directly to the wall see below or to a mud ring or UL certified junction box see the next page Mounting the LPVM 1 Directly to a Wall a Ifthe LPVM 1 is being mounted directly to drywall you may cut a hole in the drywall that is 2 5 x 2 5 inches 6 35 x 6 35 cm to run cables inside the wall cavity If the LPVM 1 is attached to a solid wall or you do not want to run cables through the drywall cavity the cables should be enclosed in conduit or raceway b Use plate 1 to mark the position of the four holes in the wall and drill four holes using a drill bit that is appropriate for the wall type Plate 1 accommodates screws up to 1 4 inch in diameter c Secure plate 1 to the wall with four screws or bolts that are appropriate for the wall type Ensure the tongue is facing up Pull plate 1 down to remove the tongue from the groov2. Overview The Extron Low Profile VESA Mount Kit LPVM 1 allows monitors or Extron touch panels to be wall mounted to a two gang UL certified junction box a two gang mud ring or directly onto any solid surface such as brick wood masonry or drywall The kit supports both the B type 20 x 50 mm and D type 75 x 75 mm VESA mounting patterns The monitor attaches to the wall at a fixed angle with no tilting CAUTION The maximum loads for the LPVM 1 are VESA B 4 4 pounds 2 kg VESA D 30 8 pounds 14 kg if the LPVM 1 is mounted directly to the wall not a mud ring The kit consists of two separate steel plates held together by two locking screws Plate 1 which attaches to the wall has a protruding tongue at the top The tongue fits into a groove at the top of plate 2 which attaches to the back of the display device see the figure at right Optional Tools and Equipment To mount the LPVM 1 you may need some or all of the following items that are not provided by Extron e Mud ring or UL certified junction box e Tools for cutting a hole in drywall e Conduit or surface raceway e Power drill with a bit that is appropriate for the wall type e Screwdriver Low Profile VESA Mount Kit User Guide Extron LPVM 1 Plate 1 D Type VESA Mount Holes Extron LPVM 1 Plate 2 Holes to Secure Plate 1 to Wall Bottom Tabs 2 Holes to Secure Plate 1 to Mud Ring or Junction Box Groove B
3. e in plate 2 Screws 4 Appropriate to Wall Type Low Profile VESA Mount Kit User Guide Continued 10 Mounting the LPVM 1 to a Mud Ring or UL Certified Junction Box in Drywall NOTE See the caution on previous page about weight restrictions a Follow the instructions provided by the manufacturer to cut the hole and install the mud ring or junction box UL certified 2 gang b Attach plate 1 to the mud ring or junction box using 4 8 the four 6 32 screws provided Ensure the tongue is facing upwards c Connect conduit to the junction box and run the cables to the installation site _ 6 32 screws 4 Extron ei LPVM 1 Mounting the Display Device Plate 1 If necessary remove all cables from the display device NOTE To VESA mount the TLP 700TV it is necessary to remove the base and the plastic enclosure from the back For full instructions see the TLP 700MV and TLP 700TV User Guide which is available from www extron com Do not use the VM 700T for mounting with the LPVM 1 Use the four 12 mm M4 screws provided to attach plate 2 to the back of the display device using either the B type 20 x 50 mm or D type 75 x 75 mm VESA mounting pattern The plate should be attached securely but do not over tighten the screws Sa Attach the cables to the back of the display device Feed any excess 12 mm M4 Screws 4 cable back into the wall conduit or raceway Follow a
4. ll information in the user manual provided with the display device to ensure the cables and power are connected correctly Monitor w B type VESA Mount Check the display device is working correctly see the user manual for the display device Hook plate 2 to plate 1 by holding the display at a slight angle so that the groove of plate 2 is over the tongue in plate 1 Lower the display device so that the tongue enters the groove as far as possible Allow the bottom of the display to move inwards so that the display is parallel to the wall and the bottom tabs of plate 1 are seated over the bottom edge of plate 2 Lock the two plates together by tightening the two locking screws with a screwdriver do not over tighten Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters 800 633 9876 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 833 1568 971 4 2991800 Inside USA Canada Only Inside USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX 68 1946 01 1 714 491 1500 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 Rev A 1 714 491 1517 FAX 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX 06 10 2010 Extron Electronics All Rights Reserved WWw extron com
Download Pdf Manuals
Related Search